High Thermoelectric Performance in Rhombohedral GeSe-LiBiTe2.

GeSe, an analogue of SnSe, shows promise in exhibiting exceptional thermoelectric performance in the Pnma phase. The constraints on its dopability, however, pose challenges in attaining optimal carrier concentrations and improving ZT values. This study demonstrates a crystal structure evolution strategy for achieving highly doped samples and promising ZTs in GeSe via LiBiTe2 alloying. A rhombohedral phase (R3m) can be stabilized in the GeSe-LiBiTe2 system, further evolving into a cubic (Fm3̅m) phase with a rising temperature. The band structures of GeSe-LiBiTe2 in the rhombohedral and cubic phases feature a similar multiple-valley energy-converged valence band of L and Σ bands. The observed high carrier concentration (∼1020 cm-3) reflects the effective convergence of these bands, enabling a high density-of-states effective mass and an enhanced power factor. Moreover, a very low lattice thermal conductivity of 0.6-0.5 W m-1 K-1 from 300 to 723 K is achieved in 0.9GeSe-0.1LiBiTe2, approaching the amorphous limit value. This remarkably low lattice thermal conductivity is related to phonon scattering from point defects, planar vacancies, and ferroelectric instability-induced low-energy Einstein oscillators. Finally, a maximum ZT value of 1.1 to 1.3 at 723 K is obtained, with a high average ZT value of over 0.8 (400-723 K) in 0.9GeSe-0.1LiBiTe2 samples. This study establishes a viable route for tailoring crystal structures to significantly improve the performance of GeSe-related compounds.

Implications and Optimization of Domain Structures in IV-VI High-Entropy Thermoelectric Materials.

High-entropy semiconductors are now an important class of materials widely investigated for thermoelectric applications. Understanding the impact of chemical and structural heterogeneity on transport properties in these compositionally complex systems is essential for thermoelectric design. In this work, we uncover the polar domain structures in the high-entropy PbGeSnSe1.5Te1.5 system and assess their impact on thermoelectric properties. We found that polar domains induced by crystal symmetry breaking give rise to well-structured alternating strain fields. These fields effectively disrupt phonon propagation and suppress the thermal conductivity. We demonstrate that the polar domain structures can be modulated by tuning crystal symmetry through entropy engineering in PbGeSnAgxSbxSe1.5+xTe1.5+x. Incremental increases in the entropy enhance the crystal symmetry of the system, which suppresses domain formation and loses its efficacy in suppressing phonon propagation. As a result, the room-temperature lattice thermal conductivity increases from κL = 0.63 Wm-1 K-1 (x = 0) to 0.79 Wm-1 K-1 (x = 0.10). In the meantime, the increase in crystal symmetry, however, leads to enhanced valley degeneracy and improves the weighted mobility from µw = 29.6 cm2 V-1 s-1 (x = 0) to 35.8 cm2 V-1 s-1 (x = 0.10). As such, optimal thermoelectric performance can be achieved through entropy engineering by balancing weighted mobility and lattice thermal conductivity. This work, for the first time, studies the impact of polar domain structures on thermoelectric properties, and the developed understanding of the intricate interplay between crystal symmetry, polar domains, and transport properties, along with the impact of entropy control, provides valuable insights into designing GeTe-based high-entropy thermoelectrics.

High Carrier Mobility and Promising Thermoelectric Module Performance of N-Type PbSe Crystals.

The scarcity of Te hampers the widespread use of Bi2Te3-based thermoelectric modules. Here, the thermoelectric module potential of PbSe is investigated by improving its carrier mobility. Initially, large PbSe crystals are grown with the temperature gradient method to mitigate grain boundary effects on carrier transport. Subsequently, light doping with <1mole‰ halogens (Cl/Br/I) increases room-temperature carrier mobility to ~1600 cm2 V-1 s-1, achieved by reducing carrier concentration compared to traditional heavy doping. Crystal growth design and light doping enhance carrier mobility without affecting effective mass, resulting in a high power factor ~40 µW cm-1 K-2 in PbSe-Cl/Br/I crystals at 300 K. Additionally, Cl/Br/I doping reduces thermal conductivity and bipolar diffusion, leading to significantly lower thermal conductivity at high temperature. Enhanced carrier mobility and suppressed bipolar effect boost ZT values across the entire temperature range in n-type PbSe-Cl/Br/I crystals. Specifically, ZT values of PbSe-Br crystal reach ~0.6 at 300 K, ~1.2 at 773 K, and the average ZT (ZTave) reaches ~1.0 at 300-773 K. Ultimately, ~5.8% power generation efficiency in a PbSe single leg with a maximum temperature cooling difference of 40 K with 7-pair modules is achieved. These results indicate the potential for cost-effective and high-performance thermoelectric cooling modules based on PbSe.

