Analytical research on the separation and residue of chiral pesticide triadimenol in fruit and vegetable puree.

In this paper, a method for the separation of triadimenol stereoisomers using ultra-performance convergence chromatography and an analytical method for the determination of triadimenol stereoisomer residues in pumpkin puree, apple puree, and tomato puree as a supplement for infants are established. Test samples were extracted with acetonitrile and successively purified with graphitized carbon black and Florisil column. Afterward, Acquity Trefoil AMY1 column was adopted for chiral separation of chromatographic column, and gradient elute was carried out with supercritical carbon dioxide-methanol as the mobile phase and with external standard method for quantitation. Results showed that the linearly dependent coefficient of the four kinds of triadimenol stereoisomers within 1.0 and 50 mg/L was greater than 0.9997, and the limit of quantitation of the four kinds of triadimenol stereoisomers was 0.05 mg/kg. Recovery experiment was carried out within 0.05 and 1.0 mg/kg scope, the recoveries were 81.0-107％, and the relative standard deviation was 2.3-7.6%. This method implemented the separation of triadimenol stereoisomers and its residue test in pumpkin puree, apple puree, and tomato puree as a supplement for infants, and it can provide reliable technical support for the analysis of pesticide residue and assessment of product quality.

Enantioseparation and determination of triazole fungicides in fruit juice by aqueous biphasic system coupled with HPLC-MS/MS.

The aqueous biphasic system based on choline ionic liquids and ethylene/propylene oxide copolymer coupled with high-performance liquid chromatography-tandem mass spectrometry was developed for the simultaneous determination of the enantiomers of two fungicides: myclobutanil and tebuconazole. The influence of mass fractions of ionic liquids and the copolymer on the extraction efficiency of the target fungicides was investigated. The analytes are mainly concentrated in the bottom, copolymer-rich phase. The extraction efficiencies of the selected fungicides were significantly affected by the concentrations of the copolymer, and their extraction efficiencies decreased with the higher mass fractions of the copolymer, while the mass fraction of ionic liquids had little effect on their extraction behavior. Excellent extraction efficiency was achieved using the aqueous biphasic system based on choline L-lysinate and the copolymer. At three spiked concentrations of 0.01, 0.05, and 0.1 mg/kg, the average recoveries of the selected fungicides ranged from 80 to 89%, with the relative standard deviations in the range of 2.1-5.3%. Limits of quantitation for the enantiomers of tebuconazole and myclobutanil were 0.5 and 5.0 µg/kg, respectively. The developed system could be successfully applied to the analysis of triazole fungicides residue in real samples.

Magnetic metal-organic framework MIL-100 (Fe)/polyethyleneimine composite as an adsorbent for the magnetic solid-phase extraction of fungicides and their determination using HPLC-UV.

Fe3O4@MIL-100 (Fe)/PEI are used for the first time as an adsorbent material for the extraction of pesticide residues (epoxiconazole, flusilazole, tebuconazole, and triadimefon) from food matrices. The adsorbent proposed (Fe3O4@MIL-100(Fe)/PEI) was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), thermogravimetric (TG) analysis, and vibrating sample magnetometer (VSM) techniques to evaluate the properties of the sorbent. Then, the Fe3O4@MIL-100 (Fe)/PEI was employed for the quantification of the four triazole fungicides in fruits and vegetables (apple, orange, tomato, cabbage, and cucumber) using HPLC-UV for separation and detection. During the extraction process, the main parameters such as amount of adsorbent, extraction time, pH value, ionic strength, eluting solvent, and eluting volume were optimized. Under the optimum conditions, good linearity of this method was observed for all analytes, with correlation coefficients (R2) ≥ 0.9908. The limits of detection (LODs) ranged from 0.021-3.04 µg kg-1. The extraction recoveries of the four triazole fungicides varied from 73.9 to 109.4% with relative standard deviations (RSD) in the range 0.5 to 6.2%. Compared with other MOFs, the modification of Fe3O4@MIL-100 (Fe) with PEI shows high efficient adsorption due to the combined benefits of MIL-100 (Fe) and PEI. The material is easily synthesized, has good stability, and is of low cost.  Graphical abstract.

Cellulose-Based Hectocycle Nanopolymers: Synthesis, Molecular Docking and Adsorption of Difenoconazole from Aqueous Medium.

