Highly stabilized fiber Bragg grating accelerometer based on cross-type diaphragm.

A fiber Bragg grating (FBG) accelerometer based on cross-type diaphragm was proposed and designed, in which the cross-beam acts as a spring element. To balance the sensitivity and stability, the accelerometer structure was optimized. The experimental results show that the designed device has a resonant frequency of 556 Hz with a considerable wide frequency bandwidth of up to 200 Hz, which is consistent with the simulation. The sensitivity of the device is 12.35 pm/g@100 Hz with a linear correlation coefficient of 0.99936. The proposed FBG accelerometer has simple structure and strong anti-interference capability with a maximal cross-error less than 3.26%, which can be used for mechanical structural health monitoring.

Tilted Bragg grating in a glycerol-infiltrated specialty optical fiber for temperature and strain measurements.

In this Letter, we propose an in-line tilted fiber Bragg grating sensor for temperature and strain measurements. The grating is inscribed in a specialty optical fiber using tightly focused femtosecond laser pulses and the line-by-line direct writing method. Beside the central core in which the grating is produced, a hollow channel filled with glycerol aqueous solution significantly improves the sensitivity of the fiber cladding modes due to its high thermo-optic coefficient. We show that the temperature sensitivity of the core mode is 9.8 pm/°C, while the one of the cladding modes is strongly altered and can reach -24.3 pm/°C, in the investigated range of 20-40°C. For the strain measurement, sensitivities of the core mode and the cladding modes are similar (∼0.60 pm/µÎµ) between 0 and 2400 µÎµ. The significative difference of temperature sensitivity between the two modes facilitates the discrimination of the dual parameters in simultaneous measurements.

Gold-coated tilted fiber Bragg gratings for lead ion sensing.

Surface plasmon resonance sensor based on gold-coated tilted fiber Bragg gratings (SPR-TFBGs) are perfectly suited for fine refractometry. Thanks to the functionalization of the gold layer, they can be used for label-free biosensing. They have been largely used for the specific detection of proteins and cells. In this work, we experimentally demonstrate that they are enough sensitive to detect a very small entity like an environmental pollutant. In this context, we report here a bio-functionalization of the SPR-TFBG with thrombin aptamers for lead ion detection. We used aqueous solutions of lead ions with increasing concentrations from 0.001 ppb to 10 ppb. Based on the affinity bending of Pb2+ ions to the thrombin aptamer, we experimentally demonstrated low detection level of lead ion concentration (0.001 ppb) while the saturation limit is meanly fixed by the physical dimension of the sensor and the binding efficiency.

Femtosecond pulse laser-engineered glass flexible structures instrumented with an in-built Bragg grating sensor.

The advent of near-infrared femtosecond pulse laser has enabled the highly-resolved manufacturing of micro/nano structures in various materials including glass. In this paper, we make use of an automated femtosecond laser system, so-called Femtoprint, to design a monolithic self-instrumented mechanism that we use for in-built strain sensing. To that aim, a flexible structure is designed and produced from a silica planar substrate. It has a flexural joint in which an optical waveguide and a Bragg grating have been directly inscribed using femtosecond pulse laser. The latter provides a non-destructive and non-intrusive measurement tool. The axial strain sensitivity of the in-built Bragg grating has been experimentally determined to be 1.22 pm/µ ϵ, while its temperature sensitivity is 10.51 pm/°C. The demonstration of such instrumented glass flexible mechanisms paves the way towards a new class of highly integrated sensors suitable for applications at the microscale or in harsh environments.

Plasmonic biosensing with tilted fiber Bragg gratings interrogated using a 512-pixel spectrometer.

Plasmonic tilted fiber Bragg gratings (TFBGs) are very efficient for fast, accurate, and minimally invasive biosensing. Their transmitted amplitude spectrum is a dense comb of narrowband cladding mode resonances (full width at half maximum < 1 nm) that is usually demodulated using highly resolved (wavelength resolution < 10 pm) devices. This work demonstrates the possibility of using a coarsely resolved spectrometer (166 pm) to read out the amplitude spectrum of a gold-coated TFBG. A refined analysis of the spectral content has allowed us to develop signal processing that provides a refractometric sensitivity of 2656 nm/RIU. This is a fivefold improvement compared to previously reported read-out techniques. Biosensing has then been successfully implemented with gold-coated TFBGs implemented in reflection mode for the detection of insulin, with specific antibodies grafted on the gold surface. Our experimental work is a first step toward the industrialization of the FBG technology, as it opens the door to fast parallel biosensing, profiting from the multiple sensing channels (up to 64) of the interrogator and its high processing speed (repetition rate up to 3 kHz).

Recovery of a highly reflective Bragg grating in DPDS-doped polymer optical fiber by thermal annealing.

