Industrial Waste Derived Separators for Zn-Ion Batteries Achieve Homogeneous Zn(002) Deposition Through Low Chemical Affinity Effects.

Designing a cost-effective and multifunctional separator that ensures dendrite-free and stable Zn metal anode remains a significant challenge. Herein, a multifunctional cellulose-based separator is presented consisting of industrial waste-fly ash particles and cellulose nanofiber using a facile solution-coating method. The resulting fly ash-cellulose (FACNF) separators enable a high ion conductivity (5.76 mS cm-1) and low desolvation energy barrier of hydrated Zn2+. These features facilitate fast ion transfer kinetics and inhibit water-induced side reactions. Furthermore, experimental results and theoretical simulations confirm that the presence of fly ash particles in FACNF separators effectively accommodate the preferential deposition of Zn(002) planes, due to the weak chemical affinity between Zn(002) plane and fly ash, to mitigate dendrite formation and growth. Consequently, the utilization of FACNF separators causes an impressive cycling performance in both Zn||Zn symmetric cells (1600 h at 2 mA cm-2/1 mAh cm-2) and Zn||(NH4)2V10O25 (NVO) full cells (4000 cycles with the capacity retention of 92.1% at 5 A g-1). Furthermore, the assembled pouch cells can steadily support digital thermometer over two months without generating gas and volume expansion. This work provides new insights for achieving crystallographic uniformity in Zn anodes and realizing cost-effective and long-lasting aqueous zinc-ion batteries (AZIBs).

The dam that fly ash built.

When the first concrete was poured in 1949 for the Hungry Horse Dam (Montana, USA), pozzolan cements had already been used in several major North American dams, including Grand Coulee on the Columbia River (diatomaceous earth explored but ultimately not used), Friant on the San Joaquin River and Altus on the North Fork Red River (pumicite) and Bonneville on the Columbia River and Davis on the Colorado River (calcined clay). But Hungry Horse Dam stands out as the first dam constructed using coal combustion fly ash. Utilising 2.4 million cubic metres of concrete, the dam is located on the South Fork Flathead River, one of the tributaries feeding one of the nation's major waterways, the Columbia River, and closely related to the adjacent Glacier National Park. In this respect, Hungry Horse is directly connected to two momentous periods in modern history - the massive adoption in the 1950s of coal as fuel for power plants, and the ongoing threats to fresh water supply and the rapid retreat of alpine glaciers due to global warming. Two concrete cores from this dam, one with fly ash and one without fly ash, are examined microscopically to explore the long-term suppression of alkali-aggregate reaction by fly ash. The core without fly ash exhibits clear evidence of alkali-aggregate reaction, manifested by sandstone coarse aggregate particles with darkened reaction rims. Sandstone coarse aggregate particles of the same lithology in the core with fly ash are without signs of alkali-aggregate reaction. A detailed examination of the darkened rims indicates that alkali-silica reaction products fill the narrow gaps between adjacent sand grains in the sandstone. This alkali-silica gel infilling allows for optical continuity between adjacent sand grains and is responsible for the classic darkened rim associated with the alkali-aggregate reaction.

Distribution of Per- and Polyfluoroalkyl Substances (PFASs) in a Waste-to-Energy Plant─Tracking PFASs in Internal Residual Streams.

Per- and polyfluoroalkyl substances (PFASs) constitute a diverse group of man-made chemicals characterized by their water- and oil-repellent properties and persistency. Given their widespread use in consumer products, PFASs will inevitably be present in waste streams sent to Waste-to-Energy (WtE) plants. We have previously observed a subset of PFASs in residual streams (ashes, treated process water, and flue gas) from a WtE plant. However, the transport and distribution of PFASs inside the WtE plant have remained unaddressed. This study is part of a comprehensive investigation to create a synoptic overview of the distribution of PFASs in WtE residues. PFASs were found in all sample types except for boiler ash. The total levels of 18 individual PFASs (Σ18PFASs) in untreated flue gas ranged from 5.2 to 9.5 ng m-3, decreasing with 35% ± 10% after wet flue gas treatment. Σ18PFASs in the condensate ranged from 46 to 50 ng L-1, of which perfluorohexanoic acid (PFHxA) made up 90% on a ng L-1 basis. PFHxA was also dominant in filter ash, where Σ18PFASs ranged from 0.28 to 0.79 ng g-1. This study shows that flue gas treatment can capture some PFASs and transfer them into WtE residues.

