Negative mixing enthalpy solid solutions deliver high strength and ductility.

Body-centred cubic refractory multi-principal element alloys (MPEAs), with several refractory metal elements as constituents and featuring a yield strength greater than one gigapascal, are promising materials to meet the demands of aggressive structural applications1-6. Their low-to-no tensile ductility at room temperature, however, limits their processability and scaled-up application7-10. Here we present a HfNbTiVAl10 alloy that shows remarkable tensile ductility (roughly 20%) and ultrahigh yield strength (roughly 1,390 megapascals). Notably, these are among the best synergies compared with other related alloys. Such superb synergies derive from the addition of aluminium to the HfNbTiV alloy, resulting in a negative mixing enthalpy solid solution, which promotes strength and favours the formation of hierarchical chemical fluctuations (HCFs). The HCFs span many length scales, ranging from submicrometre to atomic scale, and create a high density of diffusive boundaries that act as effective barriers for dislocation motion. Consequently, versatile dislocation configurations are sequentially stimulated, enabling the alloy to accommodate plastic deformation while fostering substantial interactions that give rise to two unusual strain-hardening rate upturns. Thus, plastic instability is significantly delayed, which expands the plastic regime as ultralarge tensile ductility. This study provides valuable insights into achieving a synergistic combination of ultrahigh strength and large tensile ductility in MPEAs.

Uniting tensile ductility with ultrahigh strength via composition undulation.

Metals with nanocrystalline grains have ultrahigh strengths approaching two gigapascals. However, such extreme grain-boundary strengthening results in the loss of almost all tensile ductility, even when the metal has a face-centred-cubic structure-the most ductile of all crystal structures1-3. Here we demonstrate that nanocrystalline nickel-cobalt solid solutions, although still a face-centred-cubic single phase, show tensile strengths of about 2.3 gigapascals with a respectable ductility of about 16 per cent elongation to failure. This unusual combination of tensile strength and ductility is achieved by compositional undulation in a highly concentrated solid solution. The undulation renders the stacking fault energy and the lattice strains spatially varying over length scales in the range of one to ten nanometres, such that the motion of dislocations is thus significantly affected. The motion of dislocations becomes sluggish, promoting their interaction, interlocking and accumulation, despite the severely limited space inside the nanocrystalline grains. As a result, the flow stress is increased, and the dislocation storage is promoted at the same time, which increases the strain hardening and hence the ductility. Meanwhile, the segment detrapping along the dislocation line entails a small activation volume and hence an increased strain-rate sensitivity, which also stabilizes the tensile flow. As such, an undulating landscape resisting dislocation propagation provides a strengthening mechanism that preserves tensile ductility at high flow stresses.

Origin of structural degradation in Li-rich layered oxide cathode.

Li- and Mn-rich (LMR) cathode materials that utilize both cation and anion redox can yield substantial increases in battery energy density1-3. However, although voltage decay issues cause continuous energy loss and impede commercialization, the prerequisite driving force for this phenomenon remains a mystery3-6 Here, with in situ nanoscale sensitive coherent X-ray diffraction imaging techniques, we reveal that nanostrain and lattice displacement accumulate continuously during operation of the cell. Evidence shows that this effect is the driving force for both structure degradation and oxygen loss, which trigger the well-known rapid voltage decay in LMR cathodes. By carrying out micro- to macro-length characterizations that span atomic structure, the primary particle, multiparticle and electrode levels, we demonstrate that the heterogeneous nature of LMR cathodes inevitably causes pernicious phase displacement/strain, which cannot be eliminated by conventional doping or coating methods. We therefore propose mesostructural design as a strategy to mitigate lattice displacement and inhomogeneous electrochemical/structural evolutions, thereby achieving stable voltage and capacity profiles. These findings highlight the significance of lattice strain/displacement in causing voltage decay and will inspire a wave of efforts to unlock the potential of the broad-scale commercialization of LMR cathode materials.

Compositionally complex doping for zero-strain zero-cobalt layered cathodes.

