Selective extraction of fungicide carbendazim in fruits using ß-cyclodextrin based molecularly imprinted polymers.

Considering the importance of developing a new analytical approach for pesticide residue detection for the sake of ensuring food safety, a ß-cyclodextrin based molecularly imprinted polymer was prepared for selective determination of carbendazim. The polymers consist of a porous and hollow structure demonstrating the selective abundant adsorption sites for carbendazim molecule. The selectivity and adsorption capacity of the imprinted polymers were analyzed with dispersive solid-phase extraction and analyzed with high performance liquid chromatography coupled with ultraviolet. The results of imprinted polymers were higher than non-imprinted polymers with the maximum adsorption capacity of 3.65 mg/g within 30 min of total adsorption time. The reusability of the imprinted polymers was determined to evaluate its effectiveness and stability, which proved that the polymers lost 10% efficiency within seven consecutive recycles. The developed method displayed good linearity over the concentration range of 0.05-2.0 mg/L. The recovery percentage of 81.33-97.23 with relative standard deviations of 1.49-4.66% was obtained from spiked apple, banana, orange, and peach samples with a limit of detection of 0.03 mg/L and a limit of quantification of 0.10 mg/L (signal to noise ratio = 3/10). The overall performance of the proposed method evident that this technique provided a desirable outcome and it can be used as a convenient approach, as it qualifies the analytical standards.

Determination of Carbamates and Thiocarbamates in Water, Soil and Sediment of the Formoso River, TO, Brazil.

Considering the increase in agricultural production in Brazil, the use of pesticides for this production, and that there are no studies on pesticides in the region, the presence of carbamates and thiocarbamates was investigated in different environmental compartments of the Formoso River, TO, Brazil, by UHPLC/MS/MS. The collections were made on the banks of this river, in the area of influence of the agricultural project. The active principles were not found in the soil and sediment samples, only the propoxur principle was found in the water, reaching values of up to 0.025 µg L-1 . It was found that the biodiversity of the Tocantinense savannah is under threat, because even though only one of the substances surveyed, propoxur and its derivatives, has been detected, they are substances of high toxicity and tendency to contaminate surface and groundwater to varying degrees and irreversible damage to different species.

Targeting VEGFR2 protein by marine Streptomyces globosus VITLGK011-derived compound BECA: An in vitro and in silico analysis.

This study investigates the anticancer cytotoxic mechanism of action of benzoyloxy-ethyl-carbamic acid (BECA) produced by Streptomyces globosus VITLGK011. Flow cytometry analysis confirmed that BECA (at IC50 : 3.12 µg/ml) treatment for 24 h induced apoptosis in 60% of cells. Schrodinger Maestro tools such as QikProp and DFT were used to confirm that BECA is an eligible drug-like molecule, with suitable physiochemical properties. Glide XP tool was used to perform induced-fit docking between BECA and 30 cancer drug target proteins. The highest significance was observed for VEGFR2 protein (-6.7 kcal/mol). GROMACS tool was used to perform molecular dynamic simulation between BECA and VEGFR2 protein for 40 ns. Root mean square deviation, root mean square fluctuation, H-bond, and trajectory analysis, confirmed that BECA is a suitable inhibitor of VEGFR2 protein. Results conclude that BECA is a valid VEGFR2 inhibitor, and it thus exerts the observed anticancer cytotoxicity against MCF-7 cells.

Multi-column ultra-high performance liquid chromatography screening with chaotropic agents and computer-assisted separation modeling enables process development of new drug substances.

Modern process research and development can often be hampered by the tedious method development required to chromatographically resolve mixtures of chemical species with very similar physical properties. Herein, we describe a simple approach for the development and implementation of an efficient ultra-high performance liquid chromatography (UHPLC) assay that is extensively applied to the separation and analysis of multicomponent reaction mixtures of closely related pharmaceutical intermediates and impurities. Methods are optimized using multi-column and multi-solvent UHPLC screening in conjunction with chromatography simulation software (ACD Labs/LC Simulator). This approach is implemented to enable the separation, identification, mapping and control of impurities formed within the process chemistry optimization of the dimeric catalyst used in the synthesis of new drug substances. The final method utilized a sub-2 µm C18 stationary phase (2.1 mm I.D. × 50 mm length, 1.7 µm particle size ACQUITY UPLC BEH C18) with a non-conventional chaotropic mobile phase buffer (35 mM potassium hexafluorophosphate in 0.1% phosphoric acid/acetonitrile) in order to achieve baseline separation of all reaction components. The chromatographic simulation and modeling strategy served to generate 3D resolution maps with robust separation conditions that match the outcome of subsequent experimental data (overall ΔtR < 0.35%). Our multi-column UHPLC screening with computer-assisted chromatographic modeling is a great addition to the toolbox of synthetic chemists and can be a powerful tool for streamlining process chemistry optimization in organic chemistry laboratories across both academic and industrial sectors.