Multimedia Mercury Recovery from Coal-Fired Power Plants Utilizing N-Containing Conjugated Polymer Functionalized Fly Ash.

To recover multimedia mercury from coal-fired power plants, a novel N-containing conjugated polymer (polyaniline and polypyrrole) functionalized fly ash was prepared, which could continuously adsorb 99.2% of gaseous Hg0 at a high space velocity of 368,500 h-1 and nearly 100% of aqueous Hg2+ in the solution pH range of 2-12. The adsorption capacities of Hg0 and Hg2+ reach 1.62 and 101.36 mg/g, respectively. Such a kind of adsorbent has good environmental applicability, i.e. good resistance to coexisting O2/NO/SO2 and coexisting Na+/K+/Ca2+/Mg2+/SO42-. This adsorbent has very low specific resistances (6 × 106-5 × 109 Ω·cm) and thus can be easily collected by an electrostatic precipitator under low-voltage (0.1-0.8 kV). The Hg-saturated adsorbent can desorb almost 100% Hg under relatively low temperature (<250 °C). Characterization and theoretical calculations reveal that conjugated-N is the critical site for adsorbing both Hg0 and Hg2+ as well as activating chlorine. Gaseous Hg0 is oxidized and adsorbed in the form of HgXClX(ad), while aqueous Hg2+ is adsorbed to form a complex with conjugated-N, and parts of Hg2+ are reduced to Hg+ by conjugated-N. This adsorbent can be easily large-scale manufactured; thus, this novel solid waste functionalization method is promising to be applied in coal-fired power plants and other Hg-involving industrial scenes.

Co-pyrolysis of alkali-fused fly ash and corn stover to synthesize biochar composites for remediating lead-contaminated soil.

Fly ash (FA) is mainly composed of silica, alumina, and other metal oxide components, and has a positive stabilizing effect on soil heavy metals. Biochar composites produced from FA and corn stover (CS) can improve its remediation performance. Therefore, a batch of biochar composites (alkali-fused FA-CS biochars, ABs), synthesized via co-pyrolysis of CS and alkali-fused FA (AFFA) at different temperatures of 300, 500, and 700 °C (AB300-1, AB500-1, and AB700-1) and CS to AFFA mass ratios of 10:1, 10:2, and 10:5 (AB500-1, AB500-2, and AB500-5), was used to remediate lead (Pb)-contaminated soil. Compared with pristine biochars (BCs), ABs were enriched with oxygen-containing functional groups (Si-O-Si and Si-O) and aromatic structures. The ABs prepared at lower pyrolytic temperature (≤500 °C) and lower ratio of CS to AFFA (10:1) showed higher yield and stability. The contents of Toxicity Characteristic Leaching Procedure (TCLP)-extractable Pb and DTPA-CaCl2-triethanolamine (DTPA)-extractable Pb were generally lower in the soils amended with ABs than BCs. Compared with other ABs such as AB300-1, AB500-2, AB500-5, and AB700-1, the soil amended with AB500-1 had lower contents of TCLP and DTPA-extractable Pb (24% reduction), exhibiting superior performance in stabilizing Pb in the soil. The gradual decrease of DTPA-extractable Pb content in the soil with increasing dosage of AB500-1 amendments suggests that AB500-1 facilitated the conversion of bioavailable Pb to the stable and less toxic residual fractions. Specifically, the highest percentage of residual fraction of Pb in soil amended with AB500-1 was 14%. Correlation analyses showed that the soil DTPA-extractable Pb content decreased with the increase of soil pH and cation-exchange capacity (CEC) value. ABs stabilize Pb in the soils mainly via electrostatic attraction, precipitation, cation-π interaction, cation exchange, and complexation. These findings provide insights for producing functionalized biochar composites from industrial waste like FA and biomass waste for remediating the soils polluted by heavy metals.

Resource utilization of medical waste incineration fly ash to activate peroxydisulfate for tetracycline degradation: Synergy between adsorption and PDS activation.

