Thermal breakdown of ZnTe nanowires.

As the applications for inorganic nanowires continuously grow, studies on the stability of these structures under high electrical/thermal stress conditions are needed. ZnTe nanowires are grown by the vapor-liquid-solid technique and their breakdown under Joule heating is studied through in situ monitoring in a transmission electron microscope (TEM). The experimental setup, consisting of a scanning tunneling microscope (STM) and a movable piezotube inside the TEM, allows the manipulation of a single nanowire. A voltage applied to the STM tip in contact with a ZnTe nanowire leads to the breakdown of the nanowire into Zn and Te particles or balls which is observed in real time. These balls grow by Ostwald ripening, rendering the surface morphology of the ZnTe nanowire progressively rough. Diffraction patterns along the stem of the wire after the partial breakdown showed substantially smaller lattice spacing compared to 0.35 nm for pristine ZnTe nanowires.

Field emission and strain engineering of electronic properties in boron nitride nanotubes.

The electrical properties of boron nitride (BN) nanostructures, particularly BN nanotubes (NTs), have been studied less in comparison to the counterpart carbon nanotubes. The present work investigates the field emission (FE) behavior of BNNTs under multiple cycles of FE experiments and demonstrates a strain-engineering pathway to tune the electronic properties of BNNTs. The electrical probing of individual BNNTs were conducted inside a transmission electron microscope (TEM) using an in situ electrical holder capable of applying a bias voltage of up to 110 V. Our results indicate that in the first cycle a single BNNT can exhibit the current density of ∼1 mA cm(-2) at 110 V and the turn-on voltage of 325 V µm(-1). However, field emission properties reduced considerably in subsequent cycles. Real-time imaging revealed the structural degradation of individual BNNTs during FE experiments. The electromechanical measurements show that the conductivity of BNNTs can be tuned by means of mechanical straining. The resistance of individual BNNTs reduced from 2000 to 769 MΩ and the carrier concentration increased from 0.35 × 10(17) to 1.1 × 10(17) cm(-3) by straining the samples up to 2.5%.

In situ observation of reversible rippling in multi-walled boron nitride nanotubes.

The recent observation of high flexibility in buckled boron nitride nanotubes (BNNTs) contradicts the pre-existing belief about BN nanotube brittleness due to the partially ionic character of bonding between the B and N atoms. However, the underlying mechanisms and relationships within the nanotube remained unexplored. This study reports for the first time the buckling mechanism in multi-walled BNNTs upon severe mechanical deformation. Individual BNNTs were deformed inside a transmission electron microscope (TEM) equipped with an in situ atomic force microscopy holder. High-resolution TEM images revealed that bent BNNTs form multiple rippling upon buckling. The critical strain to form the first ripple was measured as 4.1% and the buckling process was reversible up to 26% strain. As opposed to carbon nanotubes, the BNNTs buckled into V-shaped ripples rather than smooth wavy shapes. The rippling wavelength was quantified in terms of the outer diameter and thickness of the nanotubes. The BNNTs showed a larger rippling wavelength compared to that of CNTs with the same number of walls. This difference was explained by the tendency of BN structures to reduce the number of thermodynamically unfavorable B-B and N-N bonds at the sharp corners in the rippling regions. The BNNTs' structure also exhibited a higher fracture strain compared to their counterpart.

In situ observation of morphological change in CdTe nano- and submicron wires.

We report growth and characterization of CdTe wires 30­400 nm in diameter by the vapor­liquid­solid technique. Individual nanowires were placed on a movable piezotube, which allowed three-dimensional motion toward a scanning tunneling microscope (STM). A bias was applied to the STM tip in contact with the nanowire, and the morphological changes due to Joule heating were observed in situ using a transmission electron microscope (TEM) in real time. For thick CdTe wires (d > ~150 nm), the process results in the growth of superfine nanowires (SFNWs) of 2­4 nm diameter on the surface of the wire. Smaller diameter nanowires, in contrast, disintegrate under the applied bias before the complete evolution of SFNWs on the surface.

A Lithium-Sulfur Battery using a 2D Current Collector Architecture with a Large-Sized Sulfur Host Operated under High Areal Loading and Low E/S Ratio.

While backless freestanding 3D electrode architectures for batteries with high loading sulfur have flourished in the recent years, the more traditional and industrially turnkey 2D architecture has not received the same amount of attention. This work reports a spray-dried sulfur composite with large intrinsic internal pores, ensuring adequate local electrolyte availability. This material offers good performance with a electrolyte content of 7 µL mg-1 at high areal loadings (5-8 mg cm-2 ), while also offering the first reported 2.8 µL mg-1 (8 mg cm-2 ) to enter into the second plateau of discharge and continue to operate for 20 cycles. Moreover, evidence is provided that the high-frequency semicircle (i.e., interfacial resistance) is mainly responsible for the often observed bypassing of the second plateau in lean electrolyte discharges.

Atomic-scale observation of lithiation reaction front in nanoscale SnO2 materials.

