The Z-Scheme MIL-88B(Fe)/BiOBr Heterojunction Promotes Fe(III)/Fe(II) Cycling and Photocatalytic-Fenton-Like Synergistically Enhances the Degradation of Ciprofloxacin.

The Z-scheme MIL-88B/BiOBr (referred to as MxBy, whereas x and y are the mass of MIL-88B(Fe) and BiOBr) heterojunction photocatalysts are successfully prepared by a facile ball milling method. By adding low concentration H2O2 under visible light irradiation, the Z-scheme heterojunction and photocatalytic-Fenton-like reaction synergistically enhance the degradation and mineralization of ciprofloxacin (CIP). Among them, M50B150 showed efficient photodegradation efficiency and excellent cycling stability, with 94.6% removal of CIP (10 mg L-1) by M50B150 (0.2 g L-1) under 90 min of visible light. In the MxBy heterojunctions, the rapid transfer of photo-generated electrons not only directly decomposed H2O2 to generate ·OH, but also improved the cycle of Fe3+/Fe2+ pairs, which facilitated the reaction with H2O2 to generate ·OH and ·O2 - radicals. In addition, the effects of photocatalyst dosages, pH of CIP solution, and coexisting substances on CIP removal are systematically investigated. It is found that the photocatalytic- Fenton-like reaction can be carried out at a pH close to neutral conditions. Finally, the charge transfer mechanism of the Z-scheme is verified by electron spin resonance (ESR) signals. The ecotoxicity of CIP degradation products is estimated by the T.E.S.T tool, indicating that the constructed photocatalysis-Fenton-like system is a green wastewater treatment technology.

Unraveling the synergism mechanistic insight of O-vacancy and interfacial charge transfer in WO3-x decorated on Ag2CO3/BiOBr for photocatalysis of water pollutants: Based on experimental and density functional theory (DFT) studies.

Photocatalysis has been widely used as one of the most promising approaches to remove various pollutants in liquid or gas phases during the last decade. The main emphasis of the study is on the synergy of vacancy engineering and heterojunction formation, two widely used modifying approaches, to significantly alter photocatalytic performance. The vacancy-induced Ag2CO3/BiOBr/WO3-x heterojunction system has been fabricated using a co-precipitation technique to efficiently abate methylene blue (MB) dye and doxycycline (DC) antibiotic. The as-fabricated Ag2CO3/BiOBr/WO3-x heterojunction system displayed improved optoelectronic characteristic features because of the rational combination of dual charge transferal route and defect modulation. The Ag2CO3/BiOBr/WO3-x system possessed 97% and 74% photodegradation efficacy for MB and DC, respectively, with better charge isolation and migration efficacy. The ternary photocatalyst possessed a multi-fold increase in the reaction rate for both MB and DC, i.e., 0.021 and 0.0078 min-1, respectively, compared to pristine counterparts. Additionally, more insightful deductions about the photodegradation routes were made possible by the structural investigations of MB and DC using density functional theory (DFT) simulations. This study advances the understanding of the mechanisms forming visible light active dual Z-scheme heterojunction for effective environmental remediation.

Z-scheme Fe@Fe2O3/BiOBr heterojunction with efficient carrier separation for enhanced heterogeneous photo-Fenton activity of tetracycline degradation: Fe2+ regeneration, mechanism insight and toxicity evaluation.

The recombination of photogenerated carrier leads to inefficient Fe2+ regeneration, which limits the extensive application of heterogeneous photo-Fenton. Here, a novel Fe@Fe2O3/BiOBr catalyst with Z-scheme heterojunction structure is designed, and the establishment of the Z-scheme heterojunction facilitates the separation and transfer of photogenerated carrier and maintains the superior redox capability of the system. As-prepared Fe@Fe2O3/BiOBr catalyst exhibits outstanding catalytic performance and stability, especially for the optimum composite FFB-3, its degradation efficiency of tetracycline (TC) achieves 98.22% and the mineralization degree reaches 59.48% within 90 min under natural pH. The preeminent catalytic efficiency benefited from the synergistic of heterogeneous photo-Fenton and Z-scheme carriers transfer mechanism, where Fe2+ regeneration was achieved by photogenerated electrons, and increased hydroxyl radicals were produced with the participation of H2O2 in-situ generated. The results of free-radical scavenging experiment and ESR illustrated that •OH, •O2-, 1O2 and h+ were active species participating in TC degradation. Furthermore, the TC degradation paths were proposed according to LC-MS, and the toxicity evaluation result showed that the toxicity of TC solutions was markedly decreased after degradation. This study provides an innovative strategy for heterogeneous photo-Fenton degradation of antibiotic contaminations by constructing Z-scheme heterojunctions.

