RESUMO
Herein, an integrated structure of single Fe atom doped core-shell carbon nanoboxes wrapped by self-growing carbon nanotubes (CNTs) is designed. Within the nanoboxes, the single Fe atom doped hollow cores are bonded to the shells via the carbon needles, which act as the highways for the electron transport between cores and shells. Moreover, the single Fe atom doped nanobox shells is further wrapped and connected by self-growing carbon nanotubes. Simultaneously, the needles and carbon nanotubes act as the highways for electron transport, which can improve the overall electron conductivity and electron density within the nanoboxes. Finite element analysis verifies the unique structure including both internal and external connections realize the integration of active sites in nano scale, and results in significant increase in electron transfer and the catalytic performance of Fe-N4 sites in both Li2 Sn lithiation and Li2 S delithiation. The Li-S batteries with the double-shelled single atom catalyst delivered the specific capacity of 702.2 mAh g-1 after 550 cycles at 1.0 C. The regional structure design and evaluation method provide a new strategy for the further development of single atom catalysts for more electrochemical processes.
RESUMO
The key to realizing practical applications of Li-S batteries lies in scalable fabrication of cathode materials with high sulfur-loading and strong binding of lithium polysulfides (LiPSs). We report a scalable CeO2-CNT@C porous membrane with a large porosity of 90%. Introducing CNTs is critical to increase the porosity and construct porous networks with CNTs as the skeleton and CeO2-doped carbon as the shell. The macropores can improve the transport of Li+ and electrolyte, while the porous networks possess high polysulfide-adsorbing and electron-transferring ability. The CeO2-CNT@C membrane can serve as an Al foil-free cathode and an interlayer for Li-S batteries. Moreover, CeO2 can immobilize LiPSs and can alleviate its shuttle effect. The Li-S batteries with a sulfur loading of 6.2 mg cm-2 deliver a capacity of 847 mA h g-1 after 100 cycles, showing a high areal capacity of 5.25 mA h cm-2 at a low electrolyte/sulfur ratio of 5.2 µL mg-1.
RESUMO
With the rapid growth of material innovations, multishelled hollow nanostructures are of tremendous interest due to their unique structural features and attractive physicochemical properties. Continued effort has been made in the geometric manipulation, composition complexity, and construction diversity of this material, expanding its applications. Energy storage technology has benefited from the large surface area, short transport path, and excellent buffering ability of the nanostructures. In this work, the general synthesis of multishelled hollow structures, especially with architecture versatility, is summarized. A wealth of attractive properties is also discussed for a wide area of potential applications based on energy storage systems, including Li-ion/Na-ion batteries, supercapacitors, and Li-S batteries. Finally, the emerging challenges and outlook for multishelled hollow structures are mentioned.
RESUMO
BACKGROUND: Glioblastomas have a high degree of malignancy, high recurrence rate, high mortality rate, and low cure rate. Searching for new markers of glioblastomas is of great significance for improving the diagnosis, prognosis and treatment of glioma. METHODS: Using the GEO public database, we combined 34 glioma microarray datasets containing 1893 glioma samples and conducted genetic data mining through statistical analysis, bioclustering, and pathway analysis. The results were validated in TCGA, CGGA, and internal cohorts. We further selected a gene for subsequent experiments and conducted cell proliferation and cell cycle analyses to verify the biological function of this gene. RESULTS: Eight glioblastoma-specific differentially expressed genes were screened using GEO. In the TCGA and CGGA cohorts, patients with high CBX3, BARD1, EGFR, or IFRD1 expression had significantly shorter survival but patients with high GUCY1A3 or MOBP expression had significantly longer survival than patients with lower expression of these genes. After reviewing the literature, we selected the CBX3 gene for further experiments. We confirmed that CBX3 was overexpressed in glioblastoma by immunohistochemical analysis of tissue microarrays and qPCR analysis of surgical specimens. The functional assay results showed that silencing CBX3 arrests the cell cycle in the G2/M phase, thereby weakening the cell proliferation ability. CONCLUSIONS: We used a multidisciplinary approach to analyze glioblastoma samples in 34 microarray datasets, revealing novel diagnostic and prognostic biomarkers in patients with glioblastoma and providing a new direction for screening tumor markers.
