Highly Antifreezing Thermogalvanic Hydrogels for Human Heat Harvesting in Ultralow Temperature Environments.

Thermogalvanic hydrogels have been quickly developed and are widely used in thermal energy harvesting. However, the freezing behaviors of thermogalvanic hydrogels at subzero temperatures greatly limit their practical applications. Herein, we design an antifreezing thermogalvanic hydrogel based on [Fe(CN)6]3-/4- ions for thermoelectric power generation in ultralow temperature environments. The antifreezing thermogalvanic hydrogels show excellent flexibility at -80 °C owing to the hydrogen bonding between ethylene glycol and water molecules. Even after 500 cyclic tensile strains, the thermogalvanic hydrogels can still maintain excellent mechanical stability, and the Seebeck coefficient is as high as 1.43 mV/K, corresponding to a large retention rate of ∼95%. Moreover, we demonstrate a wearable thermoelectric shoe based on antifreezing thermogalvanic hydrogels for harvesting human thermal energy in a simulated winter environment of -30 °C, and the electricity can drive a green LED. This work provides important guidance for the design and optimization of antifreezing thermogalvanic hydrogels.

Aqueous Organic Hydrogen Gas Proton Batteries with Ultrahigh-Rate and Ultralow-Temperature Performance.

Aqueous proton batteries (APBs) have emerged as one of the most promising batteries for large-scale energy storage technology. However, they usually show an undesirable electrochemical performance. Herein, we demonstrate a novel aqueous catalytic hydrogen gas powered organic proton (HOP) battery, which is driven by hydrogen evolution/oxidation redox reactions via commercial nanocatalysts on the anode and coordination/decoordination reactions of C═O with H+ on the cathode. The HOP battery shows an excellent rate capacity of 190.1 mAh g-1 at 1 A g-1 and 71.4 mAh g-1 at 100 A g-1. It also delivers a capacity of 96.6 mAh g-1 after 100000 cycles and operates at temperatures down to -70 °C. Moreover, the HOP battery is fabricated in a large-scale pouch cell with an extended capacity, exhibiting its potential for practical energy storage applications. This work provides new insights into the building of sustainable APBs, which will broaden the horizons of high-performance aqueous batteries.

Atomic Level-Macroscopic Structure-Activity of Inhomogeneous Localized Aggregates Enabled Ultra-Low Temperature Hybrid Aqueous Batteries.

The utilization of hybrid aqueous electrolytes has significantly broadened the electrochemical and temperature ranges of aqueous batteries, such as aqueous zinc and lithium-ion batteries, but the design principles for extreme operating conditions remain poorly understood. Here, we systematically unveil the ternary interaction involving salt-water-organic co-solvents and its intricate impacts on both the atomic-level and macroscopic structural features of the hybrid electrolytes. This highlights a distinct category of micelle-like structure electrolytes featuring organic-enriched phases and nanosized aqueous electrolyte aggregates, enabled by appropriate low donor number co-solvents and amphiphilic anions. Remarkably, the electrolyte enables exceptional high solubility, accommodating up to 29.8 m zinc triflate within aqueous micelles. This configuration maintains an intra-micellar salt-in-water setup, allowing for a broad electrochemical window (up to 3.86 V), low viscosity, and state-of-the-art ultralow-temperature zinc ion conductivity (1.58 mS cm-1 at -80 °C). Building upon the unique nature of the inhomogeneous localized aggregates, this micelle-like electrolyte facilitates dendrite-free Zn plating/stripping, even at -80 °C. The assembled Zn||PANI battery showcases an impressive capacity of 71.8 mAh g-1 and an extended lifespan of over 3000 cycles at -80 °C. This study opens up a promising approach in electrolyte design that transcends conventional local atomic solvation structures, broadening the water-in-salt electrolyte concept.

Unlocking Fast Potassium Ion Kinetics: High-Rate and Long-Life Potassium Dual-Ion Battery for Operation at -60 °C.

