Bacterial adhesion and surface roughness of particulate-filled and short fiber-reinforced composites.

The objective of the study was to assess the initial adhesion of Streptococcus mutans (S. mutans) and surface roughness of different particulate-filled (PFC) and short fiber-reinforced (SFRC) composites. Five PFC composites (CeramX Universal, Filtek Universal, Omnichroma, Tetric Prime and Venus Diamond) and four SFRC composites (everX Posterior, everX Flow Bulk, everX Flow Dentin and experimental packable SFRC) were tested in this study. A non-contact 3D profilometer was employed to assess the surface roughness (Ra) of the polished specimens (using 4000-grit abrasive paper). For the bacterial adhesion test, the specimens (n = 5/group) were immersed in a solution of S. mutans to facilitate initial adhesion. To determine the number of cells on the surfaces of the discs as colony-forming units (CFU), the vials holding the microbial samples were highly agitated using a vortex machine. Subsequently, the samples were diluted multiple times and anaerobically incubated for 48 h at 37 °C on Mitis Salivarius Agar plates (Difco) supplemented with bacitracin. Bacterial adherence assessment was performed using SEM. The data were analyzed using ANOVA. All tested PFC and SFRC composites showed similar adhesion of S. mutan. The lowest Ra values (0.26 µm) (p < 0.05) were found in the flowable SFRCs (everX Flow Bulk & Dentin), while the highest values (p < 0.05) were observed in CeramX and everX Posterior (0.42 µm). Experimental SFRC had comparable Ra value (0.38 µm) than other commercial composites. The presence of short microfibers in the composite appeared to have no adverse effects on the initial adhesion of bacteria or the surface roughness.

Fracture behavior of short fiber-reinforced CAD/CAM inlay restorations after cyclic fatigue aging.

The aim of this study was to assess the fracture behavior of molar teeth restored with MOD inlays made of experimental short fiber-reinforced CAD/CAM composite block (SFRC CAD) before and after cyclic fatigue aging. Standardized MOD cavities were prepared on 60 intact mandibular molars. Three groups of CAD/CAM made inlay restorations (Cerasmart 270, Enamic, and SFRC CAD) were fabricated (n = 20/group). All restorations were luted with self-adhesive dual-cure resin cement (G-Cem One). Half of restored teeth per each group (n = 10) were quasi-statically loaded until fracture without aging. The other half underwent cyclic fatigue aging for 500,000 cycles (Fmax = 150 N) before being loaded quasi-statically until fracture. Then, the fracture type was visually inspected. The microstructure and elemental content of CAD/CAM materials were assessed using SEM and EDS. Two-way analysis of variance (ANOVA) was used to statistically examine the data, and it was followed by the Tukey HSD test (α = 0.05). ANOVA demonstrated that both material type and aging had a significant effect (p < 0.05) on the load-bearing capacity values of the restorations. Teeth restored with SFRC CAD showed significantly the highest (p < 0.05) load-bearing capacity (2535 ± 830 N) after fatigue aging among all groups. SEM images showed the ability of short fibers in SFRC CAD composite to redirect and hinder crack propagation. With regard to fracture mode, Enamic group revealed 85% of catastrophic failure (vs. 45% and 10% for Cerasmart 270 and SFRC CAD, respectively). Large MOD cavities on molar teeth were most favorably restored with SFRC CAD inlays, yielding the highest load-bearing capacity and more restorable failures.

Co-Influence of Restoration Bonding and Inlay Cavity Design on Fracture Load of Restored Tooth.