Ultrasensitive and specific photoelectrochemical sensor for hydrogen peroxide detection based on pillar[5]arene-functionalized Au nanoparticles and MWNTs hybrid BiOBr heterojunction.

A photoelectrochemical sensor for target detection of hydrogen peroxide was designed based on a new heterojunction nanocomposite which was sulfhydryl-borate ester-modified A1/B1-type pillar[5]arene (BP5)-functionalized Au NPs and multi-walled carbon nanotubes hybridized with bismuth bromide oxide (Au@BP5/MWNTs-BiOBr). The specific sensor was based on the direct induction of oxidation by hydrogen peroxide of the borate ester group of pillar[5]arene. Additionally, the local surface plasmon resonance (LSPR) of Au NPs enhanced visible light capture, the host-guest complexation of BP5 with H2O2 enhanced photocurrent response, the layer-by-layer stacked nanoflower structure of BiOBr provided large specific surface area with more active sites, and the conductivity of MWNTs enhanced the charge separation efficiency and significantly improves the stability of PEC. Their synthesis effect significantly increased the photocurrent signal and further enhanced the detection result. Under the optimal conditions, the linear concentration range of H2O2 detected by the Au@BP5/MWNTs-BiOBr sensor was from 1 to 60 pmol/L. The limit of detection (LOD) and the limit of quantification (LOQ) of the method were 0.333 pmol/L and 1 pmol/L, respectively, and the sensitivity was 6.471 pmol/L. Importantly, the PEC sensor has good stability, reproducibility, and interference resistance and can be used for the detection of hydrogen peroxide in real cells.

Hydrophilicity and Pore Structure Enhancement in Polyurethane/Silk Protein-Bismuth Halide Oxide Composite Films for Photocatalytic Degradation of Dye.

Polyurethane/silk protein-bismuth halide oxide composite films were fabricated using a blending-wet phase transformationin situsynthesis method. The crystal structure, micromorphology, and optical properties were conducted using XRD, SEM, and UV-Vis DRS characterize techniques. The results indicated that loaded silk protein enhanced the hydrophilicity and pore structure of the polyurethane composite films. The active species BiOX were observed to grow as nanosheets with high dispersion on the internal skeleton and silk protein surface of the polyurethane-silk protein film. The photocatalytic efficiency of BiOX/PU-SF composite films was assessed through the degradation of Rhodamine B under visible light irradiation. Among the tested films, the BiOBr/PU-SF composite exhibited the highest removal rate of RhB at 98.9%, surpassing the removal rates of 93.7% for the BiOCl/PU-SF composite and 85.6% for the BiOI/PU-SF composite. Furthermore, an active species capture test indicated that superoxide radical (•O2-) and hole (h+) species played a predominant role in the photodegradation process.

Construction of a Wood Nanofiber-Bismuth Halide Photocatalyst and Catalytic Degradation Performance of Tetracycline from Aqueous Solutions.

Nanostructured bismuth oxide bromide (BiOBr) has attracted considerable attention as a visible light catalyst. However, its photocatalytic degradation efficiency is limited by its low specific surface area. In this study, a solvothermal approach was employed to synthesize BiOBr, which was subsequently loaded onto cellulose nanofibers (CNFs) to obtain a bismuth halide composite catalyst. The performance of this catalyst in the removal of refractory organic pollutants such as tetracycline (TC) from solutions under visible light excitation was examined. Our results indicate that BiOBr/CNF effectively removes TC from the solution under light conditions. At a catalyst dosage of 100 mg/L, the removal efficiency for TC (with an initial concentration of 100 mg/L) was 94.2%. This study elucidates the relationship between the microstructure of BiOBr/CNF composite catalysts and their improved photocatalytic activity, offering a new method for effectively removing pollutants from water.