Energy storage devices operating at low temperatures are plagued by sluggish kinetics, reduced capacity, and notorious dendritic growth. Herein, novel potassium dual-ion batteries (PDIBs) capable of superior performance at -60 °C, and fabricated by combining MXenes and polytriphenylamine (PTPAn) as the anode and cathode, respectively, are presented. Additionally, the reason for the anomalous kinetics of K+ (faster at low temperature than at room temperature) on the Ti3C2 anode is investigated. Theoretical calculations, crossover experiments, and in situ XRD at room and low temperatures revealed that K+ tends to bind with solvent molecules rather than anions at subzero temperatures, which not only inhibits the participation of PF6 - in the formation of the solid electrolyte interphase (SEI), but also guarantees co-intercalation behavior and suppresses undesirable K+ storage. The advantageous properties at low temperatures endow the Ti3C2 anode with fast K+ kinetics to unlock the outstanding performance of PDIB at ultralow temperatures. The PDIBs exhibit superior rate capability and high capacity retention at -40 °C and -60 °C. Impressively, after charging-discharging for 20,000 cycles at -60 °C, the PDIB retained 86.7 % of its initial capacity. This study reveals the influence of temperatures on MXenes and offers a unique design for dual-ion batteries operating at ultralow temperatures.

Spontaneous Proton Chemistry Enables Ultralow-temperature and Long-life Aqueous Copper Metal Batteries.

Aqueous copper metal batteries with acidic electrolytes are regarded as promising candidates for low-temperature energy storage, benefiting from fast kinetics of protons and acid resistance of copper. Here, a Cu(BF4 )2 electrolyte that spontaneously generates protons is developed for ultralow-temperature copper metal batteries. Systematic studies demonstrate that the hydrolysis of BF4 - generates more protons, rendering the Cu(BF4 )2 among the most effective aqueous electrolyte capable of breaking hydrogen bonds in water molecules. This electrolyte endows a polyaniline/Cu battery to deliver a short charging time of 21 s and a charge/discharge capability of up to 10 A g-1 at -30 °C, along with a high discharge specific capacity of 70 mAh g-1 and a supercapacitor-comparable power density of 3000 W kg-1 . Furthermore, it can exhibit a long and stable cycling lifespan over 10 000 cycles at -50 °C and works well at -70 °C. This work provides an opportunity for intrinsically acidic electrolytes.

Supramolecular Adhesives with Extended Tolerance to Extreme Conditions via Water-Modulated Noncovalent Interactions.

Development of supramolecular adhesives with strong tolerance to extreme conditions has emerged as an important research area. In this study, by balancing supramolecular interactions such as hydrogen bonding interactions, electrostatic interactions, π-π stacking interactions, and cation-π interactions, we designed and prepared a series of two-component supramolecular adhesives derived from small organic molecules. Highly efficient interfacial adhesion with maximum adhesion strength of ≈10.0 MPa was realized on various surfaces in air, organic solvents, or liquid nitrogen. Owing to balanced supramolecular interactions, water participation prolonged and increased the tolerance of the adhesives in extreme environments. We demonstrate that the combination of imidazole-based ionic liquids and phenols can be applied for various interfacial adhesions, thereby aiding the development of next-generation adhesives capable of adapting to various extreme conditions in a controlled manner.

New energy sources and technologies for atrial fibrillation catheter ablation.

Ablation has become a cornerstone for the management of symptomatic atrial fibrillation (AF) in patients where anti-arrhythmic drugs fail. Electrical isolation of the pulmonary veins (PVs) is the basic step for every procedure but is still hampered by tools and energy sources that do not lead to durability of isolation. Novel therapies include high power short duration radiofrequency ablation in combination with optimal cooling of the electrode-tissue interface by irrigation or new electrode material to allow for optimal safe energy transfer. Novel tools include competitive balloon catheters using cryoenergy, laser, or radiofrequency current, or linear array ablation with ultralow temperature cryoablation to enhance durability of lesions. A novel energy source is rapidly evolving in the form of pulsed electrical field ablation resulting in irreversible electroporation of cardiac tissue, potentially without collateral side effects. Beyond PV isolation, ablation targets are still under study as standardized addition of lesion lines shows limited benefits. Mapping of the activation pattern during AF to guide patient-specific target ablation has been developing over the last decade, with mixed results by different platforms. The field of ablation for AF is evolving more rapidly than ever which will hopeful result in better long-term outcomes.

