Torsobarography: Intra-Observer Reliability Study of a Novel Posture Analysis Based on Pressure Distribution.

Postural deformities often manifest themselves in a sagittal imbalance and an asymmetric morphology of the torso. As a novel topographic method, torsobarography assesses the morphology of the back by analysing pressure distribution along the torso in a lying position. At torsobarography's core is a capacitive pressure sensor array. To evaluate its feasibility as a diagnostic tool, the reproducibility of the system and extracted anatomical associated parameters were evaluated on 40 subjects. Landmarks and reference distances were identified within the pressure images. The examined parameters describe the shape of the spine, various structures of the trunk symmetry, such as the scapulae, and the pelvic posture. The results showed that the localisation of the different structures performs with a good (ICC > 0.75) to excellent (ICC > 0.90) reliability. In particular, parameters for approximating the sagittal spine shape were reliably reproduced (ICC > 0.83). Lower reliability was observed for asymmetry parameters, which can be related to the low variability within the subject group. Nonetheless, the reliability levels of selected parameters are comparable to commercial systems. This study demonstrates the substantial potential of torsobarography at its current stage for reliable posture analysis and may pave the way as an early detection system for postural deformities.

A Theoretical Study on Static Gas Pressure Measurement via Circular Non-Touch Mode Capacitive Pressure Sensor.

A circular non-touch mode capacitive pressure sensor can operate in both transverse and normal uniform loading modes, but the elastic behavior of its movable electrode plate is different under the two different loading modes, making its input-output analytical relationships between pressure and capacitance different. This suggests that when such a sensor operates, respectively, in transverse and normal uniform loading modes, the theory of its numerical design and calibration is different, in other words, the theory for the transverse uniform loading mode (available in the literature) cannot be used as the theory for the normal uniform loading mode (not yet available in the literature). In this paper, a circular non-touch mode capacitive pressure sensor operating in normal uniform loading mode is considered. The elastic behavior of the movable electrode plate of the sensor under normal uniform loading is analytically solved with the improved governing equations, and the improved analytical solution obtained can be used to mathematically describe the movable electrode plate with larger elastic deflections, in comparison with the existing two analytical solutions in the literature. This provides a larger technical space for developing the circular non-touch mode capacitive pressure sensors used for measuring the static gas pressure (belonging to normal uniform loading).

Optimizing Capacitive Pressure Sensor Geometry: A Design of Experiments Approach with a Computer-Generated Model.

This study presents a comprehensive investigation into the design and optimization of capacitive pressure sensors (CPSs) for their integration into capacitive touch buttons in electronic applications. Using the Finite Element Method (FEM), various geometries of dielectric layers were meticulously modeled and analyzed for their capacitive and sensitivity parameters. The flexible elastomer polydimethylsiloxane (PDMS) is used as a diaphragm, and polyvinylidene fluoride (PVDF) is a flexible material that acts as a dielectric medium. The Design of Experiment (DoE) techniques, aided by statistical analysis, were employed to identify the optimal geometric shapes of the CPS model. From the prediction using the DoE approach, it is observed that the cylindrical-shaped dielectric medium has better sensitivity. Using this optimal configuration, the CPS was further examined across a range of dielectric layer thicknesses to determine the capacitance, stored electrical energy, displacement, and stress levels at uniform pressures ranging from 0 to 200 kPa. Employing a 0.1 mm dielectric layer thickness yields heightened sensitivity and capacitance values, which is consistent with theoretical efforts. At a pressure of 200 kPa, the sensor achieves a maximum capacitance of 33.3 pF, with a total stored electric energy of 15.9 × 10-12 J and 0.468 pF/Pa of sensitivity for 0.1 dielectric thickness. These findings underscore the efficacy of the proposed CPS model for integration into capacitive touch buttons in electronic devices and e-skin applications, thereby offering promising advancements in sensor technology.