Network Pharmacology Analysis of Liquid-Cultured Armillaria ostoyae Mycelial Metabolites and Their Molecular Mechanism of Action against Gastric Cancer.

Armillaria sp. are traditional edible medicinal mushrooms with various health functions; however, the relationship between their composition and efficacy has not yet been determined. Here, the ethanol extract of liquid-cultured Armillaria ostoyae mycelia (AOME), a pure wild Armillaria sp. strain, was analyzed using UHPLC-QTOF/MS, network pharmacology, and molecular docking techniques. The obtained extract affects various metabolic pathways, such as JAK/STAT and PI3K/AKT. The extract also contains important compounds such as 4-(dimethylamino)-N-[7-(hydroxyamino)-7-oxoheptyl] benzamide, isoliquiritigenin, and 7-hydroxycoumarin. Moreover, the extract targets key proteins, including EGFR, SCR, and IL6, to suppress the progression of gastric cancer, thereby synergistically inhibiting cancer development. The molecular docking analyses indicated that the main compounds stably bind to the target proteins. The final cell culture experimental data showed that the ethanol extract inhibited MGC-803 gastric cancer cells. In summary, our research revealed the beneficial components of AOME for treating gastric cancer and its associated molecular pathways. However, further research is needed to confirm its effectiveness and safety in gastric cancer patients.

Silver Atom Off-Centering in Diamondoid Solid Solutions Causes Crystallographic Distortion and Suppresses Lattice Thermal Conductivity.

The class I-III-VI2 diamondoid compounds with tetrahedral bonding are important semiconductors widely applied in optoelectronics. Understanding their heat transport properties and developing an effective method to predict the diamondoid solid solutions' thermal conductivity will help assess their impact as thermoelectrics. In this work, we investigated in detail the heat transport properties of CuGa1-xInxTe2 and Cu1-xAgxGaTe2 and found that in the Ag-alloyed solid solutions, the Ag atom off-centering effect results in crystallographic distortion and extra strong acoustic-optical phonon scattering and an extremely low lattice thermal conductivity. Moreover, we integrate the alloy scattering and the off-centering effect with the crystallographic distortion parameter to develop a modified Klemens model that predicts the thermal conductivity of diamondoid solid solutions. Finally, we demonstrate that Cu1-xAgxGaTe2 solid solutions are promising p-type thermoelectric materials, with a maximum ZT of 1.23 at 850 K for Cu0.58Ag0.4GaTe2.

Unraveling the Role of Entropy in Thermoelectrics: Entropy-Stabilized Quintuple Rock Salt PbGeSnCdxTe3+x.

Entropy-engineered materials are garnering considerable attention owing to their excellent mechanical and transport properties, such as their high thermoelectric performance. However, understanding the effect of entropy on thermoelectrics remains a challenge. In this study, we used the PbGeSnCdxTe3+x family as a model system to systematically investigate the impact of entropy engineering on its crystal structure, microstructure evolution, and transport behavior. We observed that PbGeSnTe3 crystallizes in a rhombohedral structure at room temperature with complex domain structures and transforms into a high-temperature cubic structure at ∼373 K. By alloying CdTe with PbGeSnTe3, the increased configurational entropy lowers the phase-transition temperature and stabilizes PbGeSnCdxTe3+x in the cubic structure at room temperature, and the domain structures vanish accordingly. The high-entropy effect results in increased atomic disorder and consequently a low lattice thermal conductivity of 0.76 W m-1 K-1 in the material owing to enhanced phonon scattering. Notably, the increased crystal symmetry is conducive to band convergence, which results in a high-power factor of 22.4 µW cm-1 K-1. As a collective consequence of these factors, a maximum ZT of 1.63 at 875 K and an average ZT of 1.02 in the temperature range of 300-875 K were obtained for PbGeSnCd0.08Te3.08. This study highlights that the high-entropy effect can induce a complex microstructure and band structure evolution in materials, which offers a new route for the search for high-performance thermoelectrics in entropy-engineered materials.