Nanosheet BiOBr Modified Rock Wool Composites for High Efficient Oil/Water Separation and Simultaneous Dye Degradation by Activating Peroxymonosulfate.

The development of superlyophobic materials in liquid systems, enabling synchronous oil/water separation and dye removal from water, is highly desirable. In this study, we employed a novel superwetting array-like BiOBr nanosheets anchored on waste rock wool (RW) fibers through a simple neutralization alcoholysis method. The resulting BiOBr/RW fibers exhibited superoleophilic and superhydrophilic properties in air but demonstrated underwater superoleophobic and underoil superhydrophobic characteristics. Utilizing its dual superlyophobicity, the fiber layer demonstrated high separation efficiencies and flux velocity for oil/water mixtures by prewetting under a gravity-driven mechanism. Additionally, the novel BiOBr/RW fibers also exhibited excellent dual superlyophobicity and effective separation for immiscible oil/oil systems. Furthermore, the BiOBr/RW fibers could serve as a filter to continuously separate oil/water mixtures with high flux velocity and removal rates (>93.9%) for water-soluble dye rhodamine B (RhB) simultaneously by directly activating peroxymonosulfate (PMS) in cyclic experiments. More importantly, the mechanism of simultaneous oil/water separation and RhB degradation was proposed based on the reactive oxygen species (ROS) quenching experiments and electron paramagnetic resonance (EPR) analysis. Considering the simple modified process and the waste RW as raw material, this work may open up innovative, economical, and environmentally friendly avenues for the effective treatment of wastewater contaminated with oil and water-soluble pollutants.

Efficient removal of tetracycline hydrochloride through novel Fe/BiOBr/Bi2WO6 photocatalyst prepared by dual-strategy under visible-light irradiation.

It is important to investigate whether combining two modification strategies has a synergistic effect on the activity of photocatalysts. In this manuscript, Fe-doped BiOBr/Bi2WO6 heterojunctions were synthesized by a one-pot solvothermal method, and excellent photocatalytic performance was obtained for the degradation of tetracycline hydrochloride (TCH) in water without the addition of surfactant. Combining experiments and characterization, the synergistic effect between Fe ion doping and the BiOBr/Bi2WO6 heterojunction was elucidated. The Fe/BiOBr/Bi2WO6 composite photocatalyst had a beneficial void structure, enhanced visible light response, and could inhibit the recombination of photogenerated support well, which improved the photocatalytic activity. The presented experiments demonstrate that Fe/BiOBr/Bi2WO6 removes 97% of TCH from aqueous solution, while pure BiOBr and Bi2WO6 only remove 56% and 65% of TCH, respectively. Finally, the separation and transfer mechanisms of photoexcited carriers were determined in conjunction with the experimental results. This study provides a new direction for the design of efficient photocatalysts through the use of a dual co-modification strategy.

Unique Tubular BiOBr/g-C3 N4 Heterojunction with Efficient Separation of Charge Carriers for Photocatalytic Nitrogen Fixation.

The industrial ammonia synthesis process consumes a lot of energy and causes serious environmental pollution. As a sustainable approach for ammonia synthesis, photocatalytic nitrogen reduction employing water as the reducing agent has a lot of potential. A simple surfactant-assisted solvothermal method is used to synthesize g-C3 N4 nanotubes with flower-like spherical BiOBr grown inside and outside (BiOBr/g-C3 N4 , BC). The hollow tubular structure realizes the full use of visible light by the multi-scattering effect of light. Large surface areas and more active sites for N2 adsorption and activation are present in the distinctive spatially dispersed hierarchical structures. Particularly, the quick separation and transfer of electrons and holes are facilitated by the sandwich tubular heterojunctions and tight contact interface of BiOBr and g-C3 N4 . The maximal NH3 generation rate of the BiOBr/g-C3 N4 composite catalysts can reach 255.04 µmol⋅ g-1 ⋅ h-1 , and it is 13.9 and 5.8 times that of pure BiOBr and g-C3 N4 . This work provides a novel method for designing and constructing unique heterojunctions for efficient photocatalytic nitrogen fixation.

