Distal-third clavicle fracture fixation: a biomechanical evaluation of fixation.

BACKGROUND: Approximately 25% of distal clavicle fractures are unstable. Unstable patterns have longer times to union and higher nonunion rates. Stable restoration of the distal clavicle is important in decreasing the nonunion rate in distal clavicle fractures. The purpose of this study was to biomechanically compare operative constructs for the treatment of unstable, comminuted distal-third clavicle fractures in a cadaveric model using a locking plate and coracoclavicular reconstruction. We hypothesized that the combination of coracoclavicular reconstruction and a distal clavicle locking plate is biomechanically superior to either construct used individually. MATERIALS AND METHODS: An unstable distal clavicle fracture was created in 21 thawed fresh-frozen cadaveric specimens. The 21 specimens were divided into 3 treatment groups of 7: distal-third locking plate, acromioclavicular (AC) TightRope (Arthrex, Naples, FL, USA), and distal-third locking plate and AC TightRope together. After fixation, each specimen was cyclically tested with recording of displacement to determine the stiffness and stability of each construct, followed by load-to-failure testing in tension and compression to determine the maximum load. RESULTS: The combined construct of the locking distal clavicle plate and coracoclavicular reconstruction resulted in increased stiffness, maximum resistance to compression, and decreased displacement compared with either construct alone. CONCLUSION: Greater fracture stability was achieved with the combination of the AC TightRope and locking clavicle plate construct than with either alone, suggesting a possibility for increased fracture-healing rates.

Spatial assignment of emissions using a new locomotive emissions model.

Estimates of fuel use and air pollutant emissions from freight rail currently rely highly on aggregate methods and largely obsolete data which offer little insight into contemporary air quality problems. Because the freight industry is for the most part privately held and data are closely guarded for competitive reasons, the challenge is to produce robust estimates using current reporting requirements, while accurately portraying the spatial nature of freight rail impacts. This research presents a new spatially resolved model for estimating air pollutant emissions (hydrocarbons, carbon monoxide, nitrogen oxides, particulate matter less than 10 µm in diameter, sulfur dioxide, and carbon dioxide) from locomotives. Emission estimates are based on track segment level data including track grade, type of train traffic (bulk, intermodal, or manifest) and the local locomotive fleet (EPA tier certification level and fuel efficiency). We model the California Class I freight rail system and compare our results to regional estimates from the California Air Resources Board and to estimates following U.S. Environmental Protection Agency guidance. We find that our results vary considerably from the other methods depending on the region or corridor analyzed. We also find large differences in fuel and emission intensity for individual rail corridors.

Biomechanical Head-to-Head Comparison of 2 Sutures and the Giftbox Versus Bunnell Techniques for Midsubstance Achilles Tendon Ruptures.