High Thermoelectric Performance in Chalcopyrite Cu1-xAgxGaTe2-ZnTe: Nontrivial Band Structure and Dynamic Doping Effect.

The understanding of thermoelectric properties of ternary I-III-VI2 type (I = Cu, Ag; III = Ga, In; and VI = Te) chalcopyrites is less well developed. Although their thermal transport properties are relatively well studied, the relationship between the electronic band structure and charge transport properties of chalcopyrites has been rarely discussed. In this study, we reveal the unusual electronic band structure and the dynamic doping effect that could underpin the promising thermoelectric properties of Cu1-xAgxGaTe2 compounds. Density functional theory (DFT) calculations and electronic transport measurements suggest that the Cu1-xAgxGaTe2 compounds possess an unusual non-parabolic band structure, which is important for obtaining a high Seebeck coefficient. Moreover, a mid-gap impurity level was also observed in Cu1-xAgxGaTe2, which leads to a strong temperature-dependent carrier concentration and is able to regulate the carrier density at the optimized value for a wide temperature region and thus is beneficial to obtaining the high power factor and high average ZT of Cu1-xAgxGaTe2 compounds. We also demonstrate a great improvement in the thermoelectric performance of Cu1-xAgxGaTe2 by introducing Cu vacancies and ZnTe alloying. The Cu vacancies are effective in increasing the hole density and the electrical conductivity, while ZnTe alloying reduces the thermal conductivity. As a result, a maximum ZT of 1.43 at 850 K and a record-high average ZT of 0.81 for the Cu0.68Ag0.3GaTe2-0.5%ZnTe compound are achieved.

Low Thermal Conductivity in Heteroanionic Materials with Layers of Homoleptic Polyhedra.

Although BiAgOSe, an analogue of a well-studied thermoelectric material BiCuOSe, is thermodynamically stable, its synthesis is complicated by the low driving force of formation from the stable binary and ternary intermediates. Here we have developed a "subtraction strategy" to suppress byproducts and produce pure phase BiAgOSe using hydrothermal methods. Electronic structure calculations and optical characterization show that BiAgOSe is an indirect bandgap semiconductor with a bandgap of 0.95 eV. The prepared sample exhibits lower lattice thermal conductivities (0.61 W·m-1·K-1 at room temperature and 0.35 W·m-1·K-1 at 650 K) than BiCuOSe. Lattice dynamical simulations and variable temperature diffraction measurements demonstrate that the low lattice thermal conductivity arises from both the low sound velocity and high phonon-phonon scattering rates in BiAgOSe. These in turn result primarily from the soft Ag-Se bonds in the edge-sharing AgSe4 tetrahedra and large sublattice mismatch between the quasi-two-dimensional [Bi2O2]2+ and [Ag2Se2]2- layers. These results highlight the advantages of manipulating the chemistry of homoleptic polyhedra in heteroanionic compounds for electronic structure and phonon transport control.

Valence Disproportionation of GeS in the PbS Matrix Forms Pb5Ge5S12 Inclusions with Conduction Band Alignment Leading to High n-Type Thermoelectric Performance.

