Predictive model for the surface melting and puffing of freeze-dried amorphous materials.

It is thought that surface melting and puffing of freeze-dried amorphous materials are related to the difference between the surface temperature (Tsur) and freeze-concentrated glass transition temperature (Tg') of the materials. Although Tg' is a material-specific parameter, Tsur is affected by the type and amount of solute and freeze-drying conditions. Therefore, it will be practically useful for preventing surface melting and puffing if Tsur can be calculated using only the minimum necessary parameters. This study aimed to establish a predictive model for the surface melting and puffing of freeze-dried amorphous materials according to the calculated Tsur. First, a Tsur-predictive model was proposed under the thermodynamic equilibrium assumptions. Second, solutions with various solute mass fractions of sucrose, maltodextrin, and sucrose-maltodextrin mixture were prepared, and three material-specific parameters (Tg', unfrozen water content, and true density) were experimentally determined. According to the proposed model with the parameters, the Tsur of the samples was calculated at chamber pressures of 13, 38, and 103 Pa. The samples were freeze-dried at the chamber pressures, and their appearance was observed. As expected, surface melting and puffing occurred at calculated Tsur >Tg' with some exceptions. The water activity (aw) of the freeze-dried samples increased as the Tsur - Tg' increased. This will have resulted from surface melting and puffing, which created a covering film, thereby preventing subsequent dehydration. The observations suggest that the proposed model is also useful for predetermining the drying efficiency and storage stability of freeze-dried amorphous materials.

Effect of water activity on the mechanical glass transition and dynamical transition of bacteria.

The purpose of this study was to clarify the glass-transition behavior of bacteria (Cronobacter sakazakii) as a function of water activity (aw). From the water sorption isotherm (298 K) for C. sakazakii, monolayer water content and monolayer aw were determined to be 0.0724 g/g-dry matter and 0.252, respectively. Mechanical relaxation was investigated at 298 K. In a higher aw range of over 0.529, the degree of mechanical relaxation increased with an increase in aw. From the effect of aw on the degree of mechanical relaxation, the mechanical awc (aw at which mechanical glass transition occurs at 298 K) was determined to be 0.667. Mean-square displacement of atoms in the bacteria was investigated by incoherent elastic neutron scattering. The mean-square displacement increased gradually with an increase in temperature depending on the aw of samples. From the linear fitting, two or three dynamical transition temperatures (low, middle, and high Tds) were determined at each aw. The low-Td values (142-158 K) were almost independent from aw. There was a minor effect of aw on the middle Td (214-234 K) except for the anhydrous sample (261 K). The high Td (252-322 K) largely increased with the decrease in aw. From the aw dependence of the high Td, the dynamical awc was determined to be 0.675, which was almost equivalent to the mechanical awc. The high Td was assumed to be the glass-transition temperature (Tg), and anhydrous Tg was estimated to be 409 K. In addition, molecular relaxation time (τ) of the bacteria was calculated as a function of aw. From the result, it is suggested that the progress of metabolism in the bacterial system requires a lower τ than approximately 6 × 10-5 s.

Effects of sucrose, carnosine, and their mixture on the glass transition behavior and storage stability of freeze-dried lactic acid bacteria at various water activities.

Effects of sucrose, carnosine, and their mixture on the glass transition behavior and storage stability of freeze-dried Lactobacillus reuteri at various water activities (aw) were investigated. At aw = 0.328, the control (non-additive sample) showed viable cells as uncountable after storage at 25 °C for 4 weeks. The sucrose and sucrose-carnosine samples showed clear glass transition at a slightly lower temperature than the storage temperature, and maintained a large number of viable cells after storage. The carnosine sample crystalized during the storage, and a large reduction in viable cells was observed. At aw = 0.576, the samples showed a small endothermic shift due to glass transition, suggesting partial crystallization. The Tg decreased with increase in aw because of the water plasticizing effect. After storage, the sucrose-carnosine sample showed much higher viable cell numbers than the other samples. At aw = 0.753, the sucrose and sucrose-carnosine samples showed clear glass transition. The carnosine sample showed freeze-concentrated glass transition and subsequent ice melting. After storage, the sucrose and carnosine samples showed an uncountable and a low number of viable cells, respectively, but sucrose-carnosine maintained relatively high viable cell numbers. In addition, carnosine strongly supported the stabilizing effect of sucrose (even at low additive levels) depending on the aw. These results suggest that sucrose-carnosine shows a synergistic stabilizing effect.