Medical waste incineration fly ash (MWI FA) is classified as a hazardous solid waste. Therefore, the development of recycling technologies to convert MWI FA into useful products is necessary and challenging. In this study, we developed a sustainable approach for preparing a catalyst through the pyrolysis of water-washed MWI FA (WW FA-x, where x corresponds to the pyrolysis temperature). Subsequently, it was applied as a potent peroxydisulfate (PDS) activator to remove tetracycline (TC) from water. The results showed that the WW FA-800 exhibited remarkable adsorption performance as well as highly efficient catalytic activation of PDS, with a 115 mg/g maximum TC adsorption capacity and 93.5% (reaction kinetic rate = 315 µmol/g/h) TC removal within 60 min. A synergistic effect was achieved by adsorption and PDS activation. TC degradation was primarily driven by non-radical (1O2 and electron transfer) processes. WW FA-800 possesses multiple active sites, including defects, π-π*, O-CO groups, Fe0, and Cu(I). Three possible pathways for TC decomposition have been proposed, with the majority of intermediates exhibiting less toxicity than TC. Furthermore, the WW FA/PDS system exhibited an excellent anti-interference ability, and universality in the degradation of various organic contaminants. Notably, energy consumption was minimal, approximately 2.80 kWh/(g·TC), and the leachability of heavy metals in the WW FA-800 was within acceptable limits. This study provides a MWI FA recycling route for the development of highly active catalysts.

Coal fly ash is a major carbon flux in the Chang Jiang (Yangtze River) basin.

Fly ash-the residuum of coal burning-contains a considerable amount of fossilized particulate organic carbon (FOCash) that remains after high-temperature combustion. Fly ash leaks into natural environments and participates in the contemporary carbon cycle, but its reactivity and flux remained poorly understood. We characterized FOCash in the Chang Jiang (Yangtze River) basin, China, and quantified the riverine FOCash fluxes. Using Raman spectral analysis, ramped pyrolysis oxidation, and chemical oxidation, we found that FOCash is highly recalcitrant and unreactive, whereas shale-derived FOC (FOCrock) was much more labile and easily oxidized. By combining mass balance calculations and other estimates of fly ash input to rivers, we estimated that the flux of FOCash carried by the Chang Jiang was 0.21 to 0.42 Mt C⋅y-1 in 2007 to 2008-an amount equivalent to 37 to 72% of the total riverine FOC export. We attributed such high flux to the combination of increasing coal combustion that enhances FOCash production and the massive construction of dams in the basin that reduces the flux of FOCrock eroded from upstream mountainous areas. Using global ash data, a first-order estimate suggests that FOCash makes up to 16% of the present-day global riverine FOC flux to the oceans. This reflects a substantial impact of anthropogenic activities on the fluxes and burial of fossil organic carbon that has been made less reactive than the rocks from which it was derived.

A comprehensive review of toxicity of coal fly ash and its leachate in the ecosystem.

Coal fly ash (CFA), a byproduct of coal combustion, is a hazardous industrial solid waste. Its excessive global production, coupled with improper disposal practices, insufficient utilization and limited awareness of its inherent hazards, poses a significant threat to both ecological environment and human health. Based on the physicochemical properties of CFA and its leachates, we elucidate the forms of CFA and potential pathways for its entry into the human body, as well as the leaching behavior, maximum tolerance and biological half-life of toxic elements present in CFA. Furthermore, we provide an overview of current strategies and methods for mitigating the leaching of these harmful elements from CFA. Moreover, we systemically summarize toxic effect of CFA on organisms across various tiers of complexity, analyze epidemiological findings concerning the human health implications resulting from CFA exposure, and delve into the biotoxicological mechanisms of CFA and its leachates at cellular and molecular levels. This review aims to enhance understanding of the potential toxicity of CFA, thereby promoting increased public awareness regarding the disposal and management of this industrial waste.

Dysfunction of Nrf2-regulated cellular defence system and JNK activation induced by high dose of fly Ash particles are associated with pulmonary injury in mouse lungs.

