Ultrafast deposition of faceted lithium polyhedra by outpacing SEI formation.

Electrodeposition of lithium (Li) metal is critical for high-energy batteries1. However, the simultaneous formation of a surface corrosion film termed the solid electrolyte interphase (SEI)2 complicates the deposition process, which underpins our poor understanding of Li metal electrodeposition. Here we decouple these two intertwined processes by outpacing SEI formation at ultrafast deposition current densities3 while also avoiding mass transport limitations. By using cryogenic electron microscopy4-7, we discover the intrinsic deposition morphology of metallic Li to be that of a rhombic dodecahedron, which is surprisingly independent of electrolyte chemistry or current collector substrate. In a coin cell architecture, these rhombic dodecahedra exhibit near point-contact connectivity with the current collector, which can accelerate inactive Li formation8. We propose a pulse-current protocol that overcomes this failure mode by leveraging Li rhombic dodecahedra as nucleation seeds, enabling the subsequent growth of dense Li that improves battery performance compared with a baseline. While Li deposition and SEI formation have always been tightly linked in past studies, our experimental approach enables new opportunities to fundamentally understand these processes decoupled from each other and bring about new insights to engineer better batteries.

Electrified Operando-Freezing of Electrocatalytic CO2 Reduction Cells for Cryogenic Electron Microscopy.

The ability to freeze and stabilize reaction intermediates in their metastable states and obtain their structural and chemical information with high spatial resolution is critical to advance materials technologies such as catalysis and batteries. Here, we develop an electrified operando-freezing methodology to preserve these metastable states under electrochemical reaction conditions for cryogenic electron microscopy (cryo-EM) imaging and spectroscopy. Using Cu catalysts for CO2 reduction as a model system, we observe restructuring of the Cu catalyst in a CO2 atmosphere while the same catalyst remains intact in air at the nanometer scale. Furthermore, we discover the existence of a single valence Cu (1+) state and C-O bonding at the electrified liquid-solid interface of the operando-frozen samples, which are key reaction intermediates that traditional ex situ measurements fail to detect. This work highlights our novel technique to study the local structure and chemistry of electrified liquid-solid interfaces, with broad impact beyond catalysis.

A Rapid, Scalable Laser-Scribing Process to Prepare Si/Graphene Composites for Lithium-Ion Batteries.

Silicon has gained significant attention as a lithium-ion battery anode material due to its high theoretical capacity compared to conventional graphite. Unfortunately, silicon anodes suffer from poor cycling performance caused by their extreme volume change during lithiation and de-lithiation. Compositing silicon particles with 2D carbon materials, such as graphene, can help mitigate this problem. However, an unaddressed challenge remains: a simple, inexpensive synthesis of Si/graphene composites. Here, a one-step laser-scribing method is proposed as a straightforward, rapid (≈3 min), scalable, and less-energy-consuming (≈5 W for a few minutes under air) process to prepare Si/laser-scribed graphene (LSG) composites. In this research, two types of Si particles, Si nanoparticles (SiNPs) and Si microparticles (SiMPs), are used. The rate performance is improved after laser scribing: SiNP/LSG retains 827.6 mAh g-1 at 2.0 A gSi+C -1, while SiNP/GO (before laser scribing) retains only 463.8 mAh g-1. This can be attributed to the fast ion transport within the well-exfoliated 3D graphene network formed by laser scribing. The cyclability is also improved: SiNP/LSG retains 88.3% capacity after 100 cycles at 2.0 A gSi+C -1, while SiNP/GO retains only 57.0%. The same trend is found for SiMPs: the SiMP/LSG shows better rate and cycling performance than SiMP/GO composites.

Simple and field-adapted species identification of biological specimens combining multiplex multienzyme isothermal rapid amplification, lateral flow dipsticks, and universal primers for initial rapid screening without standard PCR laboratory.