INTRODUCTION: The aim of this study was to investigate the co-influence of indirect mesio- occlusal-distal (MOD) cavity geometry and inlay restoration bonding on quasi-static fracture load of the restored tooth. METHODS: Forty-eight intact human molar teeth were selected and prepared for standardized edge-shaped or round-shaped MOD cavities. The resin composite (Cerasmart, GC) inlays were bonded with the state-of-the-art inlay bonding protocol or with intentionally deteriorated bonding using n-hexane-wax solution for preconditioning. Restored teeth were loaded along the long axis of the tooth. Ultimate fracture load was recorded, and the type of fracture was visually determined and classified. Statistical analysis of load values was performed by Kruskal-Wallis test. RESULTS: Round-shaped cavity design with bonded restoration presented the highest fracture load (1658N). Bonding had significant influence on the fracture load of roundshaped cavity design (p=0.0003), whereas cavity design had no influence when the bonding was deteriorated (p=0.8075). In the case of deteriorated bonding, either the inlay or tooth fractured separately whereas in the bonded inlays fractures were commonly found both in the tooth and inlay. CONCLUSIONS: According to this study, bonded inlay restoration increased fracture resistance, while cavity design had no statistical difference on fracture resistance of the restored tooth.

Evaluation of fracture behavior in short fiber-reinforced direct and indirect overlay restorations.

OBJECTIVES: The aim was to assess how incorporating a short-fiber composite (SFC) core would affect the fracture behavior of direct and indirect overlays. Furthermore, to examine the relationship between the thickness ratio of SFC core to particulate-filled composite (PFC) veneering and the fracture-behavior of bilayered-structured restorations. MATERIALS AND METHODS: A total of 120 molars were used to create MOD cavities, with palatal cusps removed. Four different groups of direct overlays were then made (n = 15/group), all of which featured a SFC core (everX Flow) with varying thicknesses (0, 1, 4, and 5 mm), as well as a surface layer of PFC (G-aenial Posterior), with the overall thickness of the bilayered-structured restoration set at 5 mm. Additionally, four groups of CAD/CAM restorations were created (Cerasmart 270 and Initial LiSi Block), with or without 2 mm of SFC core reinforcement. Following the fabrication of these restorations, cyclic fatigue aging was carried out for a total of 500,000 cycles, with an applied maximum load (Fmax) of 150 N. Subsequently, each restoration underwent quasi-static loading until fracture. The fracture mode was subsequently evaluated using optical microscopy and SEM. RESULTS: There were no statistically significant differences (p > 0.05) observed in the fracture resistance of indirect overlays reinforced with a 2-mm SFC core compared to those made solely from restorative materials. Direct overlays constructed using plain SFC or with a 4-mm layer thickness of SFC core exhibited significantly higher fracture resistance values (2674 ± 465 and 2537 ± 561 N) (p < 0.05) when compared to all other groups tested, according to the statistical analysis ANOVA. CONCLUSIONS: The most effective method for restoring large MOD cavities was found to be direct restoration using SFC either alone or as a bulk core in combination with PFC composite. CLINICAL RELEVANCE: The use of SFC as bulk reinforcing base will significantly improve the loading performance of directly layered restorations.

A comparative assessment of color stability among various commercial resin composites.

OBJECTIVES: The aim was to evaluate the color stability of six commercial restorative resin composites after being exposed to commonly consumed beverages. Repolishing impact on the stained composite was also assessed. METHODS: One-hundred and fifty disc specimens (8 mm diameter & 3 mm thickness) were prepared from Filtek™ Universal Restorative, SDR flow+, everX Flow, G-ænial A'CHORD, G-ænial Universal Flo and G-ænial Universal Injectable. To assess the color stability in five various beverages, 25 specimens from each material were randomly distributed into five groups (n = 5), according to the utilized staining solution. Group 1: distilled water, Group 2: coffee, Group 3: red wine, Group 4: energy drink, Group 5: coke. The color changes (∆E) for all materials were measured using spectrophotometer at the baseline, after 84 days of staining and after repolishing. Data was collected and analyzed using ANOVA (α = 0.05). RESULTS: Both material type and staining solution had a significant effect on the color stability of specimens (p < 0.05). Compared to other beverages, the color value of the specimens submerged in coffee and wine showed the most statistically significant (p < 0.05) mean ∆E. SDR flow + in coffee and wine presented the highest ∆E when compared to other tested materials (p < 0.05). After staining of the composites, repolishing was successful in lowering the ∆E value. CONCLUSIONS: All the beverages had an impact on the color stability of the tested resin composites, with coffee and wine demonstrating the most significant effects. The variations in color stability varied depending on the specific material utilized. Dentists should possess awareness regarding the chemical interactions that occur between different beverages and various types of resin composites. Additionally, repolishing serves as an effective technique for eliminating surface discoloration in composite restorations.