The mechanisms of the exposure to fine particulate matter (PM) as a risk factor for pulmonary injury are not fully understood. The transcription factor, NF-E2-related factor 2 (Nrf2), plays a key role in protection lung against PM insult and cancer chemoprevention. In this study, F3-S fly ash particles from a municipal waste incinerator were evaluated as a PM model. We found that F3-S triggered hierarchical oxidative stress responses involving the prolonged activation of the cytoprotective Nrf2 transcriptional program via Keap1 Cys151 modification, and c-Jun NH2-terminal kinase (JNK) phosphorylation at higher doses. In mouse lungs exposed to fly ash particles at a low dose (10-20 mg/kg), Nrf2 signalling was upregulated, while in those exposed to a high fly ash particle dose (40 mg/kg), there was significant activation of JNK, and this correlated with Nrf2 phosphorylation and the downregulation of antioxidant response element (ARE)-driven genes. The JNK inhibitor, SP600125, reversed Nrf2 phosphorylation, and downregulation of detoxifying enzymes. Silencing JNK expression in mouse lungs using adenoviral shRNA inhibited JNK activation and Nrf2 phosphorylation, promoted ARE-driven gene expression, and reduced pulmonary injury. Furthermore, we found that the 452-515 amino acid region within the Neh1 domain of Nrf2 was required for its interaction with P-JNK. We demonstrated that Nrf2 was an important P-JNK target in fly ash-induced pulmonary toxicity. JNK phosphorylated Nrf2, leading to a dysfunction of the Nrf2-mediated defence system.

Assessment of medicinal plants colonizing abundantly on metal-enriched fly ash deposits: phytoremediation prospective.

Heavy metal-enriched fly ash (FA) deposits are recognized as hazardous contaminated sites on the earth, which pollute our ecosystems. Consequently, the present investigation was carried out to explore the phytoremediation potential of naturally growing medicinal plants in the FA dumpsite. This present study chose two native medicinal plants i.e., Bacopa monnieri and Acmella oleracea found to be naturally colonizing abundantly on FA dumpsite to assess heavy metal accumulation. FA sample of B. monnieri thriving sites found to have metal content in order Mn (216.6)> Cr (39.27)> Zn (20.8)> Ni (16.1)> Cu (15.03)> Co (6.7)> Pb (5.43) whereas for A. oleracea FA dumpsites, the order of metal availability was Mn (750.3)> B (54.5)>Cr (37.2)>Zn (31.33)> Cu (18.7)> Ni (16.93)> Co (7.7)>Pb (4.23). In B. monnieri, higher concentrations of Cr and Mn were observed in the shoot in comparison to the root, indicative of its potential as a hyperaccumulator plant. Conversely, in A. oleracea, greater amounts of Pb were detected in the shoot relative to the root. Hence, it is recommended that B. monnieri and A. oleracea grow on such heavy metal-enriched substrates should be avoided for medicinal purposes; however, these plants can be used for phytoremediation purposes.

Fly ash phytoremediation through natural colonizer plant species is limited.Native colonizing plant species on fly ash has a pivotal role in phytoremediation.Naturally colonizing medicinal plants were dominant over the Fly ash dumpsites.Bacopa monnieri and Acmella oleracea have phytoremediation potential on fly ash.Indeed, fly ash-grown medicinal plants should not be used by local communities.

Assessment of phytodiversity and phytoremediation potential of plants in the vicinity of a thermal power plant.

A study was carried out to evaluate phytodiversity along with the metal accumulation potential of native plants growing in the vicinity of a thermal power plant (TPP). We documented 26 tree species, six shrubs, and 35 herbs. Importance value index (IVI), which measures the extent to which a species dominates in an area, was found highest for Senna siamea (95.7) followed by Tectona grandis (56.5), and Pithecellobium dulce (19.6). Soil was acidic (pH 5.4) in nature with higher concentrations of Al and Fe. The pH of ground water was found acidic while pH of nearby river was found slightly alkaline. Values of PM2.5 and PM10 were slightly higher than NAAQS standards for industrial areas. The concentration of metals was found higher in aquatic plants than in terrestrial plants. In general, herbs and shrubs showed more metal accumulation potential than trees. Our results suggest that Senna siamea could be used for revegetation purposes in FA landfills. Further, terrestrial and aquatic plants such as Ageratina adenophora and Stuckenia pectinata could be used for reclamation of Mn, Zn, Al, and Fe from contaminated soils. Hydrilla verticillata (Ni and Mn), Nelumbo nucifera, and Ipomoea aquatica (Cr) can be used for metal removal from contaminated water.

The study focuses on the assessment of phytodiversity, soil and water analysis, ambient air quality, and bioaccumulation of heavy metals in plants growing in and around a thermal power plant. The study assumes significance as more than 65% of India's electricity generation is still by coal-fired power plants, having major implications for air, soil, and water pollution. By selecting native plant species adapted to the region, we can enhance biodiversity, restore habitats, and contribute to the overall ecological health of the area surrounding the power plant.

