Evaluation of Er,Cr:YSGG laser irradiation for debonding of zirconia hybrid abutment crowns from titanium bases.

To evaluate the efficacy of Er,Cr:YSGG laser irradiation on the removal of zirconia hybrid abutment crowns (HAC) from ti-bases and investigate the effects of laser output power and zirconia generation on debonding time and fracture resistance of crowns. A hundred monolithic zirconia HACs were fabricated by using 4Y-TZP and 5Y-TZP materials and subsequently cemented onto the ti-bases with a resin luting agent. Each zirconia group was further divided into 5 subgroups according to the debonding procedure as control (no debonding), 4.5 W-, 5 W-, and 6 W-laser irradiation, heat processed (n = 10). Er,Cr:YSGG laser (Waterlase MD; Biolase Technology Inc., Irvine, CA) was used on a noncontact hard tissue mode at a 20-Hz repetition rate and 140-µs pulse duration with 50% water and 50% air. Debonding durations were recorded for each specimen, and modes of failure were investigated. Crowns were re-cemented on their corresponding ti-bases, and HACs were subjected to fracture strength test. Debonding duration and fracture strength data were statistically analyzed. Fractured zirconia crown surfaces of ti-bases were examined under the scanning electron microscope. 5Y-TZP crowns were debonded from ti-bases in significantly lower durations in comparison with 4Y-TZP crowns for all output powers [4.5 W (P = 0.001), 5 W (P = 0.002), and 6 W (P = 0.0014)]. For both 4Y-TZP and 5Y-TZP materials, debonding duration was significantly decreased with the increase in laser output power (P ≤ 0.001 for 4Y- and 5Y-TZP). In comparison with 4Y-TZP heat-processed group to the 4Y-TZP laser-irradiated groups, no significant differences were detected in terms of fracture strength (P > 0.05), while heat-processed crowns exhibited significantly lower fracture strength values than those of control group (P = 0.006). All debonding procedures significantly reduced fracture strength values of 5Y-TZP crowns in comparison with the control group (P ≤ 0.001). The common failure type was the adhesive failure between the zirconia crown and resin cement for all groups. SEM evaluation showed no visible damage caused by laser irradiation or heat application. The use of Er,Cr:YSGG laser irradiation is an efficient way to retrieve zirconia crowns from ti-bases. The higher the output power of the laser, the shorter the bonding procedure. The debonding duration and fracture strength of the crown were affected by the zirconia generation. Debonded 5Y-TZP zirconia crowns should not be reused due to the decrease in mechanical strength values.

A Turn-On Luminescence Method for Phosphate Determination Based on Fast Green-Functionalized ZrO2:Yb,Er@ZrO2 Core@Shell Upconversion Nanoparticles.

The development of practical and sensitive tools for detecting phosphate deficiency could facilitate engineering approaches to enhance crop yield and quality in phosphate-stressed environments, reducing the misuse of nonrenewable fertilizers and their consequent ecological impact. Herein, a 975 nm-activated method based on ZrO2:Yb,Er@ZrO2 core@shell upconversion nanoparticles is presented for rapid visualization and determination of the phosphate ions in aqueous solutions and extracts. At optimized thickness, the nondoped ZrO2 shell not only enhances the emission of the ZrO2:Yb,Er but also provides an active surface for the intense interaction with the phosphate group, allowing a "label-free" determination that avoids the use of additional phosphate-recognizing elements like ligands or antibodies. According to the experimental evidence, the optical output of the ZrO2:Yb,Er@ZrO2 nanoparticles specifically matches with the absorption spectrum of the fast green alimentary dye (FG) electrostatically attached to the nanoparticle surface, activating the Förster resonance energy transfer (FRET) and thereby the upconversion luminescence quenching. Upon addition of the phosphate ions and the covalent interaction with the ZrO2:Yb,Er@ZrO2-FG nanocomplex, the FG is gradually removed, displaying a fast and reproducible "turn-on" luminescence which allows measurements in a few minutes. This rapid response is due to the stronger coordination between the ZrO2 shell and the phosphate compared to the FG molecules (-31.97 and -5.99 eV, respectively). The detection method was then effectively modulated in a 20-1000 nM linear response range without interfering effects of commonly coexisting ions, achieving a detection limit up to 15 times lower than that obtained with the conventionally used colorimetric methods.

