Catalytic Ozonation of Reactive Black 5 in Aqueous Solution Using Iron-Loaded Dead Leaf Ash for Wastewater Remediation.

In the current study, iron-loaded dead leaf ash (Fe-DLA) was used as a novel catalyst in the heterogeneous catalytic ozonation process (HCOP) for textile wastewater containing Reactive Black 5 (RB-5). The research demonstrates a significant boost in removal efficiency, reaching 98.76% with 1.0 g/min O3 and 0.5 g/L catalyst dose, by investigating key variables such as pH, ozone and catalyst doses, initial concentration, and the presence of scavengers in 1 L wastewater. The addition of tert-butyl alcohol (TBA) reduced RB-5 elimination, indicating the involvement of OH radicals. Catalyst reusability decreased slightly (2.05% in the second run; 4.35% in the third), which was attributed to iron leaching. A comparison of single ozonation (Fe-DLA) adsorption and catalytic ozonation processes (Fe-DLA/O3) revealed that the combined process improved dye degradation by 25%, with removal rates ranking as Fe-DLA adsorption O3 Fe-DLA/O3, with an impressive 76.44% COD removal. These results strongly support RB-5 removal using Fe-DLA and HCOP at a basic pH, highlighting the catalyst's utility in practical wastewater treatment.

Accessible Eco-Friendly Method for Wastewater Removal of the Azo Dye Reactive Black 5 by Reusable Protonated Chitosan-Deep Eutectic Solvent Beads.

A novel approach to enhance the utilization of low-cost and sustainable chitosan for wastewater remediation is presented in this investigation. The study centers around the modification of chitosan beads using a deep eutectic solvent composed of choline chloride and urea at a molar ratio of 1:2, followed by treatment with sulfuric acid using an impregnation accessible methodology. The effectiveness of the modified chitosan beads as an adsorbent was evaluated by studying the removal of the azo dye Reactive Black 5 (RB5) from aqueous solutions. Remarkably, the modified chitosan beads demonstrated a substantial increase in adsorption efficiency, achieving excellent removal of RB5 within the concentration range of 25-250 mg/L, ultimately leading to complete elimination. Several key parameters influencing the adsorption process were investigated, including initial RB5 concentration, adsorbent dosage, contact time, temperature, and pH. Quantitative analysis revealed that the pseudo-second-order kinetic model provided the best fit for the experimental data at lower dye concentrations, while the intraparticle diffusion model showed superior performance at higher RB5 concentration ranges (150-250 mg/L). The experimental data were successfully explained by the Langmuir isotherm model, and the maximum adsorption capacities were found to be 116.78 mg/g at 298 K and 379.90 mg/g at 318 K. Desorption studies demonstrated that approximately 41.7% of the dye could be successfully desorbed in a single cycle. Moreover, the regenerated adsorbent exhibited highly efficient RB5 removal (80.0-87.6%) for at least five consecutive uses. The outstanding adsorption properties of the modified chitosan beads can be attributed to the increased porosity, surface area, and swelling behavior resulting from the acidic treatment in combination with the DES modification. These findings establish the modified chitosan beads as a stable, versatile, and reusable eco-friendly adsorbent with high potential for industrial implementation.

Aminated Rapeseed Husks (Brassica napus) as an Effective Sorbent for Removing Anionic Dyes from Aqueous Solutions.

The study investigated the effect of modifying rapeseed husks with ammonia and epichlorohydrin on their sorption capacity against anionic reactive dyes: Reactive Black 5 (RB5) and Reactive Yellow 84 (RY84). Its scope included sorbents characterization (FTIR, pHPZC), determination of pH influence on the sorption effectiveness of dyes, the adsorption kinetics of dyes, as well as the maximum sorption capacity. The study proved that the reaction of rapeseed husk biomass with ammonia can lead to its amination, namely to the introduction of amine functional groups into the material's structure. The sorption effectiveness of RB5 and RY84 on the tested sorbents was the highest in the pH range of 2-3. The dye sorption kinetics was well described by the pseudo-second-order model. The sorption equilibrium time ranged from 90 to 180 min, and depended on the initial concentration of dyes and the number of amino groups on the sorbent's surface. The most efficient of the sorbents tested were rapeseed husks pre-activated with epichlorohydrin and then aminated with ammonia. Their sorption capacity determined for RB5 and RY84 was 135.83 mg/g and 114.23 mg/g, respectively, which was 794% and 737% higher than that of the non-modified husks.