Converting waste heat into useful electricity using solid-state thermoelectrics has a potential for enormous global energy savings. Lead chalcogenides are among the most prominent thermoelectric materials, whose performance decreases with an increase in chalcogen amounts (e.g., PbTe > PbSe > PbS). Herein, we demonstrate the simultaneous optimization of the electrical and thermal transport properties of PbS-based compounds by alloying with GeS. The addition of GeS triggers a complex cascade of beneficial events as follows: Ge2+ substitution in Pb2+ and discordant off-center behavior; formation of Pb5Ge5S12 as stable second-phase inclusions through valence disproportionation of Ge2+ to Ge0 and Ge4+. PbS and Pb5Ge5S12 exhibit good conduction band energy alignment that preserves the high electron mobility; the formation of Pb5Ge5S12 increases the electron carrier concentration by introducing S vacancies. Sb doping as the electron donor produces a large power factor and low lattice thermal conductivity (κlat) of ∼0.61 W m-1 K-1. The highest performance was obtained for the 14% GeS-alloyed samples, which exhibited an increased room-temperature electron mobility of ∼121 cm2 V-1 s-1 for 3 × 1019 cm-3 carrier density and a ZT of 1.32 at 923 K. This is ∼55% greater than the corresponding Sb-doped PbS sample and is one of the highest reported for the n-type PbS system. Moreover, the average ZT (ZTavg) of ∼0.76 from 400 to 923 K is the highest for PbS-based systems.

Ultralow Thermal Conductivity in Diamondoid Structures and High Thermoelectric Performance in (Cu1-xAgx)(In1-yGay)Te2.

Owing to the diversity of composition and excellent transport properties, the ternary I-III-VI2 type diamond-like chalcopyrite compounds are attractive functional semiconductors, including as thermoelectric materials. In this family, CuInTe2 and CuGaTe2 are well investigated and achieve maximum ZT values of ∼1.4 at 950 K and an average ZT of 0.43. However, both compounds have poor electrical conductivity at low temperature, resulting in low ZT below 450 K. In this work, we have greatly improved the thermoelectric performance in the quinary diamondoid compound (Cu0.8Ag0.2)(In0.2Ga0.8)Te2 by understanding and controlling the effects of different constituent elements on the thermoelectric transport properties. Our combined theoretical and experimental effort indicates that Ga in the In site of the lattice decreases the carrier effective mass and improves the electrical conductivity and power factor of Cu0.8Ag0.2In1-xGaxTe2. Furthermore, Ag in the Cu site strongly suppresses the heat transport via the enhanced acoustic phonon-optical phonon coupling effects, leading to the ultralow thermal conductivity of ∼0.49 W m-1 K-1 at 850 K in Cu0.8Ag0.2In0.2Ga0.8Te2. Defect formation energy calculations suggest intrinsic Cu vacancies introduce defect levels that are important to the temperature-dependent hole density and electrical conductivity. Therefore, we introduced extra Cu vacancies to optimize the hole carrier density and improve the power factor of Cu0.8Ag0.2In0.2Ga0.8Te2. As a result, a maximum ZT of ∼1.5 at 850 K and an average ZT of 0.78 in the temperature range of 400-850 K are obtained, which is among the highest in the diamond-like compound family.

All-Inorganic Halide Perovskites as Potential Thermoelectric Materials: Dynamic Cation off-Centering Induces Ultralow Thermal Conductivity.

Halide perovskites are anticipated to impact next generation high performance solar cells because of their extraordinary charge transport and optoelectronic properties. However, their thermal transport behavior has received limited attention. In this work, we studied the thermal transport and thermoelectric properties of the CsSnBr3-xIx perovskites. We find a strong correlation between lattice dynamics and an ultralow thermal conductivity for series CsSnBr3-xIx reaching 0.32 Wm-1K-1 at 550 K. The CsSnBr3-xIx also possess a decent Seebeck coefficient and controllable electrical transport properties. The crystallography data and theoretical calculations suggest the Cs atom deviates from its ideal cuboctahedral geometry imposed by the perovskite cage and behaves as a heavy atom rattling oscillator. This off-center tendency of Cs, together with the distortion of SnX6 (X = Br or I) octahedra, produces a highly dynamic and disordered structure in CsSnBr3-xIx, which gives rise to a very low Debye temperature and phonon velocity. Moreover, the low temperature heat capacity data suggests strong coupling between the low frequency optical phonons and heat carrying acoustical phonons. This induces strong phonon resonance scattering that induces the ultralow lattice thermal conductivity of CsSnBr3-xIx.

