Achieving a Noise Limit with a Few-layer WSe2 Avalanche Photodetector at Room Temperature.

We engineered a two-dimensional Pt/WSe2/Ni avalanche photodetector (APD) optimized for ultraweak signal detection at room temperature. By fine-tuning the work functions, we achieved an ultralow dark current of 10-14 A under small bias, with a noise equivalent power (NEP) of 8.09 fW/Hz1/2. This performance is driven by effective dark barrier blocking and a record-long electron mean free path (123 nm) in intrinsic WSe2, minimizing dark carrier replenishment and suppressing noise under an ultralow electric field. Our APD exhibits a high gain of 5 × 105 at a modulation frequency of 20 kHz, effectively balancing gain and bandwidth, a common challenge in traditional photovoltaic-based APDs. By addressing the typical challenges of high noise and low gain and minimizing dependence on high electric fields, this work highlights the potential of 2D materials in developing efficient, low-power, and ultrasensitive photodetections.

Analytical Photoresponses of Gated Nanowire Photoconductors.

Low-dimensional photoconductors have extraordinarily high photoresponse and gain, which can be modulated by gate voltages as shown in literature. However, the physics of gate modulation remains elusive. In this work, the physics of gate modulation in silicon nanowire photoconductors with the analytical photoresponse equations is investigated. It is found that the impact of gate voltage varies vastly for nanowires with different size. For the wide nanowires that cannot be pinched off by high gate voltage, it is found that the photoresponses are enhanced by at least one order of magnitude due to the gate-induced electric passivation. For narrow nanowires that starts with a pinched-off channel, the gate voltage has no electric passivation effect but increases the potential barrier between source and drain, resulting in a decrease in dark and photocurrent. For the nanowires with an intermediate size, the channel is continuous but can be pinched off by a high gate voltage. The photoresponsivity and photodetectivity is maximized during the transition from the continuous channel to the pinched-off one. This work provides important insights on how to design high-performance photoconductors.

A Critical Analysis of Quadratic Boost Based High-Gain Converters for Electric Vehicle Applications: A Review.

Conventional DC-DC boost converters have played a vital role in electric vehicle (EVs) powertrains by enabling the necessary voltage to increase to meet the needs of electric motors. However, recent developments in high-gain converters have introduced new possibilities with enhanced voltage amplification capabilities and efficiency. This study discusses and evaluates the state-of-the-art high-gain DC-DC converters for EV applications based on the Quadratic Boost Converter (QBC). Research into innovative topologies has increased in response to the increasing demand for efficient and high-performance power electronic converters in the rapidly expanding EV industry. Due to its ability to provide more significant voltage gains than conventional boost converters, the QBC has become a viable option for meeting the unique requirements of EV power systems. This survey focuses on the efficiency, power density, and overall performance parameters of QBC-based high-gain converters. The literature review provides a foundation for comprehending power electronics converters' trends, challenges, and opportunities. The acquired knowledge can enhance the design and optimization of high-gain converters based on the QBC, thereby fostering more sustainable and efficient power systems for the expanding electric mobility industry. In the future, the report suggests that investigating new high-gain converter design methodologies will reduce component stress and enhance the intact system efficiency.

A Wideband High Gain Differential Patch Antenna Featuring In-Phase Radiating Apertures.

Communication systems need antennas with wide bandwidths to provide large throughput, while imaging radars benefit from high gain for increased range and wide bandwidths for high-resolution imaging. This paper presents the design and evaluation of a wideband, high-gain antenna that achieves an average gain of 9.7 dBi over a bandwidth of 1.49 GHz to 3.92 GHz by using multiple in-phase radiating apertures. The antenna has a unique structure with a central rectangular short-circuited patch sandwiched between two back-to-back U-shaped radiating patches and two flanking H-shaped short-circuited patches. Each of the U-shaped patches employs a coplanar waveguide as feeding to achieve ultra-wideband impedance matching. Benefiting from design arrangement, in-phase electrical field distributions appear at the gaps between the patches that result in equivalent radiating magnetic currents in the same direction. Theory analysis shows that the close-spaced, same-direction magnetic currents created by the radiating apertures intensify the radiation and increase antenna gain within its impedance bandwidth. Simulated data show that the use of the coplanar waveguide feeding and short-circuited patches increase the bandwidth from 65 MHz to 2.43 GHz. Moreover, the short-circuited patches increase the gain by 3.45 dB at 2.4 GHz. Simulation and measurement results validate the design and show that the antenna features a maximum gain of 11.3 dBi and an average gain of 9.7 dBi in a fractional bandwidth of 89.8%. Because of the high gain values and the wide bandwidth, the antenna is particularly suited for long-range communication systems and high-resolution radar applications.