Stacking Fault Driven Phase Transformation in CrCoNi Medium Entropy Alloy.

Phase transformation is an effective means to increase the ductility of a material. However, even for a commonly observed face-centered-cubic to hexagonal-close-packed (fcc-to-hcp) phase transformation, the underlying mechanisms are far from being settled. In fact, different transformation pathways have been proposed, especially with regard to nucleation of the hcp phase at the nanoscale. In CrCoNi, a so-called medium-entropy alloy, an fcc-to-hcp phase transformation has long been anticipated. Here, we report an in situ loading study with neutron diffraction, which revealed a bulk fcc-to-hcp phase transformation in CrCoNi at 15 K under tensile loading. By correlating deformation characteristics of the fcc phase with the development of the hcp phase, it is shown that the nucleation of the hcp phase was triggered by intrinsic stacking faults. The confirmation of a bulk phase transformation adds to the myriads of deformation mechanisms available in CrCoNi, which together underpin the unusually large ductility at low temperatures.

Advanced two-stage cascade configurations for energy-efficient -80 °C refrigeration.

In response to the COVID-19 pandemic, some vaccines have been developed requiring ultralow-temperature refrigeration, and the number of these freezers has been increased worldwide. Ultralow-temperature refrigeration operates with a significant temperature lift and, hence, a massive decrease in energy performance. Therefore, cascade cycles based on two vapor compression single-stage cycles are traditionally used for these temperatures. This paper proposes the combination of six different cycles (single-stage with and without internal heat exchanger, vapor injection, liquid injection, and parallel compression with and without economizer) in two-stage cascades to analyze the operational and energy performance in ultralow-temperature freezers. All this leads to 42 different configurations in which the intermediate cascade temperature is optimized to maximize the coefficient of performance. Ultra-low global warming potential natural refrigerants such as R-290 (propane) and R-170 (ethane) for the cascade high- and low-temperature stage have been considered. From the thermodynamic analysis, it can be concluded that liquid and vapor injection cascade configurations are the most energy-efficient. More specifically, those containing a vapor injection in the low-temperature stage (0.89 coefficient of performance, 40 % higher than traditional configurations). Then, using an internal heat exchanger for such low temperatures is unnecessary in terms of energy performance. The optimum intermediate cascade temperature varies significantly among cycles, from -37 °C to 2 °C, substantially impacting energy performance. Parallel compression configuration improves energy performance over single-stage cycles, but not as much as multi-stage (between 20 % and 30 % lower coefficient of performance). For most of low-temperature cycles, the high-temperature stage can be based on a single-stage cycle while keeping the maximum coefficient of performance.

Ultralow temperature cryoablation: Safety and efficacy of preclinical atrial and ventricular lesions.

BACKGROUND: Ultralow temperature cyroablation (ULTC) is designed to create focal, linear, and circumferential lesions. The aim of this study was to assess the safety, efficacy, and durability of atrial and ventricular ULTC lesions in preclinical large animal models. METHODS AND RESULTS: The ULTC system uses nitrogen near its liquid-vapor critical point to cool 11-cm ablation catheters. The catheter can be shaped to specific anatomies using pre-shaped stylets. ULTC was used in 11 swine and four sheep to create atrial (pulmonary vein isolation and linear ablation) and ventricular lesions. Acute and 90-day success were evaluated by intracardiac mapping and histologic examination. Cryoadherence was observed during all ULTC applications, ensuring catheter stability at target locations. Local electrograms were completely eliminated immediately after the first single-shot ULTC application in 49 of 53 (92.5%) atrial and in 31 of 32 (96.9%) ventricular applications. Lesion depth as measured on histology preparations was 1.96 ± 0.8 mm in atrial and 5.61 ± 2.2 mm in ventricular lesions. In all animals, voltage maps and histology demonstrated transmural and durable lesions without gaps, surrounded by intact collagen fibers without injury to surrounding tissues. Transient coronary spasm could be provoked with endocardial ULTC in the left ventricle in close proximity to a coronary artery. CONCLUSIONS: ULTC created effective and efficient atrial and ventricular lesions in vivo without procedural complications in two large animal models. ULTC lesions were transmural, contiguous, and durable over 3 months.