Direct Short-Fiber Reinforced Composite Resin Restorations and Glass-Ceramic Endocrowns in Endodontically Treated Molars: A 4 -Year Clinical Study.

To compare the clinical performance of direct and indirect cusp covering restorations in endodontically treated molars (ETMs). Eighteen ETMs in sixteen patients were randomly assigned into one of the two study groups:Group 1 (SFCRs) direct composite restorations with a short fiber-reinforced base, and Group 2 (GCEs) indirect glass-ceramic endocrowns. Eleven teeth were allocated to Group 1 and seven teeth to Group 2. Restorations were prepared in the student clinic between November 2012 and January 2015, and were evaluated at baseline and after 4.0 years according to modified USPHS criteria. The number of visits required for fabrication and maintenance of restorations were also compared. Two-way ANOVA was used to evaluate the differences between the groups (p=0.05). One SFCR and one GCE were lost due to secondary caries and endodontic complications, resulting in a 4-year survival rate of 90.9% and 85.7% respectively. Two SFCRs required minor grinding and polishing due to chipping or gloss loss, and two SFCRs needed repair due to secondary caries or loss of proximal contact. One GCE required occlusal adjustment. GCEs showed smoother surface texture and better-preserved anatomic morphology. SFCRs required more maintenance, were simpler to produce, needed usually one visit and repairs were easier to perform.

Influence of short-fiber composite base on fracture behavior of direct and indirect restorations.

OBJECTIVES: The aim was to examine the influence of short-fiber composite (SFC) core on the fracture-behavior of different types of indirect posterior restorations. In addition, the effect of thickness ratio of SFC-core to the thickness of the veneering conventional composite (PFC) on fracture-behavior of bi-structured composite restorations was evaluated. MATERIALS AND METHODS: MOD cavities with removed palatal cusps were prepared on 90 intact molars. Five groups of direct overlay restorations (n = 10/group) were fabricated having a SFC-core (everX Flow) with various thicknesses (0, 1, 2, 3, 4 mm) and layer of surface PFC (G-aenial Anterior), remaining the thickness of the bi-structure restoration to be 5 mm. Four groups of CAD/CAM-made restorations (Cerasmart 270 and e-max CAD) were fabricated either with 2-mm layer of SFC-core or without fiber reinforcement. Intact teeth (n = 10) were used as control group. Restorations were statically loaded until fracture. Fracture patterns were evaluated visually. Data were analyzed using ANOVA (p = 0.05). RESULTS: With indirect overlay restorations, no statistically significant differences (p > 0.05) were observed in the load-bearing capacities between restorations reinforced by 2-mm SFC-core (bi-structured) and those fabricated from plain restorative materials. ANOVA displayed that direct overlay restorations made from 4-mm layer thickness of SFC-core had significantly higher load-bearing capacities (3050 ± 574 N) (p < 0.05) among all the groups tested. CONCLUSIONS: Restorations (direct/indirect) combining SFC-core and a surface layer of conventional material demonstrated encouraging achievement in reference to fracture behavior. CLINICAL RELEVANCE: The use of flowable short-fiber composite as reinforcing base with large direct and indirect restorations may result in more repairable failure.

Microstructure and Surface Characteristics of Short- Fiber Reinforced CAD/CAM Composite Blocks.