Integrated Wearable System for Monitoring Skeletal Muscle Force of Lower Extremities.

Continuous monitoring of lower extremity muscles is necessary, as the muscles support many human daily activities, such as maintaining balance, standing, walking, running, and jumping. However, conventional electromyography and physiological cross-sectional area methods inherently encounter obstacles when acquiring precise and real-time data pertaining to human bodies, with a notable lack of consideration for user comfort. Benefitting from the fast development of various fabric-based sensors, this paper addresses these current issues by designing an integrated smart compression stocking system, which includes compression garments, fabric-embedded capacitive pressure sensors, an edge control unit, a user mobile application, and cloud backend. The pipeline architecture design and component selection are discussed in detail to illustrate a comprehensive user-centered STIMES design. Twelve healthy young individuals were recruited for clinical experiments to perform maximum voluntary isometric ankle plantarflexion contractions. All data were simultaneously collected through the integrated smart compression stocking system and a muscle force measurement system (Humac NORM, software version HUMAC2015). The obtained correlation coefficients above 0.92 indicated high linear relationships between the muscle torque and the proposed system readout. Two-way ANOVA analysis further stressed that different ankle angles (p = 0.055) had more important effects on the results than different subjects (p = 0.290). Hence, the integrated smart compression stocking system can be used to monitor the muscle force of the lower extremities in isometric mode.

Enhanced capacitive pressure sensing performance by charge generation from filler movement in thin and flexible PVDF-GNP composite films.

This study introduces an approach to overcome the limitations of conventional pressure sensors by developing a thin and lightweight composite film specifically tailored for flexible capacitive pressure sensors, with a particular emphasis on the medium and high pressure range. To accomplish this, we have engineered a composite film by combining polyvinylidene fluoride (PVDF) and graphite nanoplatelets (GNP) derived from expanded graphite (Ex-G). A uniform sized GNPs with an average lateral size of 2.55av and an average thickness of 33.74 av with narrow size distribution was obtained with a gas-induced expansion of expandable graphite (EXP-G) combined with tip sonication in solvent. By this precisely controlled GNP within the composite film, a remarkable improvement in sensor sensitivity has been achieved, surpassing 4.18 MPa-1 within the pressure range of 0.1 to 1.6 MPa. This enhancement can be attributed to the generation of electric charge from the movement of GNP in the polymer matrix. Additionally, stability testing has demonstrated the reliable operation of the composite film over 1000 cycles. Notably, the composite film exhibits exceptional continuous pressure sensing capabilities with a rapid response time of approximately 100 milliseconds. Experimental validation using a 3 × 3 sensor array has confirmed the accurate detection of specific contact points, thus highlighting the potential of the composite film in selective pressure sensing. These findings signify an advancement in the field of flexible capacitive pressure sensors that offer enhanced sensitivity, consistent operation, rapid response time, and the unique ability to selectively sense pressure.

The Fabrication and Evaluation of a Capacitive Pressure Sensor Using Ru-Based Thin Film Metallic Glass with Structural Relaxation by Heat Treatment.

Microelectromechanical systems (MEMS)-based capacitive pressure sensors are conventionally fabricated from diaphragms made of Si, which has a high elastic modulus that limits the control of internal stress and constrains size reduction and low-pressure measurements. Ru-based thin-film metallic glass (TFMG) exhibits a low elastic modulus, and the internal stress can be controlled by heat treatment, so it may be a suitable diaphragm material for facilitating size reduction of the sensor without performance degradation. In this study, a Ru-based TFMG was used to realize a flattened diaphragm, and structural relaxation was achieved through annealing at 310 °C for 1 h in a vacuum. The diaphragm easily deformed, even under low differential pressure, when reduced in size. A diaphragm with a diameter of 1.7 mm was then applied to successfully fabricate a capacitive pressure sensor with a sensor size of 2.4 mm2. The sensor exhibited a linearity of ±3.70% full scale and a sensitivity of 0.09 fF/Pa in the differential pressure range of 0-500 Pa.