Ultralow temperature cryoablation using near-critical nitrogen for cavotricuspid isthmus-ablation, first-in-human results.

INTRODUCTION: Cryoablation has evolved as a safe alternative to radiofrequency ablation in the treatment of several supraventricular arrhythmias and has potential advantages, yet is limited by the properties of the cryogen used. We investigated a novel ultralow temperature cryoablation (ULTC) system using nitrogen near its liquid-vapor critical point as a freezing source, achieving temperatures as low as -196 degrees Celsius in a long linear catheter with a continuous energy release. Initial safety, procedural and efficacy outcomes of ULTC are described in patients undergoing cavotricuspid isthmus (CTI) ablation. METHODS AND RESULTS: The Cryocure studies (NCT02355106, NCT02839304) are prospective, single-arm, multi-center, first-in-human clinical studies in 17 patients with atrial flutter (AFL) and 13 patients with atrial fibrillation (AF). A total of 30 patients, mean age 65 ± 8 years old and 67% male, were enrolled and underwent ablation of the CTI. Acute success, defined as the confirmation of stable bidirectional conduction block across the CTI, was achieved in all 30 patients. After 12 months of follow-up, 14 out of 17 AFL patients remained free from any AFL. One (3.3%) procedure-related but not device-related serious adverse event was reported, involving transient inferolateral ST-elevation associated with temporary AV conduction block. CONCLUSION: In this first-in-human clinical study the safety and performance results demonstrate the capabilities of ultralow temperature near-critical nitrogen as an effective energy source for CTI ablation. Ongoing, larger, studies should confirm our findings and evaluate the capabilities to create linear and focal transmural lesions in other arrhythmias.

Cryoimmunology: Opportunities and challenges in biomedical science and practice.

Autologous and allogeneic cryoimmunological medicine is a brand new branch of biomedical science and clinical practice that examines the features and formation of the immune response to immunogenic properties of normal and malignant biological structures altered by ultralow temperature, as well as specific changes in the structural and functional characteristics of immune cells and tissues after cryopreservation. Cryogenic protein denaturation phenomenon provides important insights into the mechanisms underlying the damage to cryogenic lesions immediately after freeze-thawing sessions in bioscience and medicine applications. The newly formed cryocoagulated protein components (cryomodified protein components) are crucial in cryoimmunology from the perspective of the formation of immunological substances at ultralow temperatures. Dendritic cells and cryocell detritus (cryocell debris) formed in living biological tissue after exposure to ultralow temperature in vivo may be an indication of one of the essential mechanisms involved in the cryoimmunological response of living structures to the impact of ultralow temperature exposure. Hence, the formation of new autologous and allogeneic cryoinduced immunogenic substances is a novel concept in biomedical research globally. Accordingly, this review focuses on issues concerning the peculiarities of the interaction of the immune system with a dominant malignant neoplasm tissue after exposure to subzero temperatures, considering the original cryogenic technical approaches. We present an overview of the state-of-the-art methods of cryoimmunology, and their major developments, past and present. The need for the delineation of structural and functional characteristics of the biological substrates of the immune system after cryopreservation that can be used in adoptive cell therapy, especially in cancer patients, is emphasized.

