RESUMO
The development of high-efficiency organic solar cells (OSCs) processed from non-halogenated solvents is crucially important for their scale-up industry production. However, owing to the difficulty of regulating molecular aggregation, there is a huge efficiency gap between non-halogenated and halogenated solvent processed OSCs. Herein, we fabricate o-xylene processed OSCs with approaching 20 % efficiency by incorporating a trimeric guest acceptor named Tri-V into the PM6:L8-BO-X host blend. The incorporation of Tri-V effectively restricts the excessive aggregation of L8-BO-X, regulates the molecular packing and optimizes the phase-separation morphology, which leads to mitigated trap density states, reduced energy loss and suppressed charge recombination. Consequently, the PM6:L8-BO-X:Tri-V-based device achieves an efficiency of 19.82 %, representing the highest efficiency for non-halogenated solvent-processed OSCs reported to date. Noticeably, with the addition of Tri-V, the ternary device shows an improved photostability than binary PM6:L8-BO-X-based device, and maintains 80 % of the initial efficiency after continuous illumination for 1380â h. This work provides a feasible approach for fabricating high-efficiency, stable, eco-friendly OSCs, and sheds new light on the large-scale industrial production of OSCs.
RESUMO
Ternary polymer solar cells(PSCs) have been identified as an effective approach to improving power conversion efficiency (PCE) of binary PSCs. However, most of the third component, especially Y-series non-fullerene acceptors, is a fused ring acceptor which often requires a rather tedious synthesis and the use of hazardous organostannane reagents. In this work, two nonfused ring acceptors IOEH-4F and IOEH-N2F are synthesized by a green synthetic route and incorporated into PM6:Y6 blend. Encouragingly, the IOEH-4F and IOEH-N2F-based ternary PSCs exhibited more efficient charge transfer, exciton separation, and lower energy loss than PM6:Y6-based PSCs. And the IOEH-4F and IOEH-N2F-based ternary PSCs achieved an impressive PCE of 17.80% and 18.13%, respectively, which are higher than that of PM6:Y6 based PSCs (16.18%). Notably, these PCE values are also the highest PCEs for ternary PSCs including non-fused ring acceptors. Importantly, even when the IOEH-N2F:Y6 ratios increased from 0.05:1.2 to 0.50:1.2, the PCE of IOEH-N2F-based ternary PSCs (16.70%) are still higher than that of PM6:Y6 based PSCs, indicating the great potential for cost saving. It is believed that the findings will help the design of better nonfused ring acceptors and the optimization of corresponding ternary PSCs with cost-saving advantage.
RESUMO
Double-fibril network morphology (DFNM), in which the donor and the acceptor can self-assemble into a double-fibril structure, is beneficial for exciton dissociation and charge transport in organic solar cells. Herein, it is demonstrated that such DFNM can be constructed and optimized in all-polymer solar cells (all-PSCs) with the assistance of 2-alkoxynaphthalene volatile solid additives. It is revealed that the incorporation of 2-alkoxynaphthalene can induce a stepwise regulation in the aggregation of donor and acceptor molecules during film casting and thermal annealing processes. Through altering the alkoxy of 2-alkoxynaphthalene solid additives, both the intermolecular interactions and molecular miscibility with the host materials can be precisely tuned, which allows for the optimization of the molecular aggregation process and facilitation of molecular self-assembly, and thus leading to reinforced molecular packing and optimized DFNM. As a result, an unprecedented efficiency of 19.50% (certified as 19.1%) is obtained for 2-ethoxynaphthalene-processed PM6:PY-DT-X all-PSCs with excellent photostability (T80 = 1750 h). This work reveals that the optimization of DFNM via solid additive strategy is a promising avenue to boosting the performance of all-PSCs.
RESUMO
The energy loss induced open-circuit voltage (VOC) deficit hampers the rapid development of state-of-the-art organic solar cells (OSCs), therefore, it is extremely urgent to explore effective strategies to address this issue. Herein, a new volatile solid additive 1,4-bis(iodomethyl)cyclohexane (DIMCH) featured with concentrated electrostatic potential distribution is utilized to act as a morphology-directing guest to reduce energy loss in multiple state-of-art blend system, leading to one of highest efficiency (18.8%) at the forefront of reported binary OSCs. Volatile DIMCH decreases radiative/non-radiative recombination induced energy loss (ΔE2/ΔE3) by rationally balancing the crystallinity of donors and acceptors and realizing homogeneous network structure of crystal domain with reduced D-A phase separation during the film formation process and weakens energy disorder and trap density in OSCs. It is believed that this study brings not only a profound understanding of emerging volatile solid additives but also a new hope to further reduce energy loss and improve the performance of OSCs.