In the present work, taking advantage of aberration-corrected scanning transmission electron microscopy, we show that the dynamic lithiation process of anode materials can be revealed in an unprecedented resolution. Atomically resolved imaging of the lithiation process in SnO2 nanowires illustrated that the movement, reaction, and generation of b = [1[overline]1[overline]1] mixed dislocations leading the lithiated stripes effectively facilitated lithium-ion insertion into the crystalline interior. The geometric phase analysis and density functional theory simulations indicated that lithium ions initial preference to diffuse along the [001] direction in the {200} planes of SnO2 nanowires introduced the lattice expansion and such dislocation behaviors. At the later stages of lithiation, the Li-induced amorphization of rutile SnO2 and the formation of crystalline Sn and LixSn particles in the Li2O matrix were observed.

A computational and experimental investigation of the mechanical properties of single ZnTe nanowires.

One-dimensional nanostructures such as ZnTe, CdTe, Bi(2)Te(3) and others have attracted much attention in recent years for their potential in thermoelectric devices among other applications. A better understanding of their mechanical properties is important for the design of devices. A combined experimental and computational approach has been used here to investigate the size effects on the Young's modulus of ZnTe nanowires (NWs). The mechanical properties of individual ZnTe nanowires in a wide diameter range (50-230 nm) were experimentally measured inside a high resolution transmission electron microscope using an atomic force microscope probe with the ability to record in situ continuous force-displacement curves. The in situ observations showed that ZnTe NWs are flexible nanostructures with the ability to withstand relatively high buckling forces without becoming fractured. The Young's modulus is found to be independent of nanowire diameter in the investigated range, in contrast to reported results for ZnO NWs and carbon nanotubes where the modulus increases with a decrease in diameter. Molecular dynamics simulations performed for nanowires with diameters less than 20 nm show limited size dependence for diameters smaller than 5 nm. The surface atoms present lower Young's modulus according to the simulations and the limited size dependency of the cylindrical ZnTe NWs is attributed to the short range covalent interactions.

In situ electrochemical lithiation/delithiation observation of individual amorphous Si nanorods.

In situ electrochemical lithiation and delithiation processes inside a nanobattery consisting of an individual amorphous Si nanorod and ionic liquid were explored. Direct formation of the crystalline Li(22)Si(5) phase due to the intercalation of Li ions was observed. In addition, the role of the electrolyte-nanorod interface was examined. It was observed that the lithiation of Si nanorods is dominated by surface diffusion. Upon the delithiation process, partial decomposition of Li(22)Si(5) particles was observed which can explain the irreversible capacity loss that is generally seen in Si anodes. This study shows that the radial straining due to lithiation does not cause cracking in nanorods as small in diameter as 26 nm, whereas cracks were observed during the lithiation of 55 nm Si nanorods.

Chemical and nanomechanical analysis of rice husk modified by ATRP-grafted oligomer.

Rice husk (RH), an abundant agricultural residue, was reacted with 2-bromoisobutyryl bromide, to convert it to a heterogeneous polyfunctional macroinitiator for Atom Transfer Radical Polymerization (ATRP). The number of active sites placed on the RH surface was small, but they were ATRP active. Non-polar methyl methacrylate (MMA) and polar acrylonitrile (AN) were polymerized from the RH, and a sequential monomer addition was used to prepare an amphiphilic PMMA-b-PAN copolymer on RH surface. FTIR qualitatively confirmed the grafting. Gravimetric and XPS analysis of the different RH surface compositions indicated thin layers of oligomeric PMMA, PAN, and PMMA-b-PAN. The modified surfaces were mapped by nanomechanical AFM to measure surface roughness, and adhesion and moduli using the Derjaguin-Muller-Toropov model. RH grafted with MMA possessed a roughness value of 7.92, and a hard and weakly adhering surface (13.1 GPa and 16.7 nN respectively) while RH grafted with AN yielded a roughness value of 29 with hardness and adhesion values of 4.0 GPa and 23.5 nN. The PMMA-b-PAN modification afforded a surface with a roughness value of 51.5 nm, with hardness and adhesion values of 3.0 GPa and 75.3 nN.

Direct compressive measurements of individual titanium dioxide nanotubes.

The mechanical compressive properties of individual thin-wall and thick-wall TiO(2) nanotubes were directly measured for the first time. Nanotubes with outside diameters of 75 and 110 nm and wall thicknesses of 5 and 15 nm, respectively, were axially compressed inside a 400 keV high-resolution transmission electron microscope (TEM) using a new fully integrated TEM-atomic force microscope (AFM) piezo-driven fixture for continuous recording of the force-displacement curves. Individual nanotubes were directly subjected to compressive loading. We found that the Young's modulus of titanium dioxide nanotubes depended on the diameter and wall thickness of the nanotube and is in the range of 23-44 GPa. The thin-wall nanotubes collapsed at approximately 1.0 to 1.2 microN during axial compression.