Assuntos
Biomarcadores Tumorais/análise , Neoplasias Encefálicas/diagnóstico , Biologia Computacional/métodos , Conjuntos de Dados como Assunto , Glioblastoma/diagnóstico , Análise em Microsséries , Biomarcadores Tumorais/genética , Biomarcadores Tumorais/isolamento & purificação , Neoplasias Encefálicas/genética , Neoplasias Encefálicas/mortalidade , Neoplasias Encefálicas/patologia , Estudos de Casos e Controles , Linhagem Celular Tumoral , Bases de Dados Genéticas , Perfilação da Expressão Gênica/métodos , Regulação Neoplásica da Expressão Gênica , Glioblastoma/genética , Glioblastoma/mortalidade , Glioblastoma/patologia , Humanos , Análise em Microsséries/métodos , Análise em Microsséries/estatística & dados numéricos , Prognóstico , Análise de Sobrevida , Integração de Sistemas , Análise Serial de TecidosRESUMO
Accurate diagnosis of pathogenic Nosema spp. in Antheraea pernyi samples is considered especially useful for reducing economic losses in sericulture and improving food safety by maintaining pathogen-free pupae. However, microscopy and immunologic methods have poor diagnostic sensitivity, while the more sensitive PCR methods remain costly and time-consuming for template preparation. To address this issue, we introduce a sensitive ALMS-qPCR method that combines fast, simple DNA extraction using Alkali Lysis followed by Magnetic bead Separation (ALMS) and quantitative real-time PCR (qPCR). This approach is especially fit for large-scale pathogen molecular screening, because the DNA preparation procedure is fast (<0.94â¯min per sample) and is high-throughput (performs on a 96-well plate). It is cost-effective, since the most expensive materials can be made in the lab and can be recycled, while the automated procedure can help to minimize labor cost. Though the DNA preparation procedure was substantially simplified, common PCR inhibitory factors were not observed. The sensitivity of ALMS-qPCR is high and the limit of detection is 0.045â¯parasites/µL. Large-scale screening of Nosema spp. in 3000 Antheraea pernyi samples confirmed the efficacy of the ALMS-qPCR method. Sensitivity is much higher than clinical microscopy, especially for host groups with low infection prevalence and levels. High-throughput ALMS-qPCR, combining automated DNA preparation and sensitive qPCR, provides an enhanced approach for pébrine screening and epidemiological studies. The application of ALMS-qPCR in the sericulture industry will help to strengthen pébrine control and breed pathogen-free species, which means much safer food provision and better genetic resource conservation.
Assuntos
Microsporidiose/diagnóstico , Mariposas/microbiologia , Nosema/isolamento & purificação , Animais , Patologia Molecular/métodos , Reação em Cadeia da Polimerase em Tempo Real/métodosRESUMO
Active pharmaceutical ingredients (APIs) crystal preparation is a significant issue for the pharmaceutical development attributed to the effect on anti-inflammatory, anti-bacteria, and anti-viral, etc. While, the massive preparation of API crystal with high polymorphism selectivity is still a pendent challenge. Here, we firstly proposed a criterion according to the molecular aggregation, molecular orientation, and hydrogen bond energy between INA molecules from molecular dynamics (MD) simulations, which predicted the hydrogen bond architecture in crystal under different electric fields, hinting the recognition of crystal polymorphism. Then, an electric field governing confined liquid crystallization was constructed to achieve the INA crystal polymorphism screening relying on the criterion. Further, magnifying confined liquid volume by 5000 times from 1.0 µL to 5.0 mL realized the massive preparation of INA crystal with high polymorphic purity (>98.4%), giving a unique pathway for crystal engineering and pharmaceutical industry on the development of innovative and generic API based drugs.