RESUMO
Morphology control is crucial in achieving high-performance organic solar cells (OSCs) and remains a major challenge in the field of OSC. Solid additive is an effective strategy to fine-tune morphology, however, the mechanism underlying isomeric solid additives on blend morphology and OSC performance is still vague and urgently requires further investigation. Herein, two solid additives based on pyridazine or pyrimidine as core units, M1 and M2, are designed and synthesized to explore working mechanism of the isomeric solid additives in OSCs. The smaller steric hindrance and larger dipole moment facilitate better π-π stacking and aggregation in M1-based active layer. The M1-treated all-small-molecule OSCs (ASM OSCs) obtain an impressive efficiency of 17.57%, ranking among the highest values for binary ASM OSCs, with 16.70% for M2-treated counterparts. Moreover, it is imperative to investigate whether the isomerization engineering of solid additives works in state-of-the-art polymer OSCs. M1-treated D18-Cl:PM6:L8-BO-based devices achieve an exceptional efficiency of 19.70% (certified as 19.34%), among the highest values for OSCs. The work provides deep insights into the design of solid additives and clarifies the potential working mechanism for optimizing the morphology and device performance through isomerization engineering of solid additives.
RESUMO
Single perylene diimide (PDI) used as a non-fullerene acceptor (NFA) in organic solar cells (OSCs) is enticing because of its low cost and excellent stability. To improve the photovoltaic performance, it is vital to narrow the bandgap and regulate the stacking behavior. To address this challenge, we synthesize soluble perylenetetracarboxylic bisbenzimidazole (PTCBI) molecules with a bulky side chain at the bay region, by replacing the widely used "swallow tail" type alkyl chains at the imide position of PDI molecules with a planar benzimidazole structure. Compared with PDI molecules, PTCBI molecules exhibit red-shifted UV-vis absorption spectra with larger extinction coefficient, and one magnitude higher electron mobility. Finally, OSCs based on one soluble PTCBI-type NFA, namely MAS-7, exhibit a champion power conversion efficiency (PCE) of 4.34%, which is significantly higher than that of the corresponding PDI-based OSCs and is the highest PCE of PTCBI-based OSCs reported. These results highlight the potential of soluble PTCBI derivatives as NFAs in OSCs.
RESUMO
Hybrid cycloalkyl-alkyl side chains are considered a unique composite side-chain system for the construction of novel organic semiconductor materials. However, there is a lack of fundamental understanding of the variations in the single-crystal structures as well as the optoelectronic and energetic properties generated by the introduction of hybrid side chains in electron acceptors. Herein, symmetric/asymmetric acceptors (Y-C10ch and A-C10ch) bearing bilateral and unilateral 10-cyclohexyldecyl are designed, synthesized, and compared with the symmetric acceptor 2,2'-((2Z,2'Z)-((12,13-bis(2-butyloctyl)-3,9 bis(ethylhexyl)-12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2â³,3â³':4',5']thieno[2',3':4,5] pyrrolo[3,2-g]thieno[2',3':4,5]thieno[3,2-b]indole-2,10- diyl)bis(methanylylidene))bis(5,6-difluoro-3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile (L8-BO). The stepwise introduction of 10-cyclohexyldecyl side chains decreases the optical bandgap, deepens the energy level, and enables the acceptor molecules to pack closely in a regular manner. Crystallographic analysis demonstrates that the 10-cyclohexyldecyl chain endows the acceptor with a more planar skeleton and enforces more compact 3D network packing, resulting in an active layer with higher domain purity. Moreover, the 10-cyclohexyldecyl chain affects the donor/acceptor interfacial energetics and accelerates exciton dissociation, enabling a power conversion efficiency (PCE) of >18% in the 2,2'-((2Z,2'Z)-((12,13-bis(2-ethylhexyl)-3,9-diundecyl12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2â³,3â³':4',5']thieno[2',3':4,5]pyrrolo[3,2-g]thieno[2',3':4,5]thieno[3,2-b]indole-2,10-diyl)bis(methanylylidene))bis(5,6-difluoro-3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile (Y6) (PM6):A-C10ch-based organic solar cells (OSCs). Importantly, the incorporation of Y-C10ch as the third component of the PM6:L8-BO blend results in a higher PCE of 19.1%. The superior molecular packing behavior of the 10-cyclohexyldecyl side chain is highlighted here for the fabrication of high-performance OSCs.
