Multiple forces facilitate the aquatic acrobatics of grasshopper and bioinspired robot.

Aquatic locomotion is challenging for land-dwelling creatures because of the high degree of fluidity with which the water yields to loads. We surprisingly found that the Chinese rice grasshopper Oxya chinensis, known for its terrestrial acrobatics, could swiftly launch itself off the water's surface in around 25 ms and seamlessly transition into flight. Biological observations showed that jumping grasshoppers use their front and middle legs to tilt up bodies first and then lift off by propelling the water toward the lower back with hind legs at angular speeds of up to 18°/ms, whereas the swimming grasshoppers swing their front and middle legs in nearly horizontal planes and move hind legs less violently (~8°/ms). Force measurement and model analysis indicated that the weight support could be achieved by hydrostatics which are proportionate to the mass of the grasshoppers, while the propulsions for motion are derived from the controlled limb-water interactions (i.e., the hydrodynamics). After learning the structural and behavioral strategies of the grasshoppers, a robot was created and was capable of swimming and jumping on the water surface like the insects, further demonstrating the effectiveness of decoupling the challenges of aquatic locomotion by the combined use of the static and dynamic hydro forces. This work not only uncovered the combined mechanisms responsible for facilitating aquatic acrobatics in this species but also laid a foundation for developing bioinspired robots that can locomote across multiple media.

Research on Defect Detection Method of Fusion Reactor Vacuum Chamber Based on Photometric Stereo Vision.

This paper addresses image enhancement and 3D reconstruction techniques for dim scenes inside the vacuum chamber of a nuclear fusion reactor. First, an improved multi-scale Retinex low-light image enhancement algorithm with adaptive weights is designed. It can recover image detail information that is not visible in low-light environments, maintaining image clarity and contrast for easy observation. Second, according to the actual needs of target plate defect detection and 3D reconstruction inside the vacuum chamber, a defect reconstruction algorithm based on photometric stereo vision is proposed. To optimize the position of the light source, a light source illumination profile simulation system is designed in this paper to provide an optimized light array for crack detection inside vacuum chambers without the need for extensive experimental testing. Finally, a robotic platform mounted with a binocular stereo-vision camera is constructed and image enhancement and defect reconstruction experiments are performed separately. The results show that the above method can broaden the gray level of low-illumination images and improve the brightness value and contrast. The maximum depth error is less than 24.0% and the maximum width error is less than 15.3%, which achieves the goal of detecting and reconstructing the defects inside the vacuum chamber.

Tensile mechanical properties and finite element simulation of the wings of the butterfly Tirumala limniace.

This study examined the morphological characteristics and mechanical properties of the wings of Tirumala limniace. The wings of this butterfly, including the forewings and hindwings, are composed mainly of a flexible wing membrane and supporting wing veins. Scanning electron microscopy was employed to observe specific positions of the wing membrane and veins and reveal the morphological characteristics. Tensile experiments were conducted to evaluate the mechanical properties of the wings and proved that the multifiber layer structures have a significantly fixed orientation of fiber alignment. A butterfly wing model reconstructed in reverse based on the finite element method was used to analyze the static characteristics of the wing structure in detail. Evaluation of stress and strain after applying uniform loading, perpendicular loading, and torsion revealed that minor wing deformation occurred and was concentrated near the main wing vein, which verifies the steadiness of the butterfly wing structure. Additionally, the flapping of butterfly wings was simulated using computational fluid dynamics to study the flow field near the butterfly wings and the distribution of pressure gradient on the wings. The results confirmed the effect of wing veins on maintaining the flight performance.

[Research on Vessel Segmentation and Extraction Method Based on Improved 2D Gabor Features].

This study proposed a vessel segmentation method based on Gabor features. According to the eigenvector of Hessian matrix of each pixel in the image, the vessel direction of each point was obtained to set the direction angle of Gabor filter, and the Gabor features of different vessel width at each point were extracted to establish the 6D vectors of each point. By reducing the dimension of the 6D vector, the 2D vector of each point was obtained and fused with the original image G channel. U-Net neural network was used to classify the fused image to segment vessels. The experimental results of this method in DRIVE dataset showed that this method had a good effect on the detection of small vessels and vessels at the intersection.