The goal of this work was to develop polymer-based heterocycle for water purification from toxic pesticides such as difenoconazole. The polymer chosen for this purpose was cellulose nanocrystalline (CNC); two cellulose based heterocycles were prepared by crosslinking with 2,6-pyridine dicarbonyl dichloride (Cell-X), and derivatizing with 2-furan carbonyl chloride (Cell-D). The synthesized cellulose-based heterocycles were characterized by SEM, proton NMR, TGA and FT-IR spectroscopy. To optimize adsorption conditions, the effect of various variable such as time, adsorbent dose, pH, temperature, and difenoconazole initial concentration were evaluated. Results showed that, the maximum difenoconazole removal percentage was about 94.7%, and 96.6% for Cell-X and Cell-D, respectively. Kinetic and thermodynamic studies on the adsorption process showed that the adsorption of difenoconazole by the two polymers is a pseudo-second order and follows the Langmuir isotherm model. The obtained values of ∆G ° and ∆H suggest that the adsorption process is spontaneous at room temperature. The results showed that Cell-X could be a promising adsorbent on a commercial scale for difenoconazole. The several adsorption sites present in Cell-X in addition to the semi crown ether structure explains the high efficiency it has for difenoconazole, and could be used for other toxic pesticides. Monte Carlo (MC) and Molecular Dynamic (MD) simulation were performed on a model of Cell-X and difenoconazole, and the results showed strong interaction.

Magnetic amino-functionalized hollow silica-titania microsphere as an efficient sorbent for extraction of pesticides in green and roasted coffee beans.

This study describes the synthesis and application of a magnetic amino-functionalized hollow silica-titania microsphere as a new sorbent for magnetic dispersive micro-solid phase extraction of selected pesticides in coffee bean samples. The sorbent was fully characterized by Fourier-transform infrared spectroscopy, field emission scanning electron microscopy, transition electron microscopy, energy-dispersive X-ray spectroscopy, and vibrating sample magnetometry techniques. Significant extraction parameters affecting the proposed method, such as extraction time, sorbent amount, sample solution pH, salt amount, and desorption conditions (desorption solvent and time) were investigated and optimized. All the figures of merits were validated in coffee bean samples under the matrix-matched calibration method. Linear dynamic ranges were 5-250 µg/kg with the determination coefficients (R2 ) > 0.9980. The limits of detection for the pesticides of chlorpyrifos, malathion, hexaconazole, and atrazine were 1.42, 1.43, 1.35, and 1.33 µg/kg, respectively. Finally, the method was successfully applied for the determination of the pesticides in green and roasted coffee bean samples, and the obtained recoveries were in the range of 74-113% for spiked samples. The prepared sorbent could be used for the magnetic dispersive micro-solid phase extraction of pesticides in the plant-derived food matrix.

The synergistic effect and microscopic mechanism of co-adsorption of three emerging contaminants and copper ion on gemini surfactant modified montmorillonite.

Montmorillonite (G-Mt) modified by a gemini quaternary ammonium cationic surfactant (Propyl bis (hexadecyl dimethyl ammonium) chloride, 16-3-16) was used to remove emerging contaminants (ECs) (such as 1H-Benzotriazole (BTA), 5-Methyl-1H-benzotriazole (TTA) and 1-Hydroxybenzotriazole (HOBT)) and Cu2+ from wastewater. Based on the adsorption of the above three ECs in our previous studies, single adsorption of Cu2+ and the simultaneous adsorption of three ECs with Cu2+ on G-Mt were also investigated. G-Mt showed much lower adsorption amount on Cu2+ comparing with original montmorillonite (Ca-Mt) in single adsorption system due to the difficulty of ion-exchange property of G-Mt. In co-adsorption system, three organic pollutants and Cu2+ played a synergistic effect and the adsorption capacity of G-Mt on them increased, the influence sequence of Cu2+ on the adsorption of three ECs or the effect of ECs on the adsorption of Cu2+ both followed as: TTA > BTA > HOBT. The results of FT-IR, EDS and XPS revealed that the complex of Cu2+ and ECs were adsorbed onto G-Mt via forming complexes and hydrophobic interaction in co-adsorption system. The pH experiment showed that the optimum pH of the co-adsorption of ECs and Cu2+ on G-Mt was 5. Molecular dynamics (MD) simulations showed that three ECs or ECs combining with Cu2+ were dominantly adsorbed in the interlayer space of G-Mt, which resulted in the arrangement manner of 16-3-16 between the layer of G-Mt before and after adsorption of three organic pollutants was different. Furthermore, by quantitatively analyzing electrostatic potential (ESP) distribution, average local ionization energy (ALIE) distribution and their minimum points on three ECs molecules surfaces, Multiwfn program has been applied to probe the microscopic mechanism. The synergistic effect of co-adsorption will promote enrichment of copper ions and ECs to remove them more efficiently in polluted waters.

