Gamma-radiation enhancement of sensing properties of FBGs in a few-mode polymer CYTOP fiber.

We investigate the effect of γ-radiation on temperature (T) and relative humidity (RH) sensitivities of polymer perfluorinated fiber Bragg gratings (FBGs). To this aim, different γ-radiation doses (80, 120, 160, and 520 kGy) were applied to a set of FBGs. We show that irradiated FBGs demonstrate an RH sensitivity rise with the received dose: from 13.3 pm/%RH for a pristine FBG up to 56.8 pm/%RH for a 520-kGy dose at 30℃. In contrast, T sensitivity decreases with radiation dose with a subsequent change of sign from positive to negative. Therefore, by experimental interpolation, T sensitivity can be eliminated at around a 160-kGy dose. This opens the possibility of designing an RH sensor with enhanced sensitivity, which at the same time is insensitive to T.

Online Gamma Radiation Monitoring Using Few-Mode Polymer CYTOP Fiber Bragg Gratings.

We investigated the gamma radiation response of fiber Bragg gratings (FBGs) inscribed in a few-mode polymer optical fiber. The fiber had a graded-index CYTOP core of 20 µm and XYLEX overclad of 250 µm in diameter. Four FBGs were exposed to gamma radiation during four irradiation sessions at a 5.3 kGy/h dose rate. The FBGs showed a linear Bragg wavelength shift with the received dose with a mean sensitivity of -3.95 pm/kGy at 43 °C. The increased temperature provides a rise in the sensitivity: it reached -10.6 pm/kGy at 58 °C. After irradiation, the FBGs showed partial recovery, which increased with the received dose. Furthermore, the FBG's reflection power decreased with the dose. This attenuation is mainly due to insertion losses caused by the radiation induced attenuation in the CYTOP fiber. Linear response to the received dose makes CYTOP FBGs attractive for gamma radiation dosimetry. However, temperature dependence of the sensitivity should be compensated in practical applications.

Properties of Fiber Bragg Grating in CYTOP Fiber Response to Temperature, Humidity, and Strain Using Factorial Design.

The characteristics of fiber Bragg grating (FBG) in cyclic transparent fluoropolymer (CYTOP) optical fiber have attracted more and more attention in recent years. However, different results of the FBG response to environmental parameters are reported. This work presents a three-variable two-level factorial experimental method to investigate the FBG response to temperature, humidity, and strain in CYTOP fiber. Two uniform FBGs are inscribed separately in CYTOP fiber with and without over-clad. With only eight measuring points, the interactions among three variable parameters are computed and the parameter sensitivities and cross-sensitivities are estimated. Similar temperature and strain sensitivities were found for both gratings, whereas significant cross-sensitivity between humidity and temperature was present only in FBG inscribed in CYTOP fiber with over-clad.

Ultra-fast fiber Bragg grating inscription in CYTOP polymer optical fibers using phase mask and 400 nm femtosecond laser.

Fiber Bragg gratings (FBGs) in cyclic transparent fluoropolymer (CYTOP) optical fiber are the subject of a lot of research as they can be of interest for many applications, such as temperature, humidity, strain, and radiation sensing. We report here a new technique to produce high quality FBGs in CYTOP fiber. It uses a femtosecond laser system operating at 400 nm and a phase mask. In contrast to previously reported results, the gratings are obtained in a few seconds with a writing power as low as 80 µW. With this setup, 2 mm-long gratings with reflectivity up to 92 % and full width at half maximum bandwidth around 0.5 nm were obtained in less than 10 s. The resonance wavelengths of the FBGs are confirmed by numerical computation in the graded-index multimode CYTOP fiber, and the mode selection characteristic of FBGs in CYTOP is investigated. Finally, the temperature sensitivity of CYTOP FBG is measured in different mode groups for heating up and cooling down, showing values independent of the mode group measured, but with a small hysteresis.

800 nm femtosecond pulses for direct inscription of FBGs in CYTOP polymer optical fiber.

We report the inscription of highly reflective fiber Bragg gratings in perfluorinated polymer (CYTOP) optical fibers using 800 nm femtosecond pulses and a line-by-line inscription method. We demonstrate that the energy for grating inscription without damage is below 27 nJ. After the writing process, we show that the grating reflectivity continues to rise for several hours. The obtained gratings show reflectivity degradation with temperature increase, while the Bragg wavelength undergoes a linear temperature dependence of 37.7 pm/°C when the humidity is controlled and the heating/cooling rate is relatively low (≤0.14∘C/min). The humidity sensitivity at a fixed temperature (25°C) is 22.3 pm/%RH. Finally, the axial strain sensitivity is determined to be 1.35 pm/µÉ›.

Effective Cleaving Parameters for Multimode Gradient Index CYTOP Polymer Fiber.

We experimentally address simple, low-cost and effective methods for the cleaving of multimode CYTOP optical fibers using razor blades. The quality of fiber end-face preparation depends on various parameters. The necessity of the near-field intensity pattern inspection for adequate evaluation of cleaved fiber end-faces is demonstrated. Razor blades of different manufacturers are evaluated for manual cleaving, as well as automated cleaving with controlled speed and temperature. The cleaving technique with both slowed motion of the razor blade and increased temperature up to 90 °C demonstrated the best quality of fiber end-faces. Typical cleaving defects are highlighted, whereas the cleave quality was characterized in terms of the light intensity profile emitted by the fiber in near field.