OBJECTIVE: The aim was to investigate certain surface properties and microstructure of an experimental short fiber-reinforced CAD/CAM composite block (SFRC) in comparison with different CAD/CAM, 3D-printing and manually-made commercial composites (Cerasmart 270, GC Temp PRINT, Pro3dure GR-17, Essentia U, Gradia Plus and everX Flow). METHODS: A wear-test was performed using a chewing-simulator with 15000 cycles. Wear depth (n=6) was assessed by 3D optical-profilometer. Surface roughness (SR) before and after wearing-test was evaluated. A Vickers-indenter was utilized for evaluating surface microhardness (VH) and glossmeter was utilized to measure the surface gloss at 60°. The surface microstructure of each composite was investigated with SEM. Data were statistically analyzed with analysis of variance ANOVA (p=0.05). RESULTS: Significant differences in the surface properties were found according to the type of composite (p⟨0.05). Cerasmart 270 exhibited the highest VH (94.8 V) and lowest SR (0.18 Ra) values (p⟨0.05) among the composites tested. The lowest wear depth measurement was located for GC Temp PRINT (19.3 µm) which was not significantly different (p⟩0.05) from Cerasmart 270 (20.7 µm). CONCLUSION: Incorporation of fibers to the composite of the CAD/CAM block did not negatively influence the surface characteristics of composite.

Influence of Short Fiber- Reinforced Composites on Fracture Resistance of Single-Structure Restorations.

OBJECTIVE: The aim was to determine the load-bearing capacity of anterior crowns prepared using two types of single-structure short fibre-reinforced composites (SFRCs). Furthermore, fracture toughness (FT), flexural strength (FS) and flexural modulus (FM) of tested composites were measured. METHODS: Seven groups of composite crowns were designed for an upper central incisor (n=8/group). Two groups were CAD/CAM fabricated made of Cerasmart 270 and experimental single-structure SFRC blocks. Two groups were 3D-printed made of GC Temp PRINT and Pro3dure GR-17 composites. Two groups were made of conventional light-cured composites (Essentia and Gradia Plus). The last group was a single-structure SFRC made of commercial flowable SFRC (everX Flow). Crown restorations were loaded until fracture. Failure-modes were then visually examined. FT, FS and FM were determined for each tested composite (n=8). The data were analysed using analysis of variance (p=0.05) followed by Tukey's post-hoc test. RESULTS: ANOVA revealed that crowns made of experimental SFRC blocks had significantly higher load-bearing capacities (1650 ±230 N) (p⟨0.05) among all the groups tested. Experimental SFRC blocks exhibited the highest FT (2.9 MPa m1/2) and FS (245.8 MPa) values (p⟨0.05) among tested composites. CONCLUSION: CAD/CAM fabricated restorations made of experimental SFRC blocks demonstrated encouraging performance related to their fracture-behaviour.

Fiber Reinforcement of Endodontically Treated Teeth: What Options Do We Have? Literature Review.

The restoration of endodontically treated teeth (ETT), even though practiced for many years, remains a major concern in dentistry. There is a variety of materials and clinical techniques advocated for restoring ETT and hundreds of studies devoted to this subject have been published in the dental literature. This narrative review article was undertaken to answer a question regarding restoration of ETT with available evidence: What fiber reinforcement options do we have other than prefabricated fiber post? Using a Medline search (up to 2019) and resulting cross-references, authors selected original research on the topic of fiber-reinforced composite (FRC) and restoration of ETT. Of the assessed articles selected (n=79), most were laboratory-based research with various test specimen designs and only 15 articles were clinical reports. From the reviewed studies, using individually formed FRC posts and short-FRC resin showed promising characteristics, and therefore, might be recommended as an alternative treatment option in restoring ETT. However, long-term clinical trials are needed in order to evaluate the usefulness of these alternatives.

Accuracy of inlay and onlay restorations based on 3D printing or milling technique - a pilot study.