In situfabrication of S-type BiOIxBryheterojunction with metallic Bi for boosting photocatalytic activity for CO2reduction.

Heterojunction construction and morphology control have always been considered effective ways to promote the capability of photocatalysts. In this work, BiOIxBry, S-type heterojunction photocatalysts with metallic Bi nanoparticles, were synthesizedin situusing a solvothermal method, and the influence of reaction temperature (180 °C-220 °C) and dopant doping amount on the catalysts' microscopic morphology, structure, and catalytic properties were researched. Study results revealed the 1:1 BiOIxBrysynthesized at 200 °C exhibited the optimum behavior in CO2reduction. Its catalytic CO2reduction to CH3OH was 932.88µmol gcat-1and C2H5OH was 324.46µmol gcat-1under the analog light source for 8 h, which was approximately 1.92 and 1.49 times higher than that of BiOI-200 °C, respectively. The reinforced catalytic properties are probably attributed to the synergistic effect between metallic Bi nanoparticles and BiOIxBryheterojunction. Thanks to the SPR effect ofin situmetallic Bi, the catalysts' photocarrier separation efficiency is facilitated. Additionally, the heterojunction formation contributes to that trend and more importantly, preserves the charge carriers with strong redox capacity in BiOIxBry, proving product selectivity. We also present a potential electron transfer mechanism involved in the BiOIxBryphotocatalytic CO2reduction based on the characterization analysis and experimental results.

Enhanced generation of oxysulfur radicals by the BiOBr/Montmorillonite activated sulfite system: Performance and mechanism.

The easily synthesized, cost-effective, and stable photocatalysts for sulfite activation are always required for the enhancement of organic contaminants degradation. Herein, the facile coprecipitation synthesis of Bismuth oxybromide (BiOBr)/Montmorillonite (MMT) was reported, which could activate sulfite (SO32-/HSO3-) under sunlight and accelerate the catalytic performance more effectively than pristine BiOBr. After adding sulfite to the photocatalysis system, the photodegradation efficiency of atrazine (ATZ) achieved 73.7% ± 1.5% after 5 min and 94.4% ± 1.6% after 30 min of sunlight irradiation with BiOBr/MMT. The BiOBr/MMT-sulfite system also presented remarkable photocatalytic performance to eliminate various contaminants, including ciprofloxacin, sulfadiazine, tetracycline, and carbamazepine. The various features of the photocatalyst materials were studied, including their surface morphology, structure, optical properties, and composition. The results illustrated that by adding MMT, the bandgap of the pristine BiOBr was reduced and the surface area was increased, which led to an increased ability to adsorb materials. Results of various influence factors showed this enhanced system had satisfactory and stable removal performance of ATZ in the pH range of 3.0-6.5, but HPO42- had a strong negative effect on the system performance. Oxysulfur radicals (SO5·- and SO4·-), h+, and 1O2 were discovered as the prevailing active species in the BiOBr/MMT-sulfite system. The proposed degradation mechanism of this photocatalyst-enhanced system revealed that sulfite adsorption on the surface of the photocatalyst played a vital role during the initial phase, and the degradation pathway of ATZ was discussed. This study provides a new synthesis strategy of a photocatalyst for sulfite activation and expands the potential uses of Bi-based photocatalysts in degrading difficult-to-remove organic pollutants.

Photocatalytic activity of visible-light-driven L-Proline-TiO2/BiOBr nanostructured materials for dyes degradation: The role of generated reactive species.

