Analysis of the impact of temperature on the spectral shift in ultraviolet hyperspectral imaging spectrometers.

The imaging spectrometer's high performance in practical applications may be compromised by environmental factors, particularly temperature variations, posing a challenge to its stability. Temperature fluctuations can induce spectral shift, directly impacting the accuracy of spectral measurements, subsequently influencing the precision of radiometric measurements. To address this issue, this study investigates a dual-channel UV imaging spectrometer. This instrument boasts a wavelength calibration accuracy of 0.01 nm. This paper conducts an in-depth analysis of the various mechanisms through which temperature changes influence the spectral line offset in the imaging spectrometer, integrating actual orbital temperature data to discuss the instrument's temperature load settings. The impact of temperature on spectral shift is examined using finite element analysis and optical design software. Estimations of spectral shift were made based on temperature variations. Simulation results indicated that the maximum deviation of spectral shift is estimated at 0.018 nm under a temperature condition of 16 ± 1°C. Under a more controlled orbital temperature condition (16 ± 0.3°C), the maximum deviation of spectral shift decreased to 0.01 nm. Experimental data revealed that at 16 ± 1°C, the maximum deviation of spectral shift did not exceed 0.01 nm. This effectively corroborates our theoretical analysis. The relationship between temperature and spectral shift offers a crucial theoretical foundation for calibrating spectral measurements and managing the thermal conditions of the instrument.

Emodin Blocks mPTP Opening and Improves LPS-Induced HMEC-1 Cell Injury by Upregulation of ATP5A1.

BACKGROUND: Emodin has been shown to exert anti-inflammatory and cytoprotective effects. Our study aimed to identify a novel anti-inflammatory mechanism of emodin. METHODS: An LPS-induced model of microvascular endothelial cell (HMEC-1) injury was constructed. Cell proliferation was examined using a CCK-8 assay. The effects of emodin on reactive oxygen species (ROS), cell migration, the mitochondrial membrane potential (MMP), and the opening of the mitochondrial permeability transition pore (mPTP) were evaluated. Actin-Tracker Green was used to examine the relationship between cell microfilament reconstruction and ATP5A1 expression. The effects of emodin on the expression of ATP5A1, NALP3, and TNF-α were determined. After treatment with emodin, ATP5A1 and inflammatory factors (TNF-α, IL-1, IL-6, IL-13 and IL-18) were examined by Western blotting. RESULTS: Emodin significantly increased HMEC-1 cell proliferation and migration, inhibited the production of ROS, increased the mitochondrial membrane potential, and blocked the opening of the mPTP. Moreover, emodin could increase ATP5A1 expression, ameliorate cell microfilament remodeling, and decrease the expression of inflammatory factors. In addition, when ATP5A1 was overexpressed, the regulatory effect of emodin on inflammatory factors was not significant. CONCLUSION: Our findings suggest that emodin can protect HMEC-1 cells against inflammatory injury. This process is modulated by the expression of ATP5A1.

Population structure analysis to explore genetic diversity and geographical distribution characteristics of wild tea plant in Guizhou Plateau.

BACKGROUND: Tea, the second largest consumer beverage in the world after water, is widely cultivated in tropical and subtropical areas. However, the effect of environmental factors on the distribution of wild tea plants is unclear. RESULTS: A total of 159 wild tea plants were collected from different altitudes and geological types of the Guizhou Plateau. Using the genotyping-by-sequencing method, 98,241 high-quality single nucleotide polymorphisms were identified. Genetic diversity, population structure analysis, principal component analysis, phylogenetic analysis, and linkage disequilibrium were performed. The genetic diversity of the wild tea plant population from the Silicate Rock Classes of Camellia gymnogyna was higher than that from the Carbonate Rock Classes of Camellia tachangensis. In addition, the genetic diversity of wild tea plants from the second altitude gradient was significantly higher than that of wild tea plants from the third and first altitude gradients. Two inferred pure groups (GP01 and GP02) and one inferred admixture group (GP03) were identified by population structure analysis and were verified by principal component and phylogenetic analyses. The highest differentiation coefficients were determined for GP01 vs. GP02, while the lowest differentiation coefficients were determined for GP01 vs. GP03. CONCLUSIONS: This study revealed the genetic diversity and geographical distribution characteristics of wild tea plants in the Guizhou Plateau. There are significant differences in genetic diversity and evolutionary direction between Camellia tachangensis with Carbonate Rock Classes at the first altitude gradient and Camellia gymnogyna with Silicate Rock Classes at the third altitude gradient. Geological environment, soil mineral element content, soil pH, and altitude markedly contributed to the genetic differentiation between Camellia tachangensis and Camellia gymnogyna.