Lateral undulation of the flexible spine of sprawling posture vertebrates.

Sprawling posture vertebrates have a flexible spine that bends the trunk primarily in the horizontal plane during locomotion. By coordinating cyclical lateral trunk flexion and limb movements, these animals are very mobile and show extraordinary maneuverability. The dynamic and static stability displayed in complex and changing environments are highly correlated with such lateral bending patterns. The axial dynamics of their compliant body can also be critical for achieving energy-efficient locomotion at high velocities. In this paper, lateral undulation is used to characterize the bending pattern. The production of ground reaction forces (GRFs) and the related center of mass (COM) dynamics during locomotion are the fundamental mechanisms to be considered. Mainly based on research on geckos, which show unrestricted movement in three-dimensional space, we review current knowledge on the trunk flexibility and waveforms of lateral trunk movement. We investigate locomotion dynamics and mechanisms underlying the lateral undulation pattern. This paper also provides insights into the roles of this pattern in obtaining flexible and efficient walking, running, and climbing. Finally, we discuss the potential application of lateral undulation patterns to bio-inspired robotics.

The biomechanics of tree frogs climbing curved surfaces: a gripping problem.

The adhesive mechanisms of climbing animals have become an important research topic because of their biomimetic implications. We examined the climbing abilities of hylid tree frogs on vertical cylinders of differing diameter and surface roughness to investigate the relative roles of adduction forces (gripping) and adhesion. Tree frogs adhere using their toe pads and subarticular tubercles, the adhesive joint being fluid-filled. Our hypothesis was that on an effectively flat surface (adduction forces on the largest 120 mm diameter cylinder were insufficient to allow climbing), adhesion would effectively be the only means by which tree frogs could climb, but on the 44 and 13 mm diameter cylinders, frogs could additionally utilise adduction forces by gripping the cylinder either with their limbs outstretched or by grasping around the cylinder with their digits, respectively. The frogs' performance would also depend on whether the surfaces were smooth (easy to adhere to) or rough (relatively non-adhesive). Our findings showed that climbing performance was highest on the narrowest smooth cylinder. Frogs climbed faster, frequently using a 'walking trot' gait rather than the 'lateral sequence walk' used on other cylinders. Using an optical technique to visualise substrate contact during climbing on smooth surfaces, we also observed an increasing engagement of the subarticular tubercles on the narrower cylinders. Finally, on the rough substrate, frogs were unable to climb the largest diameter cylinder, but were able to climb the narrowest one slowly. These results support our hypotheses and have relevance for the design of climbing robots.

The use of clamping grips and friction pads by tree frogs for climbing curved surfaces.

Most studies on the adhesive mechanisms of climbing animals have addressed attachment against flat surfaces, yet many animals can climb highly curved surfaces, like twigs and small branches. Here we investigated whether tree frogs use a clamping grip by recording the ground reaction forces on a cylindrical object with either a smooth or anti-adhesive, rough surface. Furthermore, we measured the contact area of fore and hindlimbs against differently sized transparent cylinders and the forces of individual pads and subarticular tubercles in restrained animals. Our study revealed that frogs use friction and normal forces of roughly a similar magnitude for holding on to cylindrical objects. When challenged with climbing a non-adhesive surface, the compressive forces between opposite legs nearly doubled, indicating a stronger clamping grip. In contrast to climbing flat surfaces, frogs increased the contact area on all limbs by engaging not just adhesive pads but also subarticular tubercles on curved surfaces. Our force measurements showed that tubercles can withstand larger shear stresses than pads. SEM images of tubercles revealed a similar structure to that of toe pads including the presence of nanopillars, though channels surrounding epithelial cells were less pronounced. The tubercles' smaller size, proximal location on the toes and shallow cells make them probably less prone to buckling and thus ideal for gripping curved surfaces.

How do the substrate reaction forces acting on a gecko's limbs respond to inclines?