L-Proline (2%)-TiO2/BiOBr (30%) nanocomposite was synthesized to obtain high photocatalytic performance in the visible light region and infrared radiation(IR) for methylene blue (MB) and congo red (CR) removal from the contaminated wastewater. L-Proline (2%)-TiO2/BiOBr (30%) photocatalyst with strong absorption near IR wavelength and high charge separation ability was fabricated for the first time. X-ray diffraction (XRD), Fourier transform infrared (FTIR), field-emission scanning electron microscope (FESEM)/Energy Dispersive X-ray (EDX), UV-Vis diffuse reflectance spectrum (DRS), photoluminescence (PL) and Brunauer-Emmett-Teller (BET) characterization techniques show that the visible driven nanocomposite was successfully synthesized. According to the UV-DRS analysis, the estimated band gaps for the L-proline (2%)-TiO2 and L-Proline (2%)-TiO2/BiOBr (30%) nanostructures were respectively 2.3 eV and 2.1 eV.The nanoparticles exhibited enhanced photocatalytic activity (93-100%) and high mineralization efficiency (71-89% TOC removal) for both the dyes. The best photocatalytic activity was achieved by adding 2 wt% of L-Proline and 30 wt% of BiOBr into TiO2 sol. Response surface methodology (RSM) was employed to find significant parameters and their optimum values for maximum degradation, which show pH, dye concentration, irradiation time, and catalyst dosage for both the dyes are significant. The best photocatalytic degradation efficiency was achieved at the optimum conditions of pH = 7.7, catalyst dosage = 0.71 g/L, irradiation time = 142 and dye concentration = 11 mg/L for MB. Scavenger study showed that •OH radicals are responsible for the degradation process.

Controlled Synthesis and Visible-Light-Driven Photocatalytic Activity of BiOBr Particles for Ultrafast Degradation of Pollutants.

For the purpose of regulating the visible-light-driven photocatalytic properties of photocatalysts, we selected BiOBr as the research target and various routes were used. Herein, via the use of a hydrothermal method with various solvents, BiOBr particles with controllable morphology and photocatalytic activities are obtained. In particular, through changing the volume ratio of ethylene glycol (EG) to ethanol (EtOH), BiOBr compounds possess microspheres, in which samples synthesized by using EG:EtOH = 1:2 have the highest photocatalytic activity, and can completely decompose RhB under visible light irradiation within 14 min. Furthermore, we also used different volume ratios of EG and H2O reaction solvents to prepare BiOBr particles so as to further improve its pollutant removal ability. When the volume ratio of EG to H2O is 1:1, the synthesized BiOBr particles have the best photocatalytic activity, and RhB can be degraded in only 10 min upon visible light irradiation. Aside from the reaction solvent, the impact of sintering temperature on the photocatalytic properties of BiOBr particles is also explored, where its pollutant removal capacities are restrained due to the reduced specific surface area. Additionally, the visible-light-triggered photocatalytic mechanism of BiOBr particles is determined by h+, ·OH and ·O2- active species.

Light Control-Induced Oxygen Vacancy Generation and In Situ Surface Heterojunction Reconstruction for Boosting CO2 Reduction.

The weak adsorption of CO2 and the fast recombination of photogenerated charges harshly restrain the photocatalytic CO2 reduction efficiency. The simultaneous catalyst design with strong CO2 capture ability and fast charge separation efficiency is challenging. Herein, taking advantage of the metastable characteristic of oxygen vacancy, amorphous defect Bi2O2CO3 (named BOvC) was built on the surface of defect-rich BiOBr (named BOvB) through an in situ surface reconstruction progress, in which the CO32- in solution reacted with the generated Bi(3-x)+ around the oxygen vacancies. The in situ formed BOvC is tightly in contact with the BOvB and can prevent the further destruction of the oxygen vacancy sites essential for CO2 adsorption and visible light utilization. Additionally, the superficial BOvC associated with the internal BOvB forms a typical heterojunction promoting the interface carriers' separation. Finally, the in situ formation of BOvC boosted the BOvB and showed better activity in the photocatalytic reduction of CO2 into CO (three times compared to that of pristine BiOBr). This work provides a comprehensive solution for governing defects chemistry and heterojunction design, as well as gives an in-depth understanding of the function of vacancies in CO2 reduction.

A Bifunctional BiOBr/ZIF-8/ZnO Photocatalyst with Rich Oxygen Vacancy for Enhanced Wastewater Treatment and H2O2 Generation.

