Large-Area Uniaxially Oriented Sub-5†nm Line Patterns of Hybrid Liquid Crystals Constructed by Perylene Diimide and Oligo(Dimethylsiloxane).

Construction of sub-5 nm long-range ordered structures through self-assembly has received increasing attention. Herein, a series of ODMS-based thermotropic liquid crystals (LCs) containing perylene diimide (PDI) were designed and synthesized. These LCs can form ordered nanostructures with periodic sizes around 5 nm including smectic J (SmJ), oblique columnar (Colob ), and hexagonal columnar (Colh ) phases with change in the volume fraction of ODMS, where the layer spacing of the SmJ phase is less than 5 nm. Thin films with parallel oriented nanolines with line width less than 5 nm can be obtained on PDMS-modified silicon substrates by spin-casting and simple thermal annealing processes. Moreover, owing to the strong π-π interaction between PDI cores, these nanolines are long-range ordered with uniaxial orientation in relatively large areas (1.5×1.5 µm2 ) with over 300 continuous microdomains without pre-patterning. These nanostructures provide the possibility of preparing nanotemplates by oxygen plasma etching.

A Review of Weak Gel Fracturing Fluids for Deep Shale Gas Reservoirs.

Low-viscosity slickwater fracturing fluids are a crucial technology for the commercial development of shallow shale gas. However, in deep shale gas formations with high pressure, a higher sand concentration is required to support fractures. Linear gel fracturing fluids and crosslinked gel fracturing fluids have a strong sand-carrying capacity, but the drag reduction effect is poor, and it needs to be pre-prepared to decrease the fracturing cost. Slick water fracturing fluids have a strong drag reduction effect and low cost, but their sand-carrying capacity is poor and the fracturing fluid sand ratio is low. The research and development of viscous slick water fracturing fluids solves this problem. It can be switched on-line between a low-viscosity slick water fracturing fluid and high-viscosity weak gel fracturing fluid, which significantly reduces the cost of single-well fracturing. A polyacrylamide drag reducer is the core additive of slick water fracturing fluids. By adjusting its concentration, the control of the on-line viscosity of fracturing fluid can be realized, that is, 'low viscosity for drag reduction, high viscosity for sand-carrying'. Therefore, this article introduces the research and application status of a linear gel fracturing fluid, crosslinked gel fracturing fluid, and slick water fracturing fluid for deep shale gas reservoirs, and focuses on the research status of a viscous slick water fracturing fluid and viscosity-controllable polyacrylamide drag reducer, with the aim of providing valuable insights for the research on water-based fracturing fluids in the stimulation of deep shale gas reservoirs.

Impact of self-assembled structure on ionic conductivity of an azobenzene-containing electrolyte.

The type of self-assembled structure has a significant impact on the ionic conductivity of block copolymer or liquid crystalline (LC) ion conductors. In this study, we focus on the effect of self-assembled structures on the ionic conductivity of a non-block copolymer, LC ion conductor, which is a mixture of an azobenzene monomer (NbAzo), pentaerythritol tetre(3-mercapropionate) (PETMP), and a lithium salt, lithium bis(trifluoromethane)sulfonimide (LiTFSI). The self-assembled structures and ionic conductivities of ion conductors having different doping ratios of lithium salt to monomer were examined. With the increase in the doping ratio, the self-assembled structure transforms from lamellae (LAM) to double gyroid (GYR). The effect of self-assembled structure on ionic conductivity was analyzed; it was found that the conductivity of the GYR structure was about 3.6 times that of the LAM one, indicating that obtaining the GYR structure is more effective in improving ionic conductivity.

Strain-Stiffening Ionogel with High-Temperature Tolerance via the Synergy of Ionic Clusters and Hydrogen Bonds.

Highly stretchable and conductive ionogels have great potential in flexible electronics and soft robotic skins. However, current ionogels are still far from being able to accurately duplicate the mechanically responsive behavior of real human skin. Furthermore, durable robotic skins that are applicable under harsh conditions are still lacking. Herein, a strong noncovalent interaction, ionic clusters, is combined with hydrogen bonds to obtain a physically cross-linked ionogel (PCI). Benefiting from the strong ionic bonding of the ionic cluster, the PCI shows strain-stiffening behavior similar to that of human skin, thus enabling it to have a perception-strengthening ability. Additionally, the strong ionic clusters can also ensure the PCI remains stable at high temperatures. Even when the temperature is raised to 200 °C, the PCI can maintain the gel state. Moreover, the PCI exhibits high transparency, recyclability, good adhesion, and high conductivity. Such excellent features distinguish the PCI from ordinary ionogels, providing a new way to realize skin-like sensing in harsh environments for future bionic machines.