PURPOSE: To evaluate and compare the accuracy of 3D printing versus CAD/CAM milling in the fabrication of inlay/onlay restorations based on pilot experiments. MATERIAL AND METHODS: Different shaped inlay/onlay cavities were prepared on six extracted and root canal treated human molar teeth. Digital impressions were taken with a CEREC AC Omnicam© intraoral scanner. Based on the same impression data, nano-ceramic restorations were performed using milling (M group) and composite restorations (from material not for clinical use) using Multijet 3D printing technology (3D group). The accuracy was evaluated by measuring the marginal and internal gaps based on x-ray microtomography 3D imaging scans. The internal fit was evaluated using a replica technique with A-silicone impressions and weighing. RESULTS: The 3D group restorations showed better marginal and internal fit values. The mean internal gap values of the 3D group restorations were 40-60% lower compared to the M group restorations, the difference being statistically significant at most measuring points (p⟨0.05, t-test). CONCLUSIONS: The accuracy of the Multijet 3D printing is at least at the same level as the milling technique in the fabrication of dental inlay/onlay restorations. Additional investigations are needed to develop the 3D printing process and suitable materials for dental applications.

Effect of Distance on Light Transmission Through Polymerized Resin Composite.

OBJECTIVE: Light transmittance of dental composites varies between products and shades, but also light curing units differ to each other in their irradiance and fiber optic structure of curing tip. The aim of this study was to investigate whether there is linear relationship between the distance of the curing tip to the resin composite and irradiance at lower surface of the resin composite. MATERIALS AND METHODS: Disks of 1 mm thickness (6mm diameter) were fabricated. Light transmittance (intensity) through the disk was measured at distance of 0, 2, 4, 6, 8, 10 mm from the light tip with two light curing units Elipar S10 (3M-ESPE) and Silverlight (GC). Irradiance ratio (irradiance on the sensor surface without the composite disk / with the composite disk) was calculated and plotted against the distance of the light curing tip. Statistical analysis was carried out using analysis of covariance (ANCOVA, Tukey's, α =0.05). RESULTS: Irradiance ratio varied between 18% to 24% with Silverlight and 21% to 26% with Elipar S10 light curing units. There were statistically significant differences between the ratios with different distances of the light curing tip (p⟨0.05). Interestingly, the highest irradiance ratio for Elipar S10 unit was found with 4 mm distance of the tip, whereas Silverlight unit had the highest ratio with 6 mm distance. Out of two tested resin composites, the flowable composite showed higher irradiance ratio than regular packable resin composite. CONCLUSIONS: Increase of distance of the light curing tip from the composite surface decreased the absolute irradiance underneath of composite, as expected. However, there seemed to be device dependent optimal distance of 4-6 mm to reach the most efficient irradiance ratio through the composite resin keeping in mind that most efficient transmission of light through the material is reached by having light curing tip in contact to the material.

Effect of several intracanal medicaments on the push-out bond strength of ProRoot MTA and Biodentine.