Robust Output Feedback Stabilization and Tracking for an Uncertain Nonholonomic Systems with Application to a Mobile Robot.

This paper presents a novel robust output feedback control that simultaneously performs both stabilization and trajectory tracking for a class of underactuated nonholonomic systems despite model uncertainties, external disturbance, and the absence of velocity measurement. To solve this challenging problem, a generalized normal form has been successfully created by employing an input-output feedback linearization approach and a change in coordinates (diffeomorphism). This research mainly focuses on the stabilization problem of nonholonomic systems that can be transformed to a normal form and pose several challenges, including (i) a nontriangular normal form, (ii) the internal dynamics of the system are non-affine in control, and (iii) the zero dynamics of the system are not in minimum phase. The proposed scheme utilizes combined backstepping and sliding mode control (SMC) techniques. Furthermore, the full-order high gain observer (HGO) has been developed to estimate the derivative of output functions and internal dynamics. Then, full-order HGO and the backstepping SMC have been integrated to synthesize a robust output feedback controller. A differential-drive type (2,0) the wheeled mobile robot has been considered as an example to support the theoretical results. The simulation results demonstrate that the backstepping SMC exhibits robustness against bounded uncertainties.

A Compact Dual-Polarized Vivaldi Antenna with High Gain for Tree Radar Applications.

A dual-polarized compact Vivaldi antenna with high gain performance is proposed for tree radar applications. The proposed design introduces an array configuration consisting of two pairs of two Vivaldi elements to optimize the operating bandwidth and gain while providing dual-polarization capability. To enhance the gain of the proposed antenna over a certain frequency range of interest, directors and edge slots are incorporated into each Vivaldi element. To further enhance the overall antenna gain, a metal back reflector is used. The measurement results of the fabricated antenna show that the proposed antenna achieves a high gain of 5.5 to 14.8 dBi over broadband from 0.5 GHz to 3 GHz. Moreover, it achieves cross-polarization discrimination larger than 20 dB, ensuring high polarization purity. The fabricated antenna is used to detect and image the defects inside tree trunks. The results show that the proposed antenna yields a better-migrated image with a clear defect region compared to that obtained by a commercial Horn antenna.

Shortwave Infrared Photodetection with oCVD Polythiophene.

Shortwave infrared (SWIR, λ = 1-3 µm) photodetectors typically use compound semiconductors that are fabricated using high-temperature epitaxial growth and require active cooling. New technologies that overcome these constraints are the focus of intensive current research. Herein, oxidative chemical vapor deposition (oCVD) is used for the first time to create a room temperature, vapor-phase deposited SWIR photoconductive detector with a unique tangled wire film morphology that detects nW-level photons emitted from a 500 °C cavity blackbody radiator-a rarity for polymer systems. A new, window-based process that greatly simplifies device fabrication is used to construct doped polythiophene-based SWIR sensors. The detectors feature an 8.97 kΩ dark resistance and are limited by 1/f noise. They feature an external quantum efficiency (gain-external quantum efficiency) product of 395% and have a measured specific detectivity (D*) of 106 Jones, with the potential to reach D* = 1010 Jones after 1/f noise is minimized. Still, the measured D* is only a factor of 102 lower than a typical microbolometer and after optimization, the newly described oCVD polymer-based IR detectors will be in a category competitive with commercially available, room temperature lead salt photoconductors and within reach of room temperature photodiodes.

Design of Wideband High-Gain Patch Antenna Array for High-Temperature Applications.

A low-profile, wideband, and high-gain antenna array, based on a novel double-H-shaped slot microstrip patch radiating element and robust against high temperature variations, is proposed in this work. The antenna element was designed to operate in the frequency range between 12 GHz and 18.25 GHz, with a 41.3% fractional bandwidth (FBW) and an obtained peak gain equal to 10.2 dBi. The planar array, characterized by a feed network with a flexible 1 to 16 power divider, comprised 4 × 4 antenna elements and generated a pattern with a peak gain of 19.1 dBi at 15.5 GHz. An antenna array prototype was fabricated, and the measurements showed good agreement with the numerical simulations as the manufactured antenna operated in the range of 11.4-17 GHz, with a 39.4% FBW, and the peak gain at 15.5 GHz was 18.7 dBi. The high-temperature simulated and experimental results, performed in a temperature chamber, demonstrated that the array performance was stable in a wide temperature range, from -50 °C to 150 °C.

