Improving fourth harmonic generation performance by elevating the operation temperature of ADP crystal.

In current inertial confinement fusion (ICF) facilities, potassium dihydrogen phosphate (KH2PO4, KDP) type crystals are the only nonlinear optical (NLO) materials that can satisfy the aperture requirement of the ICF laser driver. Ammonium dihydrogen phosphate (NH4H2PO4, ADP) crystal is a typical isomer of KDP crystal, with a large nonlinear optical coefficient, high ultraviolet transmittance, and large growth sizes, which is an important deep ultraviolet (UV) NLO material. In this paper, we investigated the effect of ADP temperature on its fourth-harmonic-generation (FHG) performance. When the temperature of the ADP crystal was elevated to 48.9 °C, the 90° phase-matched FHG of the 1064 nm laser was realized. Compared with the 79° phase-matched FHG at room temperature (23.0 °C), the output energy at 266 nm, conversion efficiency, angular acceptance, and laser-induced damage threshold (LIDT) increased 113%, 71%, 623%, 19.6%, respectively. It shows that elevating ADP temperature is an efficient method to improve its deep UV frequency conversion properties, which may also be available to other NLO crystals. This discovery provides a very valuable technology for the future development of UV, deep UV lasers in ICF facilities.

High performance 1.9†µm passively Q-switched bulk laser with germanene as a saturable absorber.

Germanene is an analog of graphene, and its independent novel low-bending honeycomb structure gives outstanding advantages such as environmental stability and significant low-frequency optical absorbance. In this paper, the few-layer germanene was successfully prepared by the liquid phase exfoliation method. The saturable absorption characteristics of germanene in the infrared waveband were detected by the open-aperture Z-scan method. With germanene as a saturable absorber, a high-performance passively Q-switched bulk laser was realized at 1.9 µm. The shortest pulse width of 60.5 ns was obtained from continuous-wave pumping, corresponding to a single pulse energy of 6.7 µJ and peak power of 110 W. By utilizing the pulse pumping style with a repletion rate of 10 Hz, the single pulse energy and peak power increased to 45.8 µJ and 328 W, respectively, which exceeded all two-dimensional SA materials reported before. This research manifests that germanene is an excellent SA material for mid-infrared solid-state lasers.

Broadband second-harmonic-generation in GdCOB crystals.

Broadband second-harmonic-generation (SHG) in GdCOB crystals was demonstrated for the first time. Theoretical calculation and experiments for the type-I frequency doubling of GdCOB crystal was performed. The result revealed that the spectral retracing point of phase-matching angle was at around 1.65 µm. For broadband fundamental laser source tuning in the range of 1.55-1.7 µm, efficient SHG was realized, the highest conversion efficiency was 56%, and the output bandwidth reached 16 nm.

Bi3TeBO9: A Promising Mid-Infrared Nonlinear Optical Crystal with a Large Laser Damage Threshold.

Mid-infrared (mid-IR) nonlinear optical (NLO) crystals are key materials in the field of laser technology. Nevertheless, the applications of these significant optical materials are always limited by their low laser damage threshold (LDT). Here, an oxide mid-IR NLO crystal, Bi3TeBO9, with a large LDT was discovered. The centimeter-sized Bi3TeBO9 single crystal was successfully grown by the top-seeded solution growth (TSSG) method. The Bi3TeBO9 features a high LDT of 450 MW/cm2 (∼15 × AgGaS2) and the widest transparent range (0.35-7.10 µm) among known borate crystals. The second-harmonic generation (SHG) effect is about 1.6 times that of KDP. First-principles calculations and structural analysis show that the optical characteristics of Bi3TeBO9 are mainly affected by distorted [BiO6] groups. Furthermore, its thermal characteristics including specific heat, thermal diffusivity, thermal conductivity, and thermal expansion were also measured.

Recalibration of the nonlinear optical coefficients of BaGa4Se7 crystal using second-harmonic-generation method.

Nonlinear optical coefficients are important parameters for nonlinear optical crystals. Based on the previously disclosed BaGa4Se7 crystal coefficients, the optimum phase-matching direction with the largest effective nonlinear optical coefficient appears in the second octant (90∘<θ<180∘, 0∘<ϕ<90∘). In this study, a recalibration was performed using the second-harmonic-generation method, and it was confirmed that the optimum phase-matching direction of the BaGa4Se7 crystal is located in its XZ principal plane (ϕ=0∘). Therefore, this study will serve as a good reference for future applications of this excellent crystal.