Species identification of biological specimens can provide the valuable clues and accelerate the speed of prosecution material processing for forensic investigation, especially when the case scene is inaccessible and the physical evidence is cumbersome. Thus, establishing a rapid, simple, and field-adapted species identification method is crucial for forensic scientists, particularly as first-line technology at the crime scene for initial rapid screening. In this study, we established a new field-adapted species identification method by combining multiplex multienzyme isothermal rapid amplification (MIRA), lateral flow dipstick (LFD) system, and universal primers. Universal primers targeting COX I and COX II genes were used in multiplex MIRA-LFD system for seven species identification, and a dedicated MIRA-LFD system primer targeting CYT B gene was used to detect the human material. DNA extraction was performed by collecting DNA directly from the centrifuged supernatant. Our study found that the entire amplification process took only 15 min at 37 °C and the results of LFDs could be visually observed after 10 min. The detection sensitivity of human material could reach 10 pg, which is equivalent to the detection of single cell. Different common animal samples mixed at the ratio of 1 ng:1 ng, 10 ng:1 ng, and 1 ng:10 ng could be detected successfully. Furthermore, the damaged and degraded samples could also be detected. Therefore, the convenient, feasible, and rapid approach for species identification is suitable for popularization as first-line technology at the crime scene for initial rapid screening and provides a great convenient for forensic application.

Metabolomics efficiently discriminates monozygotic twins in peripheral blood.

Monozygotic (MZ) twins cannot be distinguished using conventional forensic STR typing because they present identical STR genotypings. However, MZ twins do not always live in the same environment and often have different dietary and other lifestyle habits. Metabolic profiles are deyermined by individual characteristics and are also influenced by the environment in which they live. Therefore, they are potential markers capable of identifying MZ twins. Moreover, the production of proteins varies from organism to organism and is influenced by both the physiological state of the body and the external environment. Hence, we used metabolomics and proteomics to identify metabolites and proteins in peripheral blood to discriminate MZ twins. We identified 1749 known metabolites and 622 proteins in proteomic analysis. The metabolic profiles of four pairs of MZ twins revealed minor differences in intra-MZ twins and major differences in inter-MZ twins. Each pair of MZ twins exhibited distinct characteristics, and four metabolites-methyl picolinate, acesulfame, paraxanthine, and phenylbenzimidazole sulfonic acid-were observed in all four MZ twin pairs. These four differential exogenous metabolites conincidently show that the different external environments and life styles can be well distinguished by metabolites, considering that twins do not all have the same eating habits and living environments. Moreover, MZ twins showed different protein profiles in serum but not in whole blood. Thus, our results indicate that differential metabolites provide potential biomarkers for the personal identification of MZ twins in forensic medicine.

Quantifying the Impact of Motions on Human Aiming Performance: Evidence from Eye Tracking and Bio-Signals.

Working on a moving platform can significantly impede human performance. Previous studies on moving vehicles have often focused on the overall impact on general task performance, whereas our study's emphasis is on precise hand movements, exploring the interaction between body motion and the escalation of task difficulty. We recruited 28 participants to engage in reciprocal aiming tasks, following Paul Fitts's setting, under both in-motion and stationary conditions. The task index of difficulty (ID) was manipulated by varying the width of the targets and the distance between the targets. We measured participants' movement time (MT), performance errors, and monitored their eye movements using an eye-tracking device, heart rate (HR), and respiration rate (RR) during the tasks. The measured parameters were compared across two experimental conditions and three ID levels. Compared to the stationary conditions, the in-motion conditions degraded human aiming performance, resulting in significantly prolonged MT, increased errors, and longer durations of eye fixations and saccades. Furthermore, HR and RR increased under the in-motion conditions. Linear relationships between MT and ID exhibited steeper slopes under the in-motion conditions compared to the stationary conditions. This study builds a foundation for us to explore the control mechanisms of individuals working in dynamic and demanding environments, such as pilots in airplanes and paramedics in ambulances.

Discrimination of monozygotic twins using mtDNA heteroplasmy through probe capture enrichment and massively parallel sequencing.

