Characterization, antioxidant and antitumor activities of phenolic compounds from Amomum villosum Lour.

Amomum villosum Lour. (A. villosum), known as Sharen in China, is widely used for culinary and medicinal purposes due to containing a diverse set of bioactive compounds. In this study, the optimum ethanol extraction process was optimized and the composition and biological activities (antioxidant and antitumor) of five different fractions (dichloromethane, petroleum ether, ethyl acetate, n-butanol and H2O) extracted from the ethanol extract of A. villosum were investigated. The results showed that the optimal extraction conditions were extraction temperature 80°C, extraction time 120 min, ethanol concentration 40% and solid-liquid ratio 1:25 g/mL. Moreover, 35 bioactive compounds were successfully identified by UPLC-ESI-QTOF-MS/MS from five factions for the first time, including 12 phenolic acids and derivatives, 2 organic acids, 12 flavonoids and derivatives, 2 oxylipins and 7 proanthocyanidins. Among them, ethyl acetate fraction (Fr-EtOAc) exhibited the highest content of total phenolic (374.01 mg GAE/g DW) and flavonoid (93.11 mg RE/g DW), where vanillic acid, catechin, epicatechin and protocatechuic acid were the predominant phenolic compounds that accounting for 81.65% of the quantified bioactive compounds. In addition, Fr-EtOAc demonstrated excellent total antioxidant activity (IC50 of DPPH and ABTS assays were 0.23, 0.08 mg/mL, respectively, and FRAP assay was 322.91 mg VCE/100 g DW) and antitumor activity (1,000 µg/mL, 79.04% inhibition rate). The results could provide guidance for the industrial production and application of A. villosum.

Preparation of pectin/poly(m-phenylenediamine) microsphere and its application for Pb2+ removal.

Novel pectin/poly(m-phenylenediamine) (P/PmPDA) microspheres with different content of PmPDA were prepared by assembling PmPDA on the surface of pectin microsphere. The successful preparation was confirmed by the results of Fourier Transform Infrared spectra (FTIR), scanning electron microscopy (SEM) and elemental analysis. Compared with pectin microsphere, the Pb2+ adsorption performance of P/PmPDA microspheres was significantly improved. The results of batch adsorption experiments were in good agreement with the Langmuir isotherm model for Pb2+ adsorption, indicating the adsorption was monolayer. The maximum adsorption capacity of Pb2+ was found to be 390.9 mg/g. The kinetic adsorption process was well described by the pseudo-second-order model and chemical adsorption dominated the adsorption process. The potential mechanisms of Pb2+ adsorption were speculated as ion exchange and chelation, which were supported by X-ray photoelectron spectroscopy (XPS). The P/PmPDA microspheres showed good recyclability after five adsorption/desorption cycles. All these results indicated the potential of P/PmPDA microspheres for removing Pb2+.

A new pre-gelatinized starch preparing by gelatinization and spray drying of rice starch with hydrocolloids.

Rice starch with hydrocolloids (pectin, xanthan gum, sodium alginate or ι-carrageenan) was gelatinized and subsequently spray dried to prepare pre-gelatinized rice starch (PRS) with hydrocolloids (PRS-H). The PRS-H displayed concave granular shape with amorphous structure, indicating rice starch in PRS-H was completely gelatinized. Cold paste viscosity of PRS-H was enhanced in comparison with that of PRS. Especially, xanthan and ι-carrageenan increased cold paste viscosity of PRS-H more than pectin and alginate did. Cold paste viscosity of physically mixed PRS and hydrocolloids (PRS+H), and flow behavior of hydrocolloids themselves as well as gelatinized starch-hydrocolloids without spray drying (GRS-H) indicated interactions existed between starch and hydrocolloids during the preparation. Swelling power, water solubility index, and dynamic viscoelastic properties of PRS-H were also adjusted by different hydrocolloids. These results showed that premixing hydrocolloids with starch before gelatinization in method of spray drying would be a suitable methodology for manufacture PRS with altered properties.