A Sensitivity-Optimized Flexible Capacitive Pressure Sensor with Cylindrical Ladder Microstructural Dielectric Layers.

Flexible capacitive pressure sensors have attracted extensive attention due to their dynamic response and good sensing capability for static and small pressures. Using microstructural dielectric layers is an effective method for improving performance. However, the current state of microstructure design is primarily focused on basic shapes and is largely limited by simulation results; there is still a great deal of potential for further innovation and improvement. This paper innovatively proposes to increase the ladder structure based on the basic microstructures, for example, the long micro-ridge ladder, the cuboid ladder, and cylindrical ladder microstructures. By comparing 9 kinds of microstructures including ladder structure through finite element simulation, it is found that the sensor with a cylindrical ladder microstructure dielectric layer has the highest sensitivity. The dielectric layers with various microstructures are obtained by 3D printed molds, and the sensor with cylindrical ladder microstructure dielectric layer has the sensitivity of 0.12 kPa-1, which is about 3.9 times higher than that without microstructure. The flexible pressure sensor developed by us boasts sensitivity-optimized and operational stability, making it an ideal solution for monitoring rainfall frequency in real time.

Dynamic Characterization of a Low-Cost Fully and Continuously 3D Printed Capacitive Pressure-Sensing System for Plantar Pressure Measurements.

In orthopedics, the evaluation of footbed pressure distribution maps is a valuable gait analysis technique that aids physicians in diagnosing musculoskeletal and gait disorders. Recently, the use of pressure-sensing insoles to collect pressure distributions has become more popular due to the passive collection of natural gait data during daily activities and the reduction in physical strain experienced by patients. However, current pressure-sensing insoles face the limitations of low customizability and high cost. Previous works have shown the ability to construct customizable pressure-sensing insoles with capacitive sensors using fused-deposition modeling (FDM) 3D printing. This work explores the feasibility of low-cost fully and continuously 3D printed pressure sensors for pressure-sensing insoles using three sensor designs, which use flexible thermoplastic polyurethane (TPU) as the dielectric layer and either conductive TPU or conductive polylactic acid (PLA) for the conductive plates. The sensors are paired with a commercial capacitance-to-voltage converter board to form the sensing system. Dynamic sensor performance is evaluated via sinusoidal compressive tests at frequencies of 1, 3, 5, and 7 Hz, with pressure levels varying from 14.33 to 23.88, 33.43, 52.54, and 71.65 N/cm2 at each frequency. Five sensors of each type are tested. Results show that all sensors display significant hysteresis and nonlinearity. The PLA-TPU sensor with 10% infill is the best-performing sensor with the highest average sensitivity and lowest average hysteresis and linearity errors. The range of average sensitivities, hysteresis, and linearity errors across the entire span of tested pressures and frequencies for the PLA-TPU sensor with 10% infill is 11.61-20.11·10-4 V/(N/cm2), 11.9-31.8%, and 9.0-22.3%, respectively. The significant hysteresis and linearity error are due to the viscoelastic properties of TPU, and some additional nonlinear effects may be due to buckling of the infill walls of the dielectric.

Customized Textile Capacitive Insole Sensor for Center of Pressure Analysis.

Center of pressure refers to the centroid of the ground reaction force vector detected underneath the walking foot, which is a summary measure representing body segment movements during human locomotion. In this study, we developed a cost-effective, lightweight insole-type textile capacitive sensor (I-TCPs) to analyze plantar pressure (PP) distribution and center of pressure (COP) trajectory. To test the accuracy of I-TCPs, the measured pressure data was compared with that of F-scan. The sensor performance test was divided into a static baseline test and a dynamic gait experiment, both at two different gait speeds self-selected by the subjects. Static gait results showed that I-TCPs were capable of recognizing PP segments at different gait speeds. Dynamic gait results showed an average RMSE of 1.29 ± 0.47 mm in COPx (mediolateral shift) and 12.55 ± 5.08 mm in COPy (anteroposterior shift) at a comfortable gait speed. The COP correlation between I-TCPs and F-scan was 0.54 ± 0.09 in COPx and 0.92 ± 0.04 in COPy in comfortable gait speed conditions, in which COPy values presented a stronger correlation. RMSE and correlation in fast gait speed conditions also showed similar results. The findings of this study can be the basis for future research, including rehabilitation engineering, developing ICT devices, and creating smart wearable sensors to improve quality of life for patients and healthy individuals.

