Damage morphologies of Al2O3 and Fe particles attached on the input surface of fused silica after irradiation by a 355 nm laser.

Particulate contamination on the optical surface can seriously degrade the performance of optics working in the high peak power laser system. In this study, we show that the nature of optical damages on the input surface induced by particles depends on the optical property of the particles. Ceramic Al2O3 particles tend to cause micro-fractures to the optical surface, but metallic Fe particles mainly undergo ablation on the substrate. Different microscopes are used to characterize their damage morphologies, and the light distribution and thermal evolution of two different particles are simulated, focusing on better understanding their special damage morphologies.

An Ultra-Sensitive Multi-Functional Optical Micro/Nanofiber Based on Stretchable Encapsulation.

Stretchable optical fiber sensors (SOFSs), which are promising and ultra-sensitive next-generation sensors, have achieved prominent success in applications including health monitoring, robotics, and biological-electronic interfaces. Here, we report an ultra-sensitive multi-functional optical micro/nanofiber embedded with a flexible polydimethylsiloxane (PDMS) membrane, which is compatible with wearable optical sensors. Based on the effect of a strong evanescent field, the as-fabricated SOFS is highly sensitive to strain, achieving high sensitivity with a peak gauge factor of 450. In addition, considering the large negative thermo-optic coefficient of PDMS, temperature measurements in the range of 30 to 60 °C were realized, resulting in a 0.02 dBm/°C response. In addition, wide-range detection of humidity was demonstrated by a peak sensitivity of 0.5 dB/% RH, with less than 10% variation at each humidity stage. The robust sensing performance, together with the flexibility, enables the real-time monitoring of pulse, body temperature, and respiration. This as-fabricated SOFS provides significant potential for the practical application of wearable healthcare sensors.

Periodic surface structures on dielectrics upon femtosecond laser pulses irradiation.

The formation of laser-induced periodic surface structures (LIPSS) on two different dielectrics of K9 glass and fused silica upon irradiation in ambient conditions and in vacuum with multiple femtosecond (fs) laser pulse sequences at different pulse durations (35 fs, 260 fs, and 500 fs) was studied experimentally. Three types of LIPSS, so-called high-spatial-frequency LIPSS (HSFL), low-spatial-frequency LIPSS (LSFL), and supra-wavelength periodic surface structures (SWPSS) with different spatial periods and orientations were identified. The appearance was characterized with respect to the experimental parameters of laser fluence and number of laser pulses per spot. The crater morphologies - including nanoripples, periodic microgrooves, quasiperiodic microspikes, and central smooth zone - were observed by scanning electron microscope (SEM). The supra-wavelength structures exhibit periodicities, which are markedly, even multiple times, higher than the laser excitation wavelength. The SWPSS were formed with a broader range of laser fluences, upon the longer laser pulse durations (260 fs and 500 fs) and/or on the lower band-gap dielectrics (K9 glass), due to the deeper effective light penetration depths and thicker viscous surface layers formation. The HSFL were observed on the higher band-gap dielectrics (fused silica) and within a certain narrow laser parameter window. The formation mechanisms of LIPSS were also discussed.

The Characterization of Laser-Induced Particles Generated from Aluminum Alloy in High Power Laser Facility.

Aerosol particle contamination in high-power laser facilities has become a major cause of internal optical component damage resistance and service life reduction. In general, contaminating particles primarily originate from stray light; therefore, it is crucial to investigate the mechanism and dynamics of the dynamic contaminating particle generation to control the cleanliness level. In this study, corresponding research was conducted on experiments and theory. We investigated the particle generation and surface composition modification under the action of a laser. We employed various surface analytical methods to identify the possible variations in the aluminum alloy surface during laser irradiations. A theoretical model for particle ejection from aluminum alloy surfaces was established by taking the adhesion force and laser cleaning force (due to thermal expansion) into account. The results show that the threshold energies for contamination particle generation and damage are around 0.1 and 0.2 J/cm2, respectively. Subsurface impurities are the primary source of particles, and particle adhesion density is related to surface roughness. Pollution particle generation and splashing processes include temperature increases, phase changes, impact diffusion, and adhesion. The results provide a reference for the normal operation of high-energy laser systems. The results also suggest that the laser irradiation pretreatment of aluminum alloy surfaces is essential to improve the cleanliness level.

Surface molecular structure defects and laser-induced damage threshold of fused silica during a manufacturing process.

Laser induced damage of fused silica is a serious problem for high power laser systems, and damage precursors are mainly induced by manufacturing processes. In this work, fused silica samples were prepared from a manufacturing process including grinding, polishing and etching procedures. The chemical disorder of the prepared samples was inspected by using fluorescence microscopy and ultra-violet fluorescence spectrometer. The physical disorder was characterized by using Infrared and Raman spectrometer. Laser induced damage thresholds (LIDTs) were measured in R-on-1 mode by 355 nm 6.4 ns laser pulse. Results showed that with the manufacturing processes transforming from grinding to etching, the magnitude of fluorescence point defects reduced while their types did not change, the Si-O-Si bonds of prepared samples were strained and the strained bonds were mitigated. The LIDTs increased with the reducing of fluorescence defects and strained Si-O-Si bonds. However, these structural defects can not be eliminated by the current manufacturing process. Improvements may be needed to eliminate the structural defects for a higher LIDT of fused silica.