Low-Profile Dual-Band Reflector Antenna for High-Frequency Applications.

A high-gain low-profile reflector antenna with dual-band radiation ability is presented in this paper. The antenna achieves a relative 2 dB gain bandwidth of 10% around fl, and a relative 2 dB gain bandwidth of 20%, around fh, where fl and fh are the center operating frequencies of the frequency bands of 29.4~32.4 GHz and 142~174 GHz, respectively. To achieve the dual-band radiation ability, a composite dual-band feed with an fh/fl ratio of around 5 is proposed as the feed for the reflector antenna, which includes a higher-band circular waveguide and a lower-band coaxial horn. The metallic elliptical surface serves as the subreflector (SR) in the higher band, while the SR is the planar reflectarray in the lower band. Due to the design of the dual reflector, the dual-band reflector antenna features a low focal-to-diameter (F/D) ratio of approximately 0.2. According to the simulated results, the proposed reflector antenna achieves efficiencies of 59.0% and 42.9% at fl and fh, respectively. For verification purposes, a Ku/E-band scaled prototype is manufactured. The measured VSWRs, radiation patterns, and gains are in reasonable agreement with the simulated ones, proving the correctness of the proposed design method.

High Gain Flat-Panel mmWave Antenna Array.

In the realm of mmWave communication and connectivity, integrating chips and antennas into a cohesive system is paramount. Given this, planar antenna arrays have become indispensable. In this article, we introduce a novel antenna array tailored for mmWave applications, characterized by its high directivity. Distinctively, this new array employs a flat-panel radiator, ensuring an augmented gain without necessitating additional superstrate layers. To validate its potency, a 4 × 4 flat-panel array with dimensions of 3.74 λ0 × 3.74 λ0 × 0.106 λ0 at 28 GHz including a ground plane was designed and tested for n257 band. The standalone array element exhibited a bandwidth of 20.6%, centered at 28.5 GHz. Furthermore, a 1 × 16 mmWave feed network was designed and amalgamated with the array elements to assess the comprehensive antenna performance. The measured peak gain of 21.3 dBi at 28.5 GHz was observed with the measured half power beamwidth of 15° while the gain variation within the operation band was less than 3 dB.

Four-Port 38 GHz MIMO Antenna with High Gain and Isolation for 5G Wireless Networks.

In this paper, a 38 GHz 4-port multiple-input multiple-output (MIMO) antenna with considerable isolation and gain enhancement for 5G applications is introduced. The suggested antenna element is a monopole antenna composed of a circular patch with a rectangular slot etched from it and a partial ground plane is used to extend the desired frequency to operate from 36.6 GHz to 39.5 GHz with a center frequency of 38 GHz. The high isolation is achieved by arranging the four elements orthogonally and adding four stubs to reduce mutual coupling between elements at the desired frequency bands. The gain improvement is also introduced by placing a frequency selective structure (FSS) which is designed at the same frequency bands of the antenna under the suggested MIMO antenna to act as a reflector. The proposed four-element MIMO with the FSS prototype is built and tested in order to confirm the simulated results. The suggested antenna operated from 37.2 GHz to 39.2 GHz with an isolation of less than 25 dB across the obtained frequency range. The peak gain of the antenna is enhanced from 5.5 dBi to around 10 dBi by utilizing the FSS structure; furthermore, the back radiation is enhanced. The MIMO performance is validated by extracting its parameters and comparing with the simulated results. The results extracted from the simulation and the measurement show satisfactory matching along with the target band, indicating that the proposed structure could be used for 5G communications.

High-Gain Millimeter-Wave Beam Scanning Transmitarray Antenna.

In this article, a high-gain millimeter-wave transmitarray antenna (TAA) maintaining scanning ability is developed, integrating an array feed as the primary emitter. The work is achieved within a limited aperture area, avoiding the replacement or extension of the array. The addition of a set of defocused phases along the scanning direction to the phase distribution of the monofocal lens allows the converging energy to be dispersed into the scanning scope. The beam forming algorithm proposed in this article can determine the excitation coefficients of the array feed source, and is beneficial to improve the scanning capability in array-fed transmitarray antennas. A transmitarray based on the square waveguide element illuminated by an array feed is designed with a focal-to-diameter ratio (F/D) of 0.6. A 1-D scan with a scope of -5° to 5° is realized through calculation. The measured results show that the transmitarray can achieve a high gain, 37.95 dBi at 160 GHz, although a maximum 2.2 dB error appears compared with the calculation in the operating band of 150-170 GHz. The proposed transmitarray has been proven to generate scannable high-gain beams in the millimeter-wave band and is expected to demonstrate its potential in other applications.