BACKGROUND: Acute midsubstance Achilles tendon ruptures are a common orthopaedic problem for which the optimal repair technique and suture type remain controversial. Head-to-head comparisons of current fixation constructs are needed to establish which stitch/suture combination is most biomechanically favorable. HYPOTHESIS: Of the tested fixation constructs, Giftbox repairs with Fiberwire will exhibit superior stiffness and strength during biomechanical testing. STUDY DESIGN: Controlled laboratory study. METHODS: Two biomechanical trials were performed, isolating stitch technique and suture type, respectively. In trial 1, 12 transected fresh-frozen cadaveric Achilles tendon pairs were randomized to receive either the Giftbox-modified Krackow or the Bunnell stitch with No. 2 Fiberwire suture. Each repair underwent cyclic loading, oscillating between 10 and 100 N at 2 Hz for 1000 cycles, with repair gapping measured at 500 and 1000 cycles. Load-to-failure testing was then performed, and clinical and catastrophic failure values were recorded. In trial 2, 10 additional paired cadaveric Achilles tendons were randomized to receive a Giftbox repair with either No. 2 Fiberwire or No. 2 Ultrabraid. Testing and data collections protocols in trial 2 replicated those used in trial 1. RESULTS: In trial 1, the Bunnell group had 2 failures during cyclic loading while the Giftbox had no failures. The mean tendon gapping after cyclic loading was significantly lower in the Giftbox repairs (0.13 vs 2.29 mm, P = .02). Giftbox repairs were significantly stiffer than Bunnell (47.5 vs 38.7 N/mm, P = .019) and showed more tendon elongation (5.9 ± 0.8 vs 4.5 ± 1.0 mm, P = .012) after 1000 cycles. Mean clinical load to failure was significantly higher for Giftbox repairs (373 vs 285 N, P = .02), while no significant difference in catastrophic load to failure was observed (mean, 379 vs 336 N; P = .61). In trial 2, there were no failures during cyclic loading. The Giftbox + Fiberwire repairs recorded higher clinical load-to-failure values compared with Giftbox + Ultrabraid (mean, 361 vs 239 N; P = .005). No other biomechanical differences were observed in trial 2. CONCLUSION: Simulated early rehabilitation biomechanical testing showed that Giftbox-modified Krackow Achilles repair technique with Fiberwire suture was stronger and more resistant to gap formation at the repair site than combinations that incorporated the Bunnell stitch or Ultrabraid suture. CLINICAL RELEVANCE: A more in-depth understanding of the biomechanical properties of the Giftbox repair will help inform surgical decision making because stronger repairs are less likely to fail during accelerated postoperative rehabilitation.

Suture-Only Repair Versus Suture Anchor-Augmented Repair for Achilles Tendon Ruptures With a Short Distal Stump: A Biomechanical Comparison.

BACKGROUND: Chronic noninsertional Achilles tendinosis can result in an acute Achilles tendon rupture with a short distal stump. In such tendon ruptures, there is a limited amount of adequate tissue that can hold suture, thus presenting a challenge for surgeons who elect to treat the rupture operatively. HYPOTHESIS: Adding suture anchors to the repair construct may result in biomechanically stronger repairs compared with a suture-only technique. STUDY DESIGN: Controlled laboratory study. METHODS: Nine paired Achilles-calcaneus complexes were harvested from cadavers. An artificial Achilles rupture was created 2 cm proximal to the insertion on the calcaneus. One specimen from each cadaver was assigned to a suture-only or a suture anchor-augmented repair. The contralateral specimen of the same cadaver received the opposing repair. Cyclic testing was then performed at 10 to 100 N for 2000 cycles, and load-to-failure testing was performed at 0.2 mm/s. This was followed by analysis of repair displacement, gapping at repair site, peak load to failure, and failure mode. RESULTS: The suture anchor-augmented repair exhibited a 116% lower displacement compared with the suture-only repair (mean ± SD, 1.54 ± 1.13 vs 3.33 ± 1.47 mm, respectively; P < .03). The suture anchor-augmented repair also exhibited a 45% greater load to failure compared with the suture-only repair (303.50 ± 102.81 vs 209.09 ± 48.12 N, respectively; P < .04). CONCLUSION: Suture anchor-augmented repairs performed on acute Achilles tendon ruptures with a short distal stump are biomechanically stronger than suture-only repairs. CLINICAL RELEVANCE: Our results support the use of suture anchor-augmented repairs for a biomechanically stronger construct in Achilles tendon ruptures with a short distal stump. Biomechanically stronger repairs may lead to less tendon repair gapping and failure, increasing the ability to start early active rehabilitation protocols and thus improving patient outcomes.

Adeno-Associated Virus 5 Transduces Adipose-Derived Stem Cells with Greater Efficacy Than Other Adeno-Associated Viral Serotypes.

Adipose-derived stem cells (ASCs) have shown potential in the treatment of a myriad of diseases; however, infusion of cells alone is unlikely to provide the full range of potential therapeutic applications. Transient genetic manipulation of ASCs could increase their repair and regeneration characteristics in a disease-specific context, essentially transforming them into drug-eluting depots. The goal of this study was to determine the optimal parameters necessary to transduce ASCs with recombinant adeno-associated virus (rAAV), an approved gene therapy vector that has never been associated with disease. Transduction and duration of gene expression of the most common recombinant AAV vectors were tested in this study. Among all tested serotypes, rAAV5 resulted in both the highest and longest term expression. Furthermore, we determined the glycosylation profile of ASCs before and after neuraminidase treatment and demonstrate that rAAV5 transduction requires plasma membrane-associated sialic acid. Future studies will focus on the optimization of gene delivery to ASCs, using rAAV5 as the vector of choice, to drive biological drug delivery, engraftment, and disease correction.