Genome-wide association study of leaf-related traits in tea plant in Guizhou based on genotyping-by-sequencing.

BACKGROUND: Studying the genetic characteristics of tea plant (Camellia spp.) leaf traits is essential for improving yield and quality through breeding and selection. Guizhou Plateau, an important part of the original center of tea plants, has rich genetic resources. However, few studies have explored the associations between tea plant leaf traits and single nucleotide polymorphism (SNP) markers in Guizhou. RESULTS: In this study, we used the genotyping-by-sequencing (GBS) method to identify 100,829 SNP markers from 338 accessions of tea germplasm in Guizhou Plateau, a region with rich genetic resources. We assessed population structure based on high-quality SNPs, constructed phylogenetic relationships, and performed genome-wide association studies (GWASs). Four inferred pure groups (G-I, G-II, G-III, and G-IV) and one inferred admixture group (G-V), were identified by a population structure analysis, and verified by principal component analyses and phylogenetic analyses. Through GWAS, we identified six candidate genes associated with four leaf traits, including mature leaf size, texture, color and shape. Specifically, two candidate genes, located on chromosomes 1 and 9, were significantly associated with mature leaf size, while two genes, located on chromosomes 8 and 11, were significantly associated with mature leaf texture. Additionally, two candidate genes, located on chromosomes 1 and 2 were identified as being associated with mature leaf color and mature leaf shape, respectively. We verified the expression level of two candidate genes was verified using reverse transcription quantitative polymerase chain reaction (RT-qPCR) and designed a derived cleaved amplified polymorphism (dCAPS) marker that co-segregated with mature leaf size, which could be used for marker-assisted selection (MAS) breeding in Camellia sinensis. CONCLUSIONS: In the present study, by using GWAS approaches with the 338 tea accessions population in Guizhou, we revealed a list of SNPs markers and candidate genes that were significantly associated with four leaf traits. This work provides theoretical and practical basis for the genetic breeding of related traits in tea plant leaves.

Integrative analysis of purine metabolites and gut microbiota in patients with neuromyelitis optica spectrum disorders after mycophenolate mofetil treatment.

BACKGROUND: Neuromyelitis optica spectrum disorder (NMOSD) is a recurring inflammatory demyelinating disease that is commonly observed in Asian countries like China. Prior investigations have shown that mycophenolate mofetil (MMF) with better biocompatibility compared to azathioprine (AZA), and can prevent relapses of NMOSD, but the efficacy was controversially reported in different NMOSD cases. We aimed to explore the factors that weaken efficacy of MMF in NMOSD. METHODS: A total of 34 NMOSD patients treated with MMF were prospectively enrolled and grouped according to the therapeutic efficacy as effective group (EG, n = 23) versus less-effective group (LEG, n = 11). The purine metabolites were profiled in serum samples and gut microbiota was analyzed using 16S rRNA sequencing with stool samples from the same patients. RESULTS: Purine salvage pathway (PSP) metabolites (inosine, hypoxanthine, xanthine, guanine and uric acid) in the serum of NMOSD patients were elevated in the LEG compared to EG (p < 0.05). Additionally, the richness and microbial diversity of gut microbiota was found to be similar between EG and LEG patients. However, LEG patients had increased presence of Clostridium and Synergistes but decreased abundance of the Coprococcus genus. CONCLUSIONS: The PSP metabolites and composition of the gut microbiota were changed between patients with or without optimal clinical response after MMF treatment. This may help us to understand the pharmacodynamics of MMF in NMOSD.