Phytostabilization of fly ash from a coalmine in Botswana and biovalorisation of the recovered Napier grass (Pennisetum purpureum Schumach.).

The disposal of fly ash (FA) from coal power plants polluting the air, soil, and groundwater is a major environmental concern. Phytoremediation to rehabilitate fly ash dumpsites is a promising alternative but has practical concerns about the disposal of harvested biomass. This study investigated the effect of supplementing fly ash with fresh sewage sludge (FSS), aged sewage sludge, food waste, and compost (COM) to enhance the phytoremediation potential of Napier grass and its subsequent utilization for ethanol production. The highest removal of Mn (1196.12 g ha-1) and Ni (128.06 g ha-1) from FA could be obtained when Napier is grown in the presence of FSS and inorganic fertilizer (NPK). In addition, the highest bioethanol yield (19.31 g L-1) was obtained from Napier grown in fly ash with COM + NPK, thus providing additional economic benefits aside from the remediation process. Given the significant levels of heavy metals present in the pulp and bio-slurry after ethanol production, further research is required in this area to determine the best ways to utilize this waste such as converting it into biochar.

Using energy crops as a phytoremediation agent for fly ash dumpsites has the potential to remediate heavy metal contamination and provide additional economic benefits. Napier grass was able to tolerate high concentrations of heavy metals and yield high biomass in fly ash in the presence of organic amendments. The harvested biomass was successfully converted into substrate for bioethanol production using heavy metal-tolerant yeast. This is the first report on the production of ethanol from the phytoremediation biomass of Napier grass.

Influence of Coal-Fired Fly Ash on Measurement Error of NO2 Electrochemical Sensors.

To overcome the limitations of NO2 electrochemical sensors, including their inaccurate measurements and short working life, when used around coal-fired power plants, we investigated the influence of coal-fired fly ash deposition on the measurement error of NO2 electrochemical sensors through experimental tests. The morphological characteristics and pellet diameter distribution of coal-fired fly ash pellets were determined via scanning electron microscopy. The sedimentation velocity of coal-fired fly ash pellets in the air was determined through theoretical calculations of aerodynamics and hydrodynamics. Additionally, the effect of the deposition of coal-fired fly ash on the measurement error of NO2 electrochemical sensors was determined through experimental tests. The test results show that the minimum and maximum measurement errors of the NO2 electrochemical gas sensor were 8.015% and 30.35%, respectively, after a deposition duration of 30 days with 30 mg/m3 coal-fired fly ash. This demonstrates that coal-fired fly ash deposition is the cause of the inaccurate measurements and short working life of these sensors. Coal-fired fly ash causes a decrease in the gas diffusion area of the sensor and the diffusion coefficient, thus increasing the sensor measurement error.

Life cycle GHG emissions assessment of vanadium recovery from bitumen-derived petcoke fly ash.

Petcoke generated during bitumen upgrading is a potential source of vanadium for the global market. Recovering vanadium from the fly ash originating from the combustion of petcoke appears to be a suitable route for commercial implementation, given its high extraction rate. Although the technical feasibility of the recovery process has been proven, the environmental impact should be addressed. Information on the greenhouse (GHG) emissions from the process is scarce in the public domain. Therefore, a framework was developed for assessment of life cycle GHG emissions for extraction of vanadium from petcoke-based fly ash. This framework was used to perform a life cycle GHG emissions assessment of a water leaching and salt roasting process to extract vanadium from fly ash. For the upstream GHG emissions, we collected direct emissions data and energy consumption from the literature, and, for the process emissions, we developed a model to estimate energy and material balances based on process conditions. The emission factors for electricity production, fuel combustion, production of consumables, and gas treatment were used to obtain the life cycle GHG emissions. The results show that the life cycle GHG emission of vanadium recovery are 26.6-3.9+0.9 kg CO2eq/kg V2O5; 66% of these are direct GHG emissions. The process GHG emissions from fly ash decarbonization contribute the most to the life cycle GHG emissions. The air-to-fuel ratio for roasting and the GHG emission factors for petcoke combustion and the gas treatment operation are the inputs that most effect the model output. Compared with the production of V2O5 from vanadium titano-magnetite ore and bitumen upgrading spent catalyst, the petcoke fly ash pathway generates about twice the life cycle GHG emissions. This study's results can help determine areas of improvement in the upstream operations and the recovery process to reduce the life cycle GHG emissions to levels that can compete with primary and alternative routes to produce vanadium pentoxide. The results of this study can help in decision-making associated with vanadium extract from fly ash produced from combustion of petcoke.