Determination of 107 Pesticide Residues in Wolfberry with Acetate-buffered Salt Extraction and Sin-QuEChERS Nano Column Purification Coupled with Ultra Performance Liquid Chromatography Tandem Mass Spectrometry.

A multi-residue method for the determination of 107 pesticide residues in wolfberry has been developed and validated. Similar pretreatment approaches were compared, and the linearity, matrix effect, analysis limits, precision, stability and accuracy were validated, which verifies the satisfactory performance of this new method. The LODs and LOQs were in the range of 0.14-1.91 µg/kg and 0.46-6.37 µg/kg, respectively. The recovery of analytes at three fortification levels (10 µg/kg, 50 µg/kg, 100 µg/kg) ranged from 63.3-123.0%, 72.0-118.6% and 67.0-118.3%, respectively, with relative standard deviations (RSDs) below 15.0%. The proposed method was applied to the analysis of fifty wolfberry samples collected from supermarkets, pharmacies and farmers' markets in different cities of Shandong Province. One hundred percent of the samples analyzed included at least one pesticide, and a total of 26 pesticide residues was detected in fifty samples, which mainly were insecticides and bactericide. Several pesticides with higher detection rates were 96% for acetamiprid, 82% for imidacloprid, 54% for thiophanate-methyl, 50% for blasticidin-S, 42% for carbendazim, 42% for tebuconazole and 36% for difenoconazole in wolfberry samples. This study proved the adaptability of the developed method to the detection of multiple pesticide residues in wolfberry and provided basis for the research on the risks to wolfberry health.

Sorption of carbendazim and linuron from aqueous solutions with activated carbon produced from spent coffee grounds: Equilibrium, kinetic and thermodynamic approach.

Spent coffee grounds (SCG) have been used for the production of activated carbon (AC) by impregnation with different ratios of phosphoric acid at 600 °C, Xp (H3PO4/coffee): 3:130%, 4:130%, 3:150% and 4:150%. The obtained AC was characterized by BET, FTIR and SEM. BET surface area corresponds to 803.422 m2 g-1. The influences of the main parameters such as contact time, the pesticides initial concentration, adsorbent dose, pH and temperature on the efficiency of separation process were investigated during the batch operational mode. Results were modeled by adsorption isotherms: Langmuir, Freundlich and Temkin isotherms, which gave satisfactory correlation coefficients. The maximum adsorption capacities calculated from the Langmuir isotherms were 11.918 mg g-1 for carbendazim and 5.834 mg g-1 for linuron at room temperature. Adsorption kinetics of carbendazim and linuron have been studied by the pseudo-first-order, the pseudo-second-order and the intraparticle diffusion model. The results of adsorption kinetics have been fitted the best by pseudo-second-order model. The resulted data from FTIR characterization pointed to the presence of many functional groups on the AC surface. SCG adsorbent, as an eco-friendly and low-cost material, showed high potential for the removal of carbendazim and linuron from aqueous solutions.

A hierarchically porous composite monolith polypyrrole/octadecyl silica/graphene oxide/chitosan cryogel sorbent for the extraction and pre-concentration of carbamate pesticides in fruit juices.

A hierarchically porous structured composite monolith sorbent of polypyrrole-coated graphene oxide and octadecyl silica incorporated in chitosan cryogel (PPY/GOx/C18/chitosan) was synthesized and used as solid-phase extraction sorbent for the determination of carbamate pesticides. Various factors affecting the characteristics of the adsorbents (chemistry of the sorbent, polymerization time, concentrations of graphene oxide and octadecyl silica) and the extraction efficiency using the prepared sorbents, such as sample loading, desorption conditions, sample volume, sample flow rate, sample pH, and ionic strength, were investigated and optimized. Under the optimal conditions of sorbent preparation and extraction, the developed composite monolith sorbent provided wide linear responses from 1.0 to 500 µg L-1 for carbofuran and diethofencarb, from 0.5 to 500 µg L-1 for carbaryl, and from 2.0 to 500 µg L-1 for isoprocarb. The limits of detection using HPLC-UV at 203, 220, and 208 nm were in the range of 0.5-2.0 µg L-1. When the composite monolith sorbent was applied for the pre-concentration and determination of carbamate in fruit juices, good recoveries (84.1-99.5%) were achieved. The developed sorbents were porous and exhibited low back pressure enabling their use at high flow rates during sample loading. Extraction and clean-up were highly efficient, and the good physical and chemical stability of the sorbent enables reuse up to 13 times. Graphical abstract ᅟ.