Kerr-lens mode-locked Tm-doped sesquioxide ceramic laser.

Kerr-lens mode-locked solid-state laser operation at ∼2µm is investigated. Using a Tm3+-doped (Lu,Sc)2O3 "mixed" sesquioxide ceramic as a gain medium, pulses as short as 58 fs are generated at ∼2081nm via soft-aperture Kerr-lens mode locking. The average output power amounts to 220 mW at a pulse repetition rate of 84.8 MHz. The emitted spectrum at the long-wavelength wing extends to >2.2µm which is attributed to vibronic transitions of the Tm3+ ions. The latter is found to be essential for generating pulses with durations in the 50 fs range.

Tm:YAG single-crystal fiber laser.

In this Letter, to the best of our knowledge, we present the first thulium (Tm) single-crystal fiber (SCF) laser with free-space propagation of the laser beam only. The SCF is equipped with diffusion-bonded end caps of undoped YAG for better thermal management and enhancement of pump guiding. By utilizing mode matching and pump guiding in different SCF parts, an output power of 9.1 W is achieved at ∼2.02µm with a slope efficiency of 49.4%. This straightforward approach, which is also simple to realize and is based on combining the advantages of fiber-geometry structure and crystalline properties of Tm:YAG, is expected to be useful for 2 µm amplification stages in different time formats as well.

Remarkable temperature-dependent second-harmonic-generation performance of a YCOB crystal.

For the first time, the temperature stability of second-harmonic-generation (SHG) is reported for the entire space of a YCa4O(BO3)3 (YCOB) crystal for a temperature range of -10 - 520 °C. Both theoretical calculations and experimental data indicate an optimum phase-matching (PM) direction of (θ = 149.2°, ϕ = 0°), which is located in the XZ principle plane (90° < θ < 180°). A special regression phenomenon of the PM angle was found in this direction, which further increased the SHG output at high temperature (> 200 °C). As a result, for SHG of the Nd:YAG laser, the measured temperature bandwidth of a YCOB crystal cut along the optimum PM direction is larger than 490 °C·cm. As demonstrated in this study, among all nonlinear optical crystals, this cut-type is currently the best choice when temperature-insensitive SHG is required.

High-energy 2 µm pulsed vortex beam excitation from a Q-switched Tm:LuYAG laser.

We report on the first, to the best of our knowledge, direct generation of pulsed vortex beams at 2 µm from a ${ Q}$Q-switched Tm:LuYAG laser. High-energy Laguerre-Gaussian (${{\rm LG}_{0,l}}$LG0,l) pulsed laser beams with well-defined handedness are selectively excited through spatially matched pump gain distribution and asymmetric cavity loss without using any intracavity handedness-selective optical elements. Pulse energies of 1.48 mJ for the ${{\rm LG}_{0, + 1}}$LG0,+1 mode and 1.51 mJ for the ${{\rm LG}_{0, - 1}}$LG0,-1 mode, respectively, are achieved at a repetition rate of 500 Hz. The pulsed laser beams with helical wavefronts are potentially useful for studying orbital angular momentum transformation dynamics, generation of mid-IR vortex beams, and nanostructuring of organic materials.

Graphene and SESAM mode-locked Yb:CNGS lasers with self-frequency doubling properties.

We report on mode-locking of an Yb:Ca3NbGa3Si2O14 laser, which is pumped by a fiber-coupled single-mode laser diode. The shortest pulse duration obtained with a semiconductor saturable absorber mirror is 52 fs, with 75 mW of average output power. Sub-60 fs operation tunable between 1055 and 1074 nm is achieved by employing semiconductor absorbers with different characteristics. We also demonstrate passive mode-locking results with transmissive graphene saturable absorber, reaching an 85 fs pulse duration with 23 mW output power. Moreover, we present the non-phase-matched self-frequency doubling properties of this non-centrosymmetric crystal in the femtosecond regime.

Temperature bandwidth of second-harmonic-generation in GdCOB crystal.

