RESUMO
Cell-substrate interaction is important in tissue engineering. Vascular smooth muscle cells (VSMCs) cultured on the microgrooved surface of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) showed a distinctive polarized morphology and a high expression level of let-7a compared with the flat substrates. LIMK2, a crucial regulator of actin dynamics, was identified as a new target of let-7a. F-Actin content on flat substrates was significantly higher than that on microgrooved ones. Either overexpression of let-7a on flat substrates or inhibited expression on microgrooved substrates can rescue the difference. In accord with actin dynamics, the expressions of contractile smooth muscle markers, such as SM22 and SMA, decreased in VSMCs cultured on microgrooved substrates compared to those on flat ones, though PHBHHx can induce the synthetic-to-contractile phenotype shift. These results indicate that microgrooved PHBHHx could enhance actin dynamics of VSMCs through let-7a-involved regulation and trigger a synthetic shift.
Assuntos
Ácido 3-Hidroxibutírico/química , Materiais Biocompatíveis/química , Caproatos/química , MicroRNAs/metabolismo , Músculo Liso Vascular/fisiologia , Engenharia Tecidual/métodos , Actinas/metabolismo , Animais , Aorta/citologia , Técnicas de Cultura de Células , Linhagem Celular , Regulação da Expressão Gênica , Quinases Lim/metabolismo , Teste de Materiais , Camundongos , Propriedades de SuperfícieRESUMO
The behavior of recrystallization and grain growth was examined in Cu-Cu joints during electromigration at 150 °C. Recrystallization and grain growth were observed in all the joints after electromigration for 9000 h. Voiding was formed in Cu current-feeding lines and in bonding interfaces, and resistance increased with time due to the void formation. However, instead of rising abruptly, the resistance of certain Cu joints dropped after 7000 h. Microstructural analysis revealed that a large grain growth occurred in these joints at 150 °C, and the bonding interface was eliminated. Therefore, the electromigration lifetime can be prolonged for these joints.
RESUMO
Highly (111)-oriented nanotwinned Cu (nt-Cu) films were fabricated on silicon wafers for thermal-stress characterization. We tailored the microstructural features (grain scale and orientation) of the films by tuning the electroplating parameters. The films were heat-treated and the relaxation behaviors of thermal stresses in the films were explored using a bending beam system. Focused ion beam (FIB) and electron back-scattered diffraction (EBSD) were then employed to characterize the transformations of the microstructure, grain size, and orientation degree of the films. The results indicated that the degree of (111)-preferred orientation and grain size significantly decrease with increasing the current density. The nt-Cu films with a higher degree of (111)-preferred orientation and larger grains exhibit the slower rates of stress relaxation. The film with larger grains possesses a smaller grain boundary area; thus, the grain boundary diffusion for the thermal-stress release is suppressed. In addition, the induced tensile stress in the films with larger grains is smaller leading to the difference in microstructural changes under annealing.
RESUMO
X-ray nanodiffraction was used to measure the thermal stress of 10 µm nanotwinned Cu bumps in Cu/SiO2 hybrid structures at -55 °C, 27 °C, 100 °C, 150 °C, and 200 °C. Bonding can be achieved without externally applied compression. The X-ray beam size is about 100 nm in diameter. The Cu bump is dominated by (111) oriented nano-twins. Before the hybrid bonding, the thermal stress in Cu bumps is compressive and remains compressive after bonding. The average stress in the bonded Cu joint at 200 °C is as large as -169.1 MPa. In addition, using the strain data measured at various temperatures, one can calculate the effective thermal expansion coefficient (CTE) for the 10 µm Cu bumps confined by the SiO2 dielectrics. This study reports a useful approach on measuring the strain and stress in oriented metal bumps confined by SiO2 dielectrics. The results also provide a deeper understanding on the mechanism of hybrid bonding without externally applied compression.
RESUMO
We adopted (111)-oriented Cu with high surface diffusivity to achieve low-temperature and low-pressure Cu/SiO2 hybrid bonding. Electroplating was employed to fabricate arrays of Cu vias with 78% (111) surface grains. The bonding temperature can be lowered to 200 °C, and the pressure is as low as 1.06 MPa. The bonding process can be accomplished by a 12-inch wafer-to-wafer scheme. The measured specific contact resistance is 1.2 × 10-9 Ω·cm2, which is the lowest value reported in related literature for Cu-Cu joints bonded below 300 °C. The joints possess excellent thermal stability up to 375 °C. The bonding mechanism is also presented to provide more understanding on hybrid bonding.
RESUMO
Record power conversion efficiencies (PCEs) of perovskite solar cells (PSCs) have been obtained with the organic hole transporter 2,2',7,7'-tetrakis(N,N-di-p-methoxyphenyl-amine)9,9'-spirobifluorene (spiro-OMeTAD). Conventional doping of spiro-OMeTAD with hygroscopic lithium salts and volatile 4-tert-butylpyridine is a time-consuming process and also leads to poor device stability. We developed a new doping strategy for spiro-OMeTAD that avoids post-oxidation by using stable organic radicals as the dopant and ionic salts as the doping modulator (referred to as ion-modulated radical doping). We achieved PCEs of >25% and much-improved device stability under harsh conditions. The radicals provide hole polarons that instantly increase the conductivity and work function (WF), and ionic salts further modulate the WF by affecting the energetics of the hole polarons. This organic semiconductor doping strategy, which decouples conductivity and WF tunability, could inspire further optimization in other optoelectronic devices.
RESUMO
The scalability of highly efficient organic-inorganic perovskite solar cells (PSCs) is one of the major challenges of solar module manufacturing. Various scalable methods have been explored to strive for uniform perovskite films of high crystal quality on large-area substrates, but each of these methods has individual limitations on the potential of successful commercialization of perovskite photovoltaics. Here, we report a fully scalable hybrid process, which combines vapor- and solution-based techniques to deposit high quality uniform perovskite films on large-area substrates. This two-step process does not use toxic solvents, and it further allows easy implementation of passivation strategies and additives. We fabricate PSCs based on this process and use blade coating to deposit a SnO2 electron transporting layer and Spiro-OMeTAD hole transporting layer without halogenated solvents in ambient air. The fabricated PSCs have achieved open-circuit voltage up to 1.16 V and power conversion efficiency of 18.7% with good uniformity on 5 cm × 5 cm substrates.
RESUMO
Cell-substrate interaction is one of the most important aspects of tissue engineering. Changes of MSCs interfacial behaviors were found to be triggered by 10 µm wide grooved pattern on poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx). Global marker genes expression and miRNAs profiling analysis provided insights into the regulation network of the topography induced MSCs' cell responses including adhesion, proliferation, differentiation and apoptosis. Compared to MSCs cultured on the smooth substrates, MSCs incubated on microgrooved PHBHHx substrates showed increased expression of osteogenesis-related marker genes including cbfa1, col1a1 and bmp2, and decreased expression of vcl, vinculin encoding gene, adipogenesis-related genes including lpl, des and acta2, as well as myogenesis-related genes of myh11 and nse. The miRNA microarrays revealed that 18 differentially-expressed miRNAs on microgrooved pattern had multiple target genes, contributing comprehensively to the cellular regulation process. Similar to the topography-triggered ostegenenesis, co-transfection of the osteogenic miRNAs combination (miR-140, miR-214, miR-320, miR-351 and miR-674-5p) was able to stimulate the expression of osteogenic marker genes. This study elucidated the important roles of miRNAs in the regulation processes of the microenvironment triggered cell behaviors, and provided clues for the PHA biomedical materials development.