Decolorization of reactive azo dye using novel halotolerant yeast consortium HYC and proposed degradation pathway.

The presence of high salinity levels in textile wastewater poses a significant obstacle to the process of decolorizing azo dyes. The present study involved the construction of a yeast consortium HYC, which is halotolerant and was recently isolated from wood-feeding termites. The consortium HYC was mainly comprised of Sterigmatomyces halophilus SSA-1575 and Meyerozyma guilliermondii SSA-1547. The developed consortium demonstrated a decolourization efficiency of 96.1% when exposed to a concentration of 50 mg/l of Reactive Black 5 (RB5). The HYC consortium significantly decolorized RB5 up to concentrations of 400 mg/l and in the presence of NaCl up to 50 g/l. The effects of physicochemical factors and the degradation pathway were systematically investigated. The optimal pH, salinity, temperature, and initial dye concentration were 7.0, 3%, 35 °C and 50 mg/l, respectively. The co-carbon source was found to be essential, and the addition of glucose resulted in a 93% decolorization of 50 mg/l RB5. The enzymatic activity of various oxido-reductases was assessed, revealing that NADH-DCIP reductase and azo reductase exhibited greater activity in comparison to other enzymes. UV-Visible (UV-vis) spectrophotometry, Fourier-transform infrared spectroscopy (FTIR), high-performance liquid chromatography (HPLC), and gas chromatography-mass spectrometry (GC-MS) were utilized to identify the metabolites generated during the degradation of RB5. Subsequently, a metabolic pathway was proposed. The confirmation of degradation was established through alterations in the functional groups and modifications in molecular weight. The findings indicate that this halotolerant yeast consortium exhibits promising potential of degrading dye compounds. The results of this study offer significant theoretical basis and crucial perspectives for the implementation of halotolerant yeast consortia in the bioremediation of textile and hypersaline wastewater. This approach is particularly noteworthy as it does not produce aromatic amines.

Anaerobic biodegradation of azo dye reactive black 5 by a novel strain Shewanella sp. SR1: Pathway and mechanisms.

The efficiency of microbial populations in degrading refractory pollutants and the impact of adverse environmental factors often presents challenges for the biological treatment of azo dyes. In this study, the genome analysis and azo dye Reactive Black 5 (RB5) degrading capability of a newly isolated strain, Shewanella sp. SR1, were investigated. By analyzing the genome, functional genes involved in dye degradation and mechanisms for adaptation to low-temperature and high-salinity conditions were identified in SR1. The addition of co-substrates, such as glucose and yeast extract, significantly enhanced RB5 decolorization efficiency, reaching up to 87.6%. Notably, SR1 demonstrated remarkable robustness towards a wide range of NaCl concentrations (1-30 g/L) and temperatures (10-30 °C), maintaining efficient decolorization and high biomass concentration. The metabolic pathways of RB5 degradation were deduced based on the metabolites and genes detected in the genome, in which the azo bond was first cleaved by FMN-dependent NADH-azoreductase and NAD(P)H-flavin reductase, followed by deamination, desulfonation, and hydroxylation mediated by various oxidoreductases. Importantly, the degradation metabolites exhibited reduced toxicity, as revealed by toxicity analysis. These findings highlighted the great potential of Shewanella sp. SR1 for bioremediation of wastewaters contaminated with azo dyes.

Synthetic azo dye bio-decolorization by Priestia sp. RA1: process optimization and phytotoxicity assessment.