RESUMO
Regulation of the exciton generation, diffusion, and carrier transport, as well as optimization of the non-radiative energy loss could further overcome the power conversion efficiency limitation of organic solar cells. However, the relationship between exciton properties and non-radiative energy loss has seldom been investigated. Herein, taking D18-series devices as the research model, the exciton diffusion length (LD) and hole transfer dynamics can be remarkably improved by the variation of electron-withdrawing halogen and the non-radiative energy loss simultaneously can be suppressed. By combining the analysis results of hole transfer, exciton diffusion, charge separation, and recombination, this work demonstrates that the photo-induced exciton in the chlorinated polymer donor can diffuse to a longer distance within the effective exciton lifetime, suppress the exciton recombination, and enhance device performance. The results define the relationship between the exciton behaviors and non-radiative energy loss and further reveal the significance of controlling the bulk heterojunction with superior photo-physical properties.
RESUMO
PURPOSE: To observe and analyze the clinical and multi-mode imaging features of eyes with PHOMS, and to introduce two cases of PHOMS which underwent multi-mode imaging. METHODS: Retrospective clinical observational study. A total of 26 patients (37 eyes) with hyperreflective structures surrounded by hyporeflective edges around the optic discs who were examined and diagnosed at Shandong Eye Hospital between January 2019 and June 2021 were included in the study. Among these patients, 12 were male and 14 were female. Fifteen were monocular. The average age was 39 years. All patients underwent the following examinations: Best-corrected visual acuity (BCVA), intraocular pressure examinations, slit-lamp anterior segment examinations, indirect ophthalmoscopy, visual field examinations, fundus color photography, fundus autofluorescence (FAF), optical coherence tomography (OCT), and optical coherence tomography angiography (OCTA). Some of the patients were examined with fundus fluorescein angiography (FFA). Clinical data and imaging characteristics from the OCT, OCTA, and FFA were analyzed retrospectively. RESULTS: We found the hyperreflective structures surrounded by hyporeflective edges around the optic discs in 37 eyes. EDI-OCT results revealed hyperreflective structures surrounded by hyporeflective edges around the optic discs in all eyes. Typical hyperreflexia lesions occurred around the optic disc, located subretinally and above Bruch's membrane. OCTA revealed that the highly reflective perioptic material also had vascular structures. CONCLUSION: EDI-OCT of PHOMS showed hyperreflective structures surrounded by hyporeflective edges around all of the optic discs. Infra-red photography showed temporal hyperreflexia. These characteristics can be seen in a variety of diseases and may be a relatively common feature revealed by EDI-OCT scanning. These characteristics may also be seen in elderly patients as well as children. PHOMS may be found in optic disc drusen (ODD), tilted disc syndrome (TDS), optic neuritis, ischemic optic neuropathy, and in white dot syndromes. Few patients may be developed into macular neovascularization (MNV). In order to improve the accuracy and robustness of the conclusions and provide better clinical guidance, we need to conduct more comprehensive research in the subsequent clinical work.
RESUMO
In order to obtain high-performance all-small-molecule organic solar cells (ASM-OSCs), it is crucial to exploit the available strategy for molecular design and to further understand key structure-property relationship that can rationally control the blend nanomorphology and influence the physical process. In this work, we design two small molecule donors FBD-S1 and TBD-S2 with identical electron-withdrawing units but various asymmetric central cores, which exhibit differing phase separation in Y6-based blend films. It is found that TBD-S2 with increased phase separation between donor and acceptor can lead to more favorable interpenetrating networks, effective exciton dissociation, and enhanced and more balanced charge transport. Importantly, a remarkable PCE of 13.1% is obtained for TBD-S2:Y6 based ASM-OSCs, which is an attractive photovoltaic performance for ASM-OSCs. This result demonstrates that the central core modification at the atomic level for small molecule donors can delicately control the phase separation and optimize photophysical processes, and refines device performance, which facilitate development in the ASM-OSC research field.
