RESUMO
A facile coagglomeration method for preparing a long alkyl chain modified graphene oxide (MGO)/MgCl2-supported Ti-based Ziegler-Natta catalyst was reported. The effects of MGO on the catalyst morphology and activity for ethylene polymerization were examined. The resultant polyethylene (PE)/MGO nanocomposites exhibited a layered morphology, with the MGO fillers being well dispersed and exhibiting strong interfacial adhesion to the PE matrix. The thermal stability and mechanical properties of the PE were significantly enhanced with the introduction of a small amount of the MGO filler. Thus, this work provides a facile approach to the production of high-performance PE.
RESUMO
In the present article, a novel spherical starch-supported vanadium (V)-based Ziegler-Natta catalyst was synthesized. The active centers of the obtained catalyst well dispersed in the starch through the SEM-EDX analysis. The effects of reaction conditions on ethylene polymerization were studied. The synthesized catalyst exhibited high activity toward ethylene polymerization in the presence of ethylaluminium sesquichloride (EASC) cocatalyst. Interestingly, the fiber shape PE was obtained directly during the polymerization process.
RESUMO
Rammed earth in a built environment has vapor diffusion characteristics and humidity control abilities, each of which is respectively attributed to the porous structures and the hydrophilic properties. Indeed, these structures and properties allow for the easy absorbance of water particles, hence affecting the durability of a rammed earth wall. This paper presents the water-repellency method for rammed earth walls, which utilizes siloxane copolymers containing fluorine. The water-repellent properties are investigated by measuring the contact angle, water absorption rate, and compressive strength after spray-coating with the synthesized siloxane copolymers on the surface of the rammed earth specimens under study. The water contact angle of the specimen, coated with a siloxane copolymer containing 10 mol.% of a silane monomer with a fluorine group, is about 140°. The water absorption of the specimen obtained after immersing in water for 24 h is low, at about 3.5 wt.%. In addition, the compressive strength remains more than 80% of the corresponding strength of the specimen which is not immersed in water. It is confirmed that the use of a 10% by volume of the siloxane copolymer containing the fluorine group may enhance the water-repellent performance and economic competitiveness.
RESUMO
Solar-driven water vaporization is considered one of the most sustainable ways to solve water scarcity. The design of highly efficient solar absorber systems has received extensive attention. Here, we report a novel light absorption material for water evaporation using laser-treated wood. The obtained laser-treated wood possesses interconnected 3D porous networks formed by the random construction of carbon arrays and a hydrophilic surface due to the oxygen implantation by laser treatment. When under 1 sun solar-simulated light irradiation (1 kW m-2), the surface temperatures of dry and water-saturated wood reach 59.5 °C and 40.4 °C, respectively, indicating good heat localization. As a result, the laser-treated wood under 1 sun illumination shows high solar to vapor efficiencies of 93.1% and 92.6% for pure water and seawater, respectively, which are higher than that of most wood-based reported photo-thermal conversion materials. Therefore, the fabricated laser-treated wood may pave the way for harvesting solar energy to produce clean water at low cost.
RESUMO
This paper presents findings obtained by evaluating the compressive strength, thermal conductivity, and durability of sand cylinder specimens stabilized with either epoxy emulsion (EM), acrylic polymer aqueous solution (APAS), EM-APAS mixture, or EM-APAS-lime mixture. Given the data obtained from the laboratory test, simulation analysis that uses a heat transfer fluid model of a ground-coupled heat pump (GCHP) system confirms the EM-APAS-lime binder performs best in the compressive strength and thermal conductivity; EM-APAS mixture performs best in the durability. However, the slake durability index of specimens containing EM-APAS-lime is equal to or greater than 80%. In addition, the compressive strength of sand stabilized with the EM-APAS-lime mixture is more than three times that of sand stabilized with cement. The thermal conductivity of sand stabilized with cement and that of sand treated with EM-APAS-lime mixture are 0.1 W/m·K and 0.9-1 W/m·K, respectively. It is confirmed that the heat collection of sand stabilized with EM-APAS-lime outperforms five times over that of sand stabilized with cement. These findings provide admissible evidence that the EM-APAS-lime mixture, which outperforms cement in compressive strength and thermal conductivity, is most suitable for ground improvement binder for GCHP systems.