Azo compounds represent the most diverse group of colorants widely employed in industrial sectors. Being highly toxic and recalcitrant compound, azo dyes pose a threat to plants, animals, and humans. In the present report, bio-decolorization of azo dye, reactive black 5, was evaluated by newly isolated Priestia sp. RA1. Strain RA1 was able to decolorize 97% of 100 ppm reactive black 5 in 60 h. Specific activity of dye decolorization was found to be 0.233 µmol min-1 g-1 dry cells. Successful decolorization over a broad range of pH, salinity, temperature, and initial dye concentration was observed. Phytotoxicity assay on agriculturally important crops showed considerable difference in percentage seed germination and growth when treated with original and bio-decolorized dye samples. Bio-decolorization at high dye concentrations, promising decolorization rate, and non-toxic nature of treated products suggest the potential of strain RA1 for bioremediation of dye-contaminated water and its re-use in the industries.

Sodium hydroxide pre-treated Aspergillus flavus biomass for the removal of reactive black 5 and its toxicity evaluation.

The present study was focused on the removal of Reactive Black 5 (RB5) from aqueous solution using pre treated Aspergillus flavus as a biosorbent. Pre-treatment of fungal biomass with 0.1 M sodium hydroxide facilitated the removal of dye effectively when compared to untreated fungal biomass. Optimum biosorption conditions for RB5 removal was determined as a function of dye concentration (50-400 mg/L), biosorbent concentration (100-500 mg/L), incubation time (1-7hrs), pH (3-8) and temperature (20-50 °C). At the optimum conditions, the maximum removal efficiency of RB5 achieved by NaOH pretreated A. flavus was 91%. The dye removal was studied kinetically and it obeys the pseudo-second order model and the experimental equilibrium data well fitted the Langmuir isotherm indicating monolayer adsorption of dye molecules on the biosorbent. The thermodynamic parameters such as a change in free energy (ΔG), enthalpy (ΔH) and entropy (ΔS) were calculated and negative values of ΔG suggested that the dye removal process was spontaneous at all temperatures. Furthermore, the values of ΔH revealed that the adsorption process was endothermic. Recovery of RB5 from the fungal biomass was effective using 0.1 M Na2CO3 as an eluent. The interaction of adsorbate with biosorbent was analyzed using UV-Vis and FT-IR spectroscopy, SEM and XRD analyses. Phytotoxicity and microbial toxicity studies revealed the non-toxic nature of the treated dye solution. Hence, the fungal biomass pretreated with NaOH was efficient in decolorizing RB5 as well as composite raw industrial effluent generated from dyeing industries.

Influence of Initial pH Value on the Adsorption of Reactive Black 5 Dye on Powdered Activated Carbon: Kinetics, Mechanisms, and Thermodynamics.

The aim of this work was to investigate the influence of initial pH value (pH0) on the isothermal adsorption of Reactive Black 5 (RB5) dye on commercial powdered activated carbon. Four initial pH values were chosen for this experiment: pH0 = 2.00, 4.00, 8.00, and 10.00. In order to investigate the mechanism of adsorption kinetic, studies have been performed using pseudo-first-order and pseudo-second-order kinetic models as well as an intraparticle diffusion model. In addition, thermodynamic parameters of adsorption were determined for pH0 = 4.00. Results of this research showed that the initial pH value significantly influences the adsorption of RB5 dye onto activated carbon. The highest adsorption capacities (qe) and efficiencies of decolouration were observed for initial pH values of pH0 = 2.00 (qe = 246.0 mg g-1) and 10.00 (qe = 239.1 mg g-1) due to strong electrostatic interactions and attractive π···π interactions, respectively. It was also shown that the adsorption of RB5 dye on activated carbon at all initial pH values is kinetically controlled, assuming a pseudo-second-order model, and that intraparticle diffusion is not the only process that influences on the adsorption rate.

Photocatalytic Degradation of Dyes Using Titania Nanoparticles Supported in Metal-Organic Materials Based on Iron.