A Further Theoretical Study of Capacitive Pressure Sensors Based on Thin Film Elastic Deflection and Parallel Plate Capacitor: Refined Closed-Form Solution and Numerical Calibration.

The capacitive pressure sensor based on thin film elastic deflection and a parallel plate capacitor uses a non-conductive elastic annular thin film centrally connected to a conductive, rigid, flat, concentric-circular thin plate as a pressure sensing unit. On application of pressure, the non-conductive thin film deflects elastically, which in turn moves the conductive thin plate (as a movable upper electrode plate of the parallel plate capacitor) towards the lower electrode plate, resulting in a change in the capacitance of the capacitor. Therefore, the applied pressure can be determined by measuring the capacitance change, based on the closed-form solution for the elastic behavior of the annular thin film under pressure. Such capacitive pressure sensors are more suitable for large-sized sensors such as those used for building-facade wind pressure measurements, etc. In this paper, a further theoretical study of such capacitive pressure sensors is presented. The newly presented, more refined closed-form solution can greatly reduce the output pressure error under the same input capacitance, in comparison with the previously presented closed-form solution. A numerical example of how to use the resulting closed-form solution to numerically calibrate input-output characteristics is given for the first time. The variation trend of pressure operation ranges and input-output characteristics with important parametric variations, which can be used for guiding the design of such capacitive pressure sensors, is investigated.

A Highly Sensitive and Flexible Capacitive Pressure Sensor Based on Alignment Airgap Dielectric.

Flexible capacitive pressure sensors with a simple structure and low power consumption are attracting attention, owing to their wide range of applications in wearable electronic devices. However, it is difficult to manufacture pressure sensors with high sensitivity, wide detection range, and low detection limits. We developed a highly sensitive and flexible capacitive pressure sensor based on the porous Ecoflex, which has an aligned airgap structure and can be manufactured by simply using a mold and a micro-needle. The existence of precisely aligned airgap structures significantly improved the sensor sensitivity compared to other dielectric structures without airgaps. The proposed capacitive pressure sensor with an alignment airgap structure supports a wide range of working pressures (20-100 kPa), quick response time (≈100 ms), high operational stability, and low-pressure detection limit (20 Pa). Moreover, we also studied the application of pulse wave monitoring in wearable sensors, exhibiting excellent performance in wearable devices that detect pulse waves before and after exercise. The proposed pressure sensor is applicable in electronic skin and wearable medical assistive devices owing to its excellent functional features.

Extending Porous Silicone Capacitive Pressure Sensor Applications into Athletic and Physiological Monitoring.

Porous polymer dielectric materials have been developed to increase the sensitivity of capacitive pressure sensors, so that they might expand capacitive sensor use, and promote the realization of the advantages of this class of sensor in further fields. However, their use has not been demonstrated in physiological monitoring applications such as respiration monitoring and body position detection during sleep; an area in need of unmet medical attention for conditions such as sleep apnea. Here, we develop and characterize a sensor comprised of a poly dimethylsiloxane (PDMS) sponge dielectric layer, and PDMS/carbon black (CB) blend electrode layers, with suitable compliance and sensitivity for integration in mattresses, pillows, and athletic shoe insoles. With relatively high pressure sensitivity (~0.1 kPa-1) and mechanical robustness, this sensor was able to fulfill a wide variety of roles, including athletic monitoring in an impact mechanics scenario, by recording heel pressure during running and walking, and physiological monitoring, by detecting head position and respiration of a subject lying on a pad and pillow. The sensor detected considerably greater relative signal changes than those reported in recent capacitive sensor studies for heel pressure, and for a comparably minimal, resistive sensor during respiration, in line with its enhanced sensitivity.

