Preparation and Performance Study of SiC-Reinforced Fe-Based Wear-Resistant Composite Grinding Media.

During industrial and laboratory processes involving material grinding, the grinding media endure prolonged high-collision and friction environments, resulting in substantial wear. Consequently, this study adopts the hot-pressing sintering technique in powder metallurgy to prepare SiC-reinforced Fe-based wear-resistant composite grinding media, aiming to increase wear performance. For this purpose, Fe with 10 wt% SiC powders were milled for the fabrication of the composite. Then, sintering was performed by hot press at 1100 °C in a furnace. Scanning electron microscopy (SEM) and X-ray diffraction were employed to investigate the microstructures and phase of SiC-reinforced Fe-based matrix composite. Subsequently, comparative performance evaluations of the newly developed grinding media and traditional chromium-based media were conducted in terms of wear rate and grinding efficiency. The wear resistance tests revealed that the SiC-reinforced composite media displayed significantly superior wear resistance across various abrasives compared to the chromium-containing alternatives. Specifically, the composite media achieved a wear rate reduction of 2.9 times against standard sand over 1 h, and 2.3 and 2.4 times against sandstone and iron slag, respectively. Moreover, extended grinding for 3 hours further enhanced these reductions to 3.1, 2.4, and 2.7 times, respectively. Additionally, efficiency assessments indicated that at a 1:1 material ratio, the composite media outperformed the chromium-containing media in grinding efficiency by 7.5%, 12.5%, and 10.3% for standard sand, sandstone, and iron slag, respectively. Further increasing the material ratio to 3:1 resulted in efficiency improvements of 7.4%, 17.5%, and 11.3%, correspondingly.

Evaluation and Analysis of Cement Raw Meal Homogenization Characteristics Based on Simulated Equipment Models.

In recent years, the variability in the composition of cement raw materials has increasingly impacted the quality of cement products. However, there has been relatively little research on the homogenization effects of equipment in the cement production process. Existing studies mainly focus on the primary functions of equipment, such as the grinding efficiency of ball mills, the thermal decomposition in cyclone preheaters, and the thermal decomposition in rotary kilns. This study selected four typical pieces of equipment with significant homogenization functions for an in-depth investigation: ball mills, pneumatic homogenizing silos, cyclone preheaters, and rotary kilns. To assess the homogenization efficacy of each apparatus, scaled-down models of these devices were constructed and subjected to simulated experiments. To improve experimental efficiency and realistically simulate actual production conditions in a laboratory setting, this study used the uniformity of the electrical capacitance of mixed powders instead of compositional uniformity to analyze homogenization effects. The test material in the experiment consisted of a mixture of raw meal from a cement factory with a high dielectric constant and Fe3O4 powder. The parallel plate capacitance method was employed to ascertain the capacitance value of the mixed powder prior to and subsequent to treatment by each equipment model. The fluctuation of the input and output curves was analyzed, and the standard deviation (S), coefficient of variation (R), and homogenization multiplier (H) were calculated in order to evaluate the homogenization effect of each equipment model on the raw meal. The findings of the study indicated that the pneumatic homogenizer exhibited an exemplary homogenization effect, followed by the ball mill. For the ball mill, a higher proportion of small balls in the gradation can significantly enhance the homogenization effect without considering the grinding efficiency. The five-stage cyclone preheater also has a better homogenization effect, while the rotary kiln has a less significant homogenization effect on raw meal. Finally, the raw meal processed by each equipment model was used for clinker calcination and the preparation of cement mortar samples. After curing for three days, the compressive and flexural strengths of the samples were tested, thereby indirectly verifying the homogenization effect of each equipment model on the raw meal. This study helps to understand the homogenization process of raw materials by equipment in cement production and provides certain reference and data support for equipment selection, operation optimization, and quality control in the cement production process.

Research on Resource Recovery and Disposal of Copper-Containing Sludge.

Copper-containing sludge is a common by-product of industrial activities, particularly electroplating and metal processing. This type of sludge contains high concentrations of heavy metals such as copper, which can pose a potential threat to the environment. Therefore, its treatment and disposal require special attention. Due to its efficient mass and heat transfer characteristics, the suspended state technology has shown significant potential for application in a number of key processes, including the drying, decomposition, and reduction of copper-containing sludge. This paper presents an in-depth analysis of the current status of the application of the suspended state technology in the treatment of copper-containing sludge. Based on this analysis, a device for the treatment of copper-containing sludge in the suspended state was designed, through which the characteristics of copper-containing sludge in the oxidative decomposition and reduction phases are investigated. The research objects were gas concentration, temperature, contact state, and particle size time. Orthogonal experiments were initially employed to investigate the relationship between the influencing factors and the conversion rate of copper oxides. This was followed by a single-factor influence study, which led to the determination of the optimal process parameters for the decomposition experiments of the Cu-containing sludge in an oxidizing atmosphere. The 100 µm Cu-containing sludge was reacted with 10% O2 gas at a flow rate of 1 m/s for 3 min under the condition of 900 °C. The process parameters were then determined as follows: The research objects were gas concentration, temperature, contact state, and particle size time. Orthogonal experiments were employed to investigate the relationship between the influencing factors and the copper conversion rate. This was followed by a single-factor influence study, which determined the optimal process parameters for the copper-containing sludge reduction experiments. The 200 µm copper-containing sludge was reacted for 5 min at a flow rate of 7% carbon monoxide at a flow rate of 1.5 m/s under the condition of 800 °C.