Nd:YAG Laser Treatment of Bioglass-coated Zirconia Surface and Its Effect on Bond Strength and Phase Transformation.

PURPOSE: To evaluate the morphological properties, phase transformation, and microshear bond strength of composite cement to bioglass-coated zirconia surfaces treated with Nd:YAG laser. MATERIALS AND METHODS: Seventy-five zirconia disks were divided into five groups (n = 15). Group C received no surface treatment (control). Group S was subjected to sandblasting with 50-µm aluminum oxide particles. Group B samples were coated with bioglass 45S5. Groups BL9 and BL5 received bioglass coating and laser irradiation with 9 J/cm2 and 5 J/cm2 energy density. Morphological assessment was done using atomic force microscopy (AFM) and scanning electron microscopy (SEM). Zirconia phase transformation was assessed by XRD. Microhear bond strength testing was performed using a modified microtensile tester. The data were analyzed using the Welch test and the Games-Howell test (p < 0.05). RESULTS: The sandblasted and bioglass-coated groups showed the highest bond strengths compared to other groups (p < 0.05). Group S showed the highest surface roughness and the highest frequency of cohesive failure. In all samples, the tetragonal phase decreased after surface treatment. Groups BL9 and BL5 showed some levels of tetragonal to cubic phase transformation. CONCLUSION: Bioglass coating of zirconia surfaces (using the slurry method) can increase its microshear bond strength comparable to that of sandblasting. Surface roughness of sandblasted zirconia was the highest among all methods. Irradiation of Nd:YAG laser on bioglass-coated zirconia surfaces is not effective and decreases its bond strength compared to sandblasting and bioglass coating. Increasing the Nd:YAG laser energy density cannot increase the surface roughness of bioglass-coated zirconia surfaces. Bioglass coating results in transformation of the tetragonal to the cubic phase.

Surface Characterization and Cell Adhesion of Different Zirconia Treatments: An in vitro Study.

AIM: The aim of this study was to characterize the surface of zirconia subjected to different treatments and evaluate its effect on cell adhesion and proliferation. MATERIALS AND METHODS: A total of 80 zirconia disks were divided into four groups (n = 20) according to the surface treatments used: group I: as-sintered (AS), no surface treatment applied; group II: abrasion treatment applied using Rocatec (ROC; 3M ESPE) system with silica-coated alumina powder of grit size 110 µm; group III: erbium, chromium:yttrium, scandium, gallium, garnet (Er, Cr:YSGG) laser (LAS; BIOLASE) was used at a frequency of 20 Hz and output power of 3 W; and group IV: specimens were subjected to the selective infiltration etching (SIE) technique. Surface characterization was evaluated for the different groups (roughness, hardness, and morphology), and cell behavior (adhesion and proliferation) was tested (a = 0.05). RESULTS: The ROC group reported a significant increase in surface roughness (2.201 ± 0.352) and Vickers hardness (1758 ± 16.6) compared with the other surface treatments. The SIE surface-treated group reported a significantly higher number of cells (64.5 ± 2.6 and 53.5 ± 2.2 respectively) compared with the other surface-treated groups. CONCLUSION: The SIE is a promising surface treatment for zirconia that significantly enhances cell adhesion and osseointegration. CLINICAL SIGNIFICANCE: The SIE treatment of zirconia implants may help in a faster and better osseointegration.

Shear bond, wettability and AFM evaluations on CO2 laser-irradiated CAD/CAM ceramic surfaces.

The purpose of this study is to determine the CO2 laser irradiation in comparison with sandblasting (Sb), hydrofluoric acid (Hf) and silane coupling agent (Si) on shear bond strength (SBS), roughness (Rg) and wettability (Wt) of resin cement to CAD/CAM ceramics. Sixty (CAD/CAM) ceramic discs were prepared and distributed into six different groups: group A, control lithium disilicate (Li); group B, control zirconia (Zr); group C, Li: CO2/HF/Si; group D, Li: HF/Si; group E, Zr: CO2/Sb/Si; group F, Zr: Sb/Si. Result showed significant difference between irradiated and non-irradiated in terms of shear bond strength for zirconia ceramics (p value = 0.014). Moreover, partial surface wettability for irradiated and non-irradiated ceramics. Irradiated surface demonstrated more rough surface in lithium disilicate than zirconia ceramics. CO2 irradiation could increase shear bond strength, surface roughness and wettability for both CAD/CAM ceramics.