Carbonized Cotton Fabric-Based Flexible Capacitive Pressure Sensor Using a Porous Dielectric Layer with Tilted Air Gaps.

Flexible and wearable pressure sensors have attracted significant attention owing to their roles in healthcare monitoring and human-machine interfaces. In this study, we introduce a wide-range, highly sensitive, stable, reversible, and biocompatible pressure sensor based on a porous Ecoflex with tilted air-gap-structured and carbonized cotton fabric (CCF) electrodes. The knitted structure of electrodes demonstrated the effectiveness of the proposed sensor in enhancing the pressure-sensing performance in comparison to a woven structure due to the inherent properties of naturally generated space. In addition, the presence of tilted air gaps in the porous elastomer provided high deformability, thereby significantly improving the sensor sensitivity compared to other dielectric structures that have no or vertical air gaps. The combination of knitted CCF electrodes and the porous dielectric with tilted air gaps achieved a sensitivity of 24.5 × 10-3 kPa-1 at 100 kPa, along with a wide detection range (1 MPa). It is also noteworthy that this novel method is low-cost, facile, scalable, and ecofriendly. Finally, the proposed sensor integrated into a smart glove detected human motions of grasping water cups, thus demonstrating its potential applications in wearable electronics.

Highly Sensitive, Breathable, and Flexible Pressure Sensor Based on Electrospun Membrane with Assistance of AgNW/TPU as Composite Dielectric Layer.

Pressure sensors have been widely used in electronic wearable devices and medical devices to detect tiny physical movements and mechanical deformation. However, it remains a challenge to fabricate desirable, comfortable wearing, and highly sensitive as well as fast responsive sensors to capture human body physiological signs. Here, a new capacitive flexible pressure sensor that is likely to solve this problem was constructed using thermoplastic polyurethane elastomer rubber (TPU) electrospinning nanofiber membranes as a stretchable substrate with the incorporation of silver nanowires (AgNWs) to build a composite dielectric layer. In addition, carbon nanotubes (CNTs) were painted on the TPU membranes as flexible electrodes by screen printing to maintain the flexibility and breathability of the sensors. The flexible pressure sensor could detect tiny body signs; fairly small physical presses and mechanical deformation based on the variation in capacitance due to the synergistic effects of microstructure and easily altered composite permittivity of AgNW/TPU composite dielectric layers. The resultant sensors exhibited high sensitivity (7.24 kPa-1 within the range of 9.0 × 10-3 ~ 0.98 kPa), low detection limit (9.24 Pa), and remarkable breathability as well as fast responsiveness (<55 ms). Moreover, both continuously pressing/releasing cycle over 1000 s and bending over 1000 times did not impair the sensitivity, stability, and durability of this flexible pressure sensor. This proposed strategy combining the elastomer nanofiber membrane and AgNW dopant demonstrates a cost-effective and scalable fabrication of capacitive pressure sensors as a promising application in electronic skins and wearable devices.

Evaluation of Pressure Capacitive Sensors for Application in Grasping and Manipulation Analysis.