Determining the Mutation Bias of Favipiravir in Influenza Virus Using Next-Generation Sequencing.

Favipiravir is a broad-spectrum antiviral drug that may be used to treat influenza. Previous research has identified that favipiravir likely acts as a mutagen, but the precise mutation bias that favipiravir induces in influenza virus RNAs has not been described. Here, we use next-generation sequencing (NGS) with barcoding of individual RNA molecules to accurately and quantitatively detect favipiravir-induced mutations and to sample orders of magnitude more mutations than would be possible through Sanger sequencing. We demonstrate that favipiravir causes mutations and show that favipiravir primarily acts as a guanine analogue and secondarily as an adenine analogue resulting in the accumulation of transition mutations. We also use a standard NGS pipeline to show that the mutagenic effect of favipiravir can be measured by whole-genome sequencing of virus.IMPORTANCE New antiviral drugs are needed as a first line of defense in the event of a novel influenza pandemic. Favipiravir is a broad-spectrum antiviral which is effective against influenza. The exact mechanism of how favipiravir works to inhibit influenza is still unclear. We used next-generation sequencing (NGS) to demonstrate that favipiravir causes mutations in influenza RNA. The greater depth of NGS sequence information over traditional sequencing methods allowed us to precisely determine the bias of particular mutations caused by favipiravir. NGS can also be used in a standard diagnostic pipeline to show that favipiravir is acting on the virus by revealing the mutation bias pattern typical to the drug. Our work will aid in testing whether viruses are resistant to favipiravir and may help demonstrate the effect of favipiravir on viruses in a clinical setting. This will be important if favipiravir is used during a future influenza pandemic.

Large Thermal Conductivity Drops in the Diamondoid Lattice of CuFeS2 by Discordant Atom Doping.

Doping in a lattice refers to the introduction of very small quantities of foreign atoms and has a generally small effect on decreasing the lattice thermal conductivity, unlike alloying which involves large fractions of other elements and strongly enhances point defect phonon scattering. Here, we report that, by alloying only 3% of In on the Cu sites of the diamond-like lattice of CuFeS2 chalcopyrite compound (Cu1-xInxFeS2, x = 0.03) has a disproportionally large effect in reducing the lattice thermal conductivity of the compound from 2.32 to 1.36 Wm-1K-1 at 630 K. We find that In is not fully ionized to +3 when on the Cu sublattice and exists mainly in the +1 oxidation state. The 5s2 lone pair of electrons of In+ makes this atom incompatible (referred to as discordant) with the tetrahedral geometry of the crystallographic site. This causes strong local bond distortions thereby softening the In-S and Cu-S chemical bonds and introducing localized low frequency vibrations. The latter couple with the base phonon frequencies of the CuFeS2 matrix enhancing the anharmonicity and decreasing the phonon velocity, and consequently the lattice thermal conductivity. The control material in which the In doping is on the Fe3+ site of the structure at the same doping level (and found in the site-compatible In3+ state), has a far smaller effect on the phonon scattering.

Origin of Intrinsically Low Thermal Conductivity in Talnakhite Cu17.6Fe17.6S32 Thermoelectric Material: Correlations between Lattice Dynamics and Thermal Transport.

Understanding the nature of phonon transport in solids and the underlying mechanism linking lattice dynamics and thermal conductivity is important in many fields, including the development of efficient thermoelectric materials where a low lattice thermal conductivity is required. Herein, we choose the pair of synthetic chalcopyrite CuFeS2 and talnakhite Cu17.6Fe17.6S32 compounds, which possess the same elements and very similar crystal structures but very different phonon transport, as contrasting examples to study the influence of lattice dynamics and chemical bonding on the thermal transport properties. Chemically, talnakhite derives from chalcopyrite by inserting extra Cu and Fe atoms in the chalcopyrite lattice. The CuFeS2 compound has a lattice thermal conductivity of 2.37 W m-1 K-1 at 625 K, while Cu17.6Fe17.6S32 features Cu/Fe disorder and possesses an extremely low lattice thermal conductivity of merely 0.6 W m-1 K-1 at 625 K, approaching the amorphous limit κmin. Low-temperature heat capacity measurements and phonon calculations point to a large anharmonicity and low Debye temperature in Cu17.6Fe17.6S32, originating from weaker chemical bonds. Moreover, Mössbauer spectroscopy suggests that the state of Fe atoms in Cu17.6Fe17.6S32 is partially disordered, which induces the enhanced alloy scattering. All of the above peculiar features, absent in CuFeS2, contribute to the extremely low lattice thermal conductivity of the Cu17.6Fe17.6S32 compound.

