Retention of strength and ion release of some restorative materials.

This study aimed to investigate the retention of strength in accelerated aging condition and ion release from an experimental fiber-reinforced bioactive flowable composite resin (Bio-SFRC), comparing it with various commercially available ion-releasing materials. The flexural strength of Bio-SFRC and other materials (Biodentine, TheraCal LC, Fuji II LC and Surefil one) was evaluated (n = 8) before and after hydrothermal accelerated aging. Ion concentrations of silica and phosphorus were measured after 1, 2, 3, 4, 7, 10, 14, and 21 days of specimen immersion in simulated body fluids (SBF) using UV-Vis spectrometry. In addition, ion release and pH change were studied in a continuous dynamic system in SBF over a period of 72 h. SEM and EDS were used to evaluate the microstructure on the top surface of the materials after SBF immersion. Data were statistically analyzed using variance ANOVA analysis (p = 0.05). Bio-SFRC showed higher flexural strength before (134.9 MPa) and after (63.1 MPa) hydrothermal aging compared to other tested materials (p < 0.05). Flexural strength significantly decreased after aging (p < 0.05) except for Fuji II LC which showed no significant differences. Ion release data showed that experimental Bio-SFRC slowly released phosphate ions. Biodentine and TheraCal LC had the strongest ability to form calcium phosphate precipitation on the material surface. Phosphate ion release cannot be detected clearly from these materials. Surefil one and Fuji II LC were more stable materials without any observable ion release. The advantages of fiber containing structure and slow release of ions suggest that experimental Bio-SFRC is a promising bioactive material to provide ions for mineralization of surrounding tissues, and keeping the durability of the materials at