RESUMO
Diamine-appended Mg2(dobpdc) (dobpdc4- = 4,4'-dioxidobiphenyl-3,3'-dicarboxylate) metal-organic frameworks are promising candidates for carbon capture that exhibit exceptional selectivities and high capacities for CO2. To date, CO2 uptake in these materials has been shown to occur predominantly via a chemisorption mechanism involving CO2 insertion at the amine-appended metal sites, a mechanism that limits the capacity of the material to â¼1 equiv of CO2 per diamine. Herein, we report a new framework, pip2-Mg2(dobpdc) (pip2 = 1-(2-aminoethyl)piperidine), that exhibits two-step CO2 uptake and achieves an unusually high CO2 capacity approaching 1.5 CO2 per diamine at saturation. Analysis of variable-pressure CO2 uptake in the material using solid-state nuclear magnetic resonance (NMR) spectroscopy and in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) reveals that pip2-Mg2(dobpdc) captures CO2 via an unprecedented mechanism involving the initial insertion of CO2 to form ammonium carbamate chains at half of the sites in the material, followed by tandem cooperative chemisorption and physisorption. Powder X-ray diffraction analysis, supported by van der Waals-corrected density functional theory, reveals that physisorbed CO2 occupies a pocket formed by adjacent ammonium carbamate chains and the linker. Based on breakthrough and extended cycling experiments, pip2-Mg2(dobpdc) exhibits exceptional performance for CO2 capture under conditions relevant to the separation of CO2 from landfill gas. More broadly, these results highlight new opportunities for the fundamental design of diamine-Mg2(dobpdc) materials with even higher capacities than those predicted based on CO2 chemisorption alone.
RESUMO
Developing a desirable ethanol dehydrogenation process necessitates a highly efficient and selective catalyst with low cost. Herein, we show that the "complex active site" consisting of atomically dispersed Au atoms with the neighboring oxygen vacancies (Vo) and undercoordinated cation on oxide supports can be prepared and display unique catalytic properties for ethanol dehydrogenation. The "complex active site" Au-Vo-Zr3+ on Au1/ZrO2 exhibits the highest H2 production rate, with above 37,964â mol H2 per mol Au per hour (385â g H2 g Au - 1 ${{\rm{g}}_{{\rm{Au}}}^{ - 1} }$ h-1) at 350 °C, which is 3.32, 2.94 and 15.0â times higher than Au1/CeO2, Au1/TiO2, and Au1/Al2O3, respectively. Combining experimental and theoretical studies, we demonstrate the structural sensitivity of these complex sites by assessing their selectivity and activity in ethanol dehydrogenation. Our study sheds new light on the design and development of cost-effective and highly efficient catalysts for ethanol dehydrogenation. Fundamentally, atomic-level catalyst design by colocalizing catalytically active metal atoms forming a structure-sensitive "complex site", is a crucial way to advance from heterogeneous catalysis to molecular catalysis. Our study advanced the understanding of the structure sensitivity of the active site in atomically dispersed catalysts.
RESUMO
Layer-by-layer (LbL) assembly of oppositely charged materials has been widely used as an approach to make two-dimensional (2D) nanosheet-based membranes, which often involves 2D nanosheets being alternately deposited with polymer-based polyelectrolytes to obtain an electrostabilized nanosheet-polymer structure. In this study, we hypothesized that using 2D nanosheets with matching physical properties as both polyanions and polycations may result in a more ordered nanostructure with better stability than a nanosheet-polymer structure. To compare the differences between nanosheet-nanosheet vs nanosheet-polymer structures, we assembled negatively charged molybdenum disulfide nanosheets (MoS2) with either positively charged graphene oxide (PrGO) nanosheets or positively charged polymer (PDDA). Using combined measurements by ellipsometer and quartz crystal microbalance with dissipation, we discovered that the swelling of MoS2-PrGO in ionic solutions was 60% lower than that of MoS2-PDDA membranes. Meanwhile, the MoS2-PrGO membrane retained its permeability upon drying, whereas the permeability of MoS2-PDDA decreased by 40% due to the restacking of MoS2. Overall, the MoS2-PrGO membrane demonstrated a better filtration performance. Additionally, our X-ray photoelectron spectroscopy results and analysis on layer density revealed a clearer transition in material composition during the LbL synthesis of MoS2-PrGO membranes, and the X-ray diffraction pattern suggested its resemblance to an ordered, layer-stacked structure. In conclusion, the MoS2-PrGO membrane made with nanosheets with matching size, shape, and charge density exhibited a much more aligned stacking structure, resulting in reduced membrane swelling under high salinity solutions, controlled restacking, and improved separation performance.
RESUMO
This study presents a novel approach to developing high-performance lithium-ion battery electrodes by loading titania-carbon hybrid spherogels with sulfur. The resulting hybrid materials combine high charge storage capacity, electrical conductivity, and core-shell morphology, enabling the development of next-generation battery electrodes. We obtained homogeneous carbon spheres caging crystalline titania particles and sulfur using a template-assisted sol-gel route and carefully treated the titania-loaded carbon spherogels with hydrogen sulfide. The carbon shells maintain their microporous hollow sphere morphology, allowing for efficient sulfur deposition while protecting the titania crystals. By adjusting the sulfur impregnation of the carbon sphere and varying the titania loading, we achieved excellent lithium storage properties by successfully cycling encapsulated sulfur in the sphere while benefiting from the lithiation of titania particles. Without adding a conductive component, the optimized material provided after 150 cycles at a specific current of 250 mA g-1 a specific capacity of 825 mAh g-1 with a Coulombic efficiency of 98%.