The high volatility of the price of cobalt and the geopolitical limitations of cobalt mining have made the elimination of Co a pressing need for the automotive industry1. Owing to their high energy density and low-cost advantages, high-Ni and low-Co or Co-free (zero-Co) layered cathodes have become the most promising cathodes for next-generation lithium-ion batteries2,3. However, current high-Ni cathode materials, without exception, suffer severely from their intrinsic thermal and chemo-mechanical instabilities and insufficient cycle life. Here, by using a new compositionally complex (high-entropy) doping strategy, we successfully fabricate a high-Ni, zero-Co layered cathode that has extremely high thermal and cycling stability. Combining X-ray diffraction, transmission electron microscopy and nanotomography, we find that the cathode exhibits nearly zero volumetric change over a wide electrochemical window, resulting in greatly reduced lattice defects and local strain-induced cracks. In-situ heating experiments reveal that the thermal stability of the new cathode is significantly improved, reaching the level of the ultra-stable NMC-532. Owing to the considerably increased thermal stability and the zero volumetric change, it exhibits greatly improved capacity retention. This work, by resolving the long-standing safety and stability concerns for high-Ni, zero-Co cathode materials, offers a commercially viable cathode for safe, long-life lithium-ion batteries and a universal strategy for suppressing strain and phase transformation in intercalation electrodes.

Harnessing instability for work hardening in multi-principal element alloys.

The strength-ductility trade-off has long been a Gordian knot in conventional metallic structural materials and it is no exception in multi-principal element alloys. In particular, at ultrahigh yield strengths, plastic instability, that is, necking, happens prematurely, because of which ductility almost entirely disappears. This is due to the growing difficulty in the production and accumulation of dislocations from the very beginning of tensile deformation that renders the conventional dislocation hardening insufficient. Here we propose that premature necking can be harnessed for work hardening in a VCoNi multi-principal element alloy. Lüders banding as an initial tensile response induces the ongoing localized necking at the band front to produce both triaxial stress and strain gradient, which enables the rapid multiplication of dislocations. This leads to forest dislocation hardening, plus extra work hardening due to the interaction of dislocations with the local-chemical-order regions. The dual work hardening combines to restrain and stabilize the premature necking in reverse as well as to facilitate uniform deformation. Consequently, a superior strength-and-ductility synergy is achieved with a ductility of ~20% and yield strength of 2 GPa during room-temperature and cryogenic deformation. These findings offer an instability-control paradigm for synergistic work hardening to conquer the strength-ductility paradox at ultrahigh yield strengths.

Aqueous Li-ion battery enabled by halogen conversion-intercalation chemistry in graphite.

The use of 'water-in-salt' electrolytes has considerably expanded the electrochemical window of aqueous lithium-ion batteries to 3 to 4 volts, making it possible to couple high-voltage cathodes with low-potential graphite anodes1-4. However, the limited lithium intercalation capacities (less than 200 milliampere-hours per gram) of typical transition-metal-oxide cathodes5,6 preclude higher energy densities. Partial7,8 or exclusive9 anionic redox reactions may achieve higher capacity, but at the expense of reversibility. Here we report a halogen conversion-intercalation chemistry in graphite that produces composite electrodes with a capacity of 243 milliampere-hours per gram (for the total weight of the electrode) at an average potential of 4.2 volts versus Li/Li+. Experimental characterization and modelling attribute this high specific capacity to a densely packed stage-I graphite intercalation compound, C3.5[Br0.5Cl0.5], which can form reversibly in water-in-bisalt electrolyte. By coupling this cathode with a passivated graphite anode, we create a 4-volt-class aqueous Li-ion full cell with an energy density of 460 watt-hours per kilogram of total composite electrode and about 100 per cent Coulombic efficiency. This anion conversion-intercalation mechanism combines the high energy densities of the conversion reactions, the excellent reversibility of the intercalation mechanism and the improved safety of aqueous batteries.

Author Correction: Aqueous Li-ion battery enabled by halogen conversion-intercalation chemistry in graphite.