Influence of cyclic loading on the adhesive effectiveness of resin-zirconia interface after femtosecond laser irradiation and conventional surface treatments.

BACKGROUND AND OBJECTIVE: The aim of this study was to evaluate the influence of cyclic loading on the shear bond strength (SBS) of a self-adhesive resin cement to zirconia surfaces after femtosecond laser irradiation at different steps and several conventional surface treatments. MATERIALS AND METHODS: One hundred fifty square-shaped zirconia samples were divided into five groups according their surface treatment: NT Group-no surface treatment; APA25 Group-airborne abrasion with 25 µm alumina particles; TSC Group-tribochemical silica coating; FS20 Group-femtosecond laser irradiation (800 nm, 4 mJ, 40 fs/pulse, 1 kHz, step 20); and FS40 Group-femtosecond laser irradiation (same parameters except step 40). Self-adhesive resin cement cylinders were bonded at the centre of the zirconia surface. For each experimental group, half of the specimens were subject to cyclic loading under 90 N (50.000 cycles, 3 cycles/sec) and the rest of the specimens were stored in distilled water at 37°C. All subgroups were tested for SBS with a universal testing machine at a crosshead speed of 0.5 mm/min, until fracture. The results were analyzed statistically. RESULTS: When cyclic loading was applied, all surface treatments had lower SBS values, except APA25. The four surface treatments had the same SBS values when cyclic loading was employed. CONCLUSIONS: Use of femtosecond laser irradiation could be an alternative to conventional surface treatments to achieve suitable adhesion zirconia and resin cements. Femtosecond laser irradiation at step 40 is preferable because it is more efficient and faster.

Effect of femtosecond laser beam angle on bond strength of zirconia-resin cement.

Yttrium-stabilized tetragonal zirconia polycrystalline (Y-TZP) ceramic is widely used as an all-ceramic core material because of its enhanced mechanical and aesthetic properties. The bond strength of Y-TZP restorations affects long-term success; hence, surface treatment is required on ceramic boundaries. This study evaluated the effect of different laser beam angles on Y-TZP-resin cement shear bond strength (SBS). Forty plates of Y-TZP ceramics were randomly assigned to four groups (n = 10). A femtosecond amplifier laser pulse was applied on Y-TZP surface with different incidence angles (90°, 75°, 60°, 45°). The resin cement was adhered onto the zirconia surfaces. The SBS of each sample was measured using universal testing machine at crosshead speed of 1 mm/min. The SBS was analyzed through one-way analysis of variance (ANOVA)/Tukey tests. The results showed that the degree of laser beam angle affects the SBS of resin cement to Y-TZP. The laser beam was applied to a surface with a 45° angle which resulted in significantly higher SBS (18.2 ± 1.43 MPa) than other groups (at 90° angulation (10.79 ± 1.8 MPa), at 75° (13.48 ± 1.2 MPa) and at 60° (15.85 ± 0.81 MPa); p < 0.001). This study shows that decreasing of the angle between the ceramic surface and the laser beam increased the SBS between the resin cement and the ceramic material, as well as the orifice.

Surface alterations of zirconia and titanium substrates after Er,Cr:YSGG irradiation.

This study investigated changes in the roughness parameters (Sa in µm(2) and Ra in µm) of yttrium-stabilized tetragonal zirconia polycrystal (Y-TZP) and large-grit sandblasted acid-etched (SLA) titanium (TI) materials after decontamination by erbium chromium-doped:yttrium, scandium, gallium, and garnet (Er,Cr:YSGG) laser irradiation. Twenty disks were analyzed in this study: 10 disks of Y-TZP (5 mm in diameter and 3 mm in height), standardized with CAD-CAM procedures, and 10 disks of SLA TI (5 mm in diameter and 4 mm in thickness). Disks were randomized into four groups (n = 5), according to whether laser irradiation was performed: Y-TZP_G1 and TI_G1 were not treated by laser (control groups), whereas Y-TZP_G2 and TI_G2 were irradiated with Er,Cr:YSGG laser (1.5 W/20 Hz, air-water cooling proportion of 80%/25%). The surface topography of the disks was analyzed by confocal light microscopy. The mean Sa and Ra values were calculated from five profiles from each group. The results were statistically analyzed by t-test at the 95% confidence level (α = 0.05). For Y-TZP, the Sa results (in mean ± SD) for Y-TZP_G1 and Y-TZP_G2 were 2.60 ± 1.1 and 0.80 ± 0.17 µm(2), respectively, and the Ra results were 2.01 ± 0.71 and 0.18 ± 0.15 µm, respectively (both p < .05). For SLA TI, the Sa results for TI_G1 and TI_G2 were 1.99 ± 0.5 and 3.37 ± 0.75 µm(2), respectively, and the Ra results were 1.78 ± 0.53 and 3.84 ± 0.63 µm, respectively (both p < .05). Er,Cr:YSGG laser irradiation alters the surface roughness of zirconia and SLA TI.

