Evaluation of hygrothermal performance of wood-derived biocomposite with biochar in response to climate change.

Wood is a sustainable resource and building material. It provides an excellent response to climate change and has excellent insulation performance. However, structural defects may occur due to decay from moisture, resulting in poor dimensional stability. The rich organic substances contained in wood can lead to mold when the moisture content is consistently high, adversely affecting the health of occupants. Therefore, we attempted to compensate for the disadvantages of wood in regard to water stability while maintaining the high thermal insulation performance and carbon dioxide storage capacity, using biochar from thermally decomposed spruce under oxygen limiting conditions. A wood-derived biocomposite was prepared by mixing biochar and soft wood-based chips using the hot-press method, and the thermal conductivity, specific heat, water vapor resistance factor, moisture adsorption, and moisture desorption performances were analyzed. The thermal conductivity of WB10 with 10 wt% biochar content was 0.09301 W/mK. This is a 7.98% decrease from 0.10108 W/mK, the thermal conductivity of WB0 without biochar. The water vapor resistance factor tended to increase when the biochar ratio increased. As the proportion of biochar increased, the equilibrium moisture content in high relative humidity tended to decrease, and it was found that the moisture adsorption and desorption performances were affected by the ratio of the biochar. Therefore, wood-derived biocomposites using biochar can be used in environmentally friendly materials, with improved thermal insulation performance and water stability.

Innovative building materials by upcycling clothing waste into thermal energy storage matrix with phase change materials.

The current volume of clothing waste reached 115 million tons in 2021 and is projected to increase to approximately 150 million tons by 2030. This significant surge in clothing waste has prompted heightened discussions regarding environmentally friendly recycling methods. Clothing presents complex properties, posing substantial challenges to recycling and usually resulting in environmental pollution when disposed. In this study, our recycling approach capitalizes on the differing melting points of textiles. This transformation was achieved through a physical process that included an opening procedure and high temperature heat compression. Textile materials exhibit exceptional thermal properties. Through experimentation on 50 g fiber specimens, thermal conductivities similar to commercial insulation materials were observed, registering an average of 0.0592 W/m·K at 20 °C and 0.06053 W/m·K at 40 °C. This study explores the impregnation of phase change materials (PCMs) into clothing waste-based specimens, equipping them with heat storage capabilities. During the experimental phase, we employed three distinct types of PCMs to evaluate their thermal properties and heat storage capacities in relation to their respective melting temperatures. Through thermal properties analysis, we determined the latent heat capacity of each specimen, ranging from a minimum of 6.63 J/g to a maximum of 75.81 J/g. Our observations indicated a reduction in peak temperature and time-leg effects attributable to the use of PCMs for surface heat flow. This research underscores the superior thermal performance of construction and building materials derived from clothing waste, enhanced by the integration of PCMs, when compared to traditional materials and other waste-derived alternatives.

Evaluation of particle generation due to deterioration of flooring in schools.

Particulate matter is harmful to humans. An important indoor source of such particles is the deterioration of floor materials brought about by occupants walking. Accordingly, an experiment was conducted to simulate the deterioration of floor material spacing. Considering a school schedule with repeated semesters and vacations, the experiment was conducted by repeating heat-and-rest cycles. Similar results were obtained for particle emission rates under each condition during the first and second deterioration periods. The PVC tiles generated more particles under aged conditions than under non-aged conditions, whereas the wood generated fewer particles under aged conditions. In addition to the quantitative results, a study was conducted on the characteristics of the generated particles, and the particulate matter found in plastic was confirmed in the PVC tiles. Schools where children are present for more than 6 h a day may be exposed to more particulate matter. Therefore, replacing plastic-based materials with eco-friendly building materials is expected to have long-term health benefits for children.

Passive PM2.5 control plan of educational buildings by using airtight improvement technologies in South Korea.

Modern people spend most of their time indoors. Therefore, controlling indoor air quality is one of the most important factors for health. The indoor fine dust concentration is affected by the outdoor fine dust concentration. When the latter is high, it increases due to immersion. Therefore, improving the sealing performance of a building is an effective strategy to reduce indoor fine dust concentration during periods of severe outdoor fine dust without considering indoor fine dust generating factors. Traditional methods of improving the airtightness of a building have focused on replacing windows or doors. However, for reasons such as constructability and economic feasibility, more diverse technologies need to be considered. Due to this necessity, this study applied technologies such as sealing film, sealing lid, and padding to the educational building, and then derived the airtight performance through the blower door experiment, and measured the fine dust concentration to evaluate the effect. As a result of the experiment, it was analyzed that air leakage was reduced by up to 37% and fine dust by 22%.

Microplastic: A particulate matter(PM) generated by deterioration of building materials.

Particulate matter (PM), an inhalable material, is generated from various sources, including building materials. To maintain indoor air quality, it is necessary to analyze harmful substances and establish a method for their remediation. The purpose of this study is to identify the particles generated during the deterioration of building materials and analyze the composition of fine dust particles with respect to the degree of deterioration. The concentration of particles generated was analyzed using an SPS30 PM sensor in the built chamber. PM10 and PM2.5 levels of the maximum of 41.95 mg/m3 and 20.63 mg/m3, respectively, were generated from the tested building materials. The components of the collected PM were carbon, hydrogen, and silicon, among others, which are high-molecular-weight compounds. Particles of size 2.5 µm or less were detected, and the possibility of generating nanoplastics was investigated.

Verification of particle matter generation due to deterioration of building materials as the cause of indoor fine dust.

Particles of fine dust are pollutants that adversely affect indoor air quality and exacerbate human respiratory diseases. The aging of the building was pointed out as a source of fine dust indoors. The aging of buildings has various causes of deterioration. During various deterioration, friction adversely affects the building floor finish. In this study, an accelerated friction deterioration device was used to confirm the generation of fine dust particles through the frictional deterioration of floor finishes in buildings. The study found that the concentration of fine dust particles attributed to deteriorating flooring was 327 mg/m3 in PM2.5 and 4828 mg/m3 in PM10 and confirmed that particle distribution differs depending on the surface of the flooring. Particles of 10 µm or less were observed through particle analysis. The study confirmed that fine dust particles did not diffuse in a specific direction and that the detected fine dust particles could be attributed to deterioration. Further research is needed on the detection of fine dust in degraded building finishing materials.