In Fig. 3e of this Letter, the labels "Br-Cl1" and "Br-Cl2" should read "Br-Br1" and "Br-Br2", respectively. In the Methods section 'Preparation of electrodes', the phrase "anhydrous LiBr/LiCl was replaced by LiBr·H2O (99.95%; Sigma-Aldrich) and LiCl (99.95%; Sigma-Aldrich)" should read "anhydrous LiBr/LiCl was replaced by LiBr·H2O (99.95%; Sigma-Aldrich) and LiCl·H2O (99.95%; Sigma-Aldrich)". These errors have been corrected online.

Highly reversible Zn metal anode enabled by sustainable hydroxyl chemistry.

Rechargeable Zn metal batteries (RZMBs) may provide a more sustainable and lower-cost alternative to established battery technologies in meeting energy storage applications of the future. However, the most promising electrolytes for RZMBs are generally aqueous and require high concentrations of salt(s) to bring efficiencies toward commercially viable levels and mitigate water-originated parasitic reactions including hydrogen evolution and corrosion. Electrolytes based on nonaqueous solvents are promising for avoiding these issues, but full cell performance demonstrations with solvents other than water have been very limited. To address these challenges, we investigated MeOH as an alternative electrolyte solvent. These MeOH-based electrolytes exhibited exceptional Zn reversibility over a wide temperature range, with a Coulombic efficiency > 99.5% at 50% Zn utilization without cell short-circuit behavior for > 1,800 h. More important, this remarkable performance translates well to Zn || metal-free organic cathode full cells, supporting < 6% capacity decay after > 800 cycles at -40 °C.

Decoding Active Sites for Highly Efficient Semihydrogenation of Acetylene in Palladium-Copper Nanoalloys.

Accurately decoding the three-dimensional atomic structure of surface active sites is essential yet challenging for a rational catalyst design. Here, we used comprehensive techniques combining the pair distribution function and reverse Monte Carlo simulation to reveal the surficial distribution of Pd active sites and adjacent coordination environment in palladium-copper nanoalloys. After the fine-tuning of the atomic arrangement, excellent catalytic performance with 98% ethylene selectivity at complete acetylene conversion was obtained in the Pd34Cu66 nanocatalysts, outperforming most of the reported advanced catalysts. The quantitative deciphering shows a large number of active sites with a Pd-Pd coordination number of 3 distributed on the surface of Pd34Cu66 nanoalloys, which play a decisive role in highly efficient semihydrogenation. This finding not only opens the way for guiding the precise design of bimetal nanocatalysts from atomic-level insight but also provides a method to resolve the spatial structure of active sites.

High-Throughput Study of Amorphous Stability and Optical Properties of Superlattice-Like Ge-Sb-Te Thin Films.

A high-throughput ion beam sputtering system is used to synthesize compositional gradient superlattice-like (SLL) thin film libraries of Ge-Sb-Te alloys over the entire phase diagram. The optical properties and structural evolution of the Ge-Sb-Te combinatorial SLL thin film are investigated. A systematic screening over the annealing temperature, annealing time, and modulation period has elucidated the critical factors that affect the stability of the metastable phase and optical properties. It is found that amorphous stability and optical constant are highly dependent on the modulation period and chemical composition of the thin film. This data-driven approach offers new perspectives for accelerating the development of new materials with excellent optical and amorphous stability and for exploring their mechanisms, by greatly expanding the dataset of Ge-Sb-Te alloys with SLL structures through high-throughput experiments.

Interlayer Entropy Engineering Inducing the Symmetry-Broken Layered Oxide Cathodes to Activate Reversible High-Voltage Redox Reaction.