Determination of 107 Pesticide Residues in Wolfberry with Acetate-buffered Salt Extraction and Sin-QuEChERS Nano Column Purification Coupled with Ultra Performance Liquid Chromatography Tandem Mass Spectrometry.

A multi-residue method for the determination of 107 pesticide residues in wolfberry has been developed and validated. Similar pretreatment approaches were compared, and the linearity, matrix effect, analysis limits, precision, stability and accuracy were validated, which verifies the satisfactory performance of this new method. The LODs and LOQs were in the range of 0.14-1.91 µg/kg and 0.46-6.37 µg/kg, respectively. The recovery of analytes at three fortification levels (10 µg/kg, 50 µg/kg, 100 µg/kg) ranged from 63.3-123.0%, 72.0-118.6% and 67.0-118.3%, respectively, with relative standard deviations (RSDs) below 15.0%. The proposed method was applied to the analysis of fifty wolfberry samples collected from supermarkets, pharmacies and farmers' markets in different cities of Shandong Province. One hundred percent of the samples analyzed included at least one pesticide, and a total of 26 pesticide residues was detected in fifty samples, which mainly were insecticides and bactericide. Several pesticides with higher detection rates were 96% for acetamiprid, 82% for imidacloprid, 54% for thiophanate-methyl, 50% for blasticidin-S, 42% for carbendazim, 42% for tebuconazole and 36% for difenoconazole in wolfberry samples. This study proved the adaptability of the developed method to the detection of multiple pesticide residues in wolfberry and provided basis for the research on the risks to wolfberry health.

Advanced Continuous Flow Platform for On-Demand Pharmaceutical Manufacturing.

As a demonstration of an alternative to the challenges faced with batch pharmaceutical manufacturing including the large production footprint and lengthy time-scale, we previously reported a refrigerator-sized continuous flow system for the on-demand production of essential medicines. Building on this technology, herein we report a second-generation, reconfigurable and 25 % smaller (by volume) continuous flow pharmaceutical manufacturing platform featuring advances in reaction and purification equipment. Consisting of two compact [0.7 (L)×0.5 (D)×1.3 m (H)] stand-alone units for synthesis and purification/formulation processes, the capabilities of this automated system are demonstrated with the synthesis of nicardipine hydrochloride and the production of concentrated liquid doses of ciprofloxacin hydrochloride, neostigmine methylsulfate and rufinamide that meet US Pharmacopeia standards.

Characterization and application of a lanthanide-based metal-organic framework in the development and validation of a matrix solid-phase dispersion procedure for pesticide extraction on peppers (Capsicum annuum L.) with gas chromatography-mass spectrometry.

The metal-organic framework [(La0.9 Sm0.1 )2 (DPA)3 (H2 O)3 ]∞ was synthetized and characterized by X-ray diffractometry, differential thermogravimetric analysis, and infrared spectroscopy. The material was tested for the development and validation of a matrix solid-phase dispersion procedure for extraction of atrazine, bifenthrin, bromuconazole, clofentezine, fenbuconazole, flumetralin, procymidone, and pirimicarb, from peppers, with analysis using gas chromatography with mass spectrometry in the selected ion monitoring mode. The method developed was linear over the range tested (50.0-1000.0 µg/kg for procymidone and 200.0-1000.0 µg/kg for all other pesticides), with correlation coefficients ranging from 0.9930 to 0.9992. Experiments were carried out at 250.0, 500.0, and 1000.0 µg/kg fortification levels, and resulted in recoveries in the range of 52.7-135.0%, with coefficient of variation values between 5.2 and 5.4%, respectively, for [(La0.9 Sm0.1 )2 (DPA)3 (H2 O)3 ]∞ sorbent. Detection and quantification limits ranged from 16.0 to 67.0 µg/kg and from 50.0 to 200.0 µg/kg, respectively, for the different pesticides studied. The results were compared with literature data. The developed and validated method was applied to real samples. The analysis detected the presence of residues of pesticides procymidone, fenbuconazole, flumetralin, clofentezine, atrazine, and bifenthrin.

Optimization and validation of RP-HPLC method for simultaneous estimation of palbociclib and letrozole.