RESUMO
A recent study based on gonad histology revealed that the existence of the spawning grounds for Gray's grenadier anchovy (Coilia grayii) and Osbeck's grenadier anchovy (C. mystus) in the Min River Estuary, the largest in Fujian Province, southern China. Further confirming their natal sources and migratory patterns is essential to understand their life histories. We used otolith microchemistry to assess the origins and habitat uses of 23 C. grayii and 22 C. mystus, collected the Min River Estuary and the adjacent waters. The results showed that C. grayii spawned in both freshwater (n| = 14) and brackish water (n = 9), and C. mystus spawned mainly in brackish water (n| = 20) with minor in freshwater (n| = 1) and marine water (n| = 1). The migratory patterns of C. grayii (four types) and C. mystus (five types) were diverse, mainly exhibiting anadromous and semi-anadromous behaviors. The first migratory behavior of C. grayii and C. mystus occurred within the age of the first year. The findings have significant implications for fishery stock management of the Min River Estuary and its adjacent waters.
Assuntos
Membrana dos Otólitos , Rios , Animais , Estuários , Microquímica , Peixes , ChinaRESUMO
INTRODUCTION: Suboptimal medication adherence is common among patients with cardiovascular diseases. We sought evidence on non-pharmacological interventions used to support adherence for patients with hypertension and/or dyslipidemia. METHODS: We searched MEDLINE, EMBASE, MEDLINE In-Process, ClinicalTrials.gov, EUCTR, and conference proceedings from July 2011 to July 2021 to identify trials evaluating effects of health education, phone reminders, or digital interventions on medication adherence or persistence of adult patients with hypertension and/or dyslipidemia. Risk of bias was assessed using the Cochrane Risk of Bias Assessment Tool v2. RESULTS: Of 64 studies, 62 used health education approaches (e.g. educational interviews, motivational meetings, advice from physicians, and mobile health content), 16 phone reminders (e.g. text reminders, electronic pill-box linked reminders, bi-directional text messaging), and 10 digital applications as interventions (e.g., various self-management applications). All studies assessed medication adherence; only two persistence. Overall, 30 studies (83%) assessing health education approaches alone and 25 (78%) combined with other strategies, 12 (75%) phone reminders and eight studies (80%) digital applications combined with other strategies reported improved medication adherence. Two studies assessing health education approaches reported improved persistence. CONCLUSIONS: Our findings indicate non-pharmacological interventions may positively impact adherence. Therefore, 'beyond the pill' approaches could play a role in preventing cardiovascular diseases.
RESUMO
Gout flare-up, commonly resulting from monosodium urate monohydrate (MSUM) crystallization, has led to painful inflammatory arthritis among hundreds of millions of people. Herein, a kind of hydrogel nanoparticles (HNPs) with specific properties was developed, aimed at providing a promising pathway for MSUM crystallization control. The experimental and molecular dynamics simulation results synchronously indicate that the fabricated HNPs achieve efficient inhibition of MSUM crystallization governed by the mechanism of "host-guest interaction" even under very low-dose administration. HNPs as the host dispersed in the hyperuricemic model effectively lift the relative heterogeneous nucleation barrier of the MSUM crystal and hinder solute aggregation with strong electronegativity and hydrophobicity. The initial appearance of MSUM crystals was then delayed from 94 to 334 h. HNPs as the guest on the surface of the formed crystal can decelerate the growth rate by anchoring ions and occupying the active sites on the surface, and the terminal yield of the MSUM crystal declined to less than 1% of the control group. The good biocompatibility of HNPs (cell viability > 94%) renders it possible for future clinical applications. This study can guide the rational design of inhibitory nanomaterials and the development of their application in the control of relevant pathological crystallization.