A Spectral Encoding Simulator for Broadband Active Illumination and Reconstruction-Based Spectral Measurement.

Spectral reflectance or transmittance measurements provide intrinsic information on the material of an object and are widely used in remote sensing, agriculture, diagnostic medicine, etc. Most reconstruction-based spectral reflectance or transmittance measurement methods based on broadband active illumination use narrow-band LEDs or lamps combined with specific filters as spectral encoding light sources. These light sources cannot achieve the designed spectral encoding with a high resolution and accuracy due to their low degree of freedom for adjustment, leading to inaccurate spectral measurements. To address this issue, we designed a spectral encoding simulator for active illumination. The simulator is composed of a prismatic spectral imaging system and a digital micromirror device. The spectral wavelengths and intensity are adjusted by switching the micromirrors. We used it to simulate spectral encodings according to the spectral distribution on micromirrors and solved the DMD patterns corresponding to the spectral encodings with a convex optimization algorithm. To verify the applicability of the simulator for spectral measurements based on active illumination, we used it to numerically simulate existing spectral encodings. We also numerically simulated a high-resolution Gaussian random measurement encoding for compressed sensing and measured the spectral reflectance of one vegetation type and two minerals through numerical simulations. We reconstructed the spectral transmittance of a calibrated filter through an experiment. The results show that the simulator can measure the spectral reflectance or transmittance with a high resolution and accuracy.

Solid Particle Swarm Measurement in Jet Fuel Based on Mie Scattering Theory and Extinction Method.

To overcome the disadvantages of small and random samples in static detection, this paper presents a study on dynamic measurements of solid particles in jet fuel using large samples. In this paper, the Mie scattering theory and Lambert-Beer law are used to analyze the scattering characteristics of copper particles in jet fuel. We have presented a prototype for multi-angle scattered and transmitted light intensity measurements of particle swarms in jet fuel which is used to test the scattering characteristics of the jet fuel mixture with 0.5-10 µm particle sizes and 0-1 mg/L concentrations of copper particles. The vortex flow rate was converted to an equivalent pipe flow rate using the equivalent flow method. Tests were conducted at equivalent flow rates of 187, 250 and 310 L/min. Through numerical calculations and experiments, it has been discovered that the intensity of the scattering signal decreases as the scattering angle increases. Meanwhile, both the scattered light intensity and transmitted light intensity would vary with the particle size and mass concentration. Finally, the relationship equation between light intensity and particle parameters has also been summarized in the prototype based on the experimental results, which proves its detection capability.

Construction of dPCR and qPCR integrated system based on commercially available low-cost hardware.

Fluorescent quantitative PCR (qPCR) and digital PCR (dPCR) are two mainstream nucleic acid quantification technologies. However, commercial dPCR and qPCR instruments have a low integration, a high price, and a large footprint. To solve these shortcomings, we introduce a compound PCR system with both qPCR and dPCR functions. All the hardware used in this compound PCR system is commercially available and low-cost, and free software was used to realize the absolute quantification of nucleic acids. The compound PCR provides two working modes. In the qPCR mode, thermal cycling is realized by controlling the reciprocating motion of the x axis. The heating rate is 1.25 °C s-1 and the cooling rate is 1.75 °C s-1. We performed amplification experiments of the PGEM-3zf (+)1 gene. The performance level was similar to commercial qPCR instruments. In the dPCR mode, the heating rate is 0.5 °C s-1 and the cooling rate is 0.6 °C s-1. We performed the UPE-Q gene amplification and used the sequential actions of the two-dimensional mechanical sliders to scan the reaction products and used the method of regional statistics and back-inference threshold to get test results. The result we got was 1208 copies per µL-1, which was similar to expectations.