The analysis of the human grasping and manipulation capabilities is paramount for investigating human sensory-motor control and developing prosthetic and robotic hands resembling the human ones. A viable solution to perform this analysis is to develop instrumented objects measuring the interaction forces with the hand. In this context, the performance of the sensors embedded in the objects is crucial. This paper focuses on the experimental characterization of a class of capacitive pressure sensors suitable for biomechanical analysis. The analysis was performed in three loading conditions (Distributed load, 9 Tips load, and Wave-shaped load, thanks to three different inter-elements) via a traction/compression testing machine. Sensor assessment was also carried out under human- like grasping condition by placing a silicon material with the same properties of prosthetic cosmetic gloves in between the sensor and the inter-element in order to simulate the human skin. Data show that the input-output relationship of the analyzed, sensor is strongly influenced by both the loading condition (i.e., type of inter-element) and the grasping condition (with or without the silicon material). This needs to be taken into account to avoid significant measurement error. To go over this hurdle, the sensors have to be calibrated under each specific condition in order to apply suitable corrections to the sensor output and significantly improve the measurement accuracy.

Highly Sensitive and Flexible Capacitive Pressure Sensors Combined with Porous Structure and Hole Array Using Sacrificial Templates and Laser Ablation.

Flexible, wearable pressure sensors offer numerous benefits, including superior sensing capabilities, a lightweight and compact design, and exceptional conformal properties, making them highly sought after in various applications including medical monitoring, human-computer interactions, and electronic skins. Because of their excellent characteristics, such as simple fabrication, low power consumption, and short response time, capacitive pressure sensors have received widespread attention. As a flexible polymer material, polydimethylsiloxane (PDMS) is widely used in the preparation of dielectric layers for capacitive pressure sensors. The Young's modulus of the flexible polymer can be effectively decreased through the synergistic application of sacrificial template and laser ablation techniques, thereby improving the functionality of capacitive pressure sensors. In this study, a novel sensor was introduced. Its dielectric layer was developed through a series of processes, including the use of a sacrificial template method using NaCl microparticles and subsequent CO2 laser ablation. This porous PDMS dielectric layer, featuring an array of holes, was then sandwiched between two flexible electrodes to create a capacitive pressure sensor. The sensor demonstrates a sensitivity of 0.694 kPa-1 within the pressure range of 0-1 kPa and can effectively detect pressures ranging from 3 Pa to 200 kPa. The sensor demonstrates stability for up to 500 cycles, with a rapid response time of 96 ms and a recovery time of 118 ms, coupled with a low hysteresis of 6.8%. Furthermore, our testing indicates that the sensor possesses limitless potential for use in detecting human physiological activities and delivering signals.

Microstructured Porous Capacitive Bio-pressure Sensor Using Droplet-based Microfluidics.

Background: Devices that mimic the functions of human skin are known as "electronic skin," and they must have characteristics like high sensitivity, a wide dynamic range, high spatial homogeneity, cheap cost, wide area easy processing, and the ability to distinguish between diverse external inputs. Methods: This study introduces a novel approach, termed microfluidic droplet-based emulsion self-assembly (DMESA), for fabricating 3D microstructured elastomer layers using polydimethylsiloxane (PDMS). The method aims to produce accurate capacitive pressure sensors suitable for electronic skin (e-skin) applications. The DMESA method facilitates the creation of uniform-sized spherical micropores dispersed across a significant area without requiring a template, ensuring excellent spatial homogeneity. Results: Micropore size adjustment, ranging from 100 to 600 µm, allows for customization of pressure sensor sensitivity. The active layer of the capacitive pressure sensor is formed by the three-dimensional elastomer itself. Experimental results demonstrate the outstanding performance of the DMESA approach. It offers simplicity in processing, the ability to adjust performance parameters, excellent spatial homogeneity, and the capability to differentiate varied inputs. Capacitive pressure sensors fabricated using this method exhibit high sensitivity and dynamic amplitude, making them promising candidates for various e-skin applications. Conclusion: The DMESA method presents a highly promising solution for fabricating 3D microstructured elastomer layers for capacitive pressure sensors in e-skin technology. Its simplicity, performance adjustability, spatial homogeneity, and sensitivity to different inputs make it suitable for a wide range of electronic skin applications.

Capacitive pressure sensors based on microstructured polymer-derived SiCN ceramics for high-temperature applications.