Composite materials based on titania nanoparticles (TiO2 NPs) and three metal-organic frameworks (MOFs) called MIL-53 (Fe) ((Fe (III) (OH) (1,4-BDC)), MILs (Materials Institute Lavoisier)), MIL-100 (Fe) (Fe3O(H2O)2OH(BTC)2), and Fe-BTC (iron-benzenetricarboxylate) with different percentages of TiO2 NPs (0.5, 1, and 2.5% wt.) were synthesized using the solvothermal method and used as photocatalytic materials in the degradation of two dyes (Orange II and Reactive Black 5 (RB5)). The pristine and composite materials were characterized with X-ray diffraction, Raman, UV-Vis and Fourier transform infrared spectroscopy and scanning electron microscopy techniques. The 2.5TiO2/MIL-100 composite material showed the best results for the degradation of both dyes (Reactive Black 5 and Orange II dye, 99% and 99.5% degradation in 105 and 150 min, respectively). The incorporation of TiO2 NPs into MOFs can decrease the recombination of the change carrier in the MOF, increasing the photocatalytic activity of a pristine MOF. Results therefore indicated that the synthesized MOF nanocomposites have good potential for wastewater treatment.

Enhancing the decolorization activity of Bacillus pumilus W3 CotA-laccase to Reactive Black 5 by site-saturation mutagenesis.

Reactive Black 5 (RB5) is a typical refractory azo dye. Widespread utilization of RB5 has caused a variety of environmental and health problems. The enzymatic degradation of RB5 can be a promising solution due to its superiority as an eco-friendly and cost-competitive process. Bacterial CotA-laccase shows great application prospect to eliminate hazardous dyes from wastewater. However, efficient decolorization of RB5 CotA-laccase generally requires the participation of costly, toxic mediators. In the present study, we modified the amino acids Thr415 and Thr418 near the type 1 copper site and the amino acid Gln442 at the entrance of the substrate-binding pocket of Bacillus pumilus W3 CotA-laccase to boost its RB5 decolorization activity based on molecular docking analysis and site-saturation mutagenesis. Through the strategies, two double site mutants T415D/Q442A and T418K/Q442A obtained demonstrated 43.94 and 52.64% RB5 decolorization rates in the absence of a mediator at pH 10.0, respectively, which were about 3.70- and 4.43-fold higher compared with the wild-type CotA-laccase. Unexpectedly, the catalytic efficiency of the T418K/Q442A to ABTS was enhanced by 5.33-fold compared with the wild-type CotA-laccase. The mechanisms of conferring enhanced activity to the mutants were proposed by structural analysis. In summary, the mutants T415D/Q442A and T418K/Q442A have good application potentials for the biodegradation of RB5. KEY POINTS: • Three amino acids of CotA-laccase were manipulated by site-saturation mutagenesis. • Decolorization rate of two mutants to RB5 was enhanced 3.70- and 4.43-fold, respectively. • The mechanisms of awarding enhanced activity to the mutants were supposed.

Response of Trametes hirsuta to hexavalent chromium promotes laccase-mediated decolorization of reactive black 5.

The recalcitrant azo dyes combined with heavy metals constitute a major challenge for the bioremediation of industrial effluents. This study aimed to investigate the effect and mechanism of action of a white-rot fungus Trametes hirsuta TH315 on the simultaneous removal of hexavalent chromium [Cr(VI)] and azo dye (Reactive Black 5, RB5). Here, this study discovered that toxic Cr(VI) (1 mM) greatly promoted RB5 decolorization (from 57.15% to 83.65%) by white-rot fungus Trametes hirsuta with high Cr(VI)-reducing ability (>96%), resulting in the simultaneous removal of co-contaminants. On the basis of transcriptomic and biochemical analysis, our study revealed that the oxidative stress in co-contaminants mainly caused by Cr(VI), and a number of dehydrogenases and oxidases showed up-regulation in response to Cr(VI) stress. It was noteworthy that the oxidative stress caused by Cr(VI) in co-contaminants can both significantly induce glutathione S-transferase and laccase expression. Glutathione S-transferase potentially involved in antioxidation against Cr(VI) stress. Laccase was found to play a key role in RB5 decolorization by T. hirsuta. These results suggested that the simultaneous removal of co-contaminants by T. hirsuta could be achieved with Cr(VI) exposure. Overall, the elucidation of the molecular basis in details will help to advance the general knowledge about the fungus by facing harsh environments, and put forward a further possible application of fungi on environmental remediation.

