Data-based dynamic compartment model: Modeling of E. coli fed-batch fermentation in a 600 m3 bubble column.

Mathematical modeling is a powerful and inexpensive approach to provide a quantitative basis for improvements that minimize the negative effects of bioreactor heterogeneity. For a model to accurately represent a heterogeneous system, a flow model that describes how mass is channeled between different zones of the bioreactor volume is necessary. In this study, a previously developed compartment model approach based on data from flow-following sensor devices was further developed to account for dynamic changes in volume and flow rates and thus enabling simulation of the widely used fed-batch process. The application of the dynamic compartment model was demonstrated in a study of an industrial fermentation process in a 600 m3 bubble column bioreactor. The flow model was used to evaluate the mixing performance by means of tracer simulations and was coupled with reaction kinetics to simulate concentration gradients in the process. The simulations showed that despite the presence of long mixing times and significant substrate gradients early in the process, improving the heterogeneity did not lead to overall improvements in the process. Improvements could, however, be achieved by modifying the dextrose feeding profile.

Characterization of a novel lytic bacteriophage from an industrial Escherichia coli fermentation process and elimination of virulence using a heterologous CRISPR-Cas9 system.

Bacterial-bacteriophage interactions are a well-studied and ecologically-important aspect of microbiology. Many commercial fermentation processes are susceptible to bacteriophage infections due to the use of high-density, clonal cell populations. Lytic infections of bacterial cells in these fermentations are especially problematic due to their negative impacts on product quality, asset utilization, and fouling of downstream equipment. Here, we report the isolation and characterization of a novel lytic bacteriophage, referred to as bacteriophage DTL that is capable of rapid lytic infections of an Escherichia coli K12 strain used for commercial production of 1,3-propanediol (PDO). The bacteriophage genome was sequenced and annotated, which identified 67 potential open-reading frames (ORF). The tail fiber ORF, the largest in the genome, was most closely related to bacteriophage RTP, a T1-like bacteriophage reported from a commercial E. coli fermentation process in Germany. To eliminate virulence, both a fully functional Streptococcus thermophilus CRISPR3 plasmid and a customized S. thermophilus CRISPR3 plasmid with disabled spacer acquisition elements and seven spacers targeting the bacteriophage DTL genome were constructed. Both plasmids were separately integrated into a PDO production strain, which was subsequently infected with bacteriophage DTL. The native S. thermophilus CRISPR3 operon was shown to decrease phage susceptibility by approximately 96%, while the customized CRISPR3 operon provided complete resistance to bacteriophage DTL. The results indicate that the heterologous bacteriophage-resistance system described herein is useful in eliminating lytic infections of bacteriophage DTL, which was prevalent in environment surrounding the manufacturing facility.

Degradation and half-life of DNA present in biomass from a genetically-modified organism during land application.

White biotechnology has made a positive impact on the chemical industry by providing safer, more efficient chemical manufacturing processes that have reduced the use of toxic chemicals, harsh reaction conditions, and expensive metal catalysts, which has improved alignment with the principles of Green Chemistry. The genetically-modified (GM) biocatalysts that are utilized in these processes are typically separated from high-value products and then recycled, or eliminated. Elimination routes include disposal in sanitary landfills, incineration, use as a fuel, animal feed, or reuse as an agricultural soil amendment or other value-added products. Elimination routes that have the potential to impact the food chain or environment have been more heavily scrutinized for the fate and persistence of biological products. In this study, we developed and optimized a method for monitoring the degradation of strain-specific DNA markers from a genetically-modified organism (GMO) used for the commercial production of 1,3-propanediol. Laboratory and field tests showed that a marker for heterologous DNA in the GM organism was no longer detectable by end-point polymerase chain reaction (PCR) after 14 days. The half-life of heterologous DNA was increased by 17% (from 42.4 to 49.7 h) after sterilization of the soil from a field plot, which indicated that abiotic factors were important in degradation of DNA under field conditions. There was no evidence for horizontal transfer of DNA target sequences from the GMO to viable organisms present in the soil.