Locomotion is an essential character of animals, and excellent moving ability results from the delicate sensing of the substrate reaction forces (SRF) acting on body and modulating the behavior to adapt the motion requirement. The inclined substrates present in habitats pose a number of functional challenges to locomotion. In order to effectively overcome these challenges, climbing geckos execute complex and accurate movements that involve both the front and hind limbs. Few studies have examined gecko's SRF on steeper inclines of greater than 90°. To reveal how the SRFs acting on the front and hind limbs respond to angle incline changes, we obtained detailed measurements of the three-dimensional SRFs acting on the individual limbs of the tokay gecko while it climbed on an inclined angle of 0-180°. The fore-aft forces acting on the front and hind limbs show opposite trends on inverted inclines of greater than 120°, indicating propulsion mechanism changes in response to inclines. When the incline angles change, the forces exerted in the normal and fore-aft directions by gecko's front and hind limbs are reassigned to take full advantage of limbs' different roles in overcoming resistance and in propelling locomotion. This also ensures that weight acts in the angle range between the forces generated by the front and hind limbs. The change in the distribution of SRF with a change in the incline angle is directly linked to the favorable trade-off between locomotive maneuverability and stability.

Design and Motion Control of Master-Slave Control Endotracheal Intubation Robot.

BACKGROUND: Master-slave remote control technology allows patients to be treated promptly during transport and also reduces the risk of contagious infections. Endotracheal intubation, guided by endoscopy and a master-slave system, enables doctors to perform the procedure efficiently and accurately. METHODS: In this paper, we present the development of a master-slave controlled endotracheal intubation robot (EIR). It is based on operation incremental mapping, a weighted recursive average filtering method to reduce vibration, and a virtual fixture designed to reduce mishandling in minimally invasive surgery. RESULTS: Simulation analysis of the master-slave control demonstrates that the weighted recursive average filtering method effectively reduces vibration, while the virtual fixture assists in confining the operator's movement within a delimited area. Experimental validation confirms the validity of the robot's structural design and control method. CONCLUSIONS: The developed robot successfully achieves the necessary motion for endotracheal intubation surgery through master-slave control.

Biomimetic lizard robot for adapting to Martian surface terrain.

The exploration of the planet Mars still is a top priority in planetary science. The Mars surface is extensively covered with soil-like material. Current wheeled rovers on Mars have been occasionally experiencing immobilization instances in unexpectedly weak terrains. The development of Mars rovers adaptable to these terrains is instrumental in improving exploration efficiency. Inspired by locomotion of the desert lizard, this paper illustrates a biomimetic quadruped robot with structures of flexible active spine and toes. By accounting for spine lateral flexion and its coordination with four leg movements, three gaits of tripod, trot and turning are designed. The motions corresponding to the three gaits are conceptually and numerically analyzed. On the granular terrains analog to Martian surface, the gasping forces by the active toes are estimated. Then traversing tests for the robot to move on Martian soil surface analog with the three gaits were investigated. Moreover, the traversing characteristics for Martian rocky and slope surface analog are analyzed. Results show that the robot can traverse Martian soil surface analog with maximum forward speed 28.13 m s-1turning speed 1.94° s-1and obstacle height 74.85 mm. The maximum angle for climbing Martian soil slope analog is 28°, corresponding slippery rate 76.8%. It is predicted that this robot can adapt to Martian granular rough terrain with gentle slopes.

Interleg coordination in free-walking bug Erthesina fullo (Hemiptera: Pentatomidae).

Insects can adapt their walking patterns to complex and varied environments and retain the ability to walk even after significant changes in their physical attributes, such as amputation. Although the interleg coordination of intact insects has been widely described in previous studies, the adaptive walking patterns in free-walking insects with amputation of 1 or more legs are still unclear. The pentatomid bug Erthesina fullo exhibits a tripod gait, when walking freely on horizontal substrates, like many other insects. In this study, amputations were performed on this species to investigate changes in interleg coordination. The walking parameters were analyzed, such as the locations of touchdown and liftoff, cycle period, walking speed, and head displacement of intact and amputated insects. The results show that E. fullo displays adaptive interleg coordination in response to amputations. With 1 amputated leg, bugs changed to a 3-unit gait, whereas with 2 amputated legs they employed a wave gait. These data are helpful in exploring the motion mode control in walking insects and provide the theoretical basis for the gait control strategy of robots, when leg failure occurs.