A simple, rapid, and robust RP-HPLC method have been developed and validated to measure palbociclib (PB) and letrozole (LT) at single wavelength (254 nm). A isocratic elution of samples performed on Intersil C8 (4.6 mm × 250 mm particle size 5 µm) column with mobile phase consisting 0.02 M sodium dihydrogen phosphate buffer (pH 5.5): acetonitrile: methanol (80:10:10 v/v/v) delivered at flow rate 1.0 mL min-1. A good linear response was achieved over the range of 5-50 µg mL-1. The LODs for PB and LT were found to be 0.098 and 0.0821 µg mL-1, while the LOQs for PB and LT were 0.381-0.315 µg mL-1, respectively. The method was quantitatively evaluated in terms of system suitability test, linearity, precision, accuracy (recovery) and robustness as per standard guidelines. The method is simple, convenient and suitable for the analysis of PB and LT in bulk drug.

Quinoliniumolate and 2H-1,2,3-Triazole Derivatives from the Stems of Paramignya trimera and Their α-Glucosidase Inhibitory Activities: In Vitro and in Silico Studies.

From a CHCl3-soluble extract of the stems of Paramignya trimera, two new alkaloids, (E)-2-(prop-1-enyl)-N-methylquinolinium-4-olate (1) and (R)-2-ethylhexyl 2H-1,2,3-triazole-4-carboxylate (2), were isolated. Their structures were elucidated based on the spectroscopic data interpretation. Compound 2 possesses α-glucosidase inhibitory activity, with an IC50 value of 137.9 µM. Molecular docking studies of 1 and 2 with human maltase-glucoamylase (MGAM) were performed for the first time; thus, the 2,3-diH+-1H-1,2,3-triazolium cation (2i) showed good interactions with both MGAM-N (2QMJ) and -C (3TOP) terminal subunits.

Magnetic iron oxide nanoparticles grafted N-isopropylacrylamide/chitosan copolymer for the extraction and determination of letrozole in human biological samples.

Magnetic iron oxide nanoparticles are used for the extraction of a drug from an aqueous solution. In the current study, the magnetic iron oxide nanoparticles were synthesized via a facile coprecipitation approach, and then modified by (3-mercaptopropyl)trimethoxysilane followed by grafting thermosensitive polymer N-isopropylacrylamide and biopolymer chitosan. Structure, morphology, size, thermal resistance, specific surface area, and magnetic properties of the grafted nanosorbent were characterized by using Fourier transform infrared spectroscopy, field emission scanning electron microscopy, transmission electron microscopy, elemental analysis, thermogravimetric analysis, specific surface area analysis and vibrating sample magnetometry. The effective parameters on sorption/desorption of letrozole on grafted magnetic nanosorbent were evaluated. The best sorption of letrozole via the grafted nanosorbent occurred at 20°C at an optimum pH of 7. The extraction of trace letrozole in human biological fluids is investigated and revealed 89.1 and 97.8% recovery in plasma and urine, respectively.

Synthesis, structural studies, and cytotoxic evaluation of novel ursolic acid hybrids with capabilities to arrest breast cancer cells in mitosis.

Some novel chemically modified frameworks of ursolic acid have been designed and synthesized. The key step was the cycloaddition of azidopropyl-3ß-hydroxy-urs-12-en-28-oate with the appropriate C28 propargyl esters of ursolic, corosolic, asiatic, oleanolic, and betulinic acid under Click reaction conditions, and the products were obtained in 74-84% yields. In view of their intriguing structural diversity, they have been subjected to detailed 1D and 2D NMR studies and their structures are thoroughly assigned. The synthesized compounds were screened for their anticancer potential against two human breast cancer cell lines (MCF-7 & MDA-MB-231) using sulforhodamine B cell proliferation assay. The GI50 data revealed that the synthesized compounds exhibit highly potent activities against the two tested cell lines. Interestingly, the synthesized compounds showed selectivity and higher activity against MDA-MB-231 cell line than MCF-7. Among the tested compounds, compound 17 is the most potent one with GI50 value of 1.4 ± 0.1 µM and showed 2.9 times more activity than the standard doxorubicin against MDA-MB-231. In addition, 17 arrests cells in mitotic phase of cell cycle, resulting in a change in cell phenotype. In view of the selective and highly promising activity against breast cancer cell lines, these compounds can serve as promising leads for further development.

Pesticide residue removal in classic domestic processing of tomato and its effects on product quality.