Quantification of the amount of blue light passing through monolithic zirconia with respect to thickness and polymerization conditions.

STATEMENT OF PROBLEM: Dual-polymerized luting composite resin cements would benefit from enhanced irradiance transmitted through a ceramic restoration. A quantification of the amount of transmitted light through translucent zirconia is lacking. PURPOSE: The purpose of this study was to evaluate the amount of light (360 to 540 nm) passing through translucent and conventional zirconia and a glass ceramic with respect to material thickness and different polymerizing modes. MATERIAL AND METHODS: Six translucent and a conventional zirconia (negative control) and a glass ceramic (positive control) were considered. Ten specimens of each material and thickness (.5, 1, 1.5, 2, 2.5, 3 mm) were fabricated (n=480). Zirconia materials were sintered according to manufacturers' instructions. The irradiance passing the different ceramics and thicknesses was measured with a violet-blue LED polymerizing unit in 3 polymerizing modes (plasma, high, and standard power mode) with a USB4000 Spectrometer. The polymerizing unit was placed directly on the specimen's surface. Data were analyzed with one and multivariate analysis and the Pearson correlation analysis (α=.05). RESULTS: In all materials, the translucency and its rate decreased exponentially according to the specimen thickness. The highest influence on the measured irradiance passing through translucent zirconia was exerted by ceramic thickness (P<.05, partial eta squared [ηP²]=.998), closely followed by polymerizing mode (ηP²=.973), while the effect of the material (P=.03, ηP²=.06) and mean grain size (P=.029, ηP²=.027) was significant but low. CONCLUSIONS: Zirconia was less translucent than the glass ceramic, but the translucency decreased more slowly with material thickness, thus approaching the translucency of glass ceramics at a specimen thicknesses of 2.5 to 3 mm.

Influence of hydrophilic pre-treatment on resin bonding to zirconia ceramics.

Atmospheric plasma or ultraviolet (UV) treatment alters the surface characteristics of tetragonal zirconia polycrystal (TZP), increasing its hydrophilicity by reducing the contact angle against water to zero. This suggests that such treatment would increase the wettability of bonding resin. The purpose of this study was to determine how increasing the hydrophilicity of TZP through plasma irradiation, UV treatment, or application of ceramic primer affected initial bonding with resin composites. Here, the effect of each pre-treatment on the hydrophilicity of TZP surfaces was determined by evaluating change in shear bond strength. Plasma irradiation, UV, or ceramic primer pre-treatment showed no significant effect on bonding strength between TZP surfaces and resin composites. In addition, alumina blasting yielded no significant increase in bond strength. Plasma irradiation, UV treatment, or ceramic primer pre-treatment did not lead to significant increase in bond strength between TZP and resin composites.

Bond strength and monomer conversion of indirect composite resin restorations, Part 1: Light vs heat polymerization.

PURPOSE: To assess the resin microtensile bond strength (MTBS) and the monomer conversion (MC) of indirect composite resin restorations made of three different materials. MATERIALS AND METHODS: Two light-polymerized direct materials (Filtek Z100 and Premise) and one light- and heat-polymerized indirect material (Premise Indirect) were used. For MTBS testing, 42 cylindrical samples were fabricated (7 pairs per material). Surface conditioning included airborne-particle abrasion, cleaning, and application of a silane. Cylinders were bonded to each other using adhesive resin (Optibond FL). Specimens were stored in water for 24 h. Another 15 cylinders (5 per material) were fabricated for MC measurements (FT-IR) immediately and at 24 h. The MTBS data were submitted to one-way ANOVA and the MC to two-way ANOVA (material and storage time) (α=0.05), followed by post-hoc comparisons with the Tukey test. RESULTS: The MTBS to Z100 was 72.2 MPa, significantly higher than that to Premise (48.4 MPa) and Premise Indirect (52.7 MPa). The immediate MC was similar for all materials (range 51% to 56%) and significantly increased at 24 h (range 57% to 66%), except for Z100. Premise Indirect showed the highest MC (66% at 24 h). CONCLUSION: Z100 showed better "bondability" than Premise and Premise Indirect. Premise Indirect, with its heat initiator, did not present a higher MC.