We report fiber Bragg grating manufacturing in poly(methyl methacrylate) (PMMA)-based polymer optical fibers (POFs) with a diphenyl disulfide (DPDS)-doped core by means of a 266 nm pulsed laser and the phase mask technique. Gratings were inscribed with different pulse energies ranging from 2.2 mJ to 2.7 mJ. For the latter, the grating reflectivity reached 91% upon 18-pulse illumination. Though the as-fabricated gratings decayed, they were recovered by post-annealing at 80°C for 1 day, after which they showed an even higher reflectivity of up to 98%. This methodology for the fabrication of highly reflective gratings could be applied for the production of high-quality tilted fiber Bragg gratings (TFBGs) in POFs for biochemical applications.

Femtosecond laser line-by-line tilted Bragg grating inscription in single-mode step-index TOPAS/ZEONEX polymer optical fiber.

In this Letter, we demonstrate 8°-tilted fiber Bragg grating (TFBG) inscription in single-mode step-index TOPAS/ZEONEX polymer optical fibers (POFs) using a 520 nm femtosecond laser and the line-by-line (LbL) writing technique. As a result of the tilt angle and the fiber refractive index, a large spectral range of cladding mode resonances covering 147 nm is obtained. The evolution of the transmitted spectrum is analyzed as a function of the surrounding refractive index (SRI) in a large range from 1.30 to 1.50. The cutoff cladding mode shows a refractive index sensitivity of 507 nm/RIU (refractive index unit). For single-resonance tracking near the cutoff mode, the sensitivity is at least 6 nm/RIU, depending on the exact wavelength position of the cladding modes. The main originality of our work is that it produces, for the first time, to the best of our knowledge, a TFBG in POF that operates in the refractive index range of aqueous solutions. The sensing capability for a large range of refractive index values is also relevant for (bio)chemical sensing in different media.

Instrumented Flexible Glass Structure: A Bragg Grating Inscribed with Femtosecond Laser Used as a Bending Sensor.

Fused silica glass is a material with outstanding mechanical, thermal and optical properties. Being a brittle material, it is challenging to shape. In the last decade, the manufacturing of monolithic flexible mechanisms in fused silica has evolved with the femtosecond-laser-assisted etching process. However, instrumenting those structures is demanding. To address this obstacle, this article proposes to inscribe a Bragg Grating sensor inside a flexure and interface it with an optical fibre to record the strain using a spectrum analyser. The strain sensitivity of this Bragg Grating sensor is characterized at 1.2 pm/µÏµ (1 µÏµ = 1 microstrain). Among other applications, deformation sensing can be used to record a force. Its use as a micro-force sensor is estimated. The sensor resolution is limited by our recording equipment to 30 µN over a measurement range above 10 mN. This technology can offer opportunities for surgery applications or others where precision and stability in harsh environments are required.

Influence of Annealing on Polymer Optical Fiber Bragg Grating Inscription, Stability and Sensing: A Review.

This article reviews recent research progress on the annealing effects on polymer optical fibers (POFs), which are of great importance for inscription, stability and sensing applications of fiber Bragg gratings (FBGs) in POFs due to their unique properties related to polymer molecular chains. In this review, the principle of annealing to reduce frozen-in stress in POFs drawing and different annealing timings are firstly summarized. Then, the annealing methods for POFs are introduced under several different conditions (temperature, humidity, strain, stress and solution). Afterwards, the principle of FBGs and several inscription techniques are reported. Subsequently, the annealing effects on the properties of POFs and polymer optical fiber Bragg gratings (POFBGs) quality are discussed. Finally, the influence of annealing on POFBG sensitivity is summarized. Overall, this paper provides a comprehensive overview of annealing techniques and their impact on both POFs and POFBGs. We hope that it will highlight the important progress made in this field.

Phase interrogation of plasmonic tilted fiber Bragg grating biosensors through the Jones formalism.

Gold-coated tilted fiber Bragg gratings (TFBG) are refined plasmonic biosensors, highly sensitive to surrounding refractive index (RI) changes. Their interrogation usually relies on insertion loss measurements for single input polarized light, limiting the set of exploitable features. To overcome this limitation, we trigger the Jones formalism to retrieve the polarization enabling optimized plasmonic excitation for both phase and amplitude measurements. We present an experimental phase shift with a sensitivity as high as 45835°/RIU and further assess this approach to HER2 proteins sensing at 1µg/ml. We compare this angular modality with the one relying on the insertion loss using a quality factor that takes the shift as well as the dispersion into account. This strengthens its relevance in terms of precision for ultra-small RI variations.

Partially gold-coated tilted FBGs for enhanced surface biosensing.