Synthesis and Characterization of Colistin-Functionalized Silica Materials for Rapid Capture of Bacteria in Water.

In this study, a new colistin-functionalized silica gel material (SiO2@NH2@COOH@CST) was synthesized after carboxylation on the surface of amino-modified silica. The main factors affecting the adsorptive properties of the material, such as the types of linkers, the linking methods, the reaction buffers and the particle sizes of carriers, were systematically investigated. The SiO2@NH2@COOH@CST was characterized by means of electron microscopy, Fourier-transform infrared spectroscopy, zeta potential measurements, etc. We demonstrated that the sorbent showed good adsorption of Gram-negative bacteria. The adsorption efficiency of E. coli on SiO2@NH2@COOH@CST was 5.2 × 1011 CFU/g, which was 3.5 times higher than that on SiO2@NH2@COOH, suggesting that electrostatic interactions between SiO2@NH2@COOH@CST and E. coli played a key role. The adsorption was quick, and was reached in 5 min. Both pseudo-first-order and pseudo-second-order kinetic models fit well with the dynamic adsorption process of SiO2@NH2@COOH@CST, indicating that physical adsorption and chemisorption might occur simultaneously during the adsorption process. SiO2@NH2@COOH@CST was successfully applied for the rapid capture of bacteria from water. The synthesized material could be used as a potential means of bacterial isolation and detection.

Temperature-dependent development and reproduction of Tarsonemus confusus (Acari: Tarsonemidae): an important pest mite of horticulture.

The tarsonemid mite Tarsonemus confusus Ewing has become an economically important pest in orchards in China. This study investigated the temperature-dependent development and reproduction of T. confusus at 15, 20, 25, 30, 33 and 35 °C. Eggs failed to hatch at 35 °C. When temperature increased from 15 to 30 °C, the developmental rate of eggs, larvae and quiescent larvae and that from egg to adulthood of both sexes significantly increased, and the time period required by females to commence oviposition significantly decreased. The lower temperature threshold (T0) for the development of eggs, larvae and quiescent larvae was between 9.3 and 12.0 °C and both sexes required about 60 degree days (DD) to complete a life cycle. Females were expected to start oviposition at 12.9 °C. The number of eggs laid, the number of female offspring produced and the egg hatch rate were significantly higher at 20, 25 and 30 °C than at 15 and 33 °C. Increasing temperature shortened the longevity of both sexes but increased the intrinsic rate of increase (rm) and finite capacity for increase (λ) with significantly shorter generation time (T) and doubling time (DT) within a temperature range of 15-30 °C. The net reproductive rate (R0) was highest at 25 °C. Results of this study may improve our knowledge of fundamental biology and ecology in genus Tarsonemus in general and in T. confusus in particular. Based on the local climate conditions, the applications of these results in predicting the seasonal population dynamics of T. confusus and timing the pest management are discussed.

User-Friendly Microfabrication Method for Complex Topological Structure and Three-Dimensional Microchannel with the Application Prospect in Polymerase Chain Reaction (PCR).

One of the most important challenges in the field of microfluidics is the rapid fabrication of microchips with complex topologies. Although the processing method of microfluidic chips has made brilliant achievements in the past 20 years, almost all traditional processing methods still face huge obstacles in the production of complex topologies and three-dimensional microchannel. Nowadays, the main methods of manufacturing microfluidic chips such as numerical control microprocessing, laser ablation, inkjet printing, photolithography, dry etching, and lithography, galvanoformung and abformung (LIGA) technology are not only inapplicable to the complex topological structure and the rapid processing of three-dimensional microfluidic chips but also rely on expensive processing equipment, complex manufacturing process, and low yield. To solve the problems of these traditional processing methods, we propose a low-cost methodology to obtain a microfluidic chip by sewing the chip pipe to the substrate with an embroidery machine as low as $6. Compared with the above-mentioned traditional microprocessing technologies, the new chip processing technology proposed by us does not involve professional microprocessing equipment and professional skills. Therefore, this new chip processing technology can significantly improve the efficiency of microprocessing.