The as-reported doping entropy engineering of electrode materials that are usually realized by the sharing of multiple metal elements with the metal element from the lattice body, potentially has three shortages of stringent synthesis conditions, large active element loss, and serious lattice distortion. Herein, an interlayer entropy engineering of layered oxide cathodes is proposed, where the multiple metal ions are simultaneously intercalated into the same interlayer sites, thus avoiding the three shortages. Concretely, a novel interlayer medium-entropy V2O5 ((MnCoNiMgZn)0.26V2O5∙0.84H2O) is successfully constructed by a one-step hydrothermal method. The interlayer medium-entropy effect is revealed to be that five metal ions pre-intercalation induces the local symmetry-broken [VO6] octahedra in bilayer V2O5, thus activating the reversible high-voltage redox reaction, inhibiting the layer slip and following phase transformation by its pinning effect, and enhancing the charge transfer kinetics. As a result, the medium-entropy cathode realizes the trade-off between specific capacity and structural stability with a discharge capacity of 152 mAh g-1 at 0.1 A g-1 after 100 cycles, and a capacity retention rate of 98.7% at 0.5 A g-1 after 150 cycles for Li+ storage. This engineering provides a new guideline for the rational design of high-performance layered oxide cathodes.

Enabling Quasi-Zero-Strain Behavior of Layered Oxide Cathodes via Multiple-cations Induced Order-to-Disorder Transition.

The chemically pre-intercalated lattice engineering is widely applied to elevate the electronic conductivity, expand the interlayer spacing, and improve the structural stability of layered oxide cathodes. However, the mainstream unitary metal ion pre-intercalation generally produces the cation/vacancy ordered superstructure, which astricts the further improvement of lattice respiration and charge-carrier ion storage and diffusion. Herein, a multiple metal ions pre-intercalation lattice engineering is proposed to break the cation/vacancy ordered superstructure. Taking the bilayer V2O5 as an example, Ni, Co, and Zn ternary ions are simultaneously pre-intercalated into its interlayer space (NiCoZnVO). It is revealed that the Ni─Co neighboring characteristic caused by Ni(3d)-O(2p)-Co(3d) orbital coupling and the Co-Zn/Ni-Zn repulsion effect due to chemical bond incompatibility, endow the NiCoZnVO sample with the cation/vacancy disordered structure. This not only reduces the Li+ diffusion barrier, but also increases the diffusion dimension of Li+ (from one-dimension to two-dimension). Particularly, Ni, Co, and Zn ions co-pre-intercalation causes a prestress, which realizes a quasi-zero-strain structure at high-voltage window upon charging/discharging process. The functions of Ni ion stabilizing the lattice structure and Co or Zn ions activating more Li+ reversible storage reaction of V5+/V4+ are further revealed. The cation/vacancy disordered structure significantly enhances Li+ storage properties of NiCoZnVO cathode.

Tailoring planar slip to achieve pure metal-like ductility in body-centred-cubic multi-principal element alloys.

Uniform tensile ductility (UTD) is crucial for the forming/machining capabilities of structural materials. Normally, planar-slip induced narrow deformation bands localize the plastic strains and hence hamper UTD, particularly in body-centred-cubic (bcc) multi-principal element high-entropy alloys (HEAs), which generally exhibit early necking (UTD < 5%). Here we demonstrate a strategy to tailor the planar-slip bands in a Ti-Zr-V-Nb-Al bcc HEA, achieving a 25% UTD together with nearly 50% elongation-to-failure (approaching a ductile elemental metal), while offering gigapascal yield strength. The HEA composition is designed not only to enhance the B2-like local chemical order (LCO), seeding sites to disperse planar slip, but also to generate excess lattice distortion upon deformation-induced LCO destruction, which promotes elastic strains and dislocation debris to cause dynamic hardening. This encourages second-generation planar-slip bands to branch out from first-generation bands, effectively spreading the plastic flow to permeate the sample volume. Moreover, the profuse bands frequently intersect to sustain adequate work-hardening rate (WHR) to large strains. Our strategy showcases the tuning of plastic flow dynamics that turns an otherwise-undesirable deformation mode to our advantage, enabling an unusual synergy of yield strength and UTD for bcc HEAs.

The mutation of Japanese encephalitis virus envelope protein residue 389 attenuates viral neuroinvasiveness.

