Widening the applicability of AnMBR for urban wastewater treatment through PDMS membranes for dissolved methane capture: Effect of temperature and hydrodynamics.

AnMBR technology is a promising alternative to achieve future energy-efficiency and environmental-friendly urban wastewater (UWW) treatment. However, the large amount of dissolved methane lost in the effluent represents a potential high environmental impact that hinder the feasibility of this technology for full-scale applications. The use of degassing membranes (DM) to capture the dissolved methane from AnMBR effluents can be considered as an interesting alternative to solve this problem although further research is required to assess the suitability of this emerging technology. The aim of this study was to assess the effect of operating temperature and hydrodynamics on the capture of dissolved methane from AnMBR effluents by DMs. To this aim, a commercial polydimethylsiloxane (PDMS) DM was coupled to an industrial prototype AnMBR (demonstration scale) treating UWW at ambient temperature. Different operating temperatures have been evaluated: 11, 18, 24 and 30 °C. Moreover, the DM was operated at different ratios of liquid flow rate to membrane area (QL:A) ranging from 22 to 190 Lh-1m-2 in order to study the resistance of the system to methane permeation. Methane recovery was maximized when temperature raised and QL:A was reduced, giving methane recovery efficiencies (MRE) of about 85% at a temperature of 30 °C and a QL:A of 25 Lh-1m-2. The study showed that high QL:A ratios hinder methane recovery by the perturbation of the DM fibers, being this effect intensified at lower temperatures probably due the higher liquid viscosities. Also, the performed fouling evaluation showed that not significant membrane fouling may be expected in the DM unit at the short-term when treating AnMBR effluents. A resistance-in-series model was proposed to predict the overall mass transfer of the system according to operating temperature and QL:A, showing that methane capture was controlled by the liquid phase, which represented up to 80-90% of total mass transfer resistance. The energy and environmental evaluation performed in this study revealed that PDMS DMs would enhance energy recovery and environmental feasibility of AnMBR technology for UWW treatment, especially when operating at low temperatures. When MRE was maximized, the combination of AnMBR with DM achieved net energy productions and net greenhouse gas reductions of up to 0.87 kWh and 0.216 kg CO2-eq per m3 of treated water.

Direct Membrane Filtration of Municipal Wastewater: Studying the Most Suitable Conditions for Minimizing Fouling Rate in Commercial Porous Membranes at Demonstration Scale.

This study aimed to evaluate the feasibility of applying a commercial porous membrane to direct filtration of municipal wastewater. The effects of membrane pore size (MF and UF), treated influent (raw wastewater and the primary settler effluent of a municipal wastewater treatment plant) and operating solids concentration (about 1 and 2.6 g L-1) were evaluated on a demonstration plant. Filtration periods of 2-8 h were achieved when using the MF membrane, while these increased to 34-69 days with the UF membrane. This wide difference was due to severe fouling when operating the MF membrane, which was dramatically reduced by the UF membrane. Use of raw wastewater and higher solids concentration showed a significant benefit in the filtration performance when using the UF module. The physical fouling control strategies tested (air sparging and backwashing) proved to be ineffective in controlling UF membrane fouling, although these strategies had a significant impact on MF membrane fouling, extending the operating period from some hours to 5-6 days. The fouling evaluation showed that a cake layer seemed to be the predominant reversible fouling mechanism during each independent filtration cycle. However, as continuous filtration advanced, a large accumulation of irreversible fouling appeared, which could have been related to intermediate/complete pore blocking in the case of the MF membrane, while it could have been produced by standard pore blocking in the case of the UF membrane. Organic matter represented more than 70% of this irreversible fouling in all the experimental conditions evaluated.

Dynamic Membranes for Enhancing Resources Recovery from Municipal Wastewater.

This paper studied the feasibility of using dynamic membranes (DMs) to treat municipal wastewater (MWW). Effluent from the primary settler of a full-scale wastewater treatment plant was treated using a flat 1 µm pore size open monofilament polyamide woven mesh as supporting material. Two supporting material layers were required to self-form a DM in the short-term (17 days of operation). Different strategies (increasing the filtration flux, increasing the concentration of operating solids and coagulant dosing) were used to enhance the required forming time and pollutant capture efficiency. Higher permeate flux and increased solids were shown to be ineffective while coagulant dosing showed improvements in both the required DM forming time and permeate quality. When coagulant was dosed (10 mg L-1) a DM forming time of 7 days and a permeate quality of total suspended solids, chemical oxygen demand, total nitrogen, total phosphorous and turbidity of 24 mg L-1, 58 mg L-1, 38.1 mg L-1, 1.2 mg L-1 and 22 NTU, respectively, was achieved. Preliminary energy and economic balances determined that energy recoveries from 0.032 to 0.121 kWh per m3 of treated water at a cost between €0.002 to €0.003 per m3 of treated water can be obtained from the particulate material recovered in the DM.

Evaluating the Feasibility of Employing Dynamic Membranes for the Direct Filtration of Municipal Wastewater.

The aim of this study was to assess the feasibility of using dynamic membranes for direct filtration of municipal wastewater. The influence of different alternative supporting materials (one or two layers of flat open monofilament woven polyamide meshes with 1 or 5 µm of pore size) was studied. A stable short-term self-forming DM was achieved (from some hours to 3 days) regardless of the supporting material used, producing relatively similar permeate qualities (total suspended solids, chemical oxygen demand, total nitrogen, total phosphorous and turbidity of 67-88 mg L-1, 155-186 mg L-1, 48.7-50.4 mg L-1, 4.7-4.9 mg L-1, and 167-174 NTU, respectively). A DM permeability loss rate of from 5.21 to 10.03 LMH bar-1 day-1 was obtained, which depended on the supporting material used. Unfortunately, the preliminary energy, carbon footprint, and economic evaluations performed showed that although DMs obtain higher pollutant captures than conventional treatments (primary settler), the benefits are not enough to justify their use for treating average municipal wastewater. However, this alternative scheme could be suitable for treating higher-loaded MWW with a higher fraction of organic matter in the non-settleable solids.