The temperature bandwidth of the second harmonic generation (SHG) phase-matching process was investigated for the GdCa4O(BO3)3 (GdCOB) crystal. GdCOB exhibits a much broader temperature bandwidth in comparison with many familiar nonlinear optical (NLO) crystals. For a fundamental wave of 1,064 nm, the maximum temperature bandwidth appeared at (θ=135°, ϕ=47.3°), as predicted by the theoretical calculation and demonstrated by the SHG experiments. The GdCOB crystal is a good candidate for NLO frequency conversions under extreme temperatures.

2.7 µm optical vortex beam directly generated from an Er:Y2O3 ceramic laser.

We demonstrate, to the best of our knowledge, the first direct vortex beam generation in the 3 µm spectral region by employing an Er:Y2O3 ceramic laser. Controllable handedness with high purity is achieved by introducing asymmetric cavity loss and reducing the number of longitudinal modes. The average orbital angular momentum of the produced scalar vortex beam is quantitatively evaluated to be 0.95h for the LG0,+1 mode and -0.94h for the LG0,-1 mode. The corresponding optical spectrum is centered at 2710.8 and 2710.5 nm, respectively.

Tin diselenide-based saturable absorbers for eye-safe pulse lasers.

Eye-safe pulse lasers have attracted increasing attention due to their potential wide application in many fields. However, optical modulators with excellent nonlinear optical absorption properties in the range of 1.4-2.1 µm are still very scarce. In this study, tin diselenide (SnSe2), a newly-developed 2D layered semiconductor material with facile processability and low cost, was investigated. The nonlinear optical response of SnSe2 was investigated using the open aperture Z-scan method at 1500 and 1800 nm. Using SnSe2 as the saturable absorber, a passive Q-switched solid-state laser was realized at 1.3 and 1.9 µm for the first time. This study proved SnSe2 to be an effective optical modulating material for the eye-safe waveband.

Comparison of hydrogen vacancies in KDP and ADP crystals: a combination of density functional theory calculations and experiment.

The hydrogen vacancy (VH) is the most common point defect that may lead to optical damage of potassium dihydrogen phosphate (KDP) and its analog ammonium dihydrogen phosphate (ADP), further limiting their practical application in high-power laser systems. In this work, we have grown KDP and ADP crystals by using a rapid growth method, and investigated the physical origin of the different stability of VH as well as the defect-induced electronic structure and optical absorption in KDP and ADP crystals. The inclusion of van der Waals correction to density functional theory calculations is found to have little influence on VH energetics of KDP whereas it largely reduces the charge transition level ε(+/-) of VH by >2 eV in ADP. It is found that hydrogen vacancies mainly contribute to the redshift of the measured absorption edges of both KDP and ADP crystals. Owing to the varied lattice environments and locations, the VH defects exhibit different stability, and electronic and optical properties in KDP and ADP crystals. Notably, the extra optical absorption caused by the positively-charged VH in KDP could be largely reduced by decreasing the defect concentration, whereas ADP exhibits defect-location dependence - the optical damage center of the VH in the NH4+ group could not be eliminated because of electron capture of its neighboring N atoms. The calculation results help us to better understand the origin of laser damage in KDP and ADP crystals.

Passively Q-switched Nd3+ solid-state lasers with antimonene as saturable absorber.

Based on the saturable absorption feature of a two-dimensional (2D) nano-material, antimonene, the passively Q-switched operation for solid-state laser was realized for the first time. For the 946 and 1064 nm laser emissions of the Nd:YAG crystal, the Q-switched pulse widths were 209 and 129 ns, and the peak powers were 1.48, 1.77 W, respectively. For the 1342 nm laser emission of the Nd:YVO4 crystal, the Q-switched pulse width was 48 ns, giving a peak power of 28.17 W. Our research shows that antimonene can be used as a stable, broadband optical modulating device for a solid-state laser, which will be particularly effective for long wavelength operation.

Efficient laser operations of unprocessed thin plate of Nd:YPO4 crystal.

The laser properties of Nd:YPO4 crystal were demonstrated for the first time. For a 1.2 at.% doped Nd:YPO4 crystal, the absorption cross-section at 803 nm, stimulated emission cross-section at 1063 nm, and fluorescence lifetime was measured to be 8.1 × 10-20 cm2, 1.6 × 10-19 cm2, 156 µs, respectively. With an as-grown 0.6 mm thin slice which was unpolished and uncoated, efficient diode-pumped continue-wave (CW) laser operations were realized at 1.06 and 1.3 µm wavebands. The 1063 nm output power reached 2.16 W when the absorbed pump power was 4.07 W, corresponding to an optical-to-optical efficiency of 53%, and a slope efficiency of 56.4%. The 1.3 µm laser output exhibited the simultaneous operations of dual-wavelengths, i.e. 1338 and 1347 nm. The maximum output power was 800 mW at an absorbed pump power of 3.08 W, giving an optical-to-optical efficiency of 26% and a slope efficiency of 28.2%.