Design of composite puncture blood collection system and research on puncture force.

Venous blood collection testing is one of the most commonly used medical diagnostic methods. Compared with conventional venous blood collection, robotic collection can reduce needle-stick injuries, medical staff workload, and infection risk; allow doctor-patient isolation; and improve collection reliability. Existing venous blood collection robots use rigid puncture needles, which can easily puncture the lower wall of blood vessels, causing vessel damage and collection failure. This paper proposes a bionic blood collection strategy based on a composite puncture needle that mimics the structure and function of mosquito mouthparts. A bionic composite puncture needle insertion system with puncture-force sensing was designed, and venipuncture forces were simulated and mathematically modelled. A prototype insertion system was built and used in an experiment, which demonstrated effective composite puncture blood collection and explored the factors influencing puncture force. Puncture force decreases with increased puncture speed and angle and with a decreased needle diameter. This provides a basis for optimising the parameters of blood collection robots.

Development of a Lizard-Inspired Robot for Mars Surface Exploration.

Exploring Mars is beneficial to increasing our knowledge, understanding the possibility of ancient microbial life there, and discovering new resources beyond the Earth to prepare for future human missions to Mars. To assist ambitious uncrewed missions to Mars, specific types of planetary rovers have been developed for performing tasks on Mars' surface. Due to the fact that the surface is composed of granular soils and rocks of various sizes, contemporary rovers can have difficulties in moving on soft soils and climbing over rocks. To overcome such difficulties, this research develops a quadruped creeping robot inspired by the locomotion characteristics of the desert lizard. This biomimetic robot features a flexible spine, which allows swinging movements during locomotion. The leg structure utilizes a four-linkage mechanism, which ensures a steady lifting motion. The foot consists of an active ankle and a round pad with four flexible toes that are effective in grasping soils and rocks. To determine robot motions, kinematic models relating to foot, leg, and spine are established. Moreover, the coordinated motions between the trunk spine and leg are numerically verified. In addition, the mobility on granular soils and rocky surface are experimentally demonstrated, which can imply that this biomimetic robot is suitable for Mars surface terrains.

Rate-dependent adhesion together with limb collaborations facilitate grasshoppers reliable attachment under highly dynamic conditions.

Dynamic attachment is indispensable for animals to cope with unexpected disturbances. Minor attention has been paid to the dynamic performance of insects' adhesive pads. Through experiments pulling whole grasshoppers off a glass rod at varying speeds, surprising findings emerged. The feet did not always maintain contact but released and then reconnected to the substrate rapidly during leg extension, potentially reducing the shock damage to pads. As the pulling speeds increased from 1 to 400 mm/s, the maximum forces of single front tarsus insects and entire tarsi insects were nearly proportional to the 1/3 power of pulling speeds by 0.11 and 0.29 times, respectively. The force of some individuals could be even 800 times greater than their weight, which is unexpectedly high for smooth insect pads. This work not only helps us to understand the attachment intelligence of animals but is also informative for artificial attachment in extreme situations.

A rehabilitation robot control framework with adaptation of training tasks and robotic assistance.

Robot-assisted rehabilitation has exhibited great potential to enhance the motor function of physically and neurologically impaired patients. State-of-the-art control strategies usually allow the rehabilitation robot to track the training task trajectory along with the impaired limb, and the robotic motion can be regulated through physical human-robot interaction for comfortable support and appropriate assistance level. However, it is hardly possible, especially for patients with severe motor disabilities, to continuously exert force to guide the robot to complete the prescribed training task. Conversely, reduced task difficulty cannot facilitate stimulating patients' potential movement capabilities. Moreover, challenging more difficult tasks with minimal robotic assistance is usually ignored when subjects show improved performance. In this paper, a control framework is proposed to simultaneously adjust both the training task and robotic assistance according to the subjects' performance, which can be estimated from the users' electromyography signals. Concretely, a trajectory deformation algorithm is developed to generate smooth and compliant task motion while responding to pHRI. An assist-as-needed (ANN) controller along with a feedback gain modification algorithm is designed to promote patients' active participation according to individual performance variance on completing the training task. The proposed control framework is validated using a lower extremity rehabilitation robot through experiments. The experimental results demonstrate that the control scheme can optimize the robotic assistance to complete the subject-adaptation training task with high efficiency.

