Deterministic Lateral Displacement Using Hexagonally Arranged, Bottom-Up-Inspired Micropost Arrays.

Size-based separation of particles in microfluidic devices can be achieved using arrays of micro- or nanoscale posts using a technique known as deterministic lateral displacement (DLD). To date, DLD arrays have been limited to parallelogram or rotated-square arrangements of posts, with various post shapes having been explored in these two principal arrangements. This work examines a new DLD geometry based on patterning obtainable through self-assembly of single-layer nanospheres, which we call hexagonally arranged triangle (HAT) geometry. Finite element simulations are used to characterize the DLD separation properties of the HAT geometry. The relationship between the array angle, the gap spacing, and the critical diameter for separation is derived for the HAT geometry and expressed in a similar mathematical form as conventional parallelogram and rotated-square DLD arrays. At array angles <7°, HAT structures demonstrate smaller particle sorting capability (smaller critical diameter-to-gap spacing ratio) compared to published experimental results for parallelogram-type DLD arrays with circular posts. Experimental validation of DLD separation confirms the separation ability of the HAT array geometry. It is envisioned that this work will provide the first step toward future implementation of nanoscale DLD arrays fabricated by low-cost, bottom-up self-assembly approaches.

Correction: Direct laser writing-enabled 3D printing strategies for microfluidic applications.

Correction for 'Direct laser writing-enabled 3D printing strategies for microfluidic applications' by Olivia M. Young et al., Lab Chip, 2024, DOI: https://doi.org/10.1039/D3LC00743J.

Direct laser writing-enabled 3D printing strategies for microfluidic applications.

Over the past decade, additive manufacturing-or "three-dimensional (3D) printing"-has attracted increasing attention in the Lab on a Chip community as a pathway to achieve sophisticated system architectures that are difficult or infeasible to fabricate via conventional means. One particularly promising 3D manufacturing technology is "direct laser writing (DLW)", which leverages two-photon (or multi-photon) polymerization (2PP) phenomena to enable high geometric versatility, print speeds, and precision at length scales down to the 100 nm range. Although researchers have demonstrated the potential of using DLW for microfluidic applications ranging from organ on a chip and drug delivery to micro/nanoparticle processing and soft microrobotics, such scenarios present unique challenges for DLW. Specifically, microfluidic systems typically require macro-to-micro fluidic interfaces (e.g., inlet and outlet ports) to facilitate fluidic loading, control, and retrieval operations; however, DLW-based 3D printing relies on a micron-to-submicron-sized 2PP volume element (i.e., "voxel") that is poorly suited for manufacturing these larger-scale fluidic interfaces. In this Tutorial Review, we highlight and discuss the four most prominent strategies that researchers have developed to circumvent this trade-off and realize macro-to-micro interfaces for DLW-enabled microfluidic components and systems. In addition, we consider the possibility that-with the advent of next-generation commercial DLW printers equipped with new dynamic voxel tuning, print field, and laser power capabilities-the overall utility of DLW strategies for Lab on a Chip fields may soon expand dramatically.

A 3D-MICROPRINTED COAXIAL NOZZLE FOR FABRICATING LONG, FLEXIBLE MICROFLUIDIC TUBING.

A variety of emerging applications, particularly those in medical and soft robotics fields, are predicated on the ability to fabricate long, flexible meso/microfluidic tubing with high customization. To address this need, here we present a hybrid additive manufacturing (or "three-dimensional (3D) printing") strategy that involves three key steps: (i) using the "Vat Photopolymerization (VPP) technique, "Liquid-Crystal Display (LCD)" 3D printing to print a bulk microfluidic device with three inlets and three concentric outlets; (ii) using "Two-Photon Direct Laser Writing (DLW)" to 3D microprint a coaxial nozzle directly atop the concentric outlets of the bulk microdevice, and then (iii) extruding paraffin oil and a liquid-phase photocurable resin through the coaxial nozzle and into a polydimethylsiloxane (PDMS) channel for UV exposure, ultimately producing the desired tubing. In addition to fabricating the resulting tubing-composed of polymerized photomaterial-at arbitrary lengths (e.g., > 10 cm), the distinct input pressures can be adjusted to tune the inner diameter (ID) and outer diameter (OD) of the fabricated tubing. For example, experimental results revealed that increasing the driving pressure of the liquid-phase photomaterial from 50 kPa to 100 kPa led to fluidic tubing with IDs and ODs of 291±99 µm and 546±76 µm up to 741±31 µm and 888±39 µm, respectively. Furthermore, preliminary results for DLW-printing a microfluidic "M" structure directly atop the tubing suggest that the tubing could be used for "ex situ DLW (esDLW)" fabrication, which would further enhance the utility of the tubing.

FABRICATION OF MULTILUMEN MICROFLUIDIC TUBING FOR EX SITU DIRECT LASER WRITING.

Among the numerous additive manufacturing or "three-dimensional (3D) printing" techniques, two-photon Direct Laser Writing (DLW) is distinctively suited for applications that demand high geometric versatility with micron-to-submicron-scale feature resolutions. Recently, "ex situ DLW (esDLW)" has emerged as a powerful approach for printing 3D microfluidic structures directly atop meso/macroscale fluidic tubing that can be manipulated by hand; however, difficulties in creating custom esDLW-compatible multilumen tubing at such scales has hindered progress. To address this impediment, here we introduce a novel methodology for fabricating submillimeter multilumen tubing for esDLW 3D printing. Preliminary fabrication results demonstrate the utility of the presented strategy for resolving 743 µm-in-diameter tubing with three lumens-each with an inner diameter (ID) of 80 µm. Experimental results not only revealed independent flow of discrete fluorescently labelled fluids through each of the three lumens, but also effective esDLW-printing of a demonstrative 3D "MEMS" microstructure atop the tubing. These results suggest that the presented approach could offer a promising pathway to enable geometrically sophisticated microfluidic systems to be 3D printed with input and/or output ports fully sealed to multiple, distinct lumens of fluidic tubing for emerging applications in fields ranging from drug delivery and medical diagnostics to soft surgical robotics.