Differentiating between monozygotic (MZ) twins remains difficult because they have the same genetic makeup. Applying the traditional STR genotyping approach cannot differentiate one from the other. Heteroplasmy refers to the presence of two or more different mtDNA copies within a single cell and this phenomenon is common in humans. The levels of heteroplasmy cannot change dramatically during transmission in the female germ line but increase or decrease during germ-line transmission and in somatic tissues during life. As massively parallel sequencing (MPS) technology has advanced, it has shown the extraordinary quantity of mtDNA heteroplasmy in humans. In this study, a probe hybridization technique was used to obtain mtDNA and then MPS was performed with an average sequencing depth of above 4000. The results showed us that all ten pairs of MZ twins were clearly differentiated with the minor heteroplasmy threshold at 1.0%, 0.5%, and 0.1%, respectively. Finally, we used a probe that targeted mtDNA to boost sequencing depth without interfering with nuclear DNA and this technique can be used in forensic genetics to differentiate the MZ twins.

Investigation of reversible metal ion (Li+, Na+, Mg2+, Al3+) insertion in MoTe2 for rechargeable aqueous batteries.

In this work, we report the electrochemical reactivity of MoTe2 for various metal ions with special emphasis on Al3+ ion storage in aqueous electrolytes for the first time. A stable discharge capacity of 100 mA h g-1 over 250 cycles at a current density of 1 Ag-1 could be obtained for the Al3+ ion, whereas inferior storage capacities were shown for other metal ions.

Spheres of Graphene and Carbon Nanotubes Embedding Silicon as Mechanically Resilient Anodes for Lithium-Ion Batteries.

Novel anode materials for lithium-ion batteries were synthesized by in situ growth of spheres of graphene and carbon nanotubes (CNTs) around silicon particles. These composites possess high electrical conductivity and mechanical resiliency, which can sustain the high-pressure calendering process in industrial electrode fabrication, as well as the stress induced during charging and discharging of the electrodes. The resultant electrodes exhibit outstanding cycling durability (∼90% capacity retention at 2 A g-1 after 700 cycles or a capacity fading rate of 0.014% per cycle), calendering compatibility (sustain pressure over 100 MPa), and adequate volumetric capacity (1006 mAh cm-3), providing a novel design strategy toward better silicon anode materials.

Resolving Current-Dependent Regimes of Electroplating Mechanisms for Fast Charging Lithium Metal Anodes.

Poor fast-charge capabilities limit the usage of rechargeable Li metal anodes. Understanding the connection between charging rate, electroplating mechanism, and Li morphology could enable fast-charging solutions. Here, we develop a combined electroanalytical and nanoscale characterization approach to resolve the current-dependent regimes of Li plating mechanisms and morphology. Measurement of Li+ transport through the solid electrolyte interphase (SEI) shows that low currents induce plating at buried Li||SEI interfaces, but high currents initiate SEI-breakdown and plating at fresh Li||electrolyte interfaces. The latter pathway can induce uniform growth of {110}-faceted Li at extremely high currents, suggesting ion-transport limitations alone are insufficient to predict Li morphology. At battery relevant fast-charging rates, SEI-breakdown above a critical current density produces detrimental morphology and poor cyclability. Thus, prevention of both SEI-breakdown and slow ion-transport in the electrolyte is essential. This mechanistic insight can inform further electrolyte engineering and customization of fast-charging protocols for Li metal batteries.

Designing a Nanoscale Three-phase Electrochemical Pathway to Promote Pt-catalyzed Formaldehyde Oxidation.

Gas-phase heterogeneous catalysis is a process spatially constrained on the two-dimensional surface of a solid catalyst. Here, we introduce a new toolkit to open up the third dimension. We discovered that the activity of a solid catalyst can be dramatically promoted by covering its surface with a nanoscale-thin layer of liquid electrolyte while maintaining efficient delivery of gas reactants, a strategy we call three-phase catalysis. Introducing the liquid electrolyte converts the original surface catalytic reaction into an electrochemical pathway with mass transfer facilitated by free ions in a three-dimensional space. We chose the oxidation of formaldehyde as a model reaction and observed a 25000-times enhancement in the turnover frequency of Pt in three-phase catalysis as compared to conventional heterogeneous catalysis. We envision three-phase catalysis as a new dimension for catalyst design and anticipate its applications in more chemical reactions from pollution control to the petrochemical industry.