Nonlinear absorption properties of silicene nanosheets.

As the cousins of graphene, i.e. same group IVA element, the nonlinear absorption (NLA) properties of silicene nanosheets were rarely studied. In this paper, we successfully exfoliated the two-dimensional silicene nanosheets from bulk silicon crystal using liquid phase exfoliation method. The NLA properties of silicene nanosheets were systemically investigated for the first time, as we have known. Silicene performed exciting saturable absorption and two photon absorption (2PA) behavior. The lower saturable intensity and larger 2PA coefficient at 532 nm excitation indicates that silicene has potential application in ultrafast lasers and optical limiting devices, especially in visible waveband.

Passive Q switching of Yb:CNGS lasers by Cr4+:YAG and V3+:YAG saturable absorbers.

Trigonal langasite-type ordered silicate crystal Yb:Ca3NbGa3Si2O14 (Yb:CNGS) is a promising material for efficient ∼1 µm lasers. We report on the first passively Q-switched Yb:CNGS laser using Cr4+:YAG and V3+:YAG saturable absorbers (SAs) with a 976 nm volume-Bragg-grating-stabilized diode as a pump source. The laser crystal was a c cut 3 at.% Yb:CNGS grown by the Czochralski method. It was placed in a compact microchip-type laser cavity. With a Cr4+:YAG SA, very stable 62.2 µJ/4.4 ns pulses were achieved at a repetition rate of 22.5 kHz. The average output power was 1.40 W at 1015.3 nm, corresponding to a Q switching conversion efficiency of 90%. With the V3+:YAG SA, the pulse characteristics were 13.3 µJ/11.1 ns at a higher repetition rate of 68.4 kHz. The performance of the Yb:CNGS/Cr4+:YAG was numerically modeled showing a good agreement with the experiment.

Angular non-critical phase-matching second-harmonic-generation characteristics of RECOB (RE = Tm, Y, Gd, Sm, Nd and La) crystals.

For the first time, the angular non-critical phase-matching (A-NCPM) second-harmonic-generation (SHG) characteristics of a family of monoclinic oxoborate crystals, RECa4O(BO3)3 (RECOB, RE = Tm, Y, Gd, Sm, Nd and La), were comprehensively investigated. For all of the realizable A-NCPM SHG styles, the feature parameters including PM wavelength, angular, wavelength and temperature acceptance bandwidths, have been derived from the theory and verified by the experiments. We discovered that the closer the ion radius between RE3+ and Ca2+, the smaller the birefringence, and the better the A-NCPM SHG properties. As a result, for the Type-I SHG on Y-axis which has the largest effective nonlinear optical coefficient (deff) among the three realizable A-NCPM styles, NdCOB crystal presents the longest PM wavelength (927 nm), the largest angular acceptance bandwidth (Δθ⋅l1/2 = 84.3 mrad·cm1/2, Δϕ⋅l1/2 = 58.8 mrad·cm1/2), and the broadest wavelength acceptance bandwidth (8.7 nm). This discovery will contribute to the design of new NCPM materials, at the same time the parameter formula will be helpful for the theoretical prediction of NCPM performance.

Diode-pumped passively Q-switched self-frequency-doubled Nd:CNGS laser.

With Cr4+:YAG as a saturable absorber, a passively Q-switched self-frequency-doubled (SFD) laser based on a trigonal Nd:Ca3NbGa3Si2O14 (Nd:CNGS) silicate crystal was demonstrated for the first time. The maximum average output power at 532 nm was 16.2 mW, and the corresponding pulse repetition frequency, single pulse energy, pulse duration and peak power were 2.25 kHz, 7.2 µJ, 13.7 ns, 0.53 kW, respectively. We also present a rate-equation model of such a passively Q-switched SFD laser showing a good agreement with the experiment. Nd:CNGS is a promising pulse SFD material for miniature all-solid-state visible light sources.