A Gecko-Inspired Robot with a Flexible Spine Driven by Shape Memory Alloy Springs.

The majority of sprawling-posture quadrupedal vertebrates, such as geckos and lizards, adopt a cyclical lateral swing pattern of their trunk that is coordinated with limb movements to provide extraordinary flexibility and mobility. Inspired by the gecko's locomotory gait and posture, a gecko-like robot with a flexible spine driven by shape memory alloy (SMA) springs was proposed in this work. The static parameters of the SMA spring were experimentally measured, and the flexible spine driven by SMA springs can be deflected bidirectionally. A kinematic model of the spine mechanism was established, and the mathematical relationship between the thermodynamic behavior of the SMA springs and spinal deflection was systematically analyzed. When a gecko trots with a lateral swing pattern of its trunk, the body and the spine show a standing wave shape and a single-peak C-type curve, respectively. The lateral spine deflection and trotting gait were combined in a collaborative model of a flexible spine and limbs to describe in detail the specific relationships between leg joint variables and spine deflection angle. Planar motion tests of a prototype robot were also conducted by using four high-speed cameras to record the trajectory of each point of the body, which verified the proposed model. From the acquired results, it was demonstrated that, compared with a rigid body, a robot with a flexible spine has a longer stride length, higher speed, and a greatly reduced turning radius.

An Aerial-Wall Robotic Insect That Can Land, Climb, and Take Off from Vertical Surfaces.

Insects that can perform flapping-wing flight, climb on a wall, and switch smoothly between the 2 locomotion regimes provide us with excellent biomimetic models. However, very few biomimetic robots can perform complex locomotion tasks that combine the 2 abilities of climbing and flying. Here, we describe an aerial-wall amphibious robot that is self-contained for flying and climbing, and that can seamlessly move between the air and wall. It adopts a flapping/rotor hybrid power layout, which realizes not only efficient and controllable flight in the air but also attachment to, and climbing on, the vertical wall through a synergistic combination of the aerodynamic negative pressure adsorption of the rotor power and a climbing mechanism with bionic adhesion performance. On the basis of the attachment mechanism of insect foot pads, the prepared biomimetic adhesive materials of the robot can be applied to various types of wall surfaces to achieve stable climbing. The longitudinal axis layout design of the rotor dynamics and control strategy realize a unique cross-domain movement during the flying-climbing transition, which has important implications in understanding the takeoff and landing of insects. Moreover, it enables the robot to cross the air-wall boundary in 0.4 s (landing), and cross the wall-air boundary in 0.7 s (taking off). The aerial-wall amphibious robot expands the working space of traditional flying and climbing robots, which can pave the way for future robots that can perform autonomous visual monitoring, human search and rescue, and tracking tasks in complex air-wall environments.

The forewing of a black cicada Cryptotympana atrata (Hemiptera, Homoptera: Cicadidae): Microscopic structures and mechanical properties.