Photocatalytic technology is considered an ideal approach for clean energy conversion and environmental pollution applications. In this work, a bifunctional BiOBr/ZIF-8/ZnO photocatalyst was proposed for removing phenols in wastewater and generating hydrogen peroxide. Insights from scanning electron microscopy measurements revealed the well-dispersion of ZIF-8/ZnO was on the BiOBr layer, which could effectively prevent agglomeration of ZIF-8 and facilitate the separation of carriers. In addition, the optimal H2O2 yield of the BiOBr/ZIF-8/ZnO sample could reach 116 mmol·L-1·g-1 within 2 h, much higher than that of pure BiOBr (with the value of 82 mmol·L-1·g-1). The optimal BiOBr/ZIF-8/ZnO sample could also remove 90% of the phenol or bisphenol A in 2 h, and its kinetic constants were 3.8 times and 2.3 times that of pure BiOBr, respectively. Based on the analysis of the various experimental characterizations, the photocatalytic mechanism of the S-scheme BiOBr/ZIF-8/ZnO composite for the degradation of phenolic pollutants and generation of H2O2 was proposed. The formation of the heterojunction and the oxygen vacancy work together to significantly improve its photocatalytic efficiency. In addition, the BiOBr/ZIF-8/ZnO catalyst has a certain impact on the degradation of phenol in actual wastewater, providing a way to effectively remove refractory pollutants and generate H2O2 in actual water.

A New Strategy of Chemical Photo Grafting Metal Organic Framework to Construct NH2-UiO-66/BiOBr/PVDF Photocatalytic Membrane for Synergistic Separation and Self-Cleaning Dyes.

Photocatalytic membranes are typical multifunctional membranes that have emerged in recent years. The lack of active functional groups on the surface of membranes made of inert materials such as polyvinylidene fluoride(PVDF) makes it difficult to have a stable binding interaction with photocatalysts directly. Therefore, in this study, we developed a simple method to prepare NH2-UiO-66/BiOBr/PVDF(MUB) membranes for efficient dye treatment by grafting benzophenolic acid-functionalized NH2-UiO-66 onto the surface of membranes with photocatalytic properties under visible light irradiation using benzophenolic acid with photoinitiating ability as an anchor. The structural characteristics, photocatalytic properties, antifouling properties, and reusability of the composite membranes were investigated in subsequent experiments using a series of experiments and characterizations. The results showed that the benzophenone acid grafting method was stable and the nanoparticles were not easily dislodged. The MUB composite membrane achieved a higher dye degradation efficiency (99.2%) than the pristine PVDF membrane at 62.9% within a reaction time of 180 min. In addition, the composite membranes exhibited higher permeate fluxes for both pure and mixed dyes and also demonstrated outstanding water flux recovery (>96%) after the light self-cleaning cycle operation. This combination proved to improve the performance of the membranes instead of reducing them, increasing their durability and reusability, and helping to broaden the application areas of membrane filtration technology.

Construction of Ag2CO3/BiOBr/CdS ternary composite photocatalyst with improved visible-light photocatalytic activity on tetracycline molecule degradation.

Photocatalytic degradation was considered as a best strategy for the removal of antibiotic drug pollutants from wastewater. The photocatalyst of ABC (Ag2CO3/BiOBr/CdS) composite synthesized by hydrothermal and precipitation method. The ABC composite used to investigate the degradation activity of tetracycline (TC) under visible light irradiation. The physicochemical characterization methods (e.g. scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution-transmission electron microscopy (HR-TEM), ultraviolet visible spectroscopy (UV), photoluminescence (PL) and time resolved photoluminescence (TRPL) clearly indicate that the composite has been construct successfully that enhances the widened visible light absorption, induces charge transfer and separation efficiency of electron - hole pairs. The photocatalytic activity of all samples was examined through photodegradation of tetracycline in aqueous medium. The photocatalytic degradation rate of ABC catalyst could eliminate 98.79% of TC in 70 min, which is about 1.5 times that of Ag2CO3, 1.28 times that of BiOBr and 1.1 times that of BC catalyst, respectively. The role of operation parameters like, TC concentration, catalyst dosage and initial pH on TC degradation activity were studied. Quenching experiment was demonstrated that ·OH and O2·- were played a key role during the photocatalysis process that was evidently proved in electron paramagnetic resonance (EPR) experiment. In addition, the catalyst showed good activity perceived in reusability and stability test due to the synergistic effect between its components. The mechanism of degradation of TC in ABC composite was proposed based on the detailed analysis. The current study will give an efficient and recyclable photocatalyst for antibiotic aqueous pollutant removal.