RESUMO
Secondary doping has a long history of use in conductivity enhancement in poly(3,4-ethylenedioxythiophene) : poly(styrene sulfonate) (PEDOT : PSS). However, very little research has addressed its detrimental effect on application performance of PEDOT : PSS in organic solar cells. Herein, it was shown that the uneven drying of secondary dopant-water mixture results in a nonuniform/continuous film structure, causing severe damage to the device efficiencies (dropping about 8 and 23 % for poly[(2,6-(4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)-benzo[1,2-b:4,5-b']dithiophene))-alt-(5,5-(1',3'-di-2-thienyl-5',7'-bis(2-ethylhexyl)benzo[1',2'-c:4',5'-c']dithiophene-4,8-dione))] (PBDB-T) : 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b']dithiophene (ITIC) and poly[(2,6-(4,8-bis(5-(2-ethylhexyl)-4-fluorothiophen-2-yl)benzo[1,2-b:4,5-b']dithio-phene))-co-(1,3-di(5-thiophene-2-yl)-5,7-bis(2-ethylhexyl)-benzo[1,2-c:4,5-c']dithiophene-4,8-dione))](PM6) : (3,9-bis(1-oxo-2-methylene-3-(1,1-dicyanomethylene)-5,6-difluoroindanone)-5,5,11,11-tetrakis(4-n-hexylphenyl)-dithieno[2,3d:2',3'd']-s-indaceno[1,2b:5,6b']dithiophene (IT-4F) cells, respectively) and thermal stabilities. Moreover, a simple yet robust dialysis treatment was proposed to solve the issue of noncontinuity and retain the secondary doping's advantages of quinoid structure simultaneously, thus demonstrating a significant enhancement in device performance. This study will be of great importance to the future exploration of the next generation of post-treatment strategy.
RESUMO
Two random conjugated polymers (CPs), namely, PIDTT-TBT and PIDTT-TFBT, in which indacenodithieno[3,2-b]thiophene (IDTT), 3-octylthiophene, and benzothiadiazole (BT) were in turn utilized as electron-donor (D), π-bridge, and electron-acceptor (A) units, were synthesized to comprehensively analyze the impact of reducing thiophene π-bridge and further fluorination on photostability and photovoltaic performance. Meanwhile, the control polymer PIDTT-DTBT with alternating structure was also prepared for comparison. The broadened and enhanced absorption, down-shifted highest occupied molecular orbital energy level (EHOMO), more planar molecular geometry thus enhanced the aggregation in the film state, but insignificant impact on aggregation in solution and photostability were found after both reducing thiophene π-bridge in PIDTT-TBT and further fluorination in PIDTT-TFBT. Consequently, PIDTT-TBT-based device showed 185% increased PCE of 5.84% profited by synergistically elevated VOC, JSC, and FF than those of its counterpart PIDTT-DTBT, and this improvement was chiefly ascribed to the improved absorption, deepened EHOMO, raised µh and more balanced µh/µe, and optimized morphology of photoactive layer. However, the dropped PCE was observed after further fluorination in PIDTT-TFBT, which was mainly restricted by undesired morphology for photoactive layer as a result of strong aggregation even if in the condition of the upshifted VOC. Our preliminary results can demonstrate that modulating the π-bridge in polymer backbone was an effective method with the aim to enhance the performance for solar cell.
RESUMO
Ternary strategy is a promising approach to broaden the photoresponse of polymer solar cells (PSCs) by adopting combinatory photoactive blends. However, it could lead to a more complicated situation in manipulating the bulk morphology. Achieving an ideal morphology that enhances the charge transport and light absorption simultaneously is an essential avenue to promote the device performance. Herein, two polymers with different lengths of side groups (P1 is based on phenyl side group and P2 is based on biphenyl side group) are adopted in the dual-acceptor ternary systems to evaluate the relationship between conjugated side group and crystalline behavior in the ternary system. The P1 ternary system delivers a greatly improved power conversion efficiency (PCE) of 13.06%, which could be attributed to the intense and broad photoresponse and improved charge transport originating from the improved crystallinity. Inversely, the P2 ternary device only exhibits a poor PCE of 8.97%, where the decreased device performance could mainly be ascribed to the disturbed molecular stacking of the components originating from the overlong conjugated side group. The results demonstrate a conjugated side group could greatly determine the device performance by tuning the crystallinity of components in ternary systems.