The envelope (E) protein of the Japanese encephalitis virus (JEV) is a key protein for virus infection and adsorption of host cells, which determines the virulence of the virus and regulates the intensity of inflammatory response. The mutation of multiple aa residues in the E protein plays a critical role in the attenuated strain of JEV. This study demonstrated that the Asp to Gly, Ser, and His mutation of the E389 site, respectively, the replication ability of the viruses in cells was significantly reduced, and the viral neuroinvasiveness was attenuated to different degrees. Among them, the mutation at E389 site enhanced the E protein flexibility contributed to the attenuation of neuroinvasiveness. In contrast, less flexibility of E protein enhanced the neuroinvasiveness of the strain. Our results indicate that the mechanism of attenuation of E389 aa mutation attenuates neuroinvasiveness is related to increased flexibility of the E protein. In addition, the increased flexibility of E protein enhanced the viral sensitivity to heparin inhibition in vitro, which may lead to a decrease in the viral load entering brain. These results suggest that E389 residue is a potential site affecting JEV virulence, and the flexibility of the E protein of aa at this site plays an important role in the determination of neuroinvasiveness.

Fabrication of Hollow and Hierarchical CuO Micro-Nano Cubes Wrapped by Reduced Graphene Oxide as a Prospective Anode for SIBs.

In this study, hollow and hierarchical CuO micro-nano cubes wrapped by reduced graphene oxide (H-CuO MNCs@rGO) were designed and successfully fabricated via a novel three-step wet-chemical method. Benefiting from its unique hollow and hierarchical micro-nano structures, H-CuO MNCs@rGO exhibited significantly enhanced electrochemical Na+ storage performance when utilized as anode material for sodium-ion batteries (SIBs). Specifically, H-CuO MNCs@rGO demonstrated a specific capacity of 380.9 mAh g-1 in the initial reversible cycle and a capacity retention of 218.9 mAh g-1 after 150 cycles at a current density of 300 mA g-1. Furthermore, through the dominant pseudocapacitive behavior, an optimized rate capability of 221.2 mAh g-1 at 800 mA g-1 can be obtained for H-CuO MNCs@rGO. The comprehensive Na+ storage properties of H-CuO MNCs@rGO obviously exceeded those of hollow CuO cubes (H-CuO MNCs) and bulk CuO anodes. Such enhanced Na+ storage performances of H-CuO MNCs@rGO can be attributed to its reasonable hollow and hierarchical micro-nano structures, which provide abundant redox active sites, shorten Na+ migration pathway, buffer volume expansion, and improve electronic/ionic conductivity during sodiation/desodiation process. Our strategy provides a facile and innovative approach for the design of CuO with rational micro-nano structure as a high-performance anode for SIBs, which would also be a guiding way for tailoring transition metal oxides in other scalable and functional applications.

Nucleotide at position 66 of NS2A in Japanese encephalitis virus is associated with the virulence and proliferation of virus.

Most wild strains of Japanese encephalitis virus (JEV) produce NS1' protein, which plays an important role in viral infection and immune escape. The G66A nucleotide mutation in NS2A gene of the wild strain SA14 prevented the ribosomal frameshift that prevented the production of NS1' protein, thus reduced the virulence. In this study, the 66th nucleotide of the NS2A gene of SA14 was mutated into A, U or C, respectively. Both the G66U and G66C mutations cause the E22D mutation of the NS2A protein. Subsequently, the expression of NS1' protein, plaque size, replication ability, and virulence to mice of the three mutant strains were examined. The results showed that the three mutant viruses could not express NS1' protein, and their proliferation ability in nerve cells and virulence to mice were significantly reduced. In addition, the SA14(G66C) was less virulent than the other two mutated viruses. Our results indicate that only when G is the 66th nucleotide of NS2A, the JEV can produce NS1' protein, which affects the virulence.

Various solitons induced by relative phase in the nonlinear Schrödinger Maxwell-Bloch system.

We study the effect of relative phase on the characteristics of rogue waves and solitons described by rational solutions in the nonlinear Schrödinger Maxwell-Bloch system. We derived the rational rogue wave and soliton solutions with adjustable relative phase and present the parameter range of different types of rogue waves and solitons. Our findings show that the relative phase can alter the distribution of rational solitons and even change the type of rational solitons, leading to a rich array of rational soliton types by adjusting the relative phase. However, the relative phase does not affect the structure of the rogue wave, because the relative phase of the rogue wave changes during evolution. In particular, we confirm that the rational solitons with varying relative phases and the rogue waves at corresponding different evolution positions share the same distribution mode. This relationship holds true for rogue waves or breathers and their stable counterparts solitons or periodic waves in different nonlinear systems. The implications of our study are significant for exploring fundamental excitation elements in nonlinear systems.