Cannulated screw with solid core insert: stronger than cannulated screws.

We conducted a study to determine if there is a significant difference in ultimate load, yield strength, and fatigue strength between solid core screws and cannulated screws and if a solid core insert placed inside a cannulated screw would have biomechanical effects similar to those of a solid core screw. Five screw designs were tested: Synthes 4.5-mm solid core and 4.5-mm cannulated and our prototype 4.0-mm solid core, 4.0-mm cannulated, and 4.0-mm cannulated with solid core insert. Biomechanical testing with 3-point bending was used to determine ultimate load, yield strength, and cycles to failure for 6 screws of each design. Ultimate load, yield strength, and cycles to failure were significantly (P < .05) lower in the Synthes 4.5-mm cannulated screws than in the Synthes solid core screws and significantly lower in the prototype cannulated screws than in the prototype solid core screws (P < .05) and prototype cannulated screws with solid core inserts (P < .05). There was no significant difference (P > .05) in ultimate load, yield strength, or cycles to failure between the prototype cannulated screws with solid core inserts and the prototype solid core screws.

Knotted versus knotless suture bridge repair of the achilles tendon insertion: a biomechanical study.

BACKGROUND: Surgical treatment of insertional Achilles tendinopathy often involves detachment and debridement of the Achilles tendon insertion. A recent study has shown that knotted suture bridge fixation of the Achilles to the calcaneus is biomechanically superior to single-row fixation, but there is an absence of literature on the use of different suture bridge constructs to repair the Achilles tendon. HYPOTHESIS: There will be no significant difference in the load to failure, mode of failure, tendon strain, tendon stiffness, repair site gapping, or footprint size when comparing knotted suture bridge repair to knotless suture bridge repair of the Achilles tendon after detachment for insertional Achilles tendinopathy. STUDY DESIGN: Controlled laboratory study. METHODS: A single specimen from each pair of 10 cadaveric Achilles tendons was randomized to 1 of 2 Achilles insertion repair groups: knotted (n = 10) or knotless (n = 10) suture bridge repair. Repaired footprint size was measured, and then cyclic testing from 10 to 100 N for 2000 cycles was performed. This was followed by measurement of tendon strain, repair site displacement, load to failure, and tendon stiffness. RESULTS: The knotted suture bridge repair had a significantly higher load to failure compared with the knotless suture bridge (mean ± SD, 317.8 ± 93.6 N vs 196.1 ± 12.1 N, respectively; P = .001). All constructs failed at the tendon-suture interface. Tendon strain after cyclic testing was significantly greater in the knotless (1.20 ± 1.05) compared with the knotted (0.39 ± 0.4) suture repair groups (P = .011). There was no significant difference in footprint size between the knotted (230.3 ± 63.3 mm(2)) and knotless (248.5 ± 48.8 mm(2)) groups (P = .40). There was also no significant difference in stiffness (knotted = 76.4 ± 8.0 N/mm; knotless = 69.6 ± 10.9 N/mm; P = .17) and repair site displacement after cyclic testing (knotted = 2.8 ± 1.2 mm; knotless = 3.6 ± 1.1 mm; P = .17). CONCLUSION: During suture bridge repair of the Achilles tendon after detachment, knots at the proximal suture anchors significantly improve the biomechanical strength of the repair. CLINICAL RELEVANCE: This study demonstrated that the knotless suture bridge repair had a significantly lower load to failure than the knotted suture bridge. Surgeons should be aware of these biomechanical differences, as they influence the postoperative rehabilitation protocol and may lead to higher surgical complication rates.