AIM: To evaluate the effect of prior application of several intracanal medicaments on the push-out bond strength of ProRoot MTA and Biodentine. METHODOLOGY: Sixty freshly extracted maxillary anterior teeth were sectioned below the cementoenamel junction, and the root canals instrumented using rotary files. Thereafter, a parallel post drill was used to obtain a standardized root canal dimension. The roots were randomly assigned into one of the following groups with respect to the intracanal medicament applied: group 1: calcium hydroxide (CH) powder (Merck, Darmstadt, Germany) mixed with distilled water; group 2: a mixture of metronidazole, ciprofloxacin and minocycline (triple antibiotic paste); group 3: a combination of amoxicillin and clavulanic acid (Augmentin; Champs Pharmacy, San Antonio, TX, USA); group 4: an antibiotic-corticoid compound paste (Ledermix; Riemser, Greifswald, Germany); and group 5: no medicament (control). Following removal of medicaments with instrumentation and irrigation, the roots were cut into 1-mm-thick parallel transverse sections in a coronal-to-apical direction (5 slices/tooth). Thereafter, the specimens were divided into two subgroups according to the calcium silicate cement applied (n = 30/group): (i) ProRoot MTA (Dentsply Tulsa Dental, Tulsa, OK, USA) and (ii) Biodentine (Septodont, Saint-Maur-des-Fosses, France). A push-out test was performed, and the data were analysed statistically using two-way anova and Tukey's post hoc test. RESULTS: Regardless of the type of intracanal medicament used, Biodentine had significantly higher bond strength than MTA (P < 0.05). The highest push-out bond strength results were obtained in CH-treated dentine. Compared with other medicaments, this value was only significantly higher than that of Ledermix (P < 0.05). In both the MTA and Biodentine groups, pairwise comparisons between other medicaments showed similar debonding values (P > 0.05). CONCLUSIONS: Biodentine had a higher bond strength to root canal dentine than ProRoot MTA. Prior CH in distilled water intracanal placement increased the dislodgment resistance of both calcium silicate cements.

Fracture strengths of chair-side-generated veneers cemented with glass fibers.

INTRODUCTION: CAD/CAM (computer-aided design and computer-aided manufacturing) systems have refreshed the idea of chair-side production of restorations, but the fracture of ceramic veneers remains a problem. Cementation with glass fibers may improve the fracture strengths and affect the failure modes of CAD/CAM-generated ceramic veneers. Therefore, this study compared the fracture strengths of ceramic veneers produced at chair side and cemented with or without glass fibers with those of composite veneers. METHODOLOGY: Thirty intact mandibular incisors were randomly divided into three groups ( n = 10) and treated with CAD/CAM-fabricated veneers cemented with dual-cure composite resin luting cement (CRLC; Group 1), CAD/CAM-fabricated veneers cemented with a glass fiber network (GFN) and dual-cure CRLC (Group 2), and a direct particulate filler composite veneer constructed utilizing fiber and a restorative composite resin (Group 3). The specimens were tested with a universal testing machine after thermal cycling treatment. RESULT: The loads at the start of fracture were the lowest for traditionally fabricated composite veneers and higher for CAD/CAM-generated. Veneers cemented either without or with the GFN. The failure initiation loads (N) for the veneers were 798.92 for Group 1, 836.27 for Group 2, and 585.93 for Group 3. The predominant failure mode is adhesive failure between the laminates and teeth for Group 1, cohesive failure in the luting layer for Group 2, and cohesive laminate failure for Group 3, which showed chipping and small fractures. CONCLUSION: Ceramic material is a reliable alternative for veneer construction at chair side. Fibers at the cementation interface may improve the clinical longevity and provide higher fracture strength values.

Clinical Performance of Short Fibre-reinforced Glass Ionomer Cement Restorations in Cervical Carious Lesions: 12-Month Randomized Clinical Trial.

The aim was to assess the clinical performance of experimental short fiber-reinforced glass-ionomer cement (FR-GIC) in the treatment of cervical caries lesions. A total of 45 patients were randomly enrolled in this trial according to the split-mouth design. The FR-GIC was prepared by adding short glass fibers at a mass ratio of 20% into the powder portion of Fuji II LC. The cervical lesions in the intervention group were restored with FR-GIC, while unmodified Fuji II LC was applied as the control. Clinical evaluation was performed by two blinded operators at baseline, at 6, and 12 months using modified USPHS criteria. The data were analyzed using Friedman's test, followed by the Nemenyi post hoc test with a significance level of α = 0.05. After 1 year, all restorations were fully retained. There was no statistically significant difference (p⟩0.05) between the two materials based on the evaluated criteria. Both groups had 4 (10%) cases with Bravo scores for cavos-surface marginal discoloration. Regarding marginal integrity, Bravo scores were observed in 5 (12.5%) cases in the intervention group and 4 (10%) cases in the control group. Both materials in the treatment of cervical caries lesions demonstrated satisfactory clinical outcome throughout the 12-month follow-up.