Rhombohedral to Cubic Conversion of GeTe via MnTe Alloying Leads to Ultralow Thermal Conductivity, Electronic Band Convergence, and High Thermoelectric Performance.

In this study, a series of Ge1-xMnxTe (x = 0-0.21) compounds were prepared by a melting-quenching-annealing process combined with spark plasma sintering (SPS). The effect of alloying MnTe into GeTe on the structure and thermoelectric properties of Ge1-xMnxTe is profound. With increasing content of MnTe, the structure of the Ge1-xMnxTe compounds gradually changes from rhombohedral to cubic, and the known R3m to Fm-3m phase transition temperature of GeTe moves from 700 K closer to room temperature. First-principles density functional theory calculations show that alloying MnTe into GeTe decreases the energy difference between the light and heavy valence bands in both the R3m and Fm-3m structures, enhancing a multiband character of the valence band edge that increases the hole carrier effective mass. The effect of this band convergence is a significant enhancement in the carrier effective mass from 1.44 m0 (GeTe) to 6.15 m0 (Ge0.85Mn0.15Te). In addition, alloying with MnTe decreases the phonon relaxation time by enhancing alloy scattering, reduces the phonon velocity, and increases Ge vacancies all of which result in an ultralow lattice thermal conductivity of 0.13 W m-1 K-1 at 823 K. Subsequent doping of the Ge0.9Mn0.1Te compositions with Sb lowers the typical very high hole carrier concentration and brings it closer to its optimal value enhancing the power factor, which combined with the ultralow thermal conductivity yields a maximum ZT value of 1.61 at 823 K (for Ge0.86Mn0.10Sb0.04Te). The average ZT value of the compound over the temperature range 400-800 K is 1.09, making it the best GeTe-based thermoelectric material.

Synthetic dual co-stimulation increases the potency of HIT and TCR-targeted cell therapies.

Chimeric antigen receptor T cells have dramatically improved the treatment of hematologic malignancies. T cell antigen receptor (TCR)-based cell therapies are yet to achieve comparable outcomes. Importantly, chimeric antigen receptors not only target selected antigens but also reprogram T cell functions through the co-stimulatory pathways that they engage upon antigen recognition. We show here that a fusion receptor comprising the CD80 ectodomain and the 4-1BB cytoplasmic domain, termed 80BB, acts as both a ligand and a receptor to engage the CD28 and 4-1BB pathways, thereby increasing the antitumor potency of human leukocyte antigen-independent TCR (HIT) receptor- or TCR-engineered T cells and tumor-infiltrating lymphocytes. Furthermore, 80BB serves as a switch receptor that provides agonistic 4-1BB co-stimulation upon its ligation by the inhibitory CTLA4 molecule. By combining multiple co-stimulatory features in a single antigen-agnostic synthetic receptor, 80BB is a promising tool to sustain CD3-dependent T cell responses in a wide range of targeted immunotherapies.

Realizing high-efficiency thermoelectric module by suppressing donor-like effect and improving preferred orientation in n-type Bi2(Te, Se)3.