To date, there is clear experimental evidence that gold-coated tilted fiber Bragg gratings (TFBGs) are highly sensitive plasmonic biosensors that provide temperature-compensated detection of analytes at concentrations in the picomolar range. As most optical biosensors, they bring an evanescent wave in the surrounding medium, which makes them sensitive to both surface refractive index variations (= the useful biosensing signal) and to bulk refractive index changes (= the non-useful signal for biosensing). This dual sensitivity makes them prone to drift. In this work, we study partially gold-coated TFBGs around their cross-section. These gratings present the ability to discriminate both volume and surface refractive index changes, which is interesting in biosensing to enhance the signal-to-noise ratio. The effects induced in the TFBGs transmitted amplitude spectra were analyzed for surrounding refractive index (SRI) changes in the range 1.3360-1.3370. Then, the gold film was biofunctionalized with human epidermal growth factor receptor (HER2) aptamers using thiol chemistry. The detection of HER2 proteins (a relevant cancer biomarker) at 10-9 g/mL, 10-8 g/mL and 10-6 g/mL demonstrated the advantage to identify environmental perturbations through the bare area of the TFBGs, which is left not functionalized. The non-specific drifts that could exist in samples are eliminated and a wavelength shift only related to the surface modification is obtained.

Femtosecond laser point-by-point Bragg grating inscription in BDK-doped step-index PMMA optical fibers.

In this paper, the inscription of 2-mm-long fiber Bragg gratings (FBGs) on benzyl dimethyl ketal (BDK)-doped poly(methyl methacrylate) (PMMA) optical fibers by means of a femtosecond laser and a point-by-point FBG inscription technique is reported. The highest reflectivity of approximately 99% is obtained with a pulse energy of 68.5 nJ, showing a large refractive index modulation amplitude of 7.2 × 10-4. Afterwards, grating stabilities at room and higher temperatures of up to 80°C are investigated.

Femtosecond laser point-by-point Bragg grating inscription in BDK-doped step-index PMMA optical fibers: erratum.

An erratum is presented to correct the laser pulse energy applied on the fiber during grating fabrication in Opt. Lett.47(2), 249 (2022)10.1364/OL.450047.

Smart Railway Traffic Monitoring Using Fiber Bragg Grating Strain Gauges.

There is today ample evidence that fiber Bragg gratings (FBGs) distributed along a railway track can provide robust axle counting and bring numerous assets compared to competing technologies in this practical environment. This work brings two relevant originalities with respect to the state-of-the-art solutions. First, a study of the strain distribution in the rail cross-section is performed to determine the sensitivity according to the charge and the position on the rail. Secondly, the technology is deployed along the rail track as a smart object where the sensor head is composed of four FBG wavelength-division-multiplexed in a single telecommunication-grade optical fiber and interrogated by a miniaturized read-out device. Two FBGs ensure the detection of the train direction and another two bring the required redundancy to reach a safety integrity level (SIL) 4. The read-out unit has been specifically developed for the application and contains a vertical-cavity surface-emitting laser (VCSEL) and a photodiode driven by a high-speed microprocessor unit that processes the data and communicates the useful information, i.e., the number of axles. On-field tests confirm that the proposed approach makes the installation process easier while it democratizes the technology.

Optimization of Cladding Diameter for Refractive Index Sensing in Tilted Fiber Bragg Gratings.

This work presents an experimental investigation of the effect of chemical etching on the refractive index (RI) sensitivity of tilted fiber Bragg gratings (TFBGs). Hydrofluoric acid (HF) was used stepwise in order to reduce the optical fiber diameter from 125 µm to 13 µm. After each etching step, TFBGs were calibrated using two ranges of RI solutions: the first one with high RI variation (from 1.33679 RIU to 1.37078 RIU) and the second with low RI variation (from 1.34722 RIU to 1.34873 RIU). RI sensitivity was analyzed in terms of wavelength shift and intensity change of the grating resonances. The highest amplitude sensitivities obtained are 1008 dB/RIU for the high RI range and 8160 dB/RIU for the low RI range, corresponding to the unetched TFBG. The highest wavelength sensitivities are 38.8 nm/RIU for a fiber diameter of 100 µm for the high RI range, and 156 nm/RIU for a diameter of 40 µm for the small RI range. In addition, the effect of the etching process on the spectral intensity of the cladding modes, their wavelength separation and sensor linearity (R2) were studied as well. As a result, an optimization of the etching process is provided, so that the best trade-off between sensitivity, intensity level, and fiber thickness can be obtained.

Relevance of the Spectral Analysis Method of Tilted Fiber Bragg Grating-Based Biosensors: A Case-Study for Heart Failure Monitoring.