Surface modification of fiber reinforced polymer composites and their attachment to bone simulating material.

The purpose of this study was to investigate the effect of fiber orientation of a fiber-reinforced composite (FRC) made of poly-methyl-methacrylate (PMMA) and E-glass to the surface fabrication process by solvent dissolution. Intention of the dissolution process was to expose the fibers and create a macroporous surface onto the FRC to enhance bone bonding of the material. The effect of dissolution and fiber direction to the bone bonding capability of the FRC material was also tested. Three groups of FRC specimens (n = 18/group) were made of PMMA and E-glass fiber reinforcement: (a) group with continuous fibers parallel to the surface of the specimen, (b) continuous fibers oriented perpendicularly to the surface, (c) randomly oriented short (discontinuous) fibers. Fourth specimen group (n = 18) made of plain PMMA served as controls. The specimens were subjected to a solvent treatment by tetrahydrofuran (THF) of either 5, 15 or 30 min of time (n = 6/time point), and the advancement of the dissolution (front) was measured. The solvent treatment also exposed the fibers and created a surface roughness on to the specimens. The solvent treated specimens were embedded into plaster of Paris to simulate bone bonding by mechanical locking and a pull-out test was undertaken to determine the strength of the attachment. All the FRC specimens dissolved as function of time, as the control group showed no marked dissolution during the study period. The specimens with fibers along the direction of long axis of specimen began to dissolve significantly faster than specimens in other groups, but the test specimens with randomly oriented short fibers showed the greatest depth of dissolution after 30 min. The pull-out test showed that the PMMA specimens with fibers were retained better by the plaster of Paris than specimens without fibers. However, direction of the fibers considerably influenced the force of attachment. The fiber reinforcement increases significantly the dissolution speed, and the orientation of the glass fibers has great effect on the dissolving depth of the polymer matrix of the composite, and thus on the exposure of fibers. The glass fibers exposed by the solvent treatment enhanced effectively the attachment of the specimen to the bone modeling material.

Effect of monomer composition of polymer matrix on flexural properties of glass fibre-reinforced orthodontic archwire.

To compare force levels obtained from glass fibre-reinforced composite (FRC) archwires. Specifically, FRC wires were compared with polymer matrices having different dimethacrylate monomer compositions. FRC material (E-glass provided by Stick Tech Ltd, Turku, Finland) with continuous unidirectional glass fibres and four different types of dimethacrylate monomer compositions for the resin matrix were tested. Cross-sectionally round FRC archwires fitting into the 0.3 mm slot of a bracket were divided into 16 groups with six specimens in each group. Glass fibres were impregnated by the manufacturer, and they were initially light-cured by hand light-curing unit or additionally post-cured in light-curing oven. The FRC archwire specimens were tested at 37°C according to a three-point bending test in dry and wet conditions using a span length of 10 mm and a crosshead speed of 1.0 mm/minute. The wires were loaded until final failure. The data were statistically analysed using analysis of variance (ANOVA). The dry FRC archwire specimens revealed higher load values than water stored ones, regardless of the polymer matrix. A majority of the FRC archwires showed higher load values after being post-cured. ANOVA revealed that the polymer matrix, curing method, and water storage had a significant effect (P < 0.05) on the flexural behaviour of the FRC archwire. Polymer matrix composition, curing method, and water storage affected the flexural properties and thus, force level and working range which could be obtained from the FRC archwire.

Flexural strength,water sorption and solubility of a methylmethacrylate-free denture base polymer reinforced with glass fibre reinforcement.