Oxygen Vacancies-Rich Heterojunction of Ti3 C2 /BiOBr for Photo-Excited Antibacterial Textiles.

Pathogenic bacteria that adhere on the surface of textiles, especially healthcare workers' uniforms, have brought severe problems, including nosocomial infection and other infectious diseases. Here, antibacterial textiles are fabricated by in situ growing oxygen vacancies (OVs) BiOBr on the surface of Ti3 C2 nanosheets followed by in situ polymerization of polypyrrole (ppy). The formed Schottky heterojunction containing OVs of Ti3 C2 /BiOBr effectively enhance the transfer and separation of photogenerated carriers, inhibit the recombination, and decrease the band gap by introducing defect level, which significantly improve the photocatalytic activity, leading to higher reactive oxygen species (ROS) under light irradiation. Therefore, the antibacterial efficacy of textiles reaches up to 98.64% against Staphylococcus aureus and 99.89% against Escherichia coli with the assistance of hyperthermia under light irradiation for 15 min. This work provides insights for designing photo-excited antibacterial textiles by interfacial construction based on Schottky junctions and OVs in the incorporated nanomaterials.

Novel highly-active Ag/Bi dual nanoparticles-decorated BiOBr photocatalyst for efficient degradation of ibuprofen.

The surface plasmon resonance (SPR) effect of noble nanometals can be utilized to effectively improve the catalytic performance of semiconductor photocatalysts. In this work, a novel composite photocatalyst of BiOBr microspheres simultaneously decorated by Ag and Bi dual nanoparticles (NPs) has been successfully synthesized by the hydrothermal method plus one-step reduction method. And the morphology, structure, chemical composition and photoelectrical properties of this composite photocatalyst (Ag/Bi-BiOBr) were further characterized. Due to the SPR effect of Ag and Bi dual NPs, Ag/Bi-BiOBr showed the high light absorption with narrow band gap, as well as fast charge separation via metal-semiconductor heterojunction so as to realize an efficient degradation of ibuprofen (IBP) under simulated solar irradiation. Through the further optimization of the loading amounts of Ag and Bi dual NPs, the excellent photocatalytic activity in the Ag/Bi-BiOBr has been achieved that 92.3% of IBP was removed within 60 min, which is among the best results reported so far for IBP degradation via photocatalysis.

Enhanced synchronous photocatalytic 4-chlorophenol degradation and Cr(VI) reduction by novel magnetic separable visible-light-driven Z-scheme CoFe2O4/P-doped BiOBr heterojunction nanocomposites.

The co-existence of organic contaminants and heavy metals including 4-chlorophenol (4-CP) and Cr(VI) in aquatic system have become a challenging task in the wastewater treatment. Herein, the synchronous photocatalytic decomposition of 4-CP and Cr(VI) over new Z-scheme CoFe2O4/P-BiOBr heterojunction nanocomposites were revealed. In this work, the nanocomposites were successfully developed via a surfactant-free hydrothermal method. The heterojunction interface was created by decorating magnetic CoFe2O4 nanoparticles onto P-BiOBr nanosheets. The as-fabricated CoFe2O4/P-BiOBr nanocomposites substantially improved the synchronous decomposition of 4-CP and Cr(VI) compared to the single-phase component samples under visible light irradiation. Particularly, the 30-CoFe2O4/P-BiOBr nanocomposite displayed the best photocatalytic performance, which decomposed 95.6% 4-CP and 100% Cr(VI) within 75 min. The photocatalytic improvement was assigned to the Z-scheme heterojunction assisted charge migration between CoFe2O4 and P-BiOBr, and the acceleration of charge carrier separation was validated by the findings of charge dynamics measurements. The harmful 4-CP was photodegraded into smaller organics whereas the Cr(VI) was photoreduced into Cr(III) after 30-CoFe2O4/P-BiOBr photocatalysis, and the good recyclability of fabricated nanocomposite in photocatalytic reaction also showed promising potential for practical applications in environmental remediation. Finally, the radical quenching tests confirmed that there existed the Z-scheme path of charge migration in CoFe2O4/P-BiOBr nanocomposite, which was the mechanism responsible for its high photoactivity.