Effect of polymer addition on the physical properties of freeze-dried soup solid.

The effect of polymers (gelatin, starch, and maltodextrin) on the physical properties of freeze-dried model soup (sodium chloride, sucrose, and monosodium glutamate) was investigated. The polymers were added to the soup solution at 1 or 3% (w/v), which was then freeze-dried at 25 or 50 °C. Gelatin and maltodextrin prevented crystallization of sodium chloride to a greater extent than starch under freezing. Freeze-drying was conducted above the freeze-concentrated glass transition temperature. Polymer addition prolonged drying time, but prevented structural deformation. Gelatin enhanced the physical strength of the freeze-dried solid more than starch and maltodextrin because of its gel-network. In a dissolution test, 1% gelatin, and 1 and 3% maltodextrin exhibited greater dissolution than the other samples. The drying rate was lower at 50 °C, with minor modifications to the other properties. From these results, it was concluded that 1% gelatin was useful as a physical stabilizer for freeze-dried soup. SUPPLEMENTARY INFORMATION: The online version contains supplementary material available at 10.1007/s13197-021-05161-x.

A novel dextrin produced by the enzymatic reaction of 6-α-glucosyltransferase. â ¡. Practical advantages of the novel dextrin as a food modifier.

High-molecular-weight dextrin (WS-1000) was produced from waxy corn starch and enzymatically modified to link glucose by α-1,6 glycosidic bond at the terminal point of the glucose chain, forming MWS-1000. In this study, the physical properties of MWS-1000 were characterized, and the advantages of its use as a food modifier were described. From rheological and calorimetric studies, it was found that MWS-1000 does not undergo retrogradation, but it does not prevent the retrogradation of WS-1000, suggesting that they have no intermolecular interaction in solution. Investigation of the effect of MWS-1000 on the viscoelasticity of gelatinized wheat starch showed that in the linear viscoelastic region, storage modulus decreased and tan δ increased with increase in replaced MWS-1000 content. In addition, it was confirmed that gelatinized starch containing MWS-1000 showed viscoelastic behavior similar to that of commercially available custard cream.

Novel Antifungal Compound Z-705 Specifically Inhibits Protein Kinase C of Filamentous Fungi.

The cell wall integrity signaling (CWIS) pathway is involved in fungal cell wall biogenesis. This pathway is composed of sensor proteins, protein kinase C (PKC), and the mitogen-activated protein kinase (MAPK) pathway, and it controls the transcription of many cell wall-related genes. PKC plays a pivotal role in this pathway; deficiencies in PkcA in the model filamentous fungus Aspergillus nidulans and in MgPkc1p in the rice blast fungus Magnaporthe grisea are lethal. This suggests that PKC in filamentous fungi is a potential target for antifungal agents. In the present study, to search for MgPkc1p inhibitors, we carried out in silico screening by three-dimensional (3D) structural modeling and performed growth inhibition tests for M. grisea on agar plates. From approximately 800,000 candidate compounds, we selected Z-705 and evaluated its inhibitory activity against chimeric PKC expressed in Saccharomyces cerevisiae cells in which the kinase domain of native S. cerevisiae PKC was replaced with those of PKCs of filamentous fungi. Transcriptional analysis of MLP1, which encodes a downstream factor of PKC in S. cerevisiae, and phosphorylation analysis of the mitogen-activated protein kinase (MAPK) Mpk1p, which is activated downstream of PKC, revealed that Z-705 specifically inhibited PKCs of filamentous fungi. Moreover, the inhibitory activity of Z-705 was similar to that of a well-known PKC inhibitor, staurosporine. Interestingly, Z-705 inhibited melanization induced by cell wall stress in M. grisea We discuss the relationships between PKC and melanin biosynthesis.IMPORTANCE A candidate inhibitor of filamentous fungal protein kinase C (PKC), Z-705, was identified by in silico screening. A screening system to evaluate the effects of fungal PKC inhibitors was constructed in Saccharomyces cerevisiae Using this system, we found that Z-705 is highly selective for filamentous fungal PKC in comparison with S. cerevisiae PKC. Analysis of the AGS1 mRNA level, which is regulated by Mps1p mitogen-activated protein kinase (MAPK) via PKC, in the rice blast fungus Magnaporthe grisea revealed that Z-705 had a PKC inhibitory effect comparable to that of staurosporine. Micafungin induced hyphal melanization in M. grisea, and this melanization, which is required for pathogenicity of M. grisea, was inhibited by PKC inhibition by both Z-705 and staurosporine. The mRNA levels of 4HNR, 3HNR, and SCD1, which are essential for melanization in M. grisea, were suppressed by both PKC inhibitors.