Surgical treatment of foreign body embolus in the Middle cerebral artery secondary to neck injury.

Background: We report a case of a foreign body embolus to the middle cerebral artery and reviewed similar cases previously reported. Methods: A 30-year-old man was seen 72 days after a penetrating neck injury with a 1-month history of numbness in the left limb and impairment of the fine movement in the left hand. Radiological examination revealed a foreign body in the M2 portion of the right middle cerebral artery (MCA). The patient received arteriotomy and in situ suturing. Results: During the operation, we found a metallic foreign body at the bifurcation of the M2 upper trunk of the right MCA, narrowed distal blood vessels and thinned vessel walls. The foreign body was surrounded by granulation tissue. Both foreign body and granulation tissue were removed slowly followed by in situ suturing. Indocyanine green angiography confirmed arterial patency. Three days after the surgery, the patient developed numbness and weakness in the left arm, with a muscle strength of grade 4. Computed tomography showed partial infarction in the right temporal lobe. Then, antispasmodic drugs were used. Muscle strength recovered by 14 days after the operation. Conclusions: In the subacute stage, surgery can be conducted to remove intra-arterial foreign bodies along with their surrounding granulation tissue if computed tomography perfusion suggests a decreased blood flow reserve capacity.

Evolution of the Solid-Electrolyte Interphase on Carbonaceous Anodes Visualized by Atomic-Resolution Cryogenic Electron Microscopy.

The stability of modern lithium-ion batteries depends critically on an effective solid-electrolyte interphase (SEI), a passivation layer that forms on the carbonaceous negative electrode as a result of electrolyte reduction. However, a nanoscopic understanding of how the SEI evolves with battery aging remains limited due to the difficulty in characterizing the structural and chemical properties of this sensitive interphase. In this work, we image the SEI on carbon black negative electrodes using cryogenic transmission electron microscopy (cryo-TEM) and track its evolution during cycling. We find that a thin, primarily amorphous SEI nucleates on the first cycle, which further evolves into one of two distinct SEI morphologies upon further cycling: (1) a compact SEI, with a high concentration of inorganic components that effectively passivates the negative electrode; and (2) an extended SEI spanning hundreds of nanometers. This extended SEI grows on particles that lack a compact SEI and consists primarily of alkyl carbonates. The diversity in observed SEI morphologies suggests that SEI growth is a highly heterogeneous process. The simultaneous emergence of these distinct SEI morphologies highlights the necessity of effective passivation by the SEI, as large-scale extended SEI growths negatively impact lithium-ion transport, contribute to capacity loss, and may accelerate battery failure.

Wrinkled Graphene Cages as Hosts for High-Capacity Li Metal Anodes Shown by Cryogenic Electron Microscopy.

Lithium (Li) metal has long been considered the "holy grail" of battery anode chemistry but is plagued by low efficiency and poor safety due to its high chemical reactivity and large volume fluctuation, respectively. Here we introduce a new host of wrinkled graphene cage (WGC) for Li metal. Different from recently reported amorphous carbon spheres, WGC show highly improved mechanical stability, better Li ion conductivity, and excellent solid electrolyte interphase (SEI) for continuous robust Li metal protection. At low areal capacities, Li metal is preferentially deposited inside the graphene cage. Cryogenic electron microscopy characterization shows that a uniform and stable SEI forms on the WGC surface that can shield the Li metal from direct exposure to electrolyte. With increased areal capacities, Li metal is plated densely and homogeneously into the outer pore spaces between graphene cages with no dendrite growth or volume change. As a result, a high Coulombic efficiency (CE) of ∼98.0% was achieved under 0.5 mA/cm2 and 1-10 mAh/cm2 in commercial carbonate electrolytes, and a CE of 99.1% was realized with high-concentration electrolytes under 0.5 mA/cm2 and 3 mAh/cm2. Full cells using WGC electrodes with prestored Li paired with Li iron phosphate showed greatly improved cycle lifetime. With 10 mAh/cm2 Li metal deposition, the WGC/Li composite anode was able to provide a high specific capacity of ∼2785 mAh/g. With its roll-to-roll compatible fabrication procedure, WGC serves as a highly promising material for the practical realization of Li metal anodes in next-generation high energy density secondary batteries.