The effect of catalytic copper pretreatments on CVD graphene growth at different stages.

The controllable synthesis of high-quality and large-area graphene by chemical vapor deposition (CVD) remains a challenge nowadays. The massive grain boundaries in graphene grown on polycrystalline Cu by CVD significantly reduce its carrier mobility, limiting its application in high-performance electronic devices. Here, we confirm that the synergetic pretreatment of Cu with electropolishing and surface oxidation is a more efficient way to further suppress the graphene nucleation density (GND) and to accelerate the growth rate of the graphene domain by CVD. With increasing the growth time, we found that the increasing amount of GND and growth rate of the graphene domain were both decreasing during the whole CVD process when the Cu surface was not oxidized. By contrast, they kept growing over time when the Cu surface was pre-oxidized, which suggested that the change trends of the effects on the GND and growth rate between the Cu surface morphology and oxygen were opposite in the CVD process. In addition, not only the domain shape, but the number of graphene domain layers were impacted as well, and a large number of irregular ellipse graphene wafers with dendritic multilayer emerged when the Cu surface was oxidized.

Analytical Separation of Closantel Enantiomers by HPLC.

Closantel is an antiparasitic drug marketed in a racemic form with one chiral center. It is meaningful to develop a method for separating and analyzing the closantel enantiomers. In this work, two enantiomeric separation methods of closantel were explored by normal-phase high-performance liquid chromatography. The influences of the chiral stationary phase (CSP) structure, the mobile phase composition, the nature and proportion of different mobile phase modifiers (alcohols and acids), and the column temperature on the enantiomeric separation of closantel were investigated in detail. The two enantiomers were successfully separated on the novel CSP of isopropyl derivatives of cyclofructan 6 and n-hexane-isopropanol-trifluoroacetic acid (97:3:0.1, v/v/v) as a mobile phase with a resolution (Rs) of about 2.48. The enantiomers were also well separated on the CSP of tris-carbamates of amylose with a higher Rs (about 3.79) when a mixture of n-hexane-isopropanol-trifluoroacetic acid (55:45:0.1, v/v/v) was used as mobile phase. Thus, the proposed separation methods can facilitate molecular pharmacological and biological research on closantel and its enantiomers.

Circular RNA hsa_circ_0000282 contributes to osteosarcoma cell proliferation by regulating miR-192/XIAP axis.

BACKGROUND: Circular RNAs (circRNAs) have emerged as a novel category of non-coding RNA, which exhibit a pivotal effect on regulating gene expression and biological functions, yet how circRNAs function in osteosarcoma (OSA) still demands further investigation. This study aimed at probing into the function of hsa_circ_0000282 in OSA. METHODS: The expressions of circ_0000282 and miR-192 in OSA tissues and cell lines were examined by quantitative real-time polymerase chain reaction (qRT-PCR), and the correlation between the expression level of circ_0000282 and clinicopathological features of OSA patients was analyzed. The expressions of X-linked inhibitor of apoptosis protein (XIAP), B-cell lymphoma-2 (Bcl-2) and Bcl-2 associated X protein (Bax) in OSA cells were assayed by Western blot. The proliferation and apoptosis of OSA cells were examined by CCK-8, BrdU and flow cytometry, respectively. Bioinformatics analysis, dual-luciferase reporter gene assay and RIP experiments were employed to predict and validate the targeting relationships between circ_0000282 and miR-192, and between miR-192 and XIAP, respectively. RESULTS: Circ_0000282 was highly expressed in OSA tissues and cell lines, which represented positive correlation with Enneking stage of OSA patients and negative correlation with tumor differentiation degree. In vitro experiments confirmed that overexpression of circ_0000282 markedly facilitated OSA cell proliferation and repressed cancer cell apoptosis in comparison to control group. Besides, knockdown of circ_0000282 repressed OSA cell proliferation and promoted apoptosis. Additionally, the binding relationships between circ_0000282 and miR-192, and between miR-192 and XIAP were validated. Circ_0000282 indirectly up-regulated XIAP expression by adsorbing miR-192, thereby playing a role in promoting cancer in OSA. CONCLUSION: Circ_0000282 was a novel oncogenic circRNA in OSA. Circ_0000282/miR-192/XIAP axis regulated OSA cell proliferation apoptosis with competitive endogenous RNA mechanism.