Adsorptive removal of anionic dye (Reactive Black 5) from aqueous solution using chemically modified banana peel powder: kinetic, isotherm, thermodynamic, and reusability studies.

The removal of Reactive Black 5 (RB5) using chemically modified banana peel powder (CMBPP) from aqueous solution was dealt with in the present investigation. Factors affecting the adsorption of RB5 (like pH solution, agitation speed, initial concentration of RB5, contact time and temperature) were investigated. FTIR, SEM-EDX, BET and Elemental analysis characterized the adsorbent material. Adsorption kinetic results evaluated by non-linear pseudo-second-order model was fitted well and showed good correlation with the experimental data than the pseudo-first-order model. The experimental equilibrium data evaluated by non-linear Langmuir, Freundlich, Dubinin-Radushkevich (D-R), and Temkin equations and the experimental data were well described by the Langmuir isotherm model. Langmuir monolayer sorption capacity of RB5 onto CMBPP was observed at pH 3.0 (211.8 mg/g). The values of thermodynamic parameters revealed that the sorption process was feasible, spontaneous, endothermic, and physisorption in nature, i.e. (ΔG° <0, ΔH° > 0, and ΔS° > 0). Desorption studies reveal that the maximum recovery of RB5 when 0.1 M NaOH solution used as a desorbent. The CMBPP also exhibited excellent regeneration efficiency for the five cycles of successive adsorption-desorption. The results exposed that CMBPP could use as a prospective adsorbent material for the removal of RB5 from aqueous media.

Combined strategy for removal of Reactive Black 5 by biomass sorption on Macrocystis pyrifera and zerovalent iron nanoparticles.

Reactive Black 5, RB5, has been used as a model azo dye to evaluate the removal efficiency of sorption on Macrocystis pyrifera biomass (Mpyr) and commercial zerovalent iron nanoparticles (nZVI) in individual and combined treatments. The best conditions for the treatment with the isolated materials were first determined, and then, in series and combined treatments were performed under these conditions, achieving removal efficiencies higher than 80% of the initial dye concentration. Strengths and weaknesses of all removal strategies (individual, in series and combined) are analyzed regarding the application on real effluents. Mpyr efficiently adsorbed RB5, but also increased the total organic content by partial dissolution of components of the algal biomass. Removal experiments with commercial nZVI were also efficient but liberated Fe to the solution, and sulfanilic acid was observed after the treatment as a product of RB5 degradation. In contrast, after the Mpyr treatment, no sulfanilic acid was detected, suggesting that sulfanilic acid is efficiently adsorbed by the biomass. The best condition was the integrated use of Mpyr and nZVI, with a remarkable removal efficiency (69-80%) obtained after only 1 h of treatment. Finally, nZVI were successfully immobilized in Mpyr, and the hybrid material was used to remove RB5 in continuous flow experiments at pH 3, obtaining a removal capacity of 39.9 mg RB5 g-1 after a total processed volume of 630 mL of [RB5]0 = 100 mg L-1.

Toxicological Assessment and UV/TiO2-Based Induced Degradation Profile of Reactive Black 5 Dye.

In this study, the toxicological and degradation profile of Reactive Black 5 (RB5) dye was evaluated using a UV/TiO2-based degradation system. Fourier transform infrared spectroscopy (FT-IR), thin layer chromatography (TLC), high-performance liquid chromatography (HPLC) and ultra-performance liquid chromatography coupled with mass spectrometry (UPLC-MS) techniques were used to evaluate the degradation level of RB5. The UV-Vis spectral analysis revealed the disappearance of peak intensity at 599 nm (λmax). The FT-IR spectrum of UV/TiO2 treated dye sample manifest appearance of new peaks mainly because of the degraded product and/or disappearance of some characteristics peaks which were present in the untreated spectrum. The HPLC profile verified the RB5 degradation subject to the formation of metabolites at different retention times. A stable color removal higher than 96% with COD removal in the range of 74-82.3% was noted at all evaluated dye concentrations. The tentative degradation pathway of RB5 is proposed following a careful analysis of the intermediates identified by UPLC-MS. Toxicity profile of untreated and degraded dye samples was monitored using three types of human cell lines via MTT assay and acute toxicity testing with Artemia salina. In conclusion, the UV/TiO2-based degradation system could be effectively employed for the remediation of textile wastewater comprising a high concentration of reactive dyes.