A Single-Fed Wideband Circularly Polarized Cross-Fed Cavity-Less Magneto-Electric Dipole Antenna.

In this paper, we proposed a new wideband circularly polarized cross-fed magneto-electric dipole antenna. Different from conventional cross-dipole or magneto-electric dipole antennas, the proposed simple geometry realizes a pair of complementary magnetic dipole modes by utilizing the two open slots formed between the four cross-fed microstrip patches for achieving circular polarization and high stable gain across a wide frequency band. No parasitic elements are required for extending the bandwidths; therefore, both the radiation patterns and in-band gain are stable. The simulated field distributions demonstrated the phase complementarity of the two pairs of magnetic and electric dipole modes. A parametric study was also performed to demonstrate the radiation mechanism between the electric and magnetic dipole modes. The radiating elements are realized on a piece of double-sided dielectric substrate fed and mechanically supported by a low-cost commercial semirigid cable. The overall thickness of the antenna is about 0.22λo at the center frequency of axial ratio bandwidth. The measured results show a wide impedance bandwidth (|S11| < -10 dB) of 70.2% from 2.45 to 5.10 GHz. The in-band 3-dB axial ratio bandwidth is 51.5% from 3.0 to 5.08 GHz. More importantly, the gain of the antenna is 9.25 ± 0.56 dBic across the 3-dB axial ratio bandwidth.

Partial Discharge Wideband Full-Band High-Gain Resonant Cavity UHF Sensor Research.

To meet the real demand for broadband full-band high-gain antenna sensors in the process of partial discharge (PD) Ultra-High frequency (UHF) detection test and online monitoring of power equipment, this paper builds a resonant cavity monopole UHF antenna sensor based on Fabry-Perot resonant cavity antenna technology, conducts the sensor Voltage Standing Wave Ratio (VSWR) optimization study using curved flow technology, conducts the sensor gain optimization study using slot dual resonant structure, and, finally, tests the sensor performance using the built PD detection test platform. The resonant cavity monopole antenna exhibits outstanding VSWR performance in the frequency range of 0.37 GHz-3 GHz, according to simulation and test data: the average gain in the frequency range of 0.3 GHz-3 GHz is 4.92 dBi, and the highest gain at the primary resonant frequency of 1.0 GHz is 7.16 dBi, with good radiation performance over the whole frequency spectrum. The electromagnetic pulse signal sensed by the UHF sensor developed in this paper can demonstrate the energy spectrum distribution characteristics of PD radiation electromagnetic wave signal more comprehensively, laying a firm technical foundation for thoroughly understanding the electromagnetic wave radiation characteristics of various types of PD insulation defects of various power equipment and the selection of a specific direction for its supporting optimization.

Organic Amine-Bridged Quasi-2D Perovskite/PbS Colloidal Quantum Dots Composites for High-Gain Near-Infrared Photodetectors.

Near-infrared (NIR) II detection at weak flux intensity is required in medical imaging and is especially urgent in light of the low quantum efficiency of NIR-II dyes. The low responsivity of traditional photodetectors in this region limits image quality. Here, we report a NIR-II photodetector with high gain based on perovskite coupled PbS colloidal quantum dots (CQDs). Tailoring the trap density of CQDs by designing surface ligands with dual functionality contributed to control over trap-induced charge-injection upon light illumination. As a result, a detector with high gain is realized, showing external quantum efficiency of 1260% at 1200 nm and achieving the lowest detectable light intensity, that is, as low as 0.67 pW cm-2 with a linear dynamic range of 200 dB. Devices maintain over 90% of responsivity after 150 days of storage. We acquired images of a butterfly wing, showing the skeleton texture with a maximum spatial resolution of 3.9 lp/mm.

Electronic Beam-Scanning Antenna Based on a Reconfigurable Phase-Modulated Metasurface.