Charge-Transfer-Induced Noncoalescence and Chain Formation of Free Droplets under a Pulsed DC Electric Field.

Electrocoalescence technology is an important method for the demulsification of crude oil emulsion, but its development is restricted by the short circuit caused by droplet chain formation. To reveal the formation mechanism of droplet chains, the electrocoalescence behaviors of two droplets and droplet clusters under pulsed direct current (DC) electric fields are experimentally studied. The two droplets usually successively undergo complete coalescence, partial coalescence, and noncoalescence as the electric field strength increases. The critical electric field strengths for complete coalescence under pulsed DC electric fields with different frequencies are obtained. The effects of the electric field waveform and frequency on the noncoalescence characteristics of two droplets and the stability of droplet chains are explored. The droplet chains under a high-frequency electric field are more stable and longer than those under a low-frequency electric field due to the reduction of the movement distance and the generation of daughter droplets from tip streaming. The reversal of the composition of electric forces due to charge transfer is the fundamental mechanism of noncoalescence of two droplets and chain formation in the emulsion under a pulsed DC electric field.

Continuous Movement Mechanism of Oil Droplets Adhered on Surfaces with Different Wettability in the Flow Field.

In this aticle, the continuous movement patterns and characteristic parameters of oil droplets on surfaces with different wettability immersed in a laminar flow field were observed, and the change rules of the geometric parameters of oil droplets under different experimental conditions were obtained. Then, the factors influencing the continuous moving behaviors of the oil droplets were analyzed, and the continuous movement velocity of the oil droplets under different experimental conditions was demonstrated. On this basis, the change law of the continuous movement velocity of oil droplets with the flow velocity was discussed. In addition, the coupling effect of the oil drops' height, surface properties, and water flow velocity on the continuous movement of oil droplets was studied, and the critical conditions for the continuous movement were obtained. According to the critical conditions, the mathematical model which described the law of continuous motion of the oil droplets adhered on surfaces with different wettability in the laminar flow field was established. The quantitative relationships among the average continuous moving velocity of oil droplets, physical properties, geometric parameters, water flow velocity, and surface wettability were obtained, which defined the necessary conditions for the uniform and accelerated movement of oil droplets, providing an important basis for choices of suitable surface wettability and flow field conditions in practical engineering applications.

Migration and Adherence of Oil Droplets on Surfaces with Different Wettability in a Laminar Flow Field.

In this article, the rising trajectories of oil droplets near the substrates of small channels in the laminar flow field were observed using a high-speed camera. Chemical modifications were made on the surfaces of the brass sheets to change the surface properties, and the controllable regulation of the superoleophilic-superoleophobic wettability gradient was achieved. The adhesion behaviors of the oil droplets on surfaces with different wettabilities at different flow velocities were observed as well. According to the adhesion behaviors of oil droplets on surfaces with different wettabilities, a mathematical model was established to analyze water film thinning and the adherence of oil droplets on the wall in the laminar flow field. Then the quantitative relationships among the adhesion times tf of oil droplets on different wetting surfaces, oil and water properties, and surface wettability were acquired.

HPLC semi-preparative separation of diclazuril enantiomers and racemization in solution.