Optical fiber technology has rapidly progressed over the years, providing valuable benefits for biosensing purposes such as sensor miniaturization and the possibility for remote and real-time monitoring. In particular, tilted fiber Bragg gratings (TFBGs) are extremely sensitive to refractive index variations taking place on their surface. The present work comprises a case-study on the impact of different methods of analysis applied to decode spectral variations of bare and plasmonic TFBGs during the detection of N-terminal B-type natriuretic peptide (NT-proBNP), a heart failure biomarker, namely by following the most sensitive mode, peaks of the spectral envelopes, and the envelopes' crossing point and area. Tracking the lower envelope resulted in the lowest limits of detection (LOD) for bare and plasmonic TFBGs, namely, 0.75 ng/mL and 0.19 ng/mL, respectively. This work demonstrates the importance of the analysis method on the outcome results, which is crucial to attain the most reliable and sensitive method with lower LOD sensors. Furthermore, it makes the scientific community aware to take careful attention when comparing the performance of different biosensors in which different analysis methods were used.

Plasmonic sensors based on tilted Bragg gratings in multicore optical fibers.

Bare and gold-coated tilted fiber Bragg gratings (TFBGs) can nowadays be considered as a mature technology for volume and surface refractometric sensing, respectively. As for other technologies, a continuous effort is made towards the production of even more sensitive sensors, thereby enabling a high-resolution screening of the surroundings and the possible detection of rare events. To this aim, we study in this work the development of TFBG refractometers in 4-core fibers. In particular, we show that the refractometric sensitivity of the cut-off mode can reach 100 nm/RIU for a bare grating. Using another demodulation method, a tenfold sensitivity increase is obtained when tracking the extremum of the SPR (surface plasmon resonance) envelope for a gold-coated TFBG configuration. Immobilization of DNA probes was performed as a proof-of-concept to assess the high surface sensitivity of the device.

Ultra-fast fiber Bragg grating inscription in CYTOP polymer optical fibers using phase mask and 400 nm femtosecond laser.

Fiber Bragg gratings (FBGs) in cyclic transparent fluoropolymer (CYTOP) optical fiber are the subject of a lot of research as they can be of interest for many applications, such as temperature, humidity, strain, and radiation sensing. We report here a new technique to produce high quality FBGs in CYTOP fiber. It uses a femtosecond laser system operating at 400 nm and a phase mask. In contrast to previously reported results, the gratings are obtained in a few seconds with a writing power as low as 80 µW. With this setup, 2 mm-long gratings with reflectivity up to 92 % and full width at half maximum bandwidth around 0.5 nm were obtained in less than 10 s. The resonance wavelengths of the FBGs are confirmed by numerical computation in the graded-index multimode CYTOP fiber, and the mode selection characteristic of FBGs in CYTOP is investigated. Finally, the temperature sensitivity of CYTOP FBG is measured in different mode groups for heating up and cooling down, showing values independent of the mode group measured, but with a small hysteresis.

800 nm femtosecond pulses for direct inscription of FBGs in CYTOP polymer optical fiber.

We report the inscription of highly reflective fiber Bragg gratings in perfluorinated polymer (CYTOP) optical fibers using 800 nm femtosecond pulses and a line-by-line inscription method. We demonstrate that the energy for grating inscription without damage is below 27 nJ. After the writing process, we show that the grating reflectivity continues to rise for several hours. The obtained gratings show reflectivity degradation with temperature increase, while the Bragg wavelength undergoes a linear temperature dependence of 37.7 pm/°C when the humidity is controlled and the heating/cooling rate is relatively low (≤0.14∘C/min). The humidity sensitivity at a fixed temperature (25°C) is 22.3 pm/%RH. Finally, the axial strain sensitivity is determined to be 1.35 pm/µÉ›.

PfHRP2 detection using plasmonic optrodes: performance analysis.

BACKGROUND: Early malaria diagnosis and its profiling require the development of new sensing platforms enabling rapid and early analysis of parasites in blood or saliva, aside the widespread rapid diagnostic tests (RDTs). METHODS: This study shows the performance of a cost-effective optical fiber-based solution to target the presence of Plasmodium falciparum histidine-rich protein 2 (PfHRP2). Unclad multimode optical fiber probes are coated with a thin gold film to excite Surface Plasmon Resonance (SPR) yielding high sensitivity to bio-interactions between targets and bioreceptors grafted on the metal surface. RESULTS: Their performances are presented in laboratory conditions using PBS spiked with growing concentrations of purified target proteins and within in vitro cultures. Two probe configurations are studied through label-free detection and amplification using secondary antibodies to show the possibility to lower the intrisic limit of detection. CONCLUSIONS: As malaria hits millions of people worldwide, the improvement and multiplexing of this optical fiber technique can be of great interest, especially for a future purpose of using multiple receptors on the fiber surface or several coated-nanoparticles as amplifiers.