Metasurfaces (MSs) have enabled the emergence of new ideas and solutions in the design of antennas and for the control of electromagnetic waves. In this work, we propose to design a directional high-gain reconfigurable planar antenna based on a phase-modulated metasurface. Reconfigurability is achieved by integrating varactor diodes into the elementary meta-atoms composing the metasurface. As a proof of concept, a metasurface prototype that operates around 5 GHz is designed and fabricated to be tested in an antenna configuration. The metasurface is flexibly controlled by different bias voltages applied to the varactor diodes, thus allowing the user to control its phase characteristics. By assigning judiciously calculated phase profiles to the metasurface illuminated by a feeding primary source, different scenarios of far-field patterns can be considered. Different phase profiles are tested, allowing us to, firstly, achieve a highly directive boresight radiation and, secondly, to steer the main radiated beam towards an off-normal direction. The whole design process is verified by numerical simulations and is validated experimentally by far-field antenna measurements. The proposed metasurface enables the design of directive flat antennas with beam-scanning characteristics without complex feeding systems and power-consuming phase shifters, and thus provides potential interests for next generation antenna hardware.

Design of Broadband High-Gain Fabry-Pérot Antenna Using Frequency-Selective Surface.

In this paper, a broadband high-gain Fabry−Pérot (F-P) antenna composed of the air-loaded slot-coupled broadband microstrip antenna and the frequency selective surface (FSS) based positive gradient reflection phase structure is proposed. Taking advantage of the superposition effect of multiple reflections and transmissions occurring between layer structures, the gain enhancement was realized. Meanwhile, by cascading the single-layer FSS and the dielectric substrate, the positive gradient reflection phase over a wider frequency range was achieved. Simulated results show that the resonant frequency of the designed F-P antenna is 10 GHz, the impedance matching band (S11 < −10 dB) ranges from 8.3 GHz to 11.25 GHz with a bandwidth of 29.5%, and the antenna gain is improved significantly in the range of 8.1 GHz~11.25 GHz with a gain bandwidth of 31.5%. For further verification, a prototype was fabricated, and the experimental and simulated results are in good agreement.

A Novel Circularly Polarized Folded Transmitarray Antenna with Integrated Radiation and Scattering Performance.

In this paper, a novel design method of circularly polarized folded transmitarray antenna (CPFTA) is presented by applying sequential rotation technology. Compared with the general design method, the novel design method can reduce the design difficulty and improve the axis ratio (AR) bandwidth significantly without adding any additional structure. To verify the proposed method, both a general CPFTA (GCPFTA) and a novel CPFTA (NCPFTA) are designed, fabricated, measured and compared. Good agreements between simulated and measured results are obtained. Thanks to the creative design, the integrated radiation and scattering control of the CPFTA is realized for the first time. The proposed NCPFTA has the advantages of broadband, high gain, planar structure, low profile, convenience in installation and low radar cross section (RCS), which has potential application in mobile satellite communication.

A Lens Antenna with Reconfigurable Beams for mmWave Wind Profile Radar.

Wind profile radar systems require antennas with multiple radiation beams for detecting wind velocity, as well as with a low sidelobe and dual polarization for enhancing the sensitivity for the weak signal reflected from the turbulence. This paper proposes a lens antenna operating at 24 GHz with four reconfigurable beams for wind profile radars. This lens antenna includes 2 × 2 corrugated horn antennas for radiating 24 GHz waves in two polarizations, and the dielectric lens for modulating four radiation beams with a high gain and low sidelobe. Experiments demonstrate that this lens antenna can realize reconfigurable beams with deflections of ±15° in dual polarizations, meanwhile with the gain of 30.58 dBi and the sidelobe of -20 dB. This proposed lens antenna can be applied to mmWave wind profile radars of wind turbines for enhancing wind power efficiency.

Design of a mmWave Antenna Printed on a Thick Vehicle-Glass Substrate Using a Linearly Arrayed Patch Director and a Grid-Slotted Patch Reflector for High-Gain Characteristics.

This paper proposes a 5G glass antenna that can be printed on the thick window glass of a vehicle. The proposed antenna consists of a coplanar waveguide (CPW), a printed monopole radiator, parasitic elements, a linearly arrayed patch director, and a grid-slotted patch reflector. The linearly arrayed patch director and grid-slotted patch reflector are applied to improve the bore-sight gain of the antenna. To verify the performance improvement and feasibility, the proposed antenna is fabricated, and a reflection coefficient and a radiation pattern are measured and compared with the simulation results. The measured reflection coefficient shows broadband characteristics of less than -10 dB from 24.1 GHz to 31.0 GHz (fractional bandwidth of 24.6%), which agrees well with the simulation results. The reflection coefficients are -33.1 dB by measurement and -25.7 dB by simulation, and the maximum gains are 6.2 dBi and 5.5 dBi at 28 GHz, respectively. These results demonstrate that the proposed antenna has high-gain characteristics being suitable for 5G wireless communications.