Phase synchronization of two anharmonic nanomechanical oscillators.

We investigate the synchronization of oscillators based on anharmonic nanoelectromechanical resonators. Our experimental implementation allows unprecedented observation and control of parameters governing the dynamics of synchronization. We find close quantitative agreement between experimental data and theory describing reactively coupled Duffing resonators with fully saturated feedback gain. In the synchronized state we demonstrate a significant reduction in the phase noise of the oscillators, which is key for sensor and clock applications. Our work establishes that oscillator networks constructed from nanomechanical resonators form an ideal laboratory to study synchronization--given their high-quality factors, small footprint, and ease of cointegration with modern electronic signal processing technologies.

Photothermal analysis of individual nanoparticulate samples using micromechanical resonators.

The ability to detect and analyze single sample entities such as single nanoparticles, viruses, spores, or molecules is of fundamental interest. This can provide insight into the individual specific properties which may differ from the statistical sample average. Here we introduce resonant photothermal spectroscopy, a novel method that enables the analysis of individual nanoparticulate samples. Absorption of light by an individual sample placed on a microstring resonator results in local heating of the string, which is reflected in its resonance frequency. The working principle of the spectrometer is demonstrated by analyzing the optical absorption of different micro- and nanoparticles on a microstring. We present the measurement of a simple absorption spectrum of multiple polystyrene microparticles illuminated with an unfocused LED light source. Using a diode laser, single 170 nm polystyrene nanoparticles are detected. With the current setup, nanoparticulate samples with a mass of ~40 ag are detectable. By using nanostrings, visible and infrared photothermal spectroscopy in the subattogram mass regime is possible and single molecule detection is within reach.

Compliant membranes improve resolution in full-wafer micro/nanostencil lithography.

This work reports on a considerable resolution improvement of micro/nanostencil lithography when applied on full-wafer scale by using compliant membranes to reduce gap-induced pattern blurring. Silicon nitride (SiN) membranes are mechanically decoupled from a rigid silicon (Si) frame by means of four compliant, protruding cantilevers. When pressing the stencil into contact with a surface to be patterned, the membranes thus adapt to the surface independently and reduce the gap between the membrane and the substrate even over large, uneven surfaces. Finite element modeling (FEM) simulations show that compliant membranes can deflect vertically 40 µm which is a typical maximal non-planarity observed in standard Si wafers, due to polishing. Microapertures in the stencil membrane are defined by UV lithography and nanoapertures, down to 200 nm in diameter, using focused ion beam (FIB). A thin aluminium (Al) layer is deposited through both compliant and non-compliant membranes on a Si wafer, for comparison. The blurring in the case of compliant membranes is up to 95% reduced on full-wafer scale compared to standard (non-compliant) membranes.

High-resolution resistless nanopatterning on polymer and flexible substrates for plasmonic biosensing using stencil masks.

The development of nanoscale lithographic methods on polymer materials is a key requirement to improve the spatial resolution and performance of flexible devices. Here, we report the fabrication of metallic nanostructures down to 20 and 50 nm in size on polymer materials such as polyimide, parylene, SU-8, and PDMS substrates without any resist processing using stencil lithography. Metallic nanodot array analysis of their localized surface plasmon spectra is included. We demonstrate plasmon resonance detection of biotin and streptavidin using a PDMS flexible film with gold nanodots. We also demonstrate the fabrication of metallic nanowires on polyimide substrates with their electrical characteristics showing an ohmic behavior. These results demonstrate high-resolution nanopatterning and device nanofabrication capability of stencil lithography on polymer and flexible substrates.

Metallic nanodot arrays by stencil lithography for plasmonic biosensing applications.

The fabrication of gold nanodots by stencil lithography and its application for optical biosensing based on localized surface plasmon resonance are presented. Arrays of 50-200 nm wide nanodots with different spacing of 50-300 nm are fabricated without any resist, etching, or lift-off process. The dimensions and morphology of the nanodots were characterized by scanning electron and atomic force microscopy. The fabricated nanodots showed localized surface plasmon resonance in their extinction spectra in the visible range. The resonance wavelength depends on the periodicity and dimensions of the nanodots. Bulk refractive index measurements and model biosensing of streptavidin were successfully performed based on the plasmon resonance shift induced by local refractive index change when biomolecules are adsorbed on the nanodots. These results demonstrate the potential of stencil lithography for the realization of plasmon-based biosensing devices.