Assuntos
Cristalização , Hidrogéis , Simulação de Dinâmica Molecular , Nanopartículas , Ácido Úrico , Ácido Úrico/química , Hidrogéis/química , Nanopartículas/química , Animais , Sobrevivência Celular/efeitos dos fármacos , Camundongos , Tamanho da Partícula , Íons/química , Propriedades de SuperfícieRESUMO
Antisolvent engineering is routinely used to modulate the crystallization of perovskite films as they can offer an additional driving force for nucleation. Actually, the intervention of antisolvent into nucleation is thought to involve some relatively fast and complex processes, which, however, are not fully understood so far. Here, the diffusion of the organic amine cation FA+ (one dominated precursor) and its distribution in a spin-coating process in different antisolvents is simulated by the computational fluid dynamics (CFD) model. It is suggested that a moderate diffusion rate (like that in the case of toluene as an antisolvent) not only enables to form a very uniform distribution of FA+ ions on the substrate, beneficial to the uniform nucleation of the intermediate phase, but also can balance the nucleation and growth rates of the intermediate phase, thereby suppressing undesired heterogeneous nucleation and growth. Results show that the perovskite film fabricated using toluene as an antisolvent has a high quality, based on which higher power conversion efficiencies of up to 24.32% are achieved for perovskite solar cells.
RESUMO
Two-dimensional (2D) nanomaterials, due to their high aspect ratio and high specific surface area, which provide a more tortuous pathway for larger gas molecules, are frequently used in membrane separation. However, in mixed-matrix membranes (MMMs), the high aspect ratio and high specific surface area of 2D fillers can increase transport resistance, thereby reducing the permeability of gas molecules. In this work, we combine boron nitride nanosheets (BNNS) with ZIF-8 nanoparticles to develop a novel material, ZIF-8@BNNS, to improve both CO2 permeability and CO2/N2 selectivity. Growth of ZIF-8 nanoparticles on the BNNS surface is achieved using an in-situ growth method where the amino groups of BNNS are complexed with Zn2+, creating gas transmission pathways that accelerate CO2 transmission. The 2D-BNNS material acts as a barrier in MMMs to improve CO2/N2 selectivity. The MMMs with a 20 wt.% ZIF-8@BNNS loading achieved a CO2 permeability of 106.5 Barrer and CO2/N2 selectivity of 83.2, surpassing the Robeson upper bound (2008) and demonstrating that MOF layers can efficiently reduce mass transfer resistance and enhance gas separation performance.
RESUMO
Due to the low boiling point of helium, the nitrogen-rich off gas of the nitrogen rejection unit (NRU) in the liquefied natural gas (LNG) plant usually contains a small amount of CH4, approximately 1-4% He, and associated gases, such as H2. However, it is difficult to separate hydrogen and helium. Here, we propose two different integrated processes coupled with membrane separation, pressure swing adsorption (PSA), and the electrochemical hydrogen pump (EHP) based on different sequences of hydrogen gas removal. Both processes use membrane separation and PSA in order to recover and purify helium, and the EHP is used to remove hydrogen. The processes were strictly simulated using UniSim Design, and an economic assessment was conducted. The results of the economic assessment show that flowsheet #2 was more cost-effective due to the significant reduction in the capacity of the compressor and PSA because of the pre-removal of hydrogen. Additionally, using the response surface methodology (RSM), a Box-Behnken design experiment was conducted, and an accurate and reliable quadratic response surface regression model was fitted through variance analysis. The optimized operating parameters for the integrated process were determined as follows: the membrane area of M101 was 966.6 m2, the permeate pressure of M101 was 100 kPa, and the membrane area of M102 was 41.2 m2. The maximum recovery fraction was 90.66%, and the minimum cost of helium production was 2.21 $/kg. Thus, proposed flowsheet #2 has prospects and value for industrial application.