Effect of Er,Cr:YSGG laser treatment on microshear bond strength of zirconia to resin cement before and after sintering.

PURPOSE: To evaluate the effect of Er,Cr:YSGG laser treatment on microshear bond strength of zirconia to resin cement before and after sintering. MATERIALS AND METHODS: Ninety pre-sintered yttrium-stabilized tetragonal zirconia specimens (4 × 3 × 2 mm) were divided into 6 groups (n = 15). In group C, sintered zirconia was not treated (control group). In groups AS2 and AS3, sintered zirconia blocks were irradiated by Er,Cr:YSGG using a power of 2 and 3 W, respectively. Groups PS2 and PS3 consisted of pre-sintered blocks conditioned by Er,Cr:YSGG at 2 and 3 W, respectively. In group AA, sintered zirconia was air abraded with 50-µm alumina powder. One block was made using the same preparations as mentioned above and was morphologically assessed by SEM. Microcylinders of Panavia F 2.0 were placed on the treated surface of the groups. Samples were incubated at 37°C and 98% humidity for 48 h and then subjected to microshear bond strength testing. The mode of failure was evaluated. Data were analyzed by one-way ANOVA and Tukey's HSD test (p < 0.05). RESULTS: There was a statistically significant difference between group AA and the others (p < 0.0001). A significant difference was also noted between groups AS3 and C (p = 0.031). Complete surface roughness was seen in group AA and the bond failure was mostly cohesive, while in laser-treated groups, the surfaces roughness was much lower vs other groups, and the mode of failure was mostly adhesive. CONCLUSION: Laser treatment of pre-sintered Y-TZP cannot be recommended for improving the bond. Although sandblasting of sintered Y-TZP yielded better results than the rest of the groups, 3 W power after sintering can also be effective in enhancing the bonding strength of resin cement to zirconia.

Evaluation of experimental coating to improve the zirconia-veneering ceramic bond strength.

PURPOSE: To evaluate the shear bond strength (SBS) between zirconia and veneering ceramic following different surface treatments of zirconia. The efficacy of an experimental zirconia coating to improve the bond strength was also evaluated. MATERIALS AND METHODS: Zirconia strips were fabricated and were divided into four groups as per their surface treatment: polished (control), airborne-particle abrasion, laser irradiation, and application of the experimental coating. The surface roughness and the residual monoclinic content were evaluated before and after the respective surface treatments. A scanning electron microscope (SEM) analysis of the experimental surfaces was performed. All specimens were subjected to shear force in a universal testing machine. The SBS values were analyzed with one-way ANOVA followed by Bonferroni post hoc for groupwise comparisons. The fractured specimens were examined to observe the failure mode. RESULTS: The SBS (29.17 MPa) and roughness values (0.80) of the experimental coating group were the highest among the groups. The residual monoclinic content was minimal (0.32) when compared to the remaining test groups. SEM analysis revealed a homogenous surface well adhered to an undamaged zirconia base. The other test groups showed destruction of the zirconia surface. The analysis of failure following bond strength testing showed entirely cohesive failures in the veneering ceramic in all study groups. CONCLUSION: The experimental zirconia surface coating is a simple technique to increase the microroughness of the zirconia surface, and thereby improve the SBS to the veneering ceramic. It results in the least monoclinic content and produces no structural damage to the zirconia substructure.

Preparation of graphene-ZrO2 nanocomposites by heat treatment and photocatalytic degradation of organic dyes.

ZrO2 nanoparticles were synthesized by combining a solution containing zinconyl chloride in distilled water with a NH4OH solution under microwave irradiation. Graphene and ZrO2 nanocomposites were synthesized in an electric furnace at 700 degrees C for 2 hours. The heated graphene-ZrO2 nanocomposites were characterized by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. In addition, UV-vis spectrophotometry was used to evaluate the heated graphene-ZrO2 nanocomposites as a catalyst in the photocatalytic degradation of organic dyes. The photocatalytic effect of the heated graphene-ZrO2 nanocomposites was compared with that of unheated graphene nanoparticles, heated graphene nanoparticles, and unheated graphene-ZrO2 nanocomposites in organic dyes (methylene blue, methyl orange, and rhodamine B) under ultraviolet light at 254 nm.