Photocatalytic properties of hierarchical CuO nanosheets synthesized by a solution phase method.

CuO nanomaterials were synthesized by a simple solution phase method using cetyltrimethylammonium bromide (CTAB) as a surfactant and their photocatalytic property was determined towards the visible-light assisted degradation of Reactive Black-5 dye. A detailed mechanism for the formation of CuO nanostructures has been proposed. The effect of various experimental parameters such as catalyst amount, dye concentration, pH and oxidizing agent on the dye degradation efficiency was studied. About 87% dye was degraded at pH2 in the presence of CuO nanosheets under visible light. The enhanced photocatalytic activity of CuO nanosheets can be ascribed to good crystallinity, grain size, surface morphology and a strong absorption in the visible region. CuO is found to be a promising catalyst for industrial waste water treatment.

The application of iron mesh double layer as anode for the electrochemical treatment of Reactive Black 5 dye.

In this work a novel anode configuration consisting of an iron mesh double layer is proposed for the electrochemical treatment of wastewater. The removal of Reactive Black 5 dye (RB5) from synthetic contaminated water was used as a model system. At a constant anode surface area, identical process operating parameters and batch process mode, the iron mesh double layer electrode showed better performance compared to the conventional single layer iron mesh. The double layer electrode was characterized by RB5 and chemical oxygen demand (COD) removal efficiency of 98.2% and 97.7%, respectively, kinetic rate constant of 0.0385/min, diffusion coefficient of 4.9×10-5cm2/sec and electrical energy consumption of 20.53kWh/kgdye removed. In the continuous flow system, the optimum conditions suggested by Response Surface Methodology (RSM) are: initial solution pH of 6.29, current density of 1.6mA/cm2, electrolyte dose of 0.15g/L and flow rate of 11.47mL/min which resulted in an RB5 removal efficiency of 81.62%.

Degradation of Reactive Black 5 dye by a newly isolated bacterium Pseudomonas entomophila BS1.

The textile and dye industries are considered as one of the major sources of environmental pollution. The present study was conducted to investigate the degradation of the azo dye Reactive Black 5 (RB 5) using a bacterium isolated from soil samples collected around a textile industry. The bacterial strain BS1 capable of degrading RB 5 was isolated and identified as Pseudomonas entomophila on the basis of 16S rDNA sequencing. The effects of different parameters on the degradation of RB 5 were studied to find out the optimal conditions required for maximum degradation, which was 93% after 120 h of incubation. Static conditions with pH in the range of 5-9 and a temperature of 37 °C were found to be optimum for degrading RB 5. Enzyme assays demonstrated that P. entomophila possessed azoreductase, which played an important role in degradation. The enzyme was dependent on flavin mononucleotide and NADH for its activity. Furthermore, a possible degradation pathway of the dye was proposed through gas chromatography - mass spectrometry analysis, which revealed that the metabolic products were naphthalene-1,2-diamine and 4-(methylsulfonyl) aniline. Thus the ability of this indigenous bacterial isolate for simultaneous decolorization and degradation of the azo dye signifies its potential application for treatment of industrial wastewaters containing azo dyes.

Selective adsorption of single and binary dyestuffs by citrus peel: Characterization, and adsorption performance.