Self-Waveguide Single-Benzene Organic Crystal with Ultralow-Temperature Elasticity as a Potential Flexible Material.

With the increasing popularity and burgeoning progress of space technology, the development of ultralow-temperature flexible functional materials is a great challenge. Herein, we report a highly emissive organic crystal combining ultralow-temperature elasticity and self-waveguide properties (when a crystal is excited, it emits light from itself, which travels through the crystal to the other end) based on a simple single-benzene emitter. This crystal displayed excellent elastic bending ability in liquid nitrogen (LN). Preliminary experiments on optical waveguiding in the bent crystal demonstrated that the light generated by the crystal itself could be confined and propagated within the crystal body between 170 and -196 °C. These results not only suggest a guideline for designing functional organic crystals with ultralow-temperature elasticity but also expand the application region of flexible materials to extreme environments, such as space technology.

Ultralow-temperature device dedicated to soft X-ray magnetic circular dichroism experiments.

A new ultralow-temperature setup dedicated to soft X-ray absorption spectroscopy and X-ray magnetic circular dichroism (XMCD) experiments is described. Two experiments, performed on the DEIMOS beamline (SOLEIL synchrotron), demonstrate the outstanding performance of this new platform in terms of the lowest achievable temperature under X-ray irradiation (T = 220 mK), the precision in controlling the temperature during measurements as well as the speed of the cooling-down and warming-up procedures. Moreover, owing to the new design of the setup, the eddy-current power is strongly reduced, allowing fast scanning of the magnetic field in XMCD experiments; these performances lead to a powerful device for X-ray spectroscopies on synchrotron-radiation beamlines facilities.

Ising Superconductivity and Quantum Phase Transition in Macro-Size Monolayer NbSe2.

Two-dimensional (2D) transition metal dichalcogenides (TMDs) have a range of unique physics properties and could be used in the development of electronics, photonics, spintronics, and quantum computing devices. The mechanical exfoliation technique of microsize TMD flakes has attracted particular interest due to its simplicity and cost effectiveness. However, for most applications, large-area and high-quality films are preferred. Furthermore, when the thickness of crystalline films is down to the 2D limit (monolayer), exotic properties can be expected due to the quantum confinement and symmetry breaking. In this paper, we have successfully prepared macro-size atomically flat monolayer NbSe2 films on bilayer graphene terminated surface of 6H-SiC(0001) substrates by a molecular beam epitaxy (MBE) method. The films exhibit an onset superconducting critical transition temperature (Tconset) above 6 K and the zero resistance superconducting critical transition temperature (Tczero) up to 2.40 K. Simultaneously, the transport measurements at high magnetic fields and low temperatures reveal that the parallel characteristic field Bc//(T = 0) is above 5 times of the paramagnetic limiting field, consistent with Zeeman-protected Ising superconductivity mechanism. Besides, by ultralow temperature electrical transport measurements, the monolayer NbSe2 film shows the signature of quantum Griffiths singularity (QGS) when approaching the zero-temperature quantum critical point.

Upconversion Emission and Dual-Mode Sensing Characteristics of NaYF4:Yb3+/Er3+ Microcrystals at High and Ultralow Temperatures.

In this study, we investigate micrometer-sized NaYF4 crystals double-doped with Yb3+/Er3+ lanthanide ions, designed for temperature-sensing applications. In contrast to previous studies, which focused predominantly on the high-temperature regime, our investigation spans a comprehensive range of both high and ultralow temperatures. We explore the relationship between temperature and the upconversion luminescence (UCL) spectra in both frequency and time domains. Our findings highlight the strong dependence of these spectral characteristics of lanthanide-doped NaYF4 crystals on temperature. Furthermore, we introduce a dual-mode luminescence temperature measurement technique, leveraging the upconversion emission intensity ratio for both green and red emissions. This study also examines the correlation between temperature sensing, energy level disparities, and thermal coupling in Er3+ ions across various temperature scales. Our research contributes to advancing the understanding and application of lanthanide-doped materials, setting a foundation for future innovations in temperature sensing across diverse fields.