Perovskite phase formation of monosized lead zirconate (PbZrO3) nanoparticles prepared by the sono-assisted co-precipitation method.

The chemical reaction and phase evolution of perovskite lead zirconate (PbZrO3; PZ) nanoparticles, synthesized by the sono-assisted co-precipitation method, have been investigated. The nanopowders were characterized using the X-ray diffraction technique (XRD), Fourier transform infrared (FT-IR) spectroscopy, Raman spectroscopy, transmission electron microscope (TEM) and differential scanning calorimetry (DSC). The perovskite phase, PbZrO3, begins to form at 600 degrees C and was completed at 900 degrees C. During the reaction of PbZrO3, only the tetragonal zirconia (t-ZrO2) phase was formed as an intermediate phase with low temperature range. Only Raman spectroscopy can identify the intermediate tetragonal zirconia (t-ZrO2) phase in PbZrO3 powders during calcinations process. The change in amount of the t-ZrO2 phase in PbZrO3 powders was estimated from Raman spectra as a function of the calcination temperature. Observations by transmission electron microscopy revealed that the PbZrO3 powders have a uniform spherical shape with nanosized particles. The average size of the particles is about 10.60 +/- 2 nm with narrow size distribution.

Fracture toughness of yttria-stabilized zirconia sintered in conventional and microwave ovens.

STATEMENT OF PROBLEM: The fabrication of zirconium dioxide (ZrO2) dental prosthetic substructures requires an extended sintering process (8 to 10 hours) in a conventional oven. Microwave sintering is a shorter process (2 hours) than conventional sintering. PURPOSE: The purpose of this study was to compare the fracture toughness of 3 mol % Y2O3-stabilized ZrO2 sintered in a conventional or microwave oven. MATERIAL AND METHODS: Partially sintered ZrO2 specimens from 3 manufacturers, KaVo, Lava 3M, and Crystal HS were milled (KaVo Everest engine) and randomly divided into 2 groups: conventional sintering and microwave sintering (n=16 per group). The specimens were sintered according to the manufacturers' recommendations and stored in artificial saliva for 10 days. Fracture toughness was determined by using a 4-point bend test, and load to fracture was recorded. Mean fracture toughness for each material was calculated. A 2-way ANOVA followed by the Tukey HDS post hoc test was used to assess the significance of sintering and material effects on fracture toughness, including an interaction between the 2 factors (α=.05). RESULTS: The 2-way ANOVA suggested a significant main effect for ZrO2 manufacturer (P<.001). The post hoc Tukey HSD test indicated that mean fracture toughness for the KaVo ZrO2 (5.85 MPa·m(1/2) ±1.29) was significantly higher than for Lava 3M (5.19 MPa·m(1/2) ±0.47) and Crystal HS (4.94 MPa·m(1/2) ±0.66) (P<.05) and no significant difference was observed between Lava 3M and Crystal HS (P>.05). The main effect of the sintering process (Conventional [5.30 MPa·m(1/2) ±1.00] or Microwave [5.36 MPa·m(1/2) ±0.92]) was not significant (P=.76), and there was no interaction between sintering and ZrO2 manufacturer (P=.91). CONCLUSIONS: Based on the results of this study, no statistically significant difference was observed in the fracture toughness of ZrO2 sintered in microwave or conventional ovens.

Analysis of the microstructure and mechanical performance of composite resins after accelerated artificial aging.

AIM: Researches that assess the behavior of dental materials are important for scientific and industrial development especially when they are tested under conditions that simulate the oral environment, so this work analyzed the compressive strength and microstructure of three composite resins subjected to accelerated artificial aging (AAA). METHODS: Three composites resins of 3M (P90, P60 and Z100) were analyzed and were obtained 16 specimens for each type (N.=48). Half of each type were subjected to UV-C system AAA and then were analyzed the surfaces of three aged specimens and three not aged of each type through the scanning electron microscope (SEM). After, eight specimens of each resin, aged and not aged, were subjected to compression test. RESULTS: After statistical analysis of compressive strength values, it was found that there was difference between groups (α <0.05). The resin specimens aged P60 presented lower values of compressive strength statistically significant when compared to the not subject to the AAA. For the other composite resins, there was no difference, regardless of aging, a fact confirmed by SEM. CONCLUSION: The results showed that the AAA influenced the compressive strength of the resin aged P60; confirmed by surface analysis by SEM, which showed greater structural disarrangement on surface material.