Towards Stabilized Few-Shot Object Detection with Less Forgetting via Sample Normalization.

Few-shot object detection is a challenging task aimed at recognizing novel classes and localizing with limited labeled data. Although substantial achievements have been obtained, existing methods mostly struggle with forgetting and lack stability across various few-shot training samples. In this paper, we reveal two gaps affecting meta-knowledge transfer, leading to unstable performance and forgetting in meta-learning-based frameworks. To this end, we propose sample normalization, a simple yet effective method that enhances performance stability and decreases forgetting. Additionally, we apply Z-score normalization to mitigate the hubness problem in high-dimensional feature space. Experimental results on the PASCAL VOC data set demonstrate that our approach outperforms existing methods in both accuracy and stability, achieving up to +4.4 mAP@0.5 and +5.3 mAR in a single run, with +4.8 mAP@0.5 and +5.1 mAR over 10 random experiments on average. Furthermore, our method alleviates the drop in performance of base classes. The code will be released to facilitate future research.

P2-Type Moisture-Stable and High-Voltage-Tolerable Cathodes for High-Energy and Long-Life Sodium-Ion Batteries.

P2-Na0.67Ni0.33Mn0.67O2 represents a promising cathode for Na-ion batteries, but it suffers from severe structural degradation upon storing in a humid atmosphere and cycling at a high cutoff voltage. Here we propose an in situ construction to achieve simultaneous material synthesis and Mg/Sn cosubstitution of Na0.67Ni0.33Mn0.67O2 via one-pot solid-state sintering. The materials exhibit superior structural reversibility and moisture insensitivity. In-operando XRD reveals an essential correlation between cycling stability and phase reversibility, whereas Mg substitution suppressed the P2-O2 phase transition by forming a new Z phase, and Mg/Sn cosubstitution enhanced the P2-Z transition reversibility benefiting from strong Sn-O bonds. DFT calculations disclosed high chemical tolerance to moisture, as the adsorption energy to H2O was lower than that of the pure Na0.67Ni0.33Mn0.67O2. A representative Na0.67Ni0.23Mg0.1Mn0.65Sn0.02O2 cathode exhibits high reversible capacities of 123 mAh g-1 (10 mA g-1), 110 mAh g-1 (200 mA g-1), and 100 mAh g-1 (500 mA g-1) and a high capacity retention of 80% (500 mA g-1, 500 cycles).

Atomic Three-Dimensional Investigations of Pd Nanocatalysts for Acetylene Semi-hydrogenation.

Deciphering the three-dimensional (3D) insight into nanocatalyst surfaces at the atomic level is crucial to understanding catalytic reaction mechanisms and developing high-performance catalysts. Nevertheless, better understanding the inherent insufficiency of a long-range ordered lattice in nanocatalysts is a big challenge. In this work, we report the local structure of Pd nanocatalysts, which is beneficial for demonstrating the shape-structure-adsorption relationship in acetylene hydrogenation. The 5.27 nm spherical Pd catalyst (Pdsph) shows an ethylene selectivity of 88% at complete acetylene conversion, which is much higher than those of the Pd octahedron and Pd cube and superior to other reported monometallic Pd nanocatalysts so far. By virtue of the local structure revelation combined with the atomic pair distribution function (PDF) and reverse Monte Carlo (RMC) simulation, the atomic surface distribution of the unique compressed strain of Pd-Pd pairs in Pdsph was revealed. Density functional theory calculations verified the obvious weakening of the ethylene adsorption energy on account of the surface strain of Pdsph. It is the main factor to avoid the over-hydrogenation of acetylene. The present work, entailing shape-induced surface strain manipulation and atomic 3D insight, opens a new path to understand and optimize chemical activity and selectivity in the heterogeneous catalysis process.