RESUMO
Fluorescent image patterns of a substituted acetylene polymer film with a large FFV were successfully obtained by a µCP method using several kinds of chemical ink compounds. PO and SCA generated positive-type fluorescent image patterns. On the other hand, an ethanolic solution of DNT generated a negative-type fluorescent image pattern due to a significant quenching effect. An NMP solution of NR gave a two-color image pattern due to an intermolecular energy transfer from PTMSDPA to NR.
Assuntos
Impressão Molecular/métodos , Polímeros/síntese química , Cor , Fluorescência , Tinta , Microscopia de Fluorescência , Impressão Molecular/instrumentação , Estrutura Molecular , Polímeros/química , PorosidadeRESUMO
Electrospinning has recently emerged as a leading technique for the formation of nanofibrous structures made of organic and inorganic components. In this study, nanofibrous scaffolds were prepared by electrospining a bend solution of poly(L-lactide-co-glycolide) (PLGA) and silver nanoparticles in 1,1,1,3,3,3,-hexafluoro-2-propanol (HFIP). The resulting fibers ranged from 420 to 590 nm in diameter. To evaluate the possibility of using silver-containing PLGA as a tissue engineering scaffold, experiments on cell viability and antibacterial activity were carried out. As a result, PLGA nanofibrous scaffolds having silver nanoparticles of more than 0.5 wt% showed antibacterial effect against Staphylococcus aureus and Klebsiella pneumonia. Furthermore, silver-containing PLGA nanofibrous scaffolds showed viability, indicating their possible application in the field of tissue engineering.
Assuntos
Antibacterianos/química , Ácido Láctico/química , Nanofibras/química , Ácido Poliglicólico/química , Prata/química , Alicerces Teciduais , Animais , Antibacterianos/farmacologia , Processos de Crescimento Celular/efeitos dos fármacos , Sobrevivência Celular/efeitos dos fármacos , Klebsiella pneumoniae/efeitos dos fármacos , Ácido Láctico/farmacologia , Teste de Materiais , Nanopartículas Metálicas/química , Camundongos , Testes de Sensibilidade Microbiana , Microscopia Eletrônica de Varredura , Microscopia de Fluorescência , Células NIH 3T3 , Nanofibras/ultraestrutura , Tamanho da Partícula , Ácido Poliglicólico/farmacologia , Copolímero de Ácido Poliláctico e Ácido Poliglicólico , Prata/farmacologia , Staphylococcus aureus/efeitos dos fármacosRESUMO
The use of nontraditional soil stabilizers increases. Various new soil binding agents are under study to augment renewability and sustainability of an earth structure. However, despite increasing interest involved in red clay, there is minimal research investigating the stabilizing red clay with polymer. This paper presents the findings obtained by applying the acrylic polymer and epoxy emulsion as binding agent for red clay and that for sand. The epoxy-hardener ratio, amount of epoxy emulsion, and amount of polymer aqueous solution were manipulated to quantify their effects on red clay and sand, respectively. After compacting a pair of cylindrical samples of which diameter and height are 5 cm and 10 cm, respectively, it is cured for 3 and 7 days in a controlled condition. Each pair is produced to represent the engineering performance at each data point in the solution space. An optimal composition of the binding agents for red clay and that for sand mixture are identified by experimenting every data point. In addition, given lime into each sample, the maximum unconfined compressive strength (UCS) endured by red clay sample and that by sand sample are 2243 and 1493 kPa, respectively. The UCS obtained by the sample mixed with clay and sand reaches 2671 kPa after seven days of curing. It confirms that the addition of lime remarkably improves the UCS. When the clay-sand mixture, of which the ratio is 70:30, includes 5% lime, the UCS of the mixture outperforms. Indeed, these findings, i.e., the optimal proportion of components, may contribute to the increase of initial and long-term strength of an earth structure, hence improving the renewability and sustainability of the earth construction method.
RESUMO
Existing rammed earth construction methods have disadvantages such as increased initial costs for manufacturing the large formwork and increased labor costs owing to the labor-intensive construction techniques involved. To address the limitations of the existing rammed earth construction methods, an autonomous rammed earth construction method was introduced herein. When constructing an autonomous rammed-earth construction method, an alternative means of assuring the performance at the initial age of the binder in terms of materials is needed. In this study, in order to satisfy the performance of the red clay binder, epoxy emulsion was added to analyze the compressive strength, water loosening, shrinkage, rate of mass change, and microstructure in the range of the initial age. As a result of the analysis, the applicability of the epoxy emulsion was confirmed as a new additive for application to an autonomous rammed-earth construction method.
