Effects of NaOCl, EDTA and MTAD when applied to dentine on stress distribution in post-restored roots with flared canals.

AIM: To evaluate the effect of NaOCl, EDTA and MTAD on the stress distribution and levels in roots with flared canals and three different aesthetic post systems using finite element stress analysis (FEA). METHODOLOGY: Three-dimensional (3D) FEA models simulating a maxillary incisor with excessive structural loss and flared root canals were created. The dentine of the first models of each post group was assumed as homogenous, whereas the others were deemed as having their elastic modulus affected up to 100 µm deep as a result of irrigation protocol (5.25 NaOCl, 17% EDTA and MTAD for 2 h). A sound incisor tooth model was used as the control. Restorations were created according to the post system used (pre-fabricated fibre post (PFP)), polyethylene fibre (Ribbond) post and core build-up (RBP), and one-piece milled zirconia post and core (ZP). Ceramic crowns were added to the models. A 300-N static load was applied at the centre of the palatal surface of the models to calculate the stress distributions. The SolidWorks/Cosmosworks structural analysis programmes were used for FEA analysis. Results were presented by considering von Mises criteria. RESULTS: The analysis of the von Mises stresses revealed that RBP created less stress in the remaining root dentine when compared to PFP and ZP. ZP maintained the stresses inside its body and reduced stress on the palatal surface of the root; however, it forwarded more stress towards the apical area. NaOCl-, EDTA- and MTAD-treated dentine increased the stresses within the root structure regardless of the effect of the post system used (11-15.4 MPa for PFP, 9.5-13.02 MPa for RBP and 14.2 MPa for ZP). Amongst the irrigation solutions used, EDTA and MTAD increased the stresses more than NaOCl in all models. All the irrigation solutions showed the same stress levels and distributions in the ZP model. CONCLUSION: NaOCl-, EDTA- and MTAD- treated dentine and a rigid post with high elastic modulus may increase fracture risk in roots with flared canals by increasing the stresses within root dentine. Therefore, solutions that alter the elastic modulus of dentine less (such as NaOCl) or an individually shaped post-core system constructed with a material that has an elastic modulus close to dentine (polyethylene fibre) should be used in weak roots.

Volumetric measurements of the subcortical structures of healthy adult brains in the Turkish population.

BACKGROUND: The interest in the morphological development of brain structures during childhood and adolescence arises from discussions on subcortical anomalies and sexual dimorphism, from adolescent changes in cognitive functions supported by cortical and subcortical structures to a wide range of childhood neuropsychiatric diseases. This study aims to investigate the subcortical structures regarding age/gender changes in the healthy adult human brain using web-based volBrain. MATERIALS AND METHODS: In this study, 303 normal healthy adults (males and females) were examined using a 1.5 T unit with a 20-channel head coil. RESULTS: The volumes of white matter, grey matter, total brain, cerebrospinal fluid, and total intracranial volume were significantly higher in males than those in females. Our analysis revealed a significantly larger accumbens volume in females. With the age of less than or equal to 50 years, older males were found to have higher total lateral ventricle, putamen, thalamus, amygdala, cerebrum, white matter and grey matter volumes than females. In the age group of 50 years and older mean total volumes of thalamus, globus pallidus and accumbens were higher in females than those in males. Right hemisphere volumes in younger and older age groups were higher except for caudate volume in the older age group; the mean of caudate was significantly higher in females than those in males. CONCLUSIONS: These conclusions might be important for the explanation of the effects of gender and age in cross-sectional structural magnetic resonance imaging studies. Also, knowing the volume changes of the subcortical structures can provide convenience about the prevention, diagnosis, and treatment of various neuromental disorders.

Monoblocks in root canals: a finite elemental stress analysis study.

AIM: To investigate using finite element stress analysis (FEA) primary, secondary and tertiary monoblocks created either by adhesive resin sealers or by different adhesive posts and to evaluate the effect of interfaces on stress distribution in incisor models. METHODOLOGY: Seven maxillary incisor FEA models representing different monoblocks using several materials were created as follows: (a) primary monoblock with Mineral Trioxide Aggregate; (b) secondary monoblock with sealer (MetaSEAL) and Resilon; (c) tertiary monoblock with EndoREZ; (d) primary monoblock with polyethylene fibre post-core (Ribbond); (e) secondary monoblock with glass-fibre post and resin cement; (f) tertiary monoblock with bondable glass-fibre post; (g) tertiary monoblock with silane-coated ceramic post. A 300 N load was applied from the palatal surface of the crown with a 135° angle to the tooth long axis. Materials used in the study were assumed to be homogenous and isotropic except the glass-fibre post; the results are expressed in terms of von Mises criteria. RESULTS: Maximum stresses were concentrated on force application areas (18-22.1 MPa). The stresses within the models increased with the number of interfaces both for the monoblocks created by the sealers (1.67-8.33 MPa) and for the monoblocks created by post-core systems (1.67-11.7 MPa). CONCLUSIONS: Stresses within roots increased with an increase in the number of the adhesive interfaces. Creation of a primary monoblock within the root canal either by an endodontic sealer or with an adhesive post-core system can reduce the stresses that occur inside the tooth structure.

Effects of cantilever design and material on stress distribution in fixed partial dentures--a finite element analysis.

The purpose of this study was to examine the stress distribution in distal cantilevered fixed partial dentures (FPDs) that are designed with different cantilever morphology and made from different restorative materials. The finite element (FE) method was used to create models of two restoration types; metal-ceramic and an all-ceramic FPDs. Both models were designed with distal cantilevers involving the first and second premolars as abutments and cantilever extension involving at the premolar or molar. The width of connector between the cantilever and the primary abutment restoration was 2.25 mm. The load applied during the FE analysis was positioned at the cusp tips of all teeth. The FE analysis of the models revealed that Von Mises stress values with maximum stress concentrations were observed on connectors of distal cantilevers. Stress concentration sites were also observed at the distal cervical area of the second premolar tooth. Models with premolar cantilever extensions restored with all-ceramic induced lower Von Mises stress values than metal-ceramic restorations, however models with molar cantilever extensions restored with all-ceramic restorations induced higher Von Misses stress values than metal-ceramic restorations. If the distal cantilever length and restorative material is appropriately chosen, the failure frequency may be reduced. All ceramic can be used as restorative material, when the cantilevers length is not more than the mesiodistal dimension of a premolar tooth and metal-ceramic restorations can be used in longer situations.