Recent advances in the biochemistry of spinosyns.

Spinosyn and its analogs, produced by Saccharopolyspora spinosa, are the active ingredients in a family of insect control agents. They are macrolides with a 21-carbon, 12-membered tetracyclic lactones that are attached to two deoxysugars, tri-O-methylrhamnose and forosamine. Labeling studies, analysis of the biosynthetically blocked mutants, and the genetic identification of the spinosyn gene cluster have provided detailed information concerning the mechanism of spinosyn biosynthesis and have enabled combinatorial biosynthesis of a large group of new spinosyns. The following developments have recently impacted the field of spinosyn biology: (1) A second-generation spinosyn called spinetoram (XDE-175) was launched in late 2007; it is a semisynthesized spinosyn derivative produced through the modification of 3'-O-methyl group of rhamnose and the double bond between C5 and C6 of spinosyn J and L. This molecule was shown to have improved insecticidal activity, enhanced duration of control, and an expanded pest spectrum. (2) A new class of spinosyns, the butenyl-spinosyns, was discovered from Saccharopolyspora pogona. The butenyl-spinosyns are similar to spinosyns, but differ in the length of the side chain at C-21. In addition to structural similarities with the spinosyns, the butenyl-spinosyns exhibit a high level of similarity in insecticidal activity to spinetoram. (3) Spinosyn analogs, 21-cyclobutyl-spinosyn A and 21-cyclobutyl-spinosyn D were generated by metabolic engineering of the spinosyn biosynthetic gene cluster. They showed better insecticidal activities against cotton aphid and tobacco budworm than that of spinosyn A and D. Future progress toward the development of more potent spinosad analogs, as well as enhancements in production yields will likely result from these recent advances in the genetics and biochemistry of spinosyns.

Effect of the presence of the antimicrobial tylosin in swine waste on anaerobic treatment.

An anaerobic sequencing batch reactor (ASBR), seeded with a biomass inoculum that previously had not been exposed to the macrolide antimicrobial tylosin (mixture of Tylosin A, B, C, and D), was operated for 3 months with swine waste without Tylosin A and for 9 months with swine waste containing Tylosin A at an average concentration of 1.6 mg/L. When swine waste with tylosin was fed to the ASBR, methane production and volatile solids removal did not appear to be inhibited and a methane yield of 0.47 L methane per gram volatile solids fed to the ASBR was observed. Throughout the operating period, Tylosin A levels in ASBR biomass and effluent were below the detection limit of 0.01 mg/L. However, during the first 3 months of operation, the levels of macrolide-lincosamide-streptogramin B (MLSB)-resistant bacteria in the ASBR biomass increased substantially as determined by hybridizations with oligonucleotide probes designed to target MLSB-resistant bacteria. Since no Tylosin A was present in the swine waste during the initial 3 months, the presence of MLSB-resistant bacteria in the swine waste was likely the reason for the increase in resistance. Subsequently, the levels of MLSB-resistant bacteria in ASBR biomass stabilized with an average of 44.9% for the 9 months of operation with swine waste containing Tylosin A. The level of MLSB-resistant bacteria in the swine waste fed to the ASBR during this period averaged 18.0%. The results indicate that anaerobic treatment of a waste stream containing tylosin was effective (based on reactor performance) and that the level of resistant bacteria in the ASBR was substantially higher than in the waste stream fed to this system.

Bias of Tedlar bags in the measurement of agricultural odorants.