RESUMO
BACKGROUND: Extraintestinal Pathogenic Escherichia coli (ExPEC) is a leading cause of invasive disease, including bacteremia and sepsis. Invasive ExPEC disease (IED) has the potential to complicate the clinical treatment of other conditions and is associated with an increased mortality, hospitalization, and worse outcomes. Older adults and individuals with comorbid conditions are at higher risk of IED. ExPEC is of particular concern in the Asia Pacific region due to aging populations and rising antimicrobial resistance. OBJECTIVES: This study aimed to synthesize most recent data on the epidemiology, clinical and economic burden of IED in the elderly/high risk populations in China, Japan, South Korea, Taiwan, and Australia. METHODS: A targeted literature review was conducted using Embase, Medline, as well as local scientific databases. We included studies published in English and local languages published from January 1, 2010 to October 7, 2020 that were relevant to the research objectives. Studies were narratively synthesized. RESULTS: A total of 1,047 studies were identified and 34 of them were included in this review. ExPEC accounted for 46.0% (1,238/2,692) of bacteria-related invasive diseases in patients aged above 60 years in South Korea, followed by China (44.4% (284/640)), Taiwan (39.0% (1,244/3,194)), and Japan (18.1% (581/3,206)), while Australia reported ExPEC out of all pathogens (54.7% (4,006/7,330)) in general adults. Comorbidities such as diabetes or cancer were common in these patients. Studies reported increases in length-of-stay, and in-hospital 30-day all-cause mortality related to ExPEC associated bacteremia was between 9% to 12%. From a cost perspective, a 3-fold increase in sepsis-associated cost was reported in South Korea between 2005 and 2012. In Australia, antimicrobial resistance contributed to an additional cost of AUD $5.8 million per year (95% uncertainty interval [UI], $2.2-$11.2 million) in the treatment of bloodstream infections (BSIs). CONCLUSION: ExPEC was a major cause of blood stream infection across China, Japan, South Korea, Taiwan, and Australia. Both the clinical and economic burden associated to ExPEC infections as well as the antimicrobial resistance observed in the elderly call for preventive and curative actions in these regions.
Extraintestinal Pathogenic Escherichia coli (ExPEC) is a leading cause of invasive disease, including bacteremia and sepsis.A targeted literature review included the most recent data from 34 published studies on the epidemiology and clinical and economic burden of IED in the elderly/high risk populations in China, Japan, South Korea, Taiwan, and Australia.ExPEC accounted for 46.0% (1,238/2,692) of bacteria-related invasive diseases in patients aged above 60 years in South Korea, followed by China (44.4% (284/640)), Taiwan (39.0% (1,244/3,194)), and Japan (18.1% (581/3,206)), while Australia reported ExPEC out of all pathogens (54.7% (4,006/7,330)) in general adults. Studies reported increases in length-of-stay and in-hospital 30-day all-cause between 9% to 12%. These factors, along with antimicrobial resistance observed in the elderly, call for preventive and curative actions in these regions.Data for costs associated with ExPEC induced BSI or sepsis in this region are limited, but evidence shows increasing expenditures.
Assuntos
Anti-Infecciosos , Bacteriemia , Infecções por Escherichia coli , Escherichia coli Extraintestinal Patogênica , Sepse , Humanos , Idoso , Escherichia coli , Infecções por Escherichia coli/tratamento farmacológico , Infecções por Escherichia coli/epidemiologia , Ásia , Sepse/epidemiologia , Bacteriemia/tratamento farmacológico , Bacteriemia/epidemiologiaRESUMO
Droplet crystallization behavior held great potential in crystal preparation, micromaterial engineering, and molecular assembly. However, restricted by natural surface tension, the intrinsic crystallization regulation and efficient harvest of high quality crystal in diverse droplet features were still a great challenge. Herein, we developed a 3D printed semiflexible micro crystallizer with two aspectant sessile platforms that could simultaneously construct a series of heteromorphic droplets (HDs) and controllable HD shape. By shaping HD on the interface of the platform, central-converging micro-flows were generated by coordinating the gas-liquid interface and flow intensity (i.e., Ra/Ma) during HD crystallization from 'barrel', 'can', to 'sand clock' shape, which was validated via simulative and experimental research. Therefore, HDs, constructed in semiflexible micro crystallizer, exhibited efficient screening (>70 %) of single cubic crystal just at the center zone of platform, even under wide ranges of concentration and volume, manifesting excellent repeatability on high quality crystal harvest and relevant interfacial science research.