Control of Physical Changes in Food Products.

Food is a multicomponent system that mainly comprises protein, carbohydrate, fat, and water. During food processing and preservation, various physical changes (e.g., melting, crystallization, glass transition) occur in food products, affecting their quality. This chapter specifically examines the effect of physical changes on the quality of dry and frozen food products. Dry food products are commonly in an amorphous state. Therefore, glass transition occurs during their dehydration-rehydration processing. To control their texture and physical stability, it is important to elucidate the effects of water contents on the glass transition temperature of dry food products. Frozen foods consist of ice crystals and freeze-concentrated matrix. The formation of ice crystal and the dynamics of ice crystal evolution affect food quality. Therefore control of ice crystals is important for high-quality frozen food. Moreover, because freeze-concentrated matrix consists of solute that are plasticized by the unfrozen water and is in an amorphous state, it can undergo glass transition by freeze concentration. The physical state of freeze-concentrated matrix also strongly affects the stability of food quality during frozen storage.

Stabilization of freeze-dried Lactobacillus paracasei subsp. paracasei JCM 8130T with the addition of disaccharides, polymers, and their mixtures.

Although freeze-drying is a widely used dehydration technique for the stabilizing of unstable lactic acid bacteria, Lactobacillus paracasei subsp. paracasei JCM 8130T (L. paracasei) is destabilized after freeze-drying and subsequent storage. In order to improve the stability of freeze-dried L. paracasei, effects of disaccharides (sucrose and trehalose), polymers (maltodextrin; MD and bovine serum albumin; BSA), and their mixtures on the survival rate of freeze-dried L. paracasei were investigated. The survival rate of non-additive sample decreased slightly after freeze-drying but decreased drastically after subsequent storage at 37 °C for 4 weeks. The reduction was diminished by the addition of disaccharides and polymers. The stabilizing effect of disaccharides was not affected by the co-addition of MD. In contrast, the disaccharide-BSA mixtures had a synergistic stabilizing effect, and the survival rates were largely maintained even after storage. It is suggested that the synergistic effect originates from the conformational stabilization of the dehydrated bacteria.

Water Sorption Isotherm and Critical Water Activity of Amorphous Water-Soluble Carbohydrates Characterized by the Glass Transition Temperature.

Water-soluble carbohydrates commonly exist in an amorphous state in foods and undergo glass-rubber transition (glass transition) at the glass transition temperature (Tg). The critical water content (Wc) and critical water activity (awc) are the water content and water activity (aw) at which the glass transition occurs at 298 K (typical ambient temperature), respectively. For amorphous water-soluble carbohydrates, Wc can be predicted from the Tg of anhydrous solid (Tgs) using previously reported equations. However, an approach for predicting awc is still lacking. This study aimed to establish an awc-predictive approach for amorphous water-soluble carbohydrates based on Tgs. First, the water sorption isotherms of four hydrogenated starch hydrolysates were investigated, and the results were analyzed using the Guggenheim-Anderson-de Boer (GAB) model. Second, the effect of Tgs on the GAB parameters (C, K, and Wm) was evaluated using the Tgs values reported in previous literatures. C and Wm decreased and increased logarithmically, respectively, with increasing 1/Tgs. K was fixed to 1 (constant), as it showed little variation. These results enabled the prediction of the GAB parameters from Tgs. The GAB model could then predict awc from Wc, which was determined using the previously established equations. The predicted awc values were in good agreement with the experimentally determined awc. Additionally, we demonstrated that this awc-prediction approach is also applicable to amorphous water-soluble electrolytes and partially water-insoluble carbohydrates. Thus, this approach can be used for the quality control of amorphous water-soluble carbohydrates and carbohydrate-based foods.