RESUMO
In this work, a random terpolymer methodology combining two electron-rich units, asymmetric thienobenzodithiophene (TBD) and thieno[2,3-f]benzofuran segments, is systematically investigated. The synergetic effect is embodied on the molecular packing and nanophase when copolymerized with 1,3-bis(2-ethylhexyl)benzo[1,2-c:4,5-c']dithiophene-4,8-dione, producing an impressive power conversion efficiency (PCE) of 14.2% in IT-4F-based NF-PSCs, which outperformed the corresponding D-A copolymers. The balanced aggregation and better interpenetrating network of the TBD50:IT-4F blend film can lead to mixing region exciton splitting and suppress carrier recombination, along with high yields of long-lived carriers. Moreover, the broad applicability of terpolymer methodology is successfully validated in most electron-deficient systems. Especially, the TBD50/Y6-based device exhibits a high PCE of 15.0% with a small energy loss (0.52 eV) enabled by the low nonradiative energy loss (0.22 eV), which are among the best values reported for polymers without using benzodithiophene unit to date. These results demonstrate an outstanding terpolymer approach with backbone engineering to raise the hope of achieving even higher PCEs and to enrich organic photovoltaic materials reservoir.
RESUMO
The D-π-A conjugated polymers with a benzotriazole (BTz) unit as the A moiety have been intensively investigated as donor materials in nonfullerene solar cells. However, these BTz even the fluorinated-BTz constructed D-π-A polymers mostly suffered from upward highest occupied molecular orbital (HOMO) energy levels, leading to inferior open-circuit voltage (VOC) and efficiencies in the fabricated solar cells. Herein, we explored a new approach in response to this issue via the strategy of π-bridge fusion to A moiety. As a result, the medium band gap D-π-A polymer PY2 was evolved into wide band gap D-A polymer PY1 with fused-DTBTz as the new A moiety, accompanied with a greatly declined HOMO energy level by 0.26 eV, a remarkable blue-shifted absorption onset by about 51 nm, and concurrently moderately enhanced face-on stacking orientations in neat polymer and donor/acceptor blend films. The synergetic optimizations in energy level, absorption characteristic and molecular stacking feature via the π-bridge fusion design witness an all-round improvement in photovoltaic parameters including the focused VOC, short-circuit current density (JSC), and fill factor (FF), with narrow band gap ITIC as the acceptor material. Specifically, the PY1-based solar cells produce an optimal power conversion efficiency (PCE) of 12.49%, with superior VOC of 0.94 V, JSC of 18.46 mA cm-2, and FF of 0.72, significantly surpassing those of PY2-based optimal device with a PCE of 7.39%, VOC of 0.77 V, JSC of 14.54 mA cm-2, and FF of 0.66 and even the reported classical fluorinated-BTz based polymer J51 (VOC of 0.82 V, PCE of 9.26%). Promisingly, there is a huge room for improvement in photovoltaic properties with rational fluorination or chlorination of the fused-DTBTz unit or the D moiety of the D-A polymers.
RESUMO
Side chain engineering has been an effective approach to modulate the solution processability, optoelectronic properties and miscibility of conjugated polymers (CPs) for organic/polymeric photovoltaic cells (PVCs). As compared with the most commonly used method of introducing alkyl chains, the employment of alkyl-substituted aryl flanks would provide two-dimensional (2-D) CPs having solution processability alongside additional merits like deepened highest occupied molecular orbital (HOMO) energy levels, increased absorption coefficient and charger transporting, etc. In this paper, the triple C≡C bond was used as conjugated linker to decrease the steric hindrance between the flanks of 4,5-didecylthien-2-yl (T) and dithieno[2,3-d:2',3'-d']benzo[1,2-b:4,5-b']dithiophene (DTBDT) core. In addition, an alternating CP derived from 4,5-didecylthien-2-yl-ethynyl (TE) flanked DTBDT, and 4,9-bis(4-octylthien-2-yl) naphtho[1,2-c:5,6-c']bis[1,2,5]thiadiazole (DTNT), named as PDTBDT-TE-DTNT, was synthesized and characterized. As compared with the controlled PDTBDT-T-DTNT, which was derived from 4,5-didecylthien-2-yl flanked DTBDT and DTNT, the results for exciton dissociation probability, density functional theory (DFT), time-resolved photoluminescence (PL) measurements, etc., revealed that the lower steric hindrance between TE and DTBDT might lead to the easier rotation of the TE flanks, thus contributing to the decrease of the exciton lifetime and dissociation probability, finally suppressing the short-circuit current density (JSC), etc., of the photovoltaic devices from PDTBDT-TE-DTNT.