Research on oxygen enrichment for municipal solid waste fly ash melting: A pilot-scale study on natural gas and coal as the melting fuel.

High energy consumption is the main obstacle of melting/vitrification technology for the disposal of municipal solid waste incineration fly ash (MSWIFA) for industrial applications. To reduce energy consumption and lower operating costs, oxygen enrichment melting was proposed and studied in this work. This research was conducted in a pilot-scale melting furnace, and three melting conditions were compared and discussed. The results showed that 66% of natural gas was saved and the operating cost was reduced by 55% when oxygen enrichment technology was applied to MSWIFA melting. When coal was used as the fuel with the oxygen enrichment melting technology, the operating cost was even lower at 66.39 dollar/ton of fly ash. Because MSWIFA was a Ca-rich material, the relatively high content of Si and Al in the coal fly ash promoted the formation of vitrificated slag, leading to a reduction in the overall pollution toxicity index (OPTI) of MSWIFA by 99.98%. Meanwhile, SO2, HCl, and secondary fly ash were the main pollutants during MSWIFA melting, and when coal was used as the fuel, the emissions of SO2 and HCl could be reduced and the OPTI of secondary fly ash was suppressed. These results suggested that to obtain the lowest operating cost and reduce secondary pollution during MSWIFA melting, the best option consisted of oxygen enrichment technology with coal as the fuel.

Transformation behavior of heavy metal during Co-thermal treatment of hazardous waste incineration fly ash and slag/electroplating sludge.

In this study, the behavior of heavy metal transformation during the co-thermal treatment of hazardous waste incineration fly ash (HWIFA) and Fe-containing hazardous waste (including hazardous waste incineration bottom slag (HWIBS) and electroplating sludge (ES)) was investigated. The findings demonstrated that such a treatment effectively reduced the static leaching toxicity of Cr and Pb. Moreover, when the treatment temperature exceeded 1000 °C, the co-thermal treated sample exhibited low concentrations of dynamically leached Cr, Pb, and Zn, indicating that these heavy metals were successful detoxified. Thermodynamic analyses and phase transformation results suggested that the formation of spinel and the gradual disappearance of chromium dioxide in the presence of Fe-containing hazardous wastes contributed to the solidification of chromium. Additionally, the efficient detoxification of Pb and Zn was attributed to their volatilization and entry into the liquid phase during the co-thermal treatment process. Therefore, this study sets an excellent example of the co-thermal treatment of hazardous wastes and the control of heavy metal pollution during the treatment process.

Analysis of composition characteristics and treatment techniques of municipal solid waste incineration fly ash in China.

The rapid development of the economy and society is causing an increase in the amount of municipal solid waste (MSW) produced by people's daily lives. With the strong support of the Chinese government, incineration power generation has steadily become the primary method of treating MSW, accounting for 79.86%. However, burning produces a significant amount of municipal solid waste incineration fly ash (MSWI-FA), which contains heavy metals, soluble chlorine salts, and dioxins. China's MSWI-FA yield increased by 8.23% annually to 7.80 million tons in 2022. Besides, the eastern region, especially the southeastern coastal region, has the highest yield of MSWI-FA. There are certain similarities in the chemical characteristics of MSWI-FA samples from Northeast, North, East, and South China. Zn and CaO have the largest amounts of metals and oxides, respectively. The Cl content is about 20 wt%. This study provides an overview of the techniques used in the thermal treatment method, solidification and stabilization, and separation and extraction of MSWI-FA and compares their benefits and drawbacks. In addition, the industrial applications and standard requirements of landfill treatment and resource utilization of MSWI-FA in China are analyzed. It is discovered that China's resource utilization of MSWI-FA is insufficient through the study on the fly ash disposal procedures at a few MSW incineration facilities located in the economically developed Guangdong Province and the traditional industrial city of Tianjin. Finally, the prospects for the disposal of MSWI-FA were discussed.

Preparation of functional geopolymers from municipal solid waste incineration fly ash: An approach combining experimental and computational simulation studies.