Thermoelectric materials have a wide range of application because they can be directly used in refrigeration and power generation. And the Bi2Te3 stand out because of its excellent thermoelectric performance and are used in commercial thermoelectric devices. However, n-type Bi2Te3 has seriously hindered the development of Bi2Te3-based thermoelectric devices due to its weak mechanical properties and inferior thermoelectric performance. Therefore, it is urgent to develop a high-performance n-type Bi2Te3 polycrystalline. In this work, we employed interstitial Cu and the hot deformation process to optimize the thermoelectric properties of Bi2Te2.7Se0.3, and a high-performance thermoelectric module was fabricated based on this material. Our combined theoretical and experimental effort indicates that the interstitial Cu reduce the defect density in the matrix and suppresses the donor-like effect, leading to a lattice plainification effect in the material. In addition, the two-step hot deformation process significantly improves the preferred orientation of the material and boosts the mobility. As a result, a maximum ZT of 1.27 at 373 K and a remarkable high ZTave of 1.22 across the temperature range of 300-425 K are obtained. The thermoelectric generator (TEG, 7-pair) and thermoelectric cooling (TEC, 127-pair) modules were fabricated with our n-type textured Cu0.01Bi2Te2.7Se0.3 coupled with commercial p-type Bi2Te3. The TEC module demonstrates superior cooling efficiency compared with the commercial Bi2Te3 device, achieving a ΔT of 65 and 83.4 K when the hot end temperature at 300 and 350 K, respectively. In addition, the TEG module attains an impressive conversion efficiency of 6.5% at a ΔT of 225 K, which is almost the highest value among the reported Bi2Te3-based TEG modules.

Realizing thermoelectric cooling and power generation in N-type PbS0.6Se0.4 via lattice plainification and interstitial doping.

Thermoelectrics have great potential for use in waste heat recovery to improve energy utilization. Moreover, serving as a solid-state heat pump, they have found practical application in cooling electronic products. Nevertheless, the scarcity of commercial Bi2Te3 raw materials has impeded the sustainable and widespread application of thermoelectric technology. In this study, we developed a low-cost and earth-abundant PbS compound with impressive thermoelectric performance. The optimized n-type PbS material achieved a record-high room temperature ZT of 0.64 in this system. Additionally, the first thermoelectric cooling device based on n-type PbS was fabricated, which exhibits a remarkable cooling temperature difference of ~36.9 K at room temperature. Meanwhile, the power generation efficiency of a single-leg device employing our n-type PbS material reaches ~8%, showing significant potential in harvesting waste heat into valuable electrical power. This study demonstrates the feasibility of sustainable n-type PbS as a viable alternative to commercial Bi2Te3, thereby extending the application of thermoelectrics.

Enhanced Thermoelectric Properties of Cu2SnSe3-Based Materials with Ag2Se Addition.

In this work, (Ag, In)-co-doped Cu2SnSe3-based compounds are prepared using a self-propagating high-temperature synthesis process. Ag2Se and as-synthesized (Ag, In)-co-doped Cu2SnSe3-based powders are mixed in a proportion according to the formula of Cu1.85Ag0.15Sn0.91In0.09Se3/x Ag2Se (x = 0, 3, 4, and 5%), which is followed by a subsequent plasma-activated sintering (PAS) to obtain consolidated composite bulks. A sandwich experiment is designed to reveal the evolution of the microstructure and phase composition of the composite samples during the PAS process. We investigate the reaction mechanism between Ag2Se and Cu2SnSe3-based matrix as well as the influence of Ag2Se on the phase composition, microstructure, and thermoelectric transport properties of the composites. Ag2Se addition is proven to be effective to improve Ag solubility in the Cu1.85Ag0.15Sn0.91In0.09Se3 matrix and introduce a CuSe secondary phase and an Ag-rich phase at grain boundaries. The electrical conductivity of Cu1.85Ag0.15Sn0.91In0.09Se3/x Ag2Se (x = 0, 3, 4, and 5%) composites decreases while the Seebeck coefficient increases with increasing Ag2Se addition, resulting in an optimized power factor. Moreover, benefiting from the collective phonon scattering at various defects induced by Ag2Se addition, the composite samples exhibit significantly suppressed lattice thermal conductivity, which reaches as low as 0.11 W m-1 K-1 at 700 K for the x = 5% sample. A peak figure-of-merit (ZT) of 1.26 at 750 K and an average ZT of 0.75 at 300-800 K are obtained for Cu1.85Ag0.15Sn0.91In0.09Se3/5% Ag2Se. This work provides an efficient way to improve average ZT values of Cu2SnSe3-based compounds for promising power generation at intermediate temperatures.