Characterization and application of a lanthanide-based metal-organic framework in the development and validation of a matrix solid-phase dispersion procedure for pesticide extraction on peppers (Capsicum annuum L.) with gas chromatography-mass spectrometry.

The metal-organic framework [(La0.9 Sm0.1 )2 (DPA)3 (H2 O)3 ]∞ was synthetized and characterized by X-ray diffractometry, differential thermogravimetric analysis, and infrared spectroscopy. The material was tested for the development and validation of a matrix solid-phase dispersion procedure for extraction of atrazine, bifenthrin, bromuconazole, clofentezine, fenbuconazole, flumetralin, procymidone, and pirimicarb, from peppers, with analysis using gas chromatography with mass spectrometry in the selected ion monitoring mode. The method developed was linear over the range tested (50.0-1000.0 µg/kg for procymidone and 200.0-1000.0 µg/kg for all other pesticides), with correlation coefficients ranging from 0.9930 to 0.9992. Experiments were carried out at 250.0, 500.0, and 1000.0 µg/kg fortification levels, and resulted in recoveries in the range of 52.7-135.0%, with coefficient of variation values between 5.2 and 5.4%, respectively, for [(La0.9 Sm0.1 )2 (DPA)3 (H2 O)3 ]∞ sorbent. Detection and quantification limits ranged from 16.0 to 67.0 µg/kg and from 50.0 to 200.0 µg/kg, respectively, for the different pesticides studied. The results were compared with literature data. The developed and validated method was applied to real samples. The analysis detected the presence of residues of pesticides procymidone, fenbuconazole, flumetralin, clofentezine, atrazine, and bifenthrin.

Synthesis and application of selective adsorbent for pirimicarb pesticides in aqueous media using allyl-ß-cyclodextrin based binary functional monomers.

BACKGROUND: Binary functional monomers, allyl-ß-cyclodextrin (allyl-ß-CD) and methacrylic acid (MAA) or allyl-ß-CD and acrylonitrile (AN), were exploited in a fabrication of molecularly imprinted polymers (MIPs) for selective recognition and large enrichment of pirimicarb from aqueous media. RESULTS: Special attention was paid to the computational simulation of the imprinting molecular and functional monomers. The morphological characteristics of MIPs made of allyl-ß-CD and MAA (M-MAA) were characterised by scanning electron microscopy. The effect of binding capacity of MAA-linked allyl-ß-CD MIPs (M-MAA) demonstrated higher efficiency than that of AN-linked allyl-ß-CD MIPs (M-AN) when tested in binding specificity. Finally, M-MAA was chosen to run through molecularly imprinted solid-phase extraction (MISPE) to analyse the spiked fresh leafy vegetables of pirimicarb. CONCLUSION: The present proposed technique is a promising tool for the preparation of the receptors which could recognise pirimicarb pesticide in aqueous media. © 2017 Society of Chemical Industry.

Mollecarbamates, Molleureas, and Molledihydroisoquinolone, o-Carboxyphenethylamide Metabolites of the Ascidian Didemnum molle Collected in Madagascar.

The extract of a sample of the tunicate Didemnum molle (MAY13-117) collected in Mayotte afforded eight new metabolites, mollecarbamates A-D (1-4) and molleureas B-E (5-8), along with the two known natural products, N,N'-diphenylethyl urea (10) and molleurea A (11). Another sample of D. molle (MAD11-BA065) collected in Baie des Assassins, Madagascar, afforded molledihydroisoquinolone (9). Mollecarbamates 1-4 are a family of compounds that possess repeating o-carboxyphenethylamide units and a carbamate moiety, while the molleureas 5-8 contain tetra- and penta-repeating carboxyphenethylamide units and a urea bridge in different positions. Molledihydroisoquinolone (9) is a cyclic form of o-carboxyphenethylamide. We propose that these unique natural products are most probably produced by an unprecedented biosynthetic pathway that contains a yet unknown chorismate mutase variant. The structures of the compounds were elucidated by interpretation of the data from 1D and 2D NMR, HRESIMS, and MS/MS analyses of the positive ESIMS experiments. Compounds 1-8 were tested against pathogenic bacteria and in a cytoprotective HIV cell based assay but did not show any significant effects in these assays.