This study aims to evaluate the feasibility and safety of using municipal solid waste incineration fly ash (MSW-IFA) in the development of geopolymer-based solidification/stabilization (S/S) treatments. Geopolymers have garnered attention as a sustainable alternative to traditional cement, owing to their high strength, stability, and minimal CO2 emissions. In this study, a combination of experimental and simulation calculations was used to investigate the setting time, mechanical properties, environmental risks, hydration mechanisms and processes of municipal solid waste incineration fly ash-based polymeric functional cementitious materials (GFCM). The results demonstrate that the mechanical properties of GFCM are related to the changes in the mineral phases and the degree of compactness. Quantum chemical calculations indicate that the hydration products may be [Si(OH)4], [Al(OH)3(OH2)] and [Al(OH)4]-. It is possible that the heavy metals are embedded in the hydrated silica-aluminate by electrostatic interaction or chemisorption. Heavy metals may be embedded in hydrated silica-aluminate by electrostatic action or chemisorption. This study provides a feasible method for resource utilization and heavy metal stabilization mechanism of MSW-IFA.

Resource utilization of MSWI fly ash supporting TiO2/BiOCl nanocomposite for enhanced photocatalytic degradation of sodium isopropyl xanthate: Mechanism and performance evaluation.

The removal of organic pollutants in water environments and the resource utilization of solid waste are two pressing issues around the world. Facing the increasing pollution induced by discharge of mining effluents containing sodium isopropyl xanthate (SIPX), in this work, municipal solid waste incineration fly ash (MSWI FA) was pretreated by hydrothermal method to produce stabilized FA, which was then innovatively used as support for the construction of FA/TiO2/BiOCl nanocomposite (FTB) with promoted photocatalytic activity under visible light and natural sunlight. When the content of FA was 20 wt% and the mass ratio of TiO2 to BiOCl was 4:6, a remarkable performance for the optimal FTB (20-FTB-2) was achieved. Characterizations demonstrated that TiO2 and BiOCl uniformly dispersed on FA contributing to high surface area and broad light adsorption of FTB, which exhibits excellent adsorption capacity and light response ability. Build in electric field formed in the interface of TiO2/BiOCl heterojunction revealed by density functional theory calculations accelerated the separation of photoinduced e- and h+, leading to high efficiency for SIPX degradation. The synergetic effect combined with adsorption and photocatalytic degradation endowed 20-FTB-2 superior SIPX removal efficiency over 99% within 30 min under visible light and natural sunlight irradiation. The photocatalytic degradation pathways of SIPX were determined through theoretical calculations and characterizations, and the toxic byproduct CS2 was effectively eliminated through oxidation of •O2-. For 20-FTB-2, reusability of photocatalyst was showed by cycle tests, also the concentrations of main heavy metals (Pb, Zn, Cu, Cr, and Cd) in the liquid phases released during photocatalyst preparation process (< 1 mg/L) and photodegradation process (< 8.5 µg/L) proved the satisfactory stability with low toxicity. This work proposed a novel strategy to develop efficient and stable support-based photocatalysts by utilizing MSWI FA and realize its resource utilization.

Evolution of physicochemical and leaching characteristics of municipal solid waste incineration fly ash in China under ultra-low emission standard.

The physical and chemical characteristics of fly ash has changed significantly under ultra-low emission system and the current leaching system is no longer suitable for high alkalinity fly ash. This work investigated the pH values and evolution of physical and chemical characteristics of fly ash from 24 typical municipal solid waste incineration plants in China. The pH value of the leaching solution obtained by HJ/T 300-2007 presented two different acid and alkali characteristics, where high and low alkalinity fly ash accounted for 54.17% and 45.83%, respectively. The alkali content in fly ash increased significantly after ultra-low emission standard, increasing by 18.24% compared with before the implementation of GB 18485-2014. The leaching behavior of high alkalinity fly ash showed the illusion that they could enter the landfill only by the addition of a small amount of chelating agent or even without stabilization treatment, and its long-term landfill risk is significant. The phase change of high alkalinity fly ash and pH value change of the leaching solution after carbonation were the key factors for the leaching concentration change of heavy metals. Therefore, it is recommended to improve the existing leaching system or conduct accelerated carbonization experiments to scientifically evaluate the long-term leaching characteristics of high alkalinity fly ash, and to reduce the risk of heavy metal release from high alkalinity FA after entering the landfill site.