Assuntos
Cristalização , Impressão TridimensionalRESUMO
Nanofiltration application for the separation of Mg2+-Li+ from salt-lake brines was attempted in the present work. Four different nanofiltration membranes identified in the manuscript as DL, DK, NF-270, and NF-90 were used to treat salt brine with a magnesium to lithium ratio (MLR) of 61, additionally contaminated by the other ions such as Na+, K+, Ca2+, etc. The effect of the dilution factor, operating pressure, circulation rate, and feed pH were assessed to identify the optimal operating conditions for each membrane based on the retention efficiency of each ion. The results showed an insignificant effect of Ca2+ on the retention performance of Mg2+-Li+. Na+ and K+ had a smaller hydration radius and larger diffusion coefficient, which competed with Li+ and altered the separation of Mg2+-Li+. Under the optimal conditions (dilution factor: 40; operating pressure: 1.2 MPa; circulation flow rate: 500 L/h; pH: 7), the retention efficiency of lithium was as low as 5.17%, separation factor (SF) was as low as 0.074, and the MLR in the permeate reduced to 0.088.
RESUMO
Mixed matrix membranes (MMMs) generally have some fatal defects, such as poor compatibility between the two phases leading to non-selective pores. In this work, PIM-1 was chosen as the polymer matrix, and UiO-66 modified with amidoxime (UiO-66-AO) was used as the filler to prepare the MMMs. In the MMMs, the amino and hydroxyl groups on UO-66-AO form a rich hydrogen bond network with the N and O atoms in the polymer PIM-1 chain to improve the compatibility between the polymer matrix and the filler. In addition, the selective adsorption of CO2 by the amidoxime group can promote the transport of CO2 in the membrane, which enhances the gas selectivity. The CO2 permeability and CO2/N2 selectivity of UiO-66-AO@PIM-1 MMMs are increased by 35.2% and 45.2% compared to pure PIM-1 membranes, reaching 7535.5 Barrer and 26.9, surpassing the Robeson Upper Bound (2008) and close to the 2019 Upper Bound. After 38 days of the aging experiment, the CO2 permeability is approximately 74% of the original. The results show that the addition of UiO-66-AO has an obvious effect on improving the aging properties of the membrane. The UiO-66-AO@PIM-1 MMMs have a bright prospect for CO2 separation in the future.
RESUMO
Membrane distillation (MD) has prominent advantages such as treating high-salinity wastewater with a low-grade thermal energy, high salt rejection, and zero discharge. However, organic fouling and mineral scaling are two major challenges for hydrophobic MD membranes when used for practical applications. Commonly, improving organic fouling- and mineral scaling-resistance require oppositely enhanced wetting properties of membrane, thus is difficult to simultaneously realize dual resistance with one membrane. Here, we proposed to use underwater thermodynamically stable high-surface-energy coating to modify the hydrophobic membrane with Janus structures comprising different surface energy. The underlayered structure meets the hydrophobicity requirements of the MD membrane, while the coating layer realizes dual resistance to organic and inorganic foulants. Theoretical analysis and experimental proof reveal that the membrane with the high-surface-energy coating layer outperforms the pristine one with approximately 10 times of longevity. This strategy provides a new way for the use of high-surface-energy materials in versatilely fouling-resistant MD process.
Assuntos
Incrustação Biológica , Purificação da Água , Destilação , Incrustação Biológica/prevenção & controle , Membranas Artificiais , Água do Mar , MineraisRESUMO
Herein, a facile bionic research platform with fabricated hydrogel composite membrane (HCM) is constructed to uncover the effects of the main components of coffee's metabolites on MSUM crystallization. Tailored and biosafety polyethylene glycol diacrylate/N-isopropyl acrylamide (PEGDA/NIPAM) HCM allows the proper mass transfer of coffee's metabolites and can well simulate the process of coffee's metabolites acting in the joint system. With the validations of this platform, it is shown that chlorogenic acid (CGA) can hinder the MSUM crystals formation from 45 h (control group) to 122 h (2 mM CGA), which is the most likely reason that reduces the risk of gout after long-term coffee consumption. Molecular dynamics simulation further indicates that the high interaction energy (Eint) between CGA and MSUM crystal surface and the high electronegativity of CGA both contribute to the restraint of MSUM crystal formation. In conclusion, the fabricated HCM, as the core functional materials of the research platform, presents the understanding of the interaction between coffee consumption and gout control.