This study was undertaken to evaluate the effectiveness of several household practices (washing with water or acidic, alkaline, and oxidizing solutions, and peeling) in minimizing pesticide residue contamination of tomatoes, as well as the impact on the quality of the treated fruit. Tests were performed using two systemic fungicides (azoxystrobin and difenoconazole) and one contact fungicide (chlorothalonil). Solid-liquid extraction with low temperature partition (SLE/LTP) and liquid-liquid extraction with low temperature partition (LLE/LTP) were used to prepare the samples for pesticides determination by gas chromatography. Washing the tomatoes with water removed approximately 44% of chlorothalonil, 26% of difenoconazole, and 17% of azoxystrobin. Sodium bicarbonate (5%) and acetic acid (5%) solutions were more efficient, removing between 32 and 83% of the residues, while peeling removed from 68 to 88% of the pesticides. The washing solutions altered some fruit quality parameters, including acidity and chroma, and also caused weight loss. Acetic acid (0.15 and 5%) and hypochlorite (1%) solutions had the greatest effect on these parameters.

Tablet-effervescence-assisted dissolved carbon flotation for the extraction of four triazole fungicides in water by gas chromatography with mass spectrometry.

A pretreatment method named tablet-effervescence-assisted dissolved carbon flotation was introduced for the determination of four triazole fungicides in environmental water. In this method, the use of effervescent tablet composed of nontoxic sodium carbonate and sodium dihydrogen phosphate could generate CO2 in situ to assist the dispersion of extraction solvent and to accelerate mass transfer of target analytes. In addition, the simple phase separation simply based on the rising of low-density organic solvent from the aqueous phase was applied rather than the application of apparatus, which demonstrated the potential for on-site extraction in the field. The experimental variables, including the composition of effervescent tablets, amount of effervescent tablets, types and volume of extraction solvent, were investigated. Under the optimized conditions, the method showed good linearity for myclobutanil, tebuconazole, epoxiconazole, and difenoconazole in the range of 1-100 µg/L. The limits of detection and the limits of quantification were within the range of 0.15-0.26 and 0.49-0.86 µg/L, respectively. The obtained correlation coefficients varied from 0.997 to 0.999, and suitable enrichment factors were 422-589. The recoveries were 82.5-112.9% with relative standard deviations of 4.7-13.5%.

Polyethylene glycol grafted flower-like cupric nano oxide for the hollow-fiber solid-phase microextraction of hexaconazole, penconazole, and diniconazole in vegetable samples.

A simple, rapid, highly efficient, and reliable sample preparation method has been developed for the extraction and analysis of triazole pesticides from cucumber, lettuce, bell pepper, cabbage, and tomato samples. This new sorbent in the hollow-fiber solid-phase microextraction method is based on the synthesis of polyethylene glycol-polyethylene glycol grafted flower-like cupric oxide nanoparticles using sol-gel technology. Afterward, the analytes were analyzed by high-performance liquid chromatography with ultraviolet detection. The main parameters that affect microextraction efficiency were evaluated and optimized. This method has afforded good linearity ranges (0.5-50 000 ng/mL for hexaconazol, 0.012-50 000 ng/mL for penconazol, and 0.02-50 000 ng/mL for diniconazol), adequate precision (2.9-6.17%, n = 3), batch-to-batch reproducibility (4.33-8.12%), and low instrumental LODs between 0.003 and 0.097 ng/mL (n = 8). Recoveries and enrichment factors were 85.46-97.47 and 751-1312%, respectively.

Dispersive liquid-liquid microextraction based on solidification of floating organic droplet for the determination of triazine and triazoles in mineral water samples.

A simple, rapid, and sensitive method for the determination of atrazine, simazine, cyproconazole, tebuconazole, and epoxiconazole in mineral water employing the dispersive liquid-liquid microextraction with solidification of a floating organic drop with determination by liquid chromatography tandem mass spectrometry has been developed. A mixed solution of 250 µL 1-dodecanol and 1250 µL methanol was injected rapidly into 10 mL aqueous solution (pH 7.0) with 2% w/v NaCl. After centrifugation for 5 min at 2000 rpm, the organic solvent droplets floated on the surface of the aqueous solution and the floating solvent solidified. The method limits of detection were between 3.75 and 37.5 ng/L and limits of quantification were between 12.5 and 125 ng/L. The recoveries ranged from 70 to 118% for repeatability and between 76 and 95% for intermediate precision with a relative standard deviation from 2 to 18% for all compounds. Low matrix effect was observed. The proposed method can be successfully applied in routine analysis for determination of pesticide residues in mineral water samples, allowing for monitoring of triazine and triazoles at levels below the regulatory limits set by international and national legislations.