Generation of gaseous sulfur-containing compounds in tumour tissue and suppression of gas diffusion as an antitumour treatment.

BACKGROUND AND AIMS: The mechanisms of cancer cell growth and metastasis are still not entirely understood, especially from the viewpoint of chemical reactions in tumours. Glycolytic metabolism is markedly accelerated in cancer cells, causing the accumulation of glucose (a reducing sugar) and methionine (an amino acid), which can non-enzymatically react and form carcinogenic substances. There is speculation that this reaction produces gaseous sulfur-containing compounds in tumour tissue. The aims of this study were to clarify the products in tumour and to investigate their effect on tumour proliferation. METHODS: Products formed in the reaction between glucose and methionine or its metabolites were analysed in vitro using gas chromatography. Flatus samples from patients with colon cancer and exhaled air samples from patients with lung cancer were analysed using near-edge x-ray fine adsorption structure spectroscopy and compared with those from healthy individuals. The tumour proliferation rates of mice into which HT29 human colon cancer cells had been implanted were compared with those of mice in which the cancer cells were surrounded by sodium hyaluronate gel to prevent diffusion of gaseous material into the healthy cells. RESULTS: Gaseous sulfur-containing compounds such as methanethiol and hydrogen sulfide were produced when glucose was allowed to react with methionine or its metabolites homocysteine or cysteine. Near-edge x-ray fine adsorption structure spectroscopy showed that the concentrations of sulfur-containing compounds in the samples of flatus from patients with colon cancer and in the samples of exhaled air from patients with lung cancer were significantly higher than in those from healthy individuals. Animal experiments showed that preventing the diffusion of sulfur-containing compounds had a pronounced antitumour effect. CONCLUSIONS: Gaseous sulfur-containing compounds are the main products in tumours and preventing the diffusion of these compounds reduces the tumour proliferation rate, which suggests the possibility of a new approach to cancer treatment.

Effect of Water Vapor Sorption on Complex Formation in Amylose-lauric Acid Blend Powder.

The purpose of this study was to understand the effect of relative humidity (RH) on amylose-lipid complex (ALC) formation in amylose-lauric acid blend powder held at 50 °C (temperature slightly higher than the melting point of lauric acid) using differential scanning calorimetry (DSC) and X-ray diffraction. From DSC curves, the melting of crystalized lauric acid and two melting peaks of ALC were observed depending on RH. ALC formation was confirmed by X-ray diffraction pattern. The melting enthalpy (∆Hm) of lauric acid in the sample held at RH 0 % was lower than that of lauric acid only though there was no ALC formation. This suggests that crystallization of lauric acid was prevented by amylose. The ∆Hm of lauric acid increased with an increase in RH up to 79.0 % because liquid lauric acid would have fused as the result of enhanced repulsive force between liquid lauric acid and hydrated amylose. The ∆Hm of ALC increased with an increase in RH between 79.0 and 95.0 %. For ALC formation, amylose has to be mobile in the system, but dehydrated amylose is in a glassy (immobilize) state. According to the glass to rubber transition behavior of amorphous polymer, amylose held at 50 °C is suggested to become rubbery (mobile) state at RH 76.0 %. This interpretation will explain the reason why ALC formation began to be observed at the RH range between 72.4 and 79.0 %.

Browning Behavior of Calcium Maltobionate-water System.

The purpose of the present study was to clarify the browning behavior of calcium maltobionate (CaMb). CaMb samples with varying water content (0-50 %) and water activity (0-0.98) were prepared. Absorbance due to the browning of CaMb-water samples increased linearly with an increase in holding time, and the browning rate was evaluated as a pseudo-zero-order reaction at each temperature (353-413 K). The effect of temperature on the browning rate of CaMb samples was analyzed using the Arrhenius formula, and the pre-exponential factor and activation energy were determined. In addition, the browning rate at 298 K (typical ambient condition) was determined according to the Arrhenius behavior. The browning rate at 298 K slightly decreased, markedly increased, and then decreased with an increase in water content and water activity. This behavior can be explained by the monolayer effect, plasticizing effect, and dilution effect of water molecules. There was a linear relationship between the natural logarithm of the pre-exponential factor and activation energy according to the thermodynamic compensation rule. The effect of water content on the activation energy was fitted using the cubic function. From these results, an approach for prediction of the browning of CaMB during thermal condensation was established.