Preparation of a magnetic porous carbon with hierarchical structures from waste biomass for the extraction of some carbamates.

In this study, corn stalk was used to synthesize a magnetic adsorbent by pyrolysis together with KHCO3 as the chemical activator and iron(III) salt as the magnetic reagent. The characterization by scanning electron microscopy, transmission electron microscopy and N2 adsorption-desorption analysis showed that the magnetic carbon adsorbent had a structure of hierarchical pores with a high specific surface area. To evaluate its adsorption performance, the adsorbent was used for the extraction of carbamates pesticides (propoxur, isoprocarb and fenobucarb) from water and zucchini samples before high-performance liquid chromatography analysis. The result showed that the adsorbent had a good adsorption capability for the analytes. Under the optimized conditions, a good linearity for the analytes existed in the range of 0.1-100.0 ng/mL for water samples and 0.5-100.0 ng/g for zucchini samples with the correlation coefficients of 0.9992-0.9998. The limits of detection for the analytes at a signal to noise ratio of 3 were 0.03 ng/mL for water samples and 0.20-0.50 ng/g for zucchini samples.

Sulfonated poly(styrene-divinylbenzene) modified with amines and the application for pipette-tip solid-phase extraction of carbendazim in apples.

Sulfonated poly(styrene-divinylbenzene) modified with five kinds of amine functional groups was applied to the determination of carbendazim in apple samples with a pipette-tip solid-phase extraction method. The structures of the polymers were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, and thermogravimetric analysis. Five different modifications of the solid-phase extraction sorbent based on sulfonated poly(styrene-divinylbenzene) were tested under static and pipette-tip solid-phase extraction conditions. The polymer modified with p-methoxyaniline showed the best recognition capacity and adsorption amount for carbendazim. Under the optimum conditions, 3.00 mg of the adsorbent, 1.00 mL of ethyl acetate as washing solvent, and 1.00 mL of ammonia/acetonitrile (5:95, v/v) as elution solvent were used in the pretreatment procedure of apple samples. The calibration graphs of carbendazim in methanol were linear over 5.00-200.00 µg/mL, and the limits of detection and quantification were 0.01 and 0.03 µg/mL, respectively. The method recoveries of carbendazim were in the range of 91.31-98.13% with associated intraday relative standard deviations of 0.76-2.13% and interday relative standard deviations of 1.10-1.85%. Sulfonated poly(styrene-divinylbenzene) modified with p-methoxyaniline showed satisfactory results (recovery: 97.96%) and potential for the rapid purification of carbendazim in apple samples combined with the pipette-tip solid-phase extraction.

Graphene-based pipette tip solid-phase extraction with ultra-high performance liquid chromatography and tandem mass spectrometry for the analysis of carbamate pesticide residues in fruit juice.

Graphene-based pipette tip solid-phase extraction was combined with ultra-high performance liquid chromatography and tandem mass spectrometry for the determination of carbamate pesticide residues in fruit juice samples. Four milligrams of graphene was used as sorbent material to pack a 1000 µL pipette tip for the extraction of pirimicarb, propoxur, isoprocarb, fenobucarb, and diethofencarb from 3 mL of fruit juice sample. The whole extraction process was finished in 12 min, and the volume of eluent used was only 1.5 mL. Under the optimized conditions, good linear relationship (R > 0.999) and lower limits of detection (0.0022-0.033 ng/mL) were achieved. The recoveries at three spiked levels ranged from 80.90 to 124.60% with relative standard deviations less than 4.88%. Compared with commercially available sorbents including propylsulfonic acid silica, graphitized carbon black, and C18 , graphene was superior in extraction efficiency. The proposed method is simple, rapid, sensitive, selective, and solvent saving.

A molecularly imprinted organic-inorganic hybrid monolithic column for the selective extraction and HPLC determination of isoprocarb residues in rice.