Shell-Protective Secondary Silicon Nanostructures as Pressure-Resistant High-Volumetric-Capacity Anodes for Lithium-Ion Batteries.

The nanostructure design of a prereserved hollow space to accommodate 300% volume change of silicon anodes has created exciting promises for high-energy batteries. However, challenges with weak mechanical stability during the calendering process of electrode fabrication and poor volumetric energy density remain to be solved. Here we fabricated a pressure-resistant silicon structure by designing a dense silicon shell coating on secondary micrometer particles, each consisting of many silicon nanoparticles. The silicon skin layer significantly improves mechanical stability, while the inner porous structure efficiently accommodates the volume expansion. Such a structure can resist a high pressure of over 100 MPa and is well-maintained after the calendering process, demonstrating a high volumetric capacity of 2041 mAh cm-3. In addition, the dense silicon shell decreases the surface area and thus increases the initial Coulombic efficiency. With further encapsulation with a graphene cage, which allows the silicon core to expand within the cage while retaining electrical contact, the silicon hollow structure exhibits a high initial Coulombic efficiency and fast rise of later Coulombic efficiencies to >99.5% and superior stability in a full-cell battery.

Nanoscale Nucleation and Growth of Electrodeposited Lithium Metal.

Lithium metal has re-emerged as an exciting anode for high energy lithium-ion batteries due to its high specific capacity of 3860 mAh g-1 and lowest electrochemical potential of all known materials. However, lithium has been plagued by the issues of dendrite formation, high chemical reactivity with electrolyte, and infinite relative volume expansion during plating and stripping, which present safety hazards and low cycling efficiency in batteries with lithium metal electrodes. There have been a lot of recent studies on Li metal although little work has focused on the initial nucleation and growth behavior of Li metal, neglecting a critical fundamental scientific foundation of Li plating. Here, we study experimentally the morphology of lithium in the early stages of nucleation and growth on planar copper electrodes in liquid organic electrolyte. We elucidate the dependence of lithium nuclei size, shape, and areal density on current rate, consistent with classical nucleation and growth theory. We found that the nuclei size is proportional to the inverse of overpotential and the number density of nuclei is proportional to the cubic power of overpotential. Based on this understanding, we propose a strategy to increase the uniformity of electrodeposited lithium on the electrode surface.

Revealing Nanoscale Passivation and Corrosion Mechanisms of Reactive Battery Materials in Gas Environments.

Lithium (Li) metal is a high-capacity anode material (3860 mAh g-1) that can enable high-energy batteries for electric vehicles and grid-storage applications. However, Li metal is highly reactive and repeatedly consumed when exposed to liquid electrolyte (during battery operation) or the ambient environment (throughout battery manufacturing). Studying these corrosion reactions on the nanoscale is especially difficult due to the high chemical reactivity of both Li metal and its surface corrosion films. Here, we directly generate pure Li metal inside an environmental transmission electron microscope (TEM), revealing the nanoscale passivation and corrosion process of Li metal in oxygen (O2), nitrogen (N2), and water vapor (H2O). We find that while dry O2 and N2 (99.9999 vol %) form uniform passivation layers on Li, trace water vapor (∼1 mol %) disrupts this passivation and forms a porous film on Li metal that allows gas to penetrate and continuously react with Li. To exploit the self-passivating behavior of Li in dry conditions, we introduce a simple dry-N2 pretreatment of Li metal to form a protective layer of Li nitride prior to battery assembly. The fast ionic conductivity and stable interface of Li nitride results in improved battery performance with dendrite-free cycling and low voltage hysteresis. Our work reveals the detailed process of Li metal passivation/corrosion and demonstrates how this mechanistic insight can guide engineering solutions for Li metal batteries.