Traditional silicon-based pressure sensors cannot meet demand of pressure information acquisition in high-temperature extreme environments due to their low sensitivity, limited detection temperature and complex processing. Herein, a capacitive pressure sensor is fabricated using polymer-derived SiCN ceramics with convex microstructures via a sample replication strategy. Its performance is measured at different pressures (0-800 kPa) from room temperature to 500 °C. The results show that the SiCN ceramic capacitive pressure sensor exhibits low hysteresis, good non-linearity of 0.26 %, outstanding repeatability and high sensitivity of 0.197 pF/MPa under room temperature. When the test temperature reaches 500 °C, the performance of the prepared capacitive pressure sensor has no degradation, keeping competent sensitivity of 0.214 pF/MPa and nonlinear error of 0.24 %. Therefore, benefitting from the preeminent high-temperature properties, e.g., excellent oxidation/corrosion resistance and thermal stability, SiCN ceramics capacitive pressure sensors have great potential in the application of high-temperature and harsh environments.

Deep-learning enabled smart insole system aiming for multifunctional foot-healthcare applications.

Real-time foot pressure monitoring using wearable smart systems, with comprehensive foot health monitoring and analysis, can enhance quality of life and prevent foot-related diseases. However, traditional smart insole solutions that rely on basic data analysis methods of manual feature extraction are limited to real-time plantar pressure mapping and gait analysis, failing to meet the diverse needs of users for comprehensive foot healthcare. To address this, we propose a deep learning-enabled smart insole system comprising a plantar pressure sensing insole, portable circuit board, deep learning and data analysis blocks, and software interface. The capacitive sensing insole can map both static and dynamic plantar pressure with a wide range over 500 kPa and excellent sensitivity. Statistical tools are used to analyze long-term foot pressure usage data, providing indicators for early prevention of foot diseases and key data labels for deep learning algorithms to uncover insights into the relationship between plantar pressure patterns and foot issues. Additionally, a segmentation method assisted deep learning model is implemented for exercise-fatigue recognition as a proof of concept, achieving a high classification accuracy of 95%. The system also demonstrates various foot healthcare applications, including daily activity statistics, exercise injury avoidance, and diabetic foot ulcer prevention.

Highly Sensitive Flexible Capacitive Pressure Sensor Based on a Multicross-Linked Dual-Network Ionic Hydrogel for Blood Pressure Monitoring Applications.

Flexible capacitive pressure sensors based on ionic hydrogels (IHs) have garnered significant attention in the field of wearable technology. However, the vulnerability of traditional single-network hydrogels to mechanical damage and the complexity associated with preparing double-network hydrogels present challenges in developing a highly sensitive, easily prepared, and durable IH-based flexible capacitive pressure sensor. This study introduces a novel multicross-linked dual-network IH achieved through the physical and chemical cross-linking of polymers polyvinyl alcohol (PVA) and chitosan (CS), ionic solution H3PO4, and cross-linking agent gum arabic. Flexible capacitive pressure sensors, characterized by high sensitivity and a broad pressure range, are fabricated by employing mesh as templates to design cut-corner cube microstructures with high uniformity and controllability on the IHs. The sensor exhibits high sensitivity across a wide pressure range (0-290 kPa) and with excellent features such as high resolution (∼1.3 Pa), fast response-recovery time (∼11 ms), and repeatable compression stability at 25 kPa (>2000 cycles). The IHs as a dielectric layer demonstrate long-term water retention properties, enabling exposure to air for up to 100 days. Additionally, the developed sensor shows the ability to accurately measure the pulse wave within the small pressure range. By combining the pulse wave acquired by the sensor with a trained neural network model, we achieve successful blood pressure (BP) prediction, meeting the standards set by the Association for the Advancement of Medical Instrumentation and the British Hypertension Society. Ultimately, the sensor proposed in this study holds promising prospects for broad applications in high-precision wearable medical electronic devices.