Densification kinetics of nanocrystalline zirconia powder using microwave and spark plasma sintering--a comparative study.

Two-stage densification process of nanosized 3 mol% yttria-stabilized zirconia (3Y-SZ) polycrystalline compacts during consolidation via microwave and spark-plasma sintering have been observed. The values of activation energies obtained for microwave and spark-plasma sintering 260-275 kJ x mol(-1) are quite similar to that of conventional sintering of zirconia, suggesting that densification during initial stage is controlled by the grain-boundary diffusion mechanism. The sintering behavior during microwave sintering was significantly affected by preliminary pressing conditions, as the surface diffusion mechanism (230 kJ x mol(-1)) is active in case of cold-isostatic pressing procedure was applied.

Effect of Er:YAG laser application on the shear bond strength and microleakage between resin cements and Y-TZP ceramics.

The objective of this study was to investigate the effect of Er:YAG laser irradiation on shear bond strength and microleakage between resin cements and yttrium-stabilized tetragonal zirconia (Y-TZP) ceramics. Eighty disc specimens of Y-TZP ceramics (6 mm × 4 mm) were prepared. The specimens were divided into two groups according to surface treatment (control and Er:YAG laser-treated). The control and lased specimens were separated into two groups for shear bond strength test (n = 20), and microleakage evaluation (n = 10). Specimens were subjected to shear bond strength test by a universal testing machine with a crosshead speed of 1 mm/min. Specimens for microleakage evaluation were then sealed with nail varnish, stained with 0.5% basic fuchsin for 24 h, sectioned, and evaluated under a stereomicroscope. The data were analyzed with one-way ANOVA and post hoc Tukey-Kramer multiple comparisons tests (α = 0.05) for shear bond strengths and a two related-samples tests (α = 0.05) for microleakage scores. Higher bond strength values were found in the laser-treated groups compared to the control groups. Microleakage scores among the groups showed that the laser-treated specimens had lower microleakage scores than those of control specimens in the adhesive-ceramic interface. Roughening surface of Y-TZP ceramic by Er:YAG laser increased the shear bond strengths of ceramic to dentin and reduced the microleakage scores.

Effect of light activation on resin-modified glass ionomer shear bond strength.

OBJECTIVE: Recent studies confirmed that resin-modified glass ionomers (RMGIs) set on the basis of two competing mechanisms, an acid-base reaction and a light-activated resin polymerization. This study evaluated the effect of the setting mechanism on bond strength by measuring the shear bond strength of three RMGIs to dentin with and without light activation. METHODS: Sixty human molars were ground to midcoronal dentin and randomly divided into six even groups: 1) Ketac Nano (KN), 2) KN without light cure (woLC), 3) Fuji Filling LC (FF), 4) FF woLC, 5) Fuji II LC (FII), and 6) FII woLC. The dentin surfaces of the specimens were conditioned/primed according to the manufacturers' instructions. A 1.54-mm diameter plastic tube was filled with RMGI material and affixed to the dentin surface. Groups 1, 3, and 5 were light cured for 20 seconds, and groups 2, 4, and 6 were immediately placed in a damp dark box with no light curing at 37°C for 24 hours. Shear bond strength testing was performed in an Instron device at 1 mm/min. Data were analyzed with a one-way analysis of variance (ANOVA) and Tukey/Kramer test (α=0.05). RESULTS: Mean ± standard deviation shear bond strength values (MPa) are: 7.1 ± 4.2 (KN), 11.7 ± 3.9 (FF), 10.2 ± 3.2 (FF woLC), 12.5 ± 5.1 (FII), and 0.3 ± 0.4 (FII woLC). Two KN, all KN woLC, and seven FII woLC specimens debonded before testing. Tukey/Kramer analysis revealed no significant differences in bond strength between the three light-cured RMGIs. KN and FII showed significantly lower bond strength without light cure, but no significant difference was observed between FF and FF woLC. CONCLUSIONS: The results of this study strongly suggest that light activation is necessary to obtain optimal bond strength between RMGI and dentin. FF may contain components that chemically activate resin polymerization. Clinically, KN and FII need to be light cured after placement of these RMGIs.