RESUMO
Inkjet printing is a more sustainable and scalable fabrication method than spin coating for producing perovskite solar cells (PSCs). Although spin-coated SnO2 has been intensively studied as an effective electron transport layer (ETL) for PSCs, inkjet-printed SnO2 ETLs have not been widely reported. Here, we fabricated inkjet-printed, solution-processed SnOx ETLs for planar PSCs. A champion efficiency of 17.55% was achieved for the cell using a low-temperature processed SnOx ETL. The low-temperature SnOx exhibited an amorphous structure and outperformed high-temperature crystalline SnO2. The improved performance was attributed to enhanced charge extraction and transport and suppressed charge recombination at ETL/perovskite interfaces, which originated from enhanced electrical and optical properties of SnOx, improved perovskite film quality, and well-matched energy level alignment between the SnOx ETL and the perovskite layer. Furthermore, SnOx was doped with Cu. Cu doping increased surface oxygen defects and upshifted energy levels of SnOx, leading to reduced device performance. A tunable hysteresis was observed for PSCs with Cu-doped SnOx ETLs, decreasing at first and turning into inverted hysteresis afterwards with increasing Cu doping level. This tunable hysteresis was related to the interplay between charge/ion accumulation and recombination at ETL/perovskite interfaces in the case of electron extraction barriers.
RESUMO
MXene is investigated as an electrode material for different energy storage systems due to layered structures and metal-like electrical conductivity. Experimental results show MXenes possess excellent cycling performance as anode materials, especially at large current densities. However, the reversible capacity is relatively low, which is a significant barrier to meeting the demands of industrial applications. This work synthesizes N-doped graphene-like carbon (NGC) intercalated Ti3C2Tx (NGC-Ti3C2Tx) van der Waals heterostructure by an in situ method. The as-prepared NGC-Ti3C2Tx van der Waals heterostructure is employed as sodium-ion and lithium-ion battery electrodes. For sodium-ion batteries, a reversible specific capacity of 305 mAh g-1 is achieved at a specific current of 20 mA g-1, 2.3 times higher than that of Ti3C2Tx. For lithium-ion batteries, a reversible capacity of 400 mAh g-1 at a specific current of 20 mA g-1 is 1.5 times higher than that of Ti3C2Tx. Both sodium-ion and lithium-ion batteries made from NGC-Ti3C2Tx shows high cycling stability. The theoretical calculations also verify the remarkable improvement in battery capacity within the NGC-Ti3C2O2 system, attributed to the additional adsorption of working ions at the edge states of NGC. This work offers an innovative way to synthesize a new van der Waals heterostructure and provides a new route to improve the electrochemical performance significantly.
RESUMO
The Hume-Rothery rules governing solid-state miscibility limit the compositional space for new inorganic material discovery. Here, we report a non-equilibrium, one-step, and scalable flame synthesis method to overcome thermodynamic limits and incorporate immiscible elements into single phase ceramic nanoshells. Starting from prototype examples including (NiMg)O, (NiAl)Ox, and (NiZr)Ox, we then extend this method to a broad range of Ni-containing ceramic solid solutions, and finally to general binary combinations of elements. Furthermore, we report an "encapsulated exsolution" phenomenon observed upon reducing the metastable porous (Ni0.07Al0.93)Ox to create ultra-stable Ni nanoparticles embedded within the walls of porous Al2O3 nanoshells. This nanoconfined structure demonstrated high sintering resistance during 640 h of catalysis of CO2 reforming of methane, maintaining constant 96% CH4 and CO2 conversion at 800 °C and dramatically outperforming conventional catalysts. Our findings could greatly expand opportunities to develop novel inorganic energy, structural, and functional materials.
RESUMO
Nanoporous carbon materials with customized structural features enable sustainable and electrochemical applications through improved performance and efficiency. Carbon spherogels (highly porous carbon aerogel materials consisting of an assembly of hollow carbon nanosphere units with uniform diameters) are desirable candidates as they combine exceptional electrical conductivity, bespoke shell porosity, tunability of the shell thickness, and a high surface area. Herein, we introduce a novel and more environmentally friendly sol-gel synthesis of resorcinol-formaldehyde (RF) templated by polystyrene spheres, forming carbon spherogels in an organic solvent. By tailoring the molar ratio of resorcinol to isopropyl alcohol (R/IPA) and the concentration of polystyrene, the appropriate synthesis conditions were identified to produce carbon spherogels with adjustable wall thicknesses. A single-step solvent exchange process from deionized water to isopropyl alcohol reduces surface tension within the porous gel network, making this approach significantly time and cost-effective. The lower surface tension of IPA enables solvent extraction under ambient conditions, allowing for direct carbonization of RF gels while maintaining a specific surface area loss of less than 20% compared to supercritically dried counterparts. The specific surface areas obtained after physical activation with carbon dioxide are 2300-3600 m2 g-1. Transmission and scanning electron microscopy verify the uniform, hollow carbon sphere network morphology. Specifically, those carbon spherogels are high-performing electrodes for energy storage in a supercapacitor setup featuring a specific capacitance of up to 204 F g-1 at 200 mA g-1 using 1 M potassium hydroxide (KOH) solution as the electrolyte.