Odor regulations typically specify the use of dynamic dilution olfactometery (DDO) as a method to quantify odor emissions, and Tedlar bags are the preferred holding container for grab samples. This study was conducted to determine if Tedlar bags affect the integrity of sampled air from animal operations. Air samples were collected simultaneously in both Tedlar bags and Tenax thermal desorption tubes. Sample sources originated from either a hydrocarbon-free air tank, dynamic headspace chamber (DHC), or swine-production facility, and were analyzed by gas chromatography-mass spectrometry-olfactometry (GC-MS-O). Several background contaminants were identified from Tedlar bags, which included the odorous compounds N,N-dimethyl acetamide (DMAC), acetic acid, and phenol. Samples from the DHC demonstrated that recovery of malodor compounds was dependent on residence time in the Tedlar bag with longer residence time leading to lower recovery. After 24 h of storage, recovery of C3-C6 volatile fatty acids (VFA) averaged 64%, 4-methylphenol and 4-ethylphenol averaged 10%, and indole and 3-methylindole were below the detection limits of GC-MS-O. The odor activity value (OAV) of grab samples collected in Tedlar bags were 33 to 65% lower following 24 h of storage. These results indicate that significant odorant bias occurs when using Tedlar bags for the sampling of odors from animal production facilities.

Scaling up of renewable chemicals.

The transition of promising technologies for production of renewable chemicals from a laboratory scale to commercial scale is often difficult and expensive. As a result the timeframe estimated for commercialization is typically underestimated resulting in much slower penetration of these promising new methods and products into the chemical industries. The theme of 'sugar is the next oil' connects biological, chemical, and thermochemical conversions of renewable feedstocks to products that are drop-in replacements for petroleum derived chemicals or are new to market chemicals/materials. The latter typically offer a functionality advantage and can command higher prices that result in less severe scale-up challenges. However, for drop-in replacements, price is of paramount importance and competitive capital and operating expenditures are a prerequisite for success. Hence, scale-up of relevant technologies must be interfaced with effective and efficient management of both cell and steel factories. Details involved in all aspects of manufacturing, such as utilities, sterility, product recovery and purification, regulatory requirements, and emissions must be managed successfully.

Spectral and thermodynamic properties of methanobactin from γ-proteobacterial methane oxidizing bacteria: a case for copper competition on a molecular level.

Methanobactin (mb) is a low molecular mass copper-binding molecule analogous to iron-binding siderophores. The molecule is produced by many methanotrophic or methane oxidizing bacteria (MOB), but has only been characterized to date in one MOB, Methylosinus trichosporium OB3b. To explore the potential molecular diversity in this novel class of metal binding compound, the spectral (UV-visible, fluorescent, and electron paramagnetic resonance) and thermodynamic properties of mb from two γ-proteobacterial MOB, Methylococcus capsulatus Bath and Methylomicrobium album BG8, were determined and compared to the mb from the α-proteobacterial MOB, M. trichosporium OB3b. The mb from both γ-proteobacterial MOB differed from the mb from M. trichosporium OB3b in molecular mass and spectral properties. Compared to mb from M. trichosporium OB3b, the extracellular concentrations were low, as were copper-binding constants of mb from both γ-proteobacterial MOB. In addition, the mb from M. trichosporium OB3b removed Cu(I) from the mb of both γ-proteobacterial MOB. Taken together the results suggest mb may be a factor in regulating methanotrophic community structure in copper-limited environments.

Isolation, characterization, and ecology of sulfur-respiring crenarchaea inhabiting acid-sulfate-chloride-containing geothermal springs in Yellowstone National Park.

Elemental sulfur (S(0)) is associated with many geochemically diverse hot springs, yet little is known about the phylogeny, physiology, and ecology of the organisms involved in its cycling. Here we report the isolation, characterization, and ecology of two novel, S(0)-reducing Crenarchaea from an acid geothermal spring referred to as Dragon Spring. Isolate 18U65 grows optimally at 70 to 72 degrees C and at pH 2.5 to 3.0, while isolate 18D70 grows optimally at 81 degrees C and pH 3.0. Both isolates are chemoorganotrophs, dependent on complex peptide-containing carbon sources, S(0), and anaerobic conditions for respiration-dependent growth. Glycerol dialkyl glycerol tetraethers (GDGTs) containing four to six cyclopentyl rings were present in the lipid fraction of isolates 18U65 and 18D70. Physiological characterization suggests that the isolates are adapted to the physicochemical conditions of Dragon Spring and can utilize the natural organic matter in the spring as a carbon and energy source. Quantitative PCR analysis of 16S rRNA genes associated with the S(0) flocs recovered from several acid geothermal springs using isolate-specific primers indicates that these two populations together represent 17 to 37% of the floc-associated DNA. The physiological characteristics of isolates 18U65 and 18D70 are consistent with their potential widespread distribution and putative role in the cycling of sulfur in acid geothermal springs throughout the Yellowstone National Park geothermal complex. Based on phenotypic and genetic characterization, the designations Caldisphaera draconis sp. nov. and Acidilobus sulfurireducens sp. nov. are proposed for isolates 18U65 and 18D70, respectively.