Diclazuril has been widely used in poultry feed for prevention and treatment of coccidiosis, and its chiral separation is rarely reported. Herein, semi-preparative separation method of diclazuril enantiomers has been developed through normal-phase high-performance liquid chromatography. Effects of chiral stationary phases, alcoholic modifiers, and column temperature on separation of diclazuril were discussed in detail. Both the single-urea-bound 4-chlorophenylcarbamoylated ß-cyclodextrin and amylose tris(3,5-dimethylphenylcarbamate)-coated chiral stationary phases showed strong ability in separation of diclazuril by using n-hexane-trifluoroacetic acid-ethanol. Then, semi-preparative separation of diclazuril was carried out through stacked injection, and the "enantiomeric excess" purities of two fractions were over 98%. Next, the electronic circular dichroism profiles of these two fractions in ethanol solution displayed the mirror image of each other in the range 360-200 nm. Moreover, effects of acidic/basic additive, time, and temperature on racemization of diclazuril enantiomers in ethanol solution have been studied in detail through normal-phase high-performance liquid chromatography. Racemization of diclazuril enantiomers was remarkably accelerated through adding triethylamine at high temperature. We envision that this systematic investigation of diclazuril at an enantiomeric level would provide valuable information in future studies involving enantioselective bioactive, metabolic, and toxicological activities.

Rapid determination of nosiheptide in feed based on dispersive SPE coupled with HPLC.

A novel, simple, and reliable method based on high-performance liquid chromatography coupled with fluorescence detection has been developed for the determination of nosiheptide in feed. The feed samples were extracted with acetonitrile 0.1% formic acid aqueous solution and then purified via a dispersive solid-phase extraction procedure using silica gel powder as the sorbent. Using a mixture of acetonitrile and 5 mM ammonium acetate solution (containing 0.1% formic acid) as the mobile phase, good separation and peak shape were obtained for nosiheptide on a Poroshell C8 column (250 × 4.6 mm id, 4 µm) via the isocratic elution program. The resulting calibration curve shows high levels of linearity (r2  > 0.999) for nosiheptide concentrations of 50-1000 µg/L. At three spiked levels, i.e., 0.500, 2.50 and 5.00 mg/kg, the intra- and interday recoveries of nosiheptide in five types of feed ranged from 78.5-96.8 and 84.9-94.2%, respectively. The intra- and interday relative standard deviations were less than 10.8%. The limits of quantification for nosiheptide in complete feed and premixes were measured as 50 and 100 µg/kg, respectively. Compared with other common adsorbents, silica gel presents stronger recovery and purification results for feed samples during the dispersive solid-phase extraction process.

Autophagy-Like Cell Death Regulates Hydrogen Peroxide and Calcium Ion Distribution in Xa3/Xa26-Mediated Resistance to Xanthomonas oryzae pv. oryzae.

The broad-spectrum and durable resistance gene Xa3/Xa26 against Xanthomonas oryzae pv. oryzae (Xoo) has been widely exploited in rice production in China. But the cytological features of the Xa3/Xa26-mediated resistance reaction have been rarely reported. This study reveals the cytological characteristics of the Xa3/Xa26-mediated resistance reaction against Xoo to uncover the functions of hypersensitive response programmed cell death (HR-PCD) in rice. Autophagy-like cell death, which was characterized by double-membrane bodies appearance in xylem parenchyma cell and mesophyll cell, was inhibited by autophagy inhibitor 3-methyladenin (3-MA). The autophagy-related genes were induced to reach a high level in resistance reaction. The hydrogen peroxide (H2O2) maintained a low concentration on the plasma membrane. The calcium ions localized on the apoplast were transferred into the vacuole. The autophagy inhibitor (3-MA) impaired Xa3/Xa26-mediated resistance by promoting the accumulation of H2O2, and inhibited the transfer of extracellular calcium ions into the vacuole in the xylem parenchyma cells and mesophyll cells. Therefore, the HR-PCD belongs to autophagy-like cell death in the Xa3/Xa26-mediated resistance reaction. These results suggest that the autophagy-like cell death participates in the Xa3/Xa26-mediated resistance by negatively regulating H2O2 accumulation, in order to abolish oxidative stress and possibly activate calcium ion signals in xylem parenchyma cells of the rice leaf.