Multifunctional Anti-Icing Gel Surface with Enhanced Durability.

Materials with low ice adhesion and long-lasting anti-icing properties remain an ongoing challenge in ultralow temperature environments (≤-30 °C). This study presents a gel material consisting of a polymer matrix (copolymer of polyurethane and acrylamide) and an anti-icing agent, ethylene glycol (EG), designed for anti-icing applications at ultralow temperatures. The surface shows a prolonged droplet freezing delay of ca. 322 s at -30 °C and frost resistance properties. It also exhibits an ice adhesion strength of 1.1 kPa at -10 °C and 39.8 kPa at -50 °C, resulting from the interaction between EG and water molecules that hinders the crystallization of ice as well as the significant mismatch between elastic gel and ice. In addition, the gel surface exhibits favorable anti-icing durability, with an ice adhesion strength below 20.0 kPa after 25 icing/deicing cycles and mechanical scratch tests. The gel demonstrates remarkable thermal durability, achieved through the H-bonds between the EG and polymer matrix. The H-bonds further enhance the anti-icing performance, thereby remarkably decreasing EG depletion and improving anti-icing durability. Overall, these properties suggest the potential application of this gel material in harsh environments including polar regions.

Rechargeable Li/Cl2 Battery Down to -80 °C.

Low temperature rechargeable batteries are important to life in cold climates, polar/deep-sea expeditions, and space explorations. Here, this work reports 3.5-4 V rechargeable lithium/chlorine (Li/Cl2 ) batteries operating down to -80 °C, employing Li metal negative electrode, a novel carbon dioxide (CO2 ) activated porous carbon (KJCO2 ) as the positive electrode, and a high ionic conductivity (≈5-20 mS cm-1 from -80 °C to room-temperature) electrolyte comprised of aluminum chloride (AlCl3 ), lithium chloride (LiCl), and lithium bis(fluorosulfonyl)imide (LiFSI) in low-melting-point (-104.5 °C) thionyl chloride (SOCl2 ). Between room-temperature and -80 °C, the Li/Cl2 battery delivers up to ≈29 100-4500 mAh g-1 first discharge capacity (based on carbon mass) and a 1200-5000 mAh g-1 reversible capacity over up to 130 charge-discharge cycles. Mass spectrometry and X-ray photoelectron spectroscopy probe Cl2 trapped in the porous carbon upon LiCl electro-oxidation during charging. At -80 °C, Cl2 /SCl2 /S2 Cl2 generated by electro-oxidation in the charging step are trapped in porous KJCO2 carbon, allowing for reversible reduction to afford a high discharge voltage plateau near ≈4 V with up to ≈1000 mAh g-1 capacity for SCl2 /S2 Cl2 reduction and up to ≈4000 mAh g-1 capacity at ≈3.1 V plateau for Cl2 reduction.

Activating ultralow upconversion nanothermometry in neodymium sublattice for heart tissue imaging rapid-responsive.

The fields of biosensitivity and biological imaging have received a lot of attention from rare earth-doped upconversion nanoparticles (UCNPs). However, owing to the relatively large energy difference of rare earth ions, biological sensitivity based on UCNPs is restricted to detect at low temperature. Here, we design core-shell-shell NaErF4:Yb@Nd2O3@SiO2 UCNPs as a dual-mode bioprobe that produces blue, green, and red multi-color upconversion emissions at extremely low temperatures between 100 K and 280 K. Based on the thermally coupled energy levels (TCELs) of Er3+ (2H11/2 and 4S3/2) and Nd3+ (4F5/2 and 4F3/2) at 100 K, the greatest relative sensitivity (SR) approaches 12.7% K-1. NaErF4:Yb@Nd2O3@SiO2 injection is used to achieve blue upconversion emission imaging of frozen heart tissue, showing that this UCNP can serve as a low-temperature sensitive biological fluorescence.