Polarized Neutrons Observed Nanometer-Thick Crystalline Ice Plates in Frozen Glucose Solution.

Spin-contrast-variation (SCV) small-angle neutron scattering (SANS) is a technique to determine the nanostructure of composite materials from the scattering of polarized neutrons that changes with proton polarization of samples. The SCV-SANS enabled us to determine structure of nanoice crystals that were generated in rapidly frozen sugar solutions by separating the overlapped signals from the nanoice crystals and frozen amorphous solutions. In the frozen glucose solution, we found that the nanoice crystals formed a planar structure with a radius larger than several tens of nanometers and a thickness of 2.5 ± 0.5 nm, which was close to the critical nucleation size of ice crystals in supercooled water. This result suggests that the glucose molecules were preferentially bound to a specific face of nanoice crystals and then blocked the crystal growth perpendicular to that face.

Effects of Water and Gelatinized Starch on the Viscoelasticity of Pizza Dough and the Texture of Pizza Crust.

The soft texture of the pizza crust rim is generated by baking at a high temperature for a short period in a stone oven. In the case of baking in an electric oven, the pizza dough is baked at a much lower temperature and for a longer period, resulting in a harder texture. To improve the texture of electric oven-baked pizza crust, the effects of water and gelatinized starch on the viscoelasticity of pizza dough and the texture of pizza crust were investigated. Rheological properties (storage modulus, loss modulus, and yield stress) of pizza dough decreased with an increase in water content. When wheat flour in the dough was partially replaced with pre-gelatinized wheat starch, the rheological properties of the dough were maintained even at a high-water content. These results indicate that water-enriched dough can be prepared with gelatinized starch and baked using an electric oven. There was no significant difference in apparent density between the conventional and modified pizza crusts. Water content of the crumb part of the modified crust was significantly higher than that of the conventional crust. Texture analysis revealed that the modified pizza crust showed significantly lower stress at high strain than the conventional crust. In addition, sensory evaluation showed that the modified pizza crust exhibited greater firmness and stickiness than the conventional crust, which was attributed to the increased water content with gelatinized starch of the dough.

Discovery of a gene cluster for the biosynthesis of novel cyclic peptide compound, KK-1, in Curvularia clavata.

KK-1, a cyclic depsipeptide with 10 residues produced by a filamentous fungus Curvularia clavata BAUA-2787, is a promising pesticide active compound with high activity against many plant pathogens, especially Botrytis cinerea. As a first step toward the future mass production of KK-1 through synthetic biological approaches, we aimed to identify the genes responsible for the KK-1 biosynthesis. To achieve this, we conducted whole genome sequencing and transcriptome analysis of C. clavata BAUA-2787 to predict the KK-1 biosynthetic gene cluster. We then generated the overexpression and deletion mutants for each cluster gene using our originally developed transformation system for this fungus, and analyzed the KK-1 production and the cluster gene expression levels to confirm their involvement in KK-1 biosynthesis. As a result of these, a region of approximately 71 kb was found, containing 10 open reading frames, which were co-induced during KK-1 production, as a biosynthetic gene cluster. These include kk1B, which encodes nonribosomal peptide synthetase with a domain structure that is consistent with the structural features of KK-1, and kk1F, which encodes a transcription factor. The overexpression of kk1F increased the expression of the entire cluster genes and, consequently, improved KK-1 production, whereas its deletion decreased the expression of the entire cluster genes and almost eliminated KK-1 production, demonstrating that the protein encoded by kk1F regulates the expressions of the other nine cluster genes cooperatively as the pathway-specific transcription factor. Furthermore, the deletion of each cluster gene caused a reduction in KK-1 productivity, indicating that each gene is involved in KK-1 production. The genes kk1A, kk1D, kk1H, and kk1I, which showed a significant decrease in KK-1 productivity due to deletion, were presumed to be directly involved in KK-1 structure formation, including the biosynthesis of the constituent residues. kk1C, kk1E, kk1G, and kk1J, which maintained a certain level of KK-1 productivity despite deletion, were possibly involved in promoting or assisting KK-1 production, such as extracellular transportation and the removal of aberrant units incorporated into the peptide chain.