RESUMO
The asymmetric thienobenzodithiophene (TBD) structure is first systematically compared with the benzo[1,2-b:4,5-b']dithiophene (BDT) and dithieno[2,3-d:2',3'-d']benzo[1,2-b:4,5-b']dithiophene (DTBDT) units in donor-acceptor (D-A) copolymers and applied as the central core in small molecule acceptors (SMAs). Specific polymers including PBDT-BZ, PTBD-BZ, and PDTBDT-BZ with different macromolecular conformations are synthesized and then matched with four elaborately designed acceptor-donor-acceptor (A-D-A) SMAs with structures comparable to their donor counterparts. The resulting polymer solar cell performance trends are dramatically different from each other and highly material-dependent, and the active layer morphology is largely governed by polymer conformation. Because of its more linear backbone, the PTBD-BZ film has higher crystallinity and more ordered and denser π-π stacking than those of the PBDT-BZ and PDTBDT-BZ films. Thus, PTBD-BZ shows excellent compatibility with and strong independence on the SMAs with varied structures, and PTBD-BZ-based cells deliver high power conversion efficiency (PCE) of 10-12.5%, whereas low PCE is obtained by cells based on PDTBDT-BZ because of its zigzag conformation. Overall, this study reveals control of molecular conformation as a useful approach to modulate the photovoltaic properties of conjugated polymers.
RESUMO
Two new low bandgap conjugated polymers, PBDTS-ID and PBDTS-DTNT, containing isoindigo (ID) and naphtho[1,2-c:5,6-c']bis[1,2,5]thiadiazole (NT), respectively, as an electron-deficient unit and alkylthiothienyl-substituted benzodithiophene (BDTS) as an electron-rich unit, were designed and synthesized by palladium-catalyzed Stille polycondensation. Both polymers showed good thermal stability up to 330 °C and broad absorption ranging from 300 to 842 nm. Electrochemical measurement revealed that PBDTS-ID and PBDTS-DTNT exhibited relatively low-lying highest occupied molecular orbital energy levels at -5.40 and -5.24 eV, respectively. These features might be beneficial for obtaining reasonable high open-circuit voltage and high short-circuit current. Polymer solar cells (PSCs) were fabricated with an inverted structure of indium-tin oxide/poly(ethylenimine ethoxylate)/polymer:PC71BM/MoO3/Ag. As a preliminary result, the PSCs based on PBDTS-ID and PBDTS-DTNT exhibited moderate power conversion efficiencies of 2.70% and 2.71%, respectively.
RESUMO
Three alternated D-π-A type 5,10-bis(triisopropylsilylethynyl)dithieno[2,3-d:2',3'-d']-benzo[1,2-b:4,5-b']dithiophene (DTBDT-TIPS)-based semiconducting conjugated copolymers (CPs), PDTBDT-TIPS-DTBT-OD, PDTBDT-TIPS-DTFBT-OD, and PDTBDT-TIPS-DTNT-OD, bearing different A units, including benzothiadiazole (BT), 5,6-difluorinated-BT (FBT) and naphtho[1,2-c:5,6-c']-bis[1,2,5]thiadiazole (NT), were designed and synthesized to investigate the impact of the variation in electron-deficient units on the properties of these photovoltaic polymers. It was exhibited that the down-shifted highest occupied molecular orbital energy level (EHOMO), the enhanced aggregation in both the chlorobenzene solution and the solid film, as well as the better molecular planarity, were achieved using methods involving fluorination and the replacement of BT with NT on the polymer backbone. The absorption profile was little changed upon fluorination; however, it was greatly broadened during replacement of BT with NT. Consequently, the optimized photovoltaic device based on the PDTBDT-TIPS-DTNT-OD exhibited synchronous enhancements in the open-circuit voltage (VOC) of 0.88 V, the short-circuit current density (JSC) of 7.21 mA cm-2, and the fill factor (FF) of 52.99%, resulting in a drastic elevation in the PCE by 129% to 3.37% compared to that of the PDTBDT-TIPS-DTBT-OD. This was triggered by PDTBDT-TIPS-DTNT-OD's broadened absorption, deepened EHOMO, improved coplanarity, and enhanced SCLC mobility (which increased 3.9 times), as well as a favorable morphology of the active layer. Unfortunately, the corresponding PCE deteriorated after incorporating fluorine into the BT, due to the oversized aggregation and large phase separation morphology in the blend films, severely impairing its JSC. Our preliminary results demonstrated that the replacement of BT with NT in a D-π-A type polymer backbone was an effective strategy of tuning the molecular structure to achieve highly efficient polymer solar cells (PSCs).