Role of Rhodobacter sp. strain PS9, a purple non-sulfur photosynthetic bacterium isolated from an anaerobic swine waste lagoon, in odor remediation.

Temporal pigmentation changes resulting from the development of a purple color in anaerobic swine waste lagoons were investigated during a 4-year period. The major purple photosynthetic bacterium responsible for these color changes and the corresponding reductions in odor was isolated from nine photosynthetic lagoons. By using morphological, physiological, and phylogenetic characterization methods we identified the predominant photosynthetic bacterium as a new strain of Rhodobacter, designated Rhodobacter sp. strain PS9. Rhodobacter sp. strain PS9 is capable of photoorganotrophic growth on a variety of organic compounds, including all of the characteristic volatile organic compounds (VOC) responsible for the odor associated with swine production facilities (J. A. Zahn, A. A. DiSpirito, Y. S. Do, B. E. Brooks, E. E. Copper, and J. L. Hatfield, J. Environ. Qual. 30:624-634, 2001). The seasonal variations in airborne VOC emitted from waste lagoons showed that there was a 80 to 93% decrease in the concentration of VOC during a photosynthetic bloom. During the height of a bloom, the Rhodobacter sp. strain PS9 population accounted for 10% of the total community and up to 27% of the eubacterial community based on 16S ribosomal DNA signals. Additional observations based on seasonal variations in meteorological, biological, and chemical parameters suggested that the photosynthetic blooms of Rhodobacter sp. strain PS9 were correlated with lagoon water temperature and with the concentrations of sulfate and phosphate. In addition, the photosynthetic blooms of Rhodobacter sp. strain PS9 were inversely correlated with the concentrations of protein and fluoride.

The membrane-associated methane monooxygenase (pMMO) and pMMO-NADH:quinone oxidoreductase complex from Methylococcus capsulatus Bath.

Improvements in purification of membrane-associated methane monooxygenase (pMMO) have resulted in preparations of pMMO with activities more representative of physiological rates: i.e., >130 nmol.min(-1).mg of protein(-1). Altered culture and assay conditions, optimization of the detergent/protein ratio, and simplification of the purification procedure were responsible for the higher-activity preparations. Changes in the culture conditions focused on the rate of copper addition. To document the physiological events that occur during copper addition, cultures were initiated in medium with cells expressing soluble methane monooxygenase (sMMO) and then monitored for morphological changes, copper acquisition, fatty acid concentration, and pMMO and sMMO expression as the amended copper concentration was increased from 0 (approximately 0.3 microM) to 95 microM. The results demonstrate that copper not only regulates the metabolic switch between the two methane monooxygenases but also regulates the level of expression of the pMMO and the development of internal membranes. With respect to stabilization of cell-free pMMO activity, the highest cell-free pMMO activity was observed when copper addition exceeded maximal pMMO expression. Optimization of detergent/protein ratios and simplification of the purification procedure also contributed to the higher activity levels in purified pMMO preparations. Finally, the addition of the type 2 NADH:quinone oxidoreductase complex (NADH dehydrogenase [NDH]) from M. capsulatus Bath, along with NADH and duroquinol, to enzyme assays increased the activity of purified preparations. The NDH and NADH were added to maintain a high duroquinol/duroquinone ratio.