The powdered citrus peel, which has been replaced with sodium hydroxide, was used in this study to test how well methylene blue and reactive black 5 dyestuff absorbed one or both. To find out about the texture and surface chemistry of modified citrus peel, Fourier transform infrared spectroscopy and scanning electron microscope analyses were carried out. Fourier transform infrared spectroscopy data revealed the presence of amphoteric radicals on the modified citrus peel surface, indicating the effective adsorption of methylene blue and reactive black 5. Many parameters affecting the batch adsorption process, such as modified citrus peel dose (0.1-0.5 g), pH (2-10), time (20-80 min), stirring speed (60-180 rpm), and temperature (20-45 °C), were studied. It is seen that the physical effect is at the forefront, homogeneous monolayer adsorption occurs, and the process fits the Langmuir and pseudo first order models for dyestuffs. Thermodynamic modeling showed that the adsorption of methylene blue and reactive black 5 was spontaneous and endothermic. At pH 2, an adsorption capacity of 0.67 mg/g and a removal efficiency of 66.86% were achieved for reactive black 5. For methylene blue at pH 6, the adsorption capacity was 4.34 mg/g, and the decolorization rate was 87%. The decreases in the removal rates of dyestuffs in the binary system indicate that they are affected by their simultaneous presence in the solution. The results proved that modified citrus peel can be useful for dyestuff removal in single or binary systems, although the removal capacity of modified citrus peel is highly dependent on methylene blue and reactive black 5.

Effect of nano-TiO2 size and utilization ratio on the performance of photocatalytic concretes; self-cleaning, fresh, and hardened state properties.

In this study, photocatalysis technology was used to reduce water pollution. Decolorization of Reactive Black 5 using nano-TiO2 (NT) as a photocatalyst was investigated by adsorption and degradation experiments. Effects of NT particle size and utilization ratio on the time-dependent flow performance, compressive-flexural strength, and Bohme abrasion resistance of cementitious systems were investigated. In addition to the NT-free control mixture, a total of six photocatalytic self-cleaning mortar mixtures (PSCM) were prepared using NT in two different particle sizes (28 and 38 nm) and three different ratios (0.5%, 1%, and 1.5%). The PSCM sample containing 38 nm NT exhibited superior performance in terms of photocatalytic properties compared to the 28 nm state. It was observed that the flow performance of PSCM mixtures with NT substitution is adversely affected regardless of the NT type. Mixtures containing NT with a lower particle size (28 nm) had higher compressive and flexural strengths.

Accelerated mineralization of textile wastewater under 222 nm irradiation from Kr/Cl2 excilamp: an environmentally friendly and energy efficient approach.

The textile dyeing and manufacturing industry is the major producer of significant amounts of wastewater that contain persistent substances such as azo dyes that require adequate remediation measures. Far ultraviolet at 222 nm light may provide an advantage for contaminants degradation as compared to conventional UV sources (254 nm). In this paper, the degradation of reactive black 5 (RB5) in artificial wastewater has been performed using a 222 nm Kr/Cl2 excimer source under direct photolysis and an advanced oxidation process using TiO2/H2O2. The solution pH, catalyst concentration, 222 nm intensity, initial concentration of dye, and addition of H2O2 influence the degradation rate constant. The molar absorption coefficient, quantum yield of RB5 at 222 nm and the electrical energy per order (EEO) from different treatment methods have been reported. RB5 shows 1.26 times higher molar absorption at 222 nm than at 254 nm. The EEO for excimer-222/H2O2 ( ∼ 13 kWh/m3) is five times lower than that of the excimer-222/TiO2 process, which makes the process energy efficient. The degradation of wastewater has been carried out at three distinct pH values (2, 6, and 10), and the pH level of 10 exhibited the highest degree of degradation. The degradation rate in the alkaline medium is 8.27 and 2.05 times higher than in the acidic or ambient medium. Since textile effluent is highly alkaline, this result is significant, as no neutralization of the wastewater is required, and direct treatment is possible. A possible degradation pathway has been established based on Fourier transform infrared spectroscopy (FTIR) and high resolution mass spectroscopy (HRMS) analysis. The phytotoxicity of the treated wastewater has also been evaluated for its suitability for reuse in agriculture. The study reveals that the excimer-222/H2O2 treated wastewater significantly enhanced the germination percentage of Raphanus sativus seed (97%) compared to dye wastewater-grown seeds (75%). This work offers crucial information for future studies on the direct and indirect photolysis of azo dyes, as well as insight into the process of RB5 degradation under Kr/Cl2 excimer radiation.