Why Does Cronobacter sakazakii Survive for a Long Time in Dry Environments? Contribution of the Glass Transition of Dried Bacterial Cells.

To investigate the mechanism of adaptation of Cronobacter sakazakii to desiccation stress, the present study focused on the glass transition phenomenon of dried bacterial cells, using a thermomechanical technique. The mechanical glass transition temperature (Tg) of dried C. sakazakii cells per se, prepared by different drying methods (air drying and freeze-drying) and with different water activity (aw) levels (0.43, 0.57, 0.75, and 0.87), were determined. In addition, we investigated the survival of two strains of C. sakazakii (JCM 1233 and JCM 2127) prepared by different drying methods under different storage temperatures (4, 25, and 42°C) and aw conditions (0.43 and 0.87). While the Tg of the air-dried C. sakazakii cells increased as the aw decreased, the freeze-dried C. sakazakii cells showed an unclear aw dependency of the Tg. Air-dried C. sakazakii cells showed a higher Tg than freeze-dried C. sakazakii cells at an aw of <0.57. Freeze-dried C. sakazakii cells were more rapidly inactivated than air-dried cells regardless of the difference in aw and temperature. The difference between the Tg and storage temperature was used as an index that took into consideration the differences in the drying methods and aw levels. As the difference between the Tg and storage temperature increased to >20°C, the dried C. sakazakii cells survived stably regardless of the drying method. In contrast, when the difference between the Tg and storage temperature was reduced to <10°C, the viable cell numbers in dried C. sakazakii cells were quickly decreased. Thus, the Tg is a key factor affecting the desiccation tolerance of C. sakazakii. IMPORTANCE The mechanical glass transition temperature (Tg) of dried Cronobacter sakazakii cells varied depending on differences in drying methods and water activity (aw) levels. Because the Tg of the dried bacterial cells varied depending on the drying method and aw, the Tg will play an important role as an operational factor in the optimization of dry food processing for controlling microbial contamination in the future. Furthermore, the differences between the Tg and storage temperature were introduced as an integrated index for survival of bacterial cells under a desiccation environment that took into consideration the differences in the drying methods and aw levels. As the difference between the Tg and storage temperature decreased to <10°C, the dried C. sakazakii cells were inactivated quickly, regardless of the drying methods. The relationship between Tg and storage temperature will contribute to understanding the desiccation tolerance of bacterial cells.

Effects of Trehalose Content and Water Activity on the Fracture Properties of Deep-fried Wheat Flour Particles and Freeze-dried Porous Waxy Corn Starch Solids.

Wheat flour-based batter containing 0 to 20 % trehalose was deep-fried, dried and held in various water activity (a w) conditions. The effects of trehalose content and a w on oil content, water sorption, isothermal mechanical relaxation, and fracture properties were investigated. For comparison, the fracture properties of freeze-dried porous waxy corn starch solids were also investigated. The 10 % trehalose sample had the lowest oil content, water content, and a w. A force-reduction value (∆F) of the samples was evaluated as a typical mechanical relaxation parameter. ∆F gradually increased with increasing a w and sharply increased above a specific a w presumed to be associated with the glass to rubber transition. Compared to ∆F values among the glassy samples, 10 and 20 % trehalose samples had higher ∆F values (were more rigid) than 0 and 5 % trehalose samples. From the fracture measurements of the glassy samples, the first fracture force increased linearly and the number of fracture peaks decreased linearly with increasing a w. At each a w, 10 % trehalose had the lowest first fracture force and the highest the number of fracture peaks. Freeze-dried porous waxy corn starch solids showed similar fracture properties to deep-fried samples. These findings suggest that around 10 % trehalose content is optimal for producing deep-fried foods with a brittle texture.

Effects of glass transition and hydration on the biological stability of dry yeast.