An IPC-imprinted (IPC is isoprocarb) poly(methacrylic acid)/SiO2 hybrid monolithic column was prepared and applied for the recognition of the template. The hybrid monolithic column was synthesized in a micropipette tip using methyltrimethoxysilane as the inorganic precursor, 3-(methacryloxy)propyltrimethoxysilane as the coupling agent, and ethylene glycol dimethacrylate as the cross-linker. The synthesis conditions, including the porogenic solvent, coupling agent, volume ratio of the inorganic alcoholysate and organic part, were optimized. The prepared monolithic column was characterized by SEM and FTIR spectroscopy. A simple, rapid, and sensitive method for the determination of IPC in rice using the imprinted monolithic column microextraction combined with HPLC was developed. Several parameters affecting the sample pretreatment were investigated, including the eluent, washing solution, and loading sample volume. The linearity of the calibration curve was observed in the range of 9.0-1000 µg/kg for IPC in rice with the correlation coefficient (r2) of 0.9983. The LOD was 3.0 µg/kg (S/N = 3). The assay gave recovery values ranging from 91 to 107%. The proposed method has been successfully applied for the selective extraction and sensitive determination of IPC in rice and a satisfactory result was obtained.

Halogen bonding and pharmaceutical cocrystals: the case of a widely used preservative.

3-Iodo-2-propynyl-N-butylcarbamate (IPBC) is an iodinated antimicrobial product used globally as a preservative, fungicide, and algaecide. IPBC is difficult to obtain in pure form as well as to handle in industrial products because it tends to be sticky and clumpy. Here, we describe the preparation of four pharmaceutical cocrystals involving IPBC. The obtained cocrystals have been characterized by X-ray diffraction, solution and solid-state NMR, IR, and DSC analyses. In all the described cases the halogen bond (XB) is the key interaction responsible for the self-assembly of the pharmaceutical cocrystals thanks to the involvement of the 1-iodoalkyne moiety of IPBC, which functions as a very reliable XB-donor, with both neutral and anionic XB-acceptors. Most of the obtained cocrystals have improved properties with respect to the source API, in terms, e.g., of thermal stability. The cocrystal involving the GRAS excipient CaCl2 has superior powder flow characteristics compared to the pure IPBC, representing a promising solution to the handling issues related to the manufacturing of products containing IPBC.

Santacruzamate A, a potent and selective histone deacetylase inhibitor from the Panamanian marine cyanobacterium cf. Symploca sp.

A dark brown tuft-forming cyanobacterium, morphologically resembling the genus Symploca, was collected during an expedition to the Coiba National Park, a UNESCO World Heritage Site on the Pacific coast of Panama. Phylogenetic analysis of its 16S rRNA gene sequence indicated that it is 4.5% divergent from the type strain for Symploca and thus is likely a new genus. Fractionation of the crude extract led to the isolation of a new cytotoxin, designated santacruzamate A (1), which has several structural features in common with suberoylanilide hydroxamic acid [(2), SAHA, trade name Vorinostat], a clinically approved histone deacetylase (HDAC) inhibitor used to treat refractory cutaneous T-cell lymphoma. Recognition of the structural similarly of 1 and SAHA led to the characterization of santacruzamate A as a picomolar level selective inhibitor of HDAC2, a Class I HDAC, with relatively little inhibition of HDAC4 or HDAC6, both Class II HDACs. As a result, chemical syntheses of santacruzamate A as well as a structurally intriguing hybrid molecule, which blends aspects of both agents (1 and 2), were achieved and evaluated for their HDAC activity and specificity.

Graphene grafted silica-coated Fe3O4 nanocomposite as absorbent for enrichment of carbamates from cucumbers and pears prior to HPLC.

In this paper, a novel graphene (G) grafted silica-coated Fe3O4 nanocomposite was fabricated by the chemical bonding of G onto the surface of silica-coated Fe3 O4 nanoparticles. Some carbamates (metolcarb, carbaryl, pirimicarb, and diethofencarb) in cucumber and pear samples were enriched by this nanocomposite prior to their determination by HPLC with UV detection. Experimental parameters that may affect the extraction efficiency were investigated. Under the optimum conditions, a linear response was achieved in the concentration range of 0.5-100.0 ng/g for metolcarb, carbaryl, and diethofencarb, and 1.0-100 ng/g for pirimicarb with the correlation coefficients (r) ranging from 0.9956 to 0.9984. The LOD (S/N = 3) of the method were found to be in the range from 0.08 to 0.2 ng/g. The RSDs were in the range from 2.4 to 5.8%. The results indicated that the G grafted silica-coated Fe3 O4 nanocomposite was stable and efficient for magnetic SPE and has a great application potential for the preconcentration of other organic pollutants from real samples.

Microwave accelerated selective Soxhlet extraction for the determination of organophosphorus and carbamate pesticides in ginseng with gas chromatography/mass spectrometry.