A methylmethacrylate-free denture base polymer (Eclipse) in comparison to a conventional denture base polymer (Palapress vario) was evaluated after water saturation and Stick glass fibre reinforcement. The data were analysed with ANOVA at a = 0.05. Water-storage caused a decrease in the flexural strength and stiffness of the materials (p > 0.05). Conventional denture base material with fibre reinforcement gave highest flexural strength (201.1 MPa) compared to fibre reinforced Eclipse (79.1 MPa) (p < 0.05). Water sorption after 76 days was 2.08% (Palapress vario) and 1.55% (Eclipse). Fibre-reinforcement of methylmethacrylate-free material was not as successful as conventional denture base and needs to be further optimized.

Effect of interfacial surface treatment on bond strength of particulate-filled composite to short fiber-reinforced composite.

Objective: The aim was to investigate the effect of different interfacial surface treatments on the shear bond strength (SBS) between a short fiber-reinforced flowable composite (SFRC) and a particulate-filled flowable composite (PFC). In addition, SBS between two successive layers of similar materials was evaluated. Materials and methods: One-hundred and forty-four specimens were prepared having either SFRC (everX Flow) as a substructure composite and PFC (G-aenial Flo X) as a surface composite or having one of the two materials as both substructure and surface layer. Eight groups of specimens were created (n = 18/per group) according to the interfacial surface protocol used. Group 1: no treatment; Group 2: ethanol one wipe; Group 3: ethanol three wipes; Group 4: phosphoric acid etching + bonding agent; Group 5: hydrofluoric acid etching + bonding agent; and Group 6: grinding + phosphoric acid etching. Group 7: only PFC layers and Group 8 (control) only SFRC layers without any surface treatment. After one-day storage (37 °C), SBS between surface and substructure composite layers was measured in a universal testing machine, and failure modes were visually analyzed. SEM was used to examine the bonding surface of the SFRC composite after surface treatment. SBS values were statistically analyzed with a one-way analysis of variance (ANOVA) followed by the Tukey HSD test (α = .05). Results: The SBS between successive SFRC layers (Group 8) was statistically (p < .05) the highest (43.7 MPa) among tested groups. Surface roughening by grinding followed by phosphoric acid etching (Group 6) resulted in a higher SBS (28.8 MPa) than the remaining surface treatments. Conclusion: Flowable composite with glass fibers (everX Flow) showed higher interlayer SBS compared to PFC flowable composite. Interfacial surface roughness increases the bonding of PFC to the substructure of SFRC.

Can Specular Gloss Measurements Predict the Effectiveness of Finishing/Polishing Protocols in Dental Polymers? A Systematic Review and Linear Mixed-effects Prediction Model.

PURPOSE: The current gold standard measure to assess polishing efficacy is surface roughness (SR) assessed in laboratory research. Specular gloss (SG) has been negatively correlated to SR, which raises the following question: Can SG be used to accurately determine the effectiveness of a finishing/polishing procedure in direct resin composites? METHODS: A systematic approach and search strategy, following Preferred Reporting Items for Systematic Reviews and Meta-analysis (PRISMA) guidelines, was developed and conducted in five electronic databases: PubMed/Medline, Scopus, Web of Science, EMBASE (Ovid), and SciELO/LILACS to identify laboratory studies that assessed SR and SG, simultaneously, of resin composites, without date or language restriction. Risk of bias assessment was carried out by two reviewers, independently. From the extracted quantitative data of SG/SR, regression analyses were performed, and a linear mixed-effects prediction model was derived using the nimble package in R (v4.0.3). RESULTS: A total of 928 potential studies were found, out of which, 13 were eligible after criterion screening. Experimental groups featured 31 resin composites of six different filler types, with the most common being microhybrids followed by nanohybrids. More than half of the studies initially reported a linear correlation between SR and SG, which ranged from r2 = 0.34-0.96. Taking into account the regression analysis and prediction model posteriorly performed, the corresponding SG threshold for 0.2 µm is estimated to be >55 GU. Most of the evidence was classified as moderate or high risk of bias. CONCLUSION: SG is universally correlated to SR in polymers, and a reference value of >55 GU is proposed, above which samples are considered well polished.