The purpose of this study was to determine the effects of glass transition and hydration on the storage stability of baker's dry yeast (Saccharomyces cerevisiae). The glass transition temperature (Tg ) of the yeast decreased with increase in water activity (aw ), and aw at which glass transition occurs at 25 °C was determined as the critical aw (awc ). From mechanical relaxation measurements at 25 °C, the yeast exhibited a large mechanical relaxation above the awc , and the degree of mechanical relaxation increased gradually with increasing aw . This behavior corresponded to a gradual increase in molecular mobility with increasing aw in the rubbery liquid state. Freezable water was observed from aw ≥0.810, and the proportion of freezable water increased with increasing aw . Examination of the effect of aw on the residual biological activity of yeast samples stored at 25 °C for 30 days revealed maximum residual biological activity at aw  = 0.225 to 0.432. In the lower aw range, the residual biological activity decreased because of oxidation of lipids. In the higher aw range, the residual biological activity decreased gradually with increasing aw . The yeast samples maintained a relatively high residual biological activity, because they could maintain relatively low molecular mobility even in the rubbery liquid state, as suggested by their mechanical relaxation behavior. At aw ≥0.809, residual activity decreased to a negligible value. This could be explained by the appearance of secondary hydrate water (freezable water). Hydrate water protects yeast cells from lipid oxidation but reduces the Tg . As a result, the yeast cells are stabilized maximally only at the awc . PRACTICAL APPLICATION: Although the growth rate of yeast cells becomes negligible below a certain aw , the biological activity of dry yeast decreases gradually during storage. The fact that dry yeast can be maximally stabilized at the awc is practically useful as a criterion for controlling storage stability. In addition, it was found that a remarkable reduction in the molecular mobility, which is otherwise ordinarily increased due to the glass-to-rubber transition, is prevented in yeast. It is possible that the crystallization of amorphous sugar can be prevented by yeast extract. The suggested effect is expected to result in enhanced quality of carbohydrate-based foods.

Physical and structural characteristics of starch-based and conventional cookies: Water sorption, mechanical glass transition, and texture properties of their crust and crumb.

The physical properties of starch-based cookie (gluten free and low fat) were compared with those of conventional cookie in consideration for the difference between crust and crumb parts. The internal porosity of the samples was measured by X-ray computed tomography. The starch-based cookie had a higher porosity (0.61) than the conventional cookie (0.42). The mechanical glass-transition temperature (Tg ) of the samples was evaluated by the thermal rheological analysis. The anhydrous mechanical Tg of the starch-based cookie was much lower than that of the conventional cookie. The Tg -depression of the starch-based cookie induced by water sorption was more gradual than that of the conventional cookie. For both types of cookie, the crust components were more resistant to water plasticizing than crumb components because of the difference of the equilibrium water contents at each water activity. For the texture analysis of crust components, the whole samples were fractured. The starch-based cookie had a lower fracture force, distance, and energy than the conventional cookie at each water activity point. For the texture analysis of crumb components, a portion of the crust was removed from the whole samples, and the exposed crumb was compressed by a plunger. From the texture profile, a normalized linear length was evaluated. The normalized linear length for the starch-based cookie was higher than that for the conventional cookie. These results were corresponded to the differences in the undeveloped gluten and fat contents.

Mechanism of action and selectivity of a novel herbicide, fenquinotrione.

Fenquinotrione is a novel herbicide that can control a wide range of broadleaf and sedge weeds with excellent rice selectivity. We revealed that fenquinotrione potently inhibited the 4-hydroxyphenylpyruvate dioxygenase (HPPD) activity in Arabidopsis thaliana with an IC50 of 44.7 nM. The docking study suggested that the 1,3-diketone moiety of fenquinotrione formed a bidentate interaction with Fe(II) at the active site. Furthermore, π-π stacking interactions occurred between the oxoquinoxaline ring and the conserved Phe409 and Phe452 rings, indicating that fenquinotrione competes with the substrate, similar to existing HPPD inhibitors. A more than 16-fold difference in the herbicidal activity of fenquinotrione in rice and the sedge, Schoenoplectus juncoides, was observed. However, fenquinotrione showed high inhibitory activity against rice HPPD. Comparative metabolism study suggested that the potent demethylating metabolism followed by glucose conjugation in rice was responsible for the selectivity of fenquinotrione.