Paper-based plasma sanitizers.

This work describes disposable plasma generators made from metallized paper. The fabricated plasma generators with layered and patterned sheets of paper provide a simple and flexible format for dielectric barrier discharge to create atmospheric plasma without an applied vacuum. The porosity of paper allows gas to permeate its bulk volume and fuel plasma, while plasma-induced forced convection cools the substrate. When electrically driven with oscillating peak-to-peak potentials of ±1 to ±10 kV, the paper-based devices produced both volume and surface plasmas capable of killing microbes. The plasma sanitizers deactivated greater than 99% of Saccharomyces cerevisiae and greater than 99.9% of Escherichia coli cells with 30 s of noncontact treatment. Characterization of plasma generated from the sanitizers revealed a detectable level of UV-C (1.9 nW⋅cm-2⋅nm-1), modest surface temperature (60 °C with 60 s of activation), and a high level of ozone (13 ppm with 60 s of activation). These results deliver insights into the mechanisms and suitability of paper-based substrates for active antimicrobial sanitization with scalable, flexible sheets. In addition, this work shows how paper-based generators are conformable to curved surfaces, appropriate for kirigami-like "stretchy" structures, compatible with user interfaces, and suitable for sanitization of microbes aerosolized onto a surface. In general, these disposable plasma generators represent progress toward biodegradable devices based on flexible renewable materials, which may impact the future design of protective garments, skin-like sensors for robots or prosthetics, and user interfaces in contaminated environments.

Effects of forest regeneration types on phosphorus fractions of soil aggregates in subtropical forest.

Soil aggregates are important for the storage and availability of phosphorus in the soil. However, how forest regeneration types affect phosphorus fractions of soil aggregates remains unclear. In this study, we examined the composition of aggregate particle size, phosphorus fractions, phosphorus sorption capacity index (PSOR), legacy phosphorus index (PLGC) and degree of phosphorus saturation by Mehlich 3 (DPSM3) in bulk soils and soil aggregates of Castanopsis carlesii secondary forest (slight disturbance), C. carlesii human-assisted regeneration forest (moderate disturbance), and Cunninghamia lanceolata plantation (severe disturbance), aiming to explore the impact of forest regeneration types on phosphorus availability and supply potential of bulk soils and soil aggregates. The results showed that forest regeneration types significantly influenced the composition of soil aggregates. The proportion of coarse macroaggregates (>2 mm) in the soil of C. carlesii secondary forest and human-assisted regeneration forest was significantly higher than that in the C. lanceolata plantation, while the proportion of silt and clay fraction (<0.053 mm) showed an opposite trend. The composition of soil aggregates significantly affected the contents of different phosphorus fractions. The contents of soil labile phosphorus fractions (PSOL and PM3) decreased as aggregate particle size decreased. The contents of soil total phosphorus (TP), total organic phosphorus (Po), mode-rately labile phosphorus fractions (PiOH and PoOH), and occluded phosphorus (POCL), as well as PSOR and PLGC, exhibited a trend of decreasing at the beginning and then increasing as particle size decreased. The contents of TP, Po, and PiOH in coarse and silt macroaggregates was significantly higher than that in fine macroaggregates (0.25-2 mm) and microaggregates (0.053-0.25 mm). Forest regeneration types significantly influenced the contents of phosphorus fractions of bulk soils and soil aggregates. The contents of TP, Po, PSOL, and PM3 in the soil of C. carlesii secondary forests was significantly higher than that in C. carlesii human-assisted regeneration forest and C. lanceolata plantation. The contents of PSOL and PM3 in different-sized aggregates of C. carlesii secondary forests were significantly higher than that in the C. lanceolata plantation. Forest regeneration types significantly influenced the composition and supply potential of phosphorus fractions in soil aggregates. The proportions of PSOL, and PM3 to TP in different-sized soil aggregates were significantly lower in C. carlesii human-assisted regeneration forest compared with C. carlesii secondary forest. PSOR and DPSM3 in different-sized soil aggregates were significantly lower in C. lanceolata plantation than that in C. carlesii secondary forest. Overall, our results indicated that natural regeneration is more favorable for maintaining soil phosphorus availability, and that forest regeneration affects soil phosphorus availa-bility and its supply potential by altering the composition of soil aggregates.

Tunable Electrical Properties of Embossed, Cellulose-Based Paper for Skin-like Sensing.

This article describes a process of fabricating highly porous paper from cellulosic fibers and carbon black (CB) with tunable conductivity. By embossing such paper, its porosity decreases while its conductivity increases. Tuning the porosity of composite paper alters the magnitude and trend of conductivity over a spectrum of concentrations of conductive particles. The largest increase in conductivity from 8.38 × 10-6 to 2.5 × 10-3 S/m by a factor of ∼300 occurred at a percolation threshold of 3.8 wt % (or 0.36 vol %) with the composite paper plastically compressed by 410 MPa, which caused a decrease of porosity from 88% to 42% on average. Our composite paper showed stable piezoresistive responses within a broad pressure range from 1 kPa up to 5.5 MPa for 800 cycles. The piezoresistive sensitivities of the composite paper were dependent on concentration and decreased with pressure. Composite paper with 7.5 wt % CB had sensitivities of -0.514 kPa-1 over applied pressures ranging from 1 to 50 kPa and -0.215 kPa-1 from 1 to 250 kPa. This piezoresistive paper with embossed patterns enabled touch sensing and detection of damage from darts and punches. Understanding the percolation behavior of three-phase composites (cellulosic fibers/conductive particles/air) and their response to damage, pressure, and processing conditions has the potential to enable scalable applications in prosthetics and robotics, haptic feedback, or structural health monitoring on expansive surfaces of buildings and vehicles.

A Practical Framework Toward Prediction of Breaking Force and Disintegration of Tablet Formulations Using Machine Learning Tools.

Enabling the paradigm of quality by design requires the ability to quantitatively correlate material properties and process variables to measureable product performance attributes. Conventional, quality-by-test methods for determining tablet breaking force and disintegration time usually involve destructive tests, which consume significant amount of time and labor and provide limited information. Recent advances in material characterization, statistical analysis, and machine learning have provided multiple tools that have the potential to develop nondestructive, fast, and accurate approaches in drug product development. In this work, a methodology to predict the breaking force and disintegration time of tablet formulations using nondestructive ultrasonics and machine learning tools was developed. The input variables to the model include intrinsic properties of formulation and extrinsic process variables influencing the tablet during manufacturing. The model has been applied to predict breaking force and disintegration time using small quantities of active pharmaceutical ingredient and prototype formulation designs. The novel approach presented is a step forward toward rational design of a robust drug product based on insight into the performance of common materials during formulation and process development. It may also help expedite drug product development timeline and reduce active pharmaceutical ingredient usage while improving efficiency of the overall process.

Rotary Actuators Based on Pneumatically Driven Elastomeric Structures.

Unique elastomeric rotary actuators based on pneumatically driven peristaltic motion are demonstrated. Using silicone-based wheels, these motors enable a new class of soft locomotion not found in nature, which is capable of withstanding impact, traversing irregular terrain, and operating in water. For soft robotics, this work marks progress toward providing torque without bending actuators.