Assuntos
Gota , Ácido Úrico , Humanos , Ácido Úrico/química , Café , Hidrogéis , Cristalização , Gota/metabolismoRESUMO
Functional interfaces and devices for rapid adsorption and immobilization of nucleic acids (NAs) are significant for relevant bioengineering applications. Herein, a microdevice with poly(acrylic acid) (PAA) photosensitive resin was integrated by three-dimensional (3D) printing, named DPAA for short. Precise microscale structures and abundant surface carboxyl functional groups were fabricated for fast and high-throughput deoxyribonucleic acid (DNA) separation. Surface modification was then done using polydopamine (PDA) and poly(ethylene glycol) (PEG) to obtain modified poly(acrylic acid) (PAA)-based devices DPDA-PAA and DPEG-PAA rich in amino and hydroxyl groups, respectively. The fabricated device DPAA possessed superior printing accuracy (40-50 µm). Functionalization of amino and hydroxyl was successful, and the modified devices DPDA-PAA and DPEG-PAA maintained a high thermal stability like DPAA. Surface potential analysis and molecular dynamics simulation indicated that the affinity for DNA was in the order of DPDA-PAA > DPEG-PAA > DPAA. Further DNA separation experiments confirmed the high throughput and high selectivity of DNA separation performance, consistent with the predicted affinity results. DPDA-PAA showed relatively the highest DNA extraction yield, while DPEG-PAA was the worst. An acidic binding system is more favorable for DNA separation and recovery. DPDA-PAA showed significantly better DNA extraction performance than DPAA in a weakly acidic environment (pH 5.0-7.0), and the average DNA yield of the first elution was 2.16 times that of DPAA. This work validates the possibility of modification on integrated 3D microdevices to improve their DNA separation efficiency effectively. It also provides a new direction for the rational design and functionalization of bioengineering separators based on nonmagnetic methods. It may pave a new path for the highly efficient polymerase chain reaction diagnosis.
Assuntos
Ácidos Nucleicos , Polietilenoglicóis , Polietilenoglicóis/química , DNARESUMO
INTRODUCTION: The burden of respiratory syncytial virus (RSV), which causes acute respiratory illness, is well recognized among the pediatric population but also imposes a significant risk to the elderly (age ≥ 60) and those with underlying comorbidities. The study aimed to review the most recent data on epidemiology and burden (clinical and economic) of RSV in the elderly/high-risk populations in China, Japan, South Korea, Taiwan, and Australia. METHODS: A targeted review was conducted of English, Japanese, Korean, and Chinese language articles published from 1 January 2010 to 7 October 2020 relevant for the purpose. RESULTS: A total of 881 studies were identified, and 41 were included. The median proportion of elderly patients with RSV in all adult patients with acute respiratory infection (ARI) or community acquired pneumonia was 79.78% (71.43-88.12%) in Japan, 48.00% (3.64-80.00%) in China, 41.67% (33.33-50.00%) in Taiwan, 38.61% in Australia, and 28.57% (22.76-33.33%) in South Korea. RSV was associated with a high clinical burden on those patients with comorbidities such as asthma and chronic obstructive pulmonary disease. In China, inpatients with ARI showed a significantly higher rate of RSV-related hospitalization than outpatients (13.22% versus 4.08%, p < 0.01). The median length of hospital stay among elderly patients with RSV was longest in Japan (30 days) and shortest in China (7 days). Mortality data varied by region with some studies reporting rates as high as 12.00% (9/75) in hospitalized elderly patients. Finally, data on the economic burden was only available for South Korea, with the median cost of a medical admission for an elderly patient with RSV being US dollar (USD) 2933. CONCLUSION: RSV infection is a major source of disease burden among elderly patients, especially in regions with aging populations. It also complicates the management of those with underlying diseases. Appropriate prevention strategies are required to reduce the burden among the adult, especially the elderly, population. Data gaps regarding economic burden of RSV infection in the Asia Pacific region indicates the need for further research to increase our understanding on the burden of this disease in this region.