RESUMO
The polymerizable reduced graphene oxide (mRGO) grafted styrene-acrylonitrile copolymer composites were prepared via free radical polymerization. The graphene oxide (GO) and reduced graphene oxide (rGO) was reacted with 3-(tri-methoxysilyl)propylmethacrylate (MPS) and used as monomer to graft styrene and acrylonitrile on its surface. The successful modification and reduction of GO was confirmed using Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analyzer (TGA), Raman and X-ray diffraction (XRD). The mRGO was prepared using chemical and solvothermal reduction methods. The effect of the reduction method on the composite properties and nanosheet distribution in the polymer matrix was studied. The thermal stability, electrical conductivity and morphology of nanocomposites were studied. The electrical conductivity of the obtained nanocomposite was very high at 0.7 S/m. This facile free radical polymerization provides a convenient route to achieve excellent dispersion and electrically conductive polymers.
RESUMO
In this study, the performance evaluation was performed by adding a polymer aqueous (PA) solution as a new additive of the red clay binder for use in the rammed-earth construction method. The evaluation items were compressive strength, water erosion, shrinkage, crystal structure, and microstructure. As a result of the experiment, the binder was improved by efficiently bonding the silica particles by the polymerized polymer. It was confirmed that adding a PA solution to red clay enhances the compressive strength, which is further improved when 5 wt% poly(Acrylic acid(AA)-co-Acrylamide(AM)) is added to the PA solution. Microstructural analysis indicated that the addition of a PA solution facilitates effective bonding of the silica particles of red clay to form hydrogen bonding with poly(AA-co-AM) and encourages aggregate formation. Therefore, the study confirmed that PA solution can be applied to satisfy the performance requirements of the rammed-earth construction by improving the durability and strength of the binder.
RESUMO
In this work, a melamine functionalized molybdenum disulfide (M-MoS2) was prepared and used as fillers to form epoxy (EP)/MoS2 nanocomposites. The effects of molybdenum disulfide (MoS2) and melamine functionalized molybdenum disulfide (M-MoS2) loading on the mechanical properties of epoxy composites were investigated and compared. With only addition of 0.8 wt% M-MoS2, the tensile strength and modulus of EP/M-MoS2 nanocomposites showed 4.5 and 4.0 times increase over the neat epoxy. Interestingly, the elongation at break value of EP was also increased with the introduction of M-MoS2 fillers. These properties could result from the good dispersion and strong interfacial adhesion of M-MoS2 fillers and the EP matrix. Therefore, this work provides a facile way to produce of high-performance EP nanocomposites.
RESUMO
In this research, a Zieglerâ»Natta catalyst intercalated MoS2 was synthesized through the intercalation of a Grignard reagent into MoS2 galleries, followed by the anchoring of TiCl4. During propylene polymerization, the intercalated MoS2 exfoliated in situ to form PP/exfoliated MoS2 (EMoS2) nanocomposites. The isotactic index values of the resultant PP/EMoS2 nanocomposites were as high as 99%, varying from 98.1% to 99.0%. It was found that the incorporation of the EMoS2 significantly improved the thermal stability and mechanical properties (tensile strength, modulus, and elongation at break) of PP. After introduction of EMoS2, the maximum increases in Td5% and Tdmax were 36.9 and 9.7 °C, respectively, relative to neat PP. After blending with commercial PP, the resultant nanocomposites increase in tensile strength and modulus up to 11.4% and 61.2% after 0.52 wt % EMoS2 loading. Thus, this work provides a new way to produce high-performance PP.
RESUMO
A novel well-defined amphiphilic Core-Shell star-block copolymer was synthesized from trimethylolpropane, ε-caprolactone, and glycidyl methacrylate by a combination of enzymatic ring-opening polymerization and atom transfer radical polymerization. The structure and molecular weight of the macroinitiator and the star-block copolymer were confirmed by means of nuclear magnetic resonance and gel permeation chromatography. The effects of the glycidyl methacrylate sequence length on the hydrodynamic diameter and morphology of the polymer micelles were investigated by dynamic light scattering and transmission electron microscopy, respectively.
RESUMO
A practical optical backplane system was prepared with transmitter-receiver processing boards and an optical backplane made from polymeric-waveguide-embedded optical printed-circuit boards. Optical slots were used as connection components between the transmitter-receiver processing boards and the backplane board to permit easy and repeatable insertion and extraction of the boards with micrometer precision. We report 10 Gbit/s data transmission between an optical backplane and the transmitter-receiver processing boards.