Microwave accelerated selective Soxhlet extraction (MA-SSE), a novel selective extraction technique, was investigated in this study. A Soxhlet extraction system containing a glass filter was designed as an extractor. During the procedure of MA-SSE, both the target analytes and the interfering components were extracted from the sample into the extraction solvent enhanced by microwave irradiation. After the solvent flowed though the sorbent, the interfering components were adsorbed by the sorbent, and the target analytes remaining in the solvent were collected in the extraction bottle. No cleanup or filtration was required after extraction. The efficiency of the MA-SSE approach was demonstrated in the determination of organophosphorus and carbamate pesticide residues in ginseng by gas chromatography/mass spectrometry (GC/MS). Under the optimized conditions, low limits of detection (0.050-0.50 µg/kg) were obtained. The recoveries were in the range of 72.0-110.1% with relative standard deviations less than 7.1%. Because of the effect of microwave irradiation, MA-SSE showed significant advantage compared with other extraction techniques. The sorbent used in this study showed good cleanup ability. The mechanism of MA-SSE was demonstrated to be based on the rupture of the cell walls according to the structural changes of ginseng samples. On the basis of the results, MA-SSE as a simple and effective sample preparation technique for the analysis of pesticide residues in complex matrixes shows great promise.

Dispersive liquid-liquid microextraction of pesticides and metabolites from soils using 1,3-dipentylimidazolium hexafluorophosphate ionic liquid as an alternative extraction solvent.

In this work, the use of the ionic liquid (IL) 1,3-dipentylimidazolium hexafluorophosphate ([PPIm][PF6]) as an alternative extractant for IL dispersive liquid-liquid microextraction (IL-DLLME) of a group of pesticides and metabolites (2-aminobenzimidazole, carbendazim/benomyl, thiabendazole, fuberidazole, carbaryl, 1-naphthol, and triazophos) from soils is described. After performing an initial ultrasound-assisted extraction (USE), the IL-DLLME procedure was applied for the extraction of these organic analytes from soil extracts. Separation and quantification was achieved by high-performance liquid chromatography (HPLC) with fluorescence detection (FD). Calibration, precision, and accuracy of the described USE-IL-DLLME-HPLC-FD method using [PPIm][PF6] as an alternative extractant was evaluated with two soils of different physicochemical properties. Accuracy percentages were in the range 93-118% with RSD values below 20%. A comparison of the performance of [PPIm][PF6] versus that of the so-common 1-hexyl-3-methylimidazolium hexafluorophosphate ([HMIm][PF6]) was accomplished. Results indicate a comparable extraction efficiency with both ILs, being slightly higher with [HMIm][PF6] for the metabolite 2-aminobenzimidazole, and slightly higher with [PPIm][PF6] for triazophos. In all cases, LODs were in the low ng/g range (0.02-14.2 ng/g for [HMIm][PF6] and 0.02-60.5 ng/g for [PPIm][PF6]). As a result, the current work constitutes a starting point for the use of the IL [PPIm][PF6] for further analytical approaches.

Development of an improved single-drop microextraction method and its application for the analysis of carbamate and organophosphorus pesticides in water samples.

An improved single-drop microextraction (SDME) method combined with high performance liquid chromatography has been developed for the detection of trace carbamate and organophosphorus pesticides in water samples. The most fascinating feature of the proposed method is the use of an oval-shaped polychloroprene rubber (PCR) tube to load the extraction solvent, which efficiently loads more solvent and improves the stability of extraction microdrop. Furthermore, this device provides a larger contact surface between the extraction solvent and the inner surface of the oval-shaped PCR tube than that between the extraction solvent and the tip of a microsyringe needle in the conventional SDME. It thereby avoids the problem of the drop floating upwards or dislodging from the tip of the microsyringe needle as observed in the traditional SDME. This method is significant for the great improvement it can offer in extraction efficiency. A series of extraction parameters were investigated systematically using carbamate and organophosphorus as the model analytes. Under the optimal conditions, the enrichment factors for analysis were between 117 and 177, and the limits of detection were ≦0.63 µg L(-1) (S/N = 3). The repeatability study was carried out by extracting the spiked water samples. Here the relative standard deviations varied between 4.0 and 5.8% (n = 5). Additionally, the proposed method was successfully applied to the determination of pesticides in real water samples, and good recoveries were obtained from 79% to 112%. The proposed method was demonstrated to hold advantages of low cost, simplicity of operation, and successful application to in real water samples.