Insects in nature flap their wings to generate lift force and driving torque to adjust their attitude and control stability. An insect wing is a biomaterial composed of flexible membranes and tough veins. In this paper, we study the microscopic structures and mechanical properties of the forewing of the black cicada, Cryptotympana atrata. The thickness of the wing membranes and the diameter of veins varied from the wing root to the tip. The thickness of the wing membranes ranged from 6.0 to 29.9 µm, and the diameter of the wing veins decreased in a gradient from the wing root to the tip, demonstrating that the forewing of the black cicada is a nonuniform biomaterial. The elastic modulus of the membrane near the wing root ranged from 4.45 to 5.03 GPa, which is comparable to that of some industrial membranes. The microstructure of the wing vein exhibited a hollow tubular structure with flocculent structure inside. The "fresh" sample stored more water than the "dry" sample, resulting in a significant difference in the elastic modulus between the fresh and dried veins. The different membrane thicknesses and elastic moduli of the wing veins near the root and tip resulted in varied degrees of deformation on both sides of the flexion line of the forewing during twisting. The measurements of the forewing of the cicada may serve as a guide for selecting airfoil materials for the bionic flapping-wing aircraft and promote the design and manufacture of more durable bionic wings in the future. RESEARCH HIGHLIGHTS: The distribution of the wing vein diameter and the wing membrane thickness indicated that the forewing of Cryptotympana atrata is composed of heterogeneous materials. The wing membrane and the outer wall of the wing vein are the layered structure with multilayer fibers, which has a great significance for improving the ability of the forewing to sustain aerodynamic loads. The elastic modulus of the wing membrane near the wing root is in the range of 4.45-5.03 GPa, which is comparable to that of membranes manufactured by industries. This is a suitable reference for selecting materials for making bionic aircraft wings. We proved that the elastic moduli of the "fresh" and "dry" wing veins differ greatly compared with those of the wing membrane. Because the wing vein microstructure exhibits an internal hollow tubular structure with flocculent structure inside, the "fresh" sample stores more water than the "dry" sample. The wing membrane near the wing root is thicker and reinforced by the main wing vein with a high elastic modulus. This renders the region near the wing root difficult to deform. The membrane far from the wing root is thinner and the elastic modulus of the nearby wing veins is smaller, making them more flexible.

Design of a Variable Stiffness Gecko-Inspired Foot and Adhesion Performance Test on Flexible Surface.

Adhesion robots have broad application prospects in the field of spacecraft inspection, repair, and maintenance, but the stable adhesion and climbing on the flexible surface covering the spacecraft has not been achieved. The flexible surface is easily deformed when subjected to external force, which makes it difficult to ensure a sufficient contact area and then detach from it. To achieve stable attachment and easy detachment on the flexible surface under microgravity, an adhesion model is established based on the applied adhesive material, and the relationship between peeling force and the rigidity of the base material, peeling angle, and working surface stiffness is obtained. Combined with the characteristics of variable stiffness structure, the adhesion and detachment force of the foot is asymmetric. Inspired by the adhesion-detachment mechanism of the foot of the gecko, an active adhesion-detachment control compliant mechanism is designed to achieve the stable attachment and safe detachment of the foot on the flexible surface and to adapt to surfaces with different rigidity. The experimental results indicate that a maximum normal adhesion force of 7.66 N can be generated when fully extended, and the safe detachment is achieved without external force on a flexible surface. Finally, an air floating platform is used to build a microgravity environment, and the crawling experiment of a gecko-inspired robot on a flexible surface under microgravity is completed. The experimental results show that the gecko-inspired foot with variable stiffness can satisfy the requirements of stable crawling on flexible surfaces.

A gecko-inspired robot with CPG-based neural control for locomotion and body height adaptation.

Today's gecko-inspired robots have shown the ability of omnidirectional climbing on slopes with a low centre of mass. However, such an ability cannot efficiently cope with bumpy terrains or terrains with obstacles. In this study, we developed a gecko-inspired robot (Nyxbot) with an adaptable body height to overcome this limitation. Based on an analysis of the skeletal system and kinematics of real geckos, the adhesive mechanism and leg structure design of the robot were designed to endow it with adhesion and adjustable body height capabilities. Neural control with exteroceptive sensory feedback is utilised to realise body height adaptability while climbing on a slope. The locomotion performance and body adaptability of the robot were tested by conducting slope climbing and obstacle crossing experiments. The gecko robot can climb a 30° slope with spontaneous obstacle crossing (maximum obstacle height of 38% of the body height) and can climb even steeper slopes (up to 60°) without an obstacle or bump. Using 3D force measuring platforms for ground reaction force analysis of geckos and the robot, we show that the motions of the developed robot driven by neural control and the motions of geckos are dynamically comparable. To this end, this study provides a basis for developing climbing robots with adaptive bump/obstacle crossing on slopes towards more agile and versatile gecko-like locomotion.