Fabric phase sorptive extraction followed by UHPLC-MS/MS for the analysis of benzotriazole UV stabilizers in sewage samples.

A fast and sensitive sample preparation strategy using fabric phase sorptive extraction followed by ultra-high-performance liquid chromatography and tandem mass spectrometry detection has been developed to analyse benzotriazole UV stabilizer compounds in aqueous samples. Benzotriazole UV stabilizer compounds are a group of compounds added to sunscreens and other personal care products which may present detrimental effects to aquatic ecosystems. Fabric phase sorptive extraction is a novel solvent minimized sample preparation approach that integrates the advantages of sol-gel derived hybrid inorganic-organic nanocomposite sorbents and the flexible, permeable and hydrophobic surface chemistry of polyester fabric. It is a highly sensitive, fast, efficient and inexpensive device that can be reused and does not suffer from coating damage, unlike SPME fibres or stir bars. In this paper, we optimized the extraction of seven benzotriazole UV filters evaluating the majority of the parameters involved in the extraction process, such as sorbent chemistry selection, extraction time, back-extraction solvent, back-extraction time and the impact of ionic strength. Under the optimized conditions, fabric phase sorptive extraction allows enrichment factors of 10 times with detection limits ranging from 6.01 to 60.7 ng L(-1) and intra- and inter-day % RSDs lower than 11 and 30 % for all compounds, respectively. The optimized sample preparation technique followed by ultra-high-performance liquid chromatography and tandem mass spectrometry detection was applied to determine the target analytes in sewage samples from wastewater treatment plants with different purification processes of Gran Canaria Island (Spain). Two UV stabilizer compounds were measured in ranges 17.0-60.5 ng mL(-1) (UV 328) and 69.3-99.2 ng mL(-1) (UV 360) in the three sewage water samples analysed.

Simultaneous determination of tebuconazole, trifloxystrobin, and its metabolite trifloxystrobin acid residues in gherkin under field conditions.

A rapid, simple, and selective analytical method for the simultaneous determination of tebuconazole, trifloxystrobin, and its metabolite trifloxystrobin acid residues in gherkin and soil was developed and validated by gas chromatography coupled with mass spectrometry. The samples were extracted with acetonitrile and cleaned up by dispersive solid-phase extraction with primary secondary amine sorbent. The limit of quantification of the method was 0.05 mg/kg for all three compounds. The method was validated using blank samples spiked at three levels and recoveries ranged from 83.5 to 103.8% with a relative standard deviation of 1.2 to 4.8%. The developed method was validated and applied for the analysis of a degradation study sample. The residues of trifloxystrobin and tebuconazole were found to dissipate following first-order kinetics with half-life ranging between 3.31-3.38 and 3.0-3.04 days, respectively, for two different dosages. Pesticide residues were below the European Union maximum residue level after seven days for trifloxystrobin (0.2 mg/kg) and ten days for tebuconazole (0.05 mg/kg), which suggested the use of this fungicide mixture to be safe to humans. These results can be utilized in formulating the spray schedule and safety evaluation on trifloxystrobin and tebuconazole in gherkin crop.

Enantioseparation of new triadimenol antifungal active compounds by electrokinetic chromatography and molecular modeling study of chiral recognition mechanisms.

Chiral separation of 12 new triadimenol antifungal active compounds by electrokinetic chromatography and chiral recognition mechanisms by computer-aided molecular modeling techniques were studied. Seven neutral cyclodextrins were used as chiral selectors. Heptakis-(2,3,6-tri-O-methyl)-ß-cyclodextrin (TM-ß-CD) exhibited a very high enantioselectivity power to 12 active compounds compared to the other tested CDs. The influences of the concentration of TM-ß-CD, buffer pH, buffer concentration, applied voltage, and temperature were investigated, respectively. Under the optimum separation conditions, all the 12 active compounds were baseline separated and the resolutions of most compounds were beyond 2.50. The study of the analyte structure-enantioseparation relationships showed that substitutions in the side chains played important roles on enantiomeric separation. By means of computer-aided molecular modeling software Discovery Studio 2.5/Sybyl 7.0/Gold 3.0.1, inclusion process between TM-ß-CD and these enantiomers was investigated and their binding energies were calculated. The results suggested that the enantioseparation result related to the difference in binding energy. And the good separation obtained in the presence of the TM-ß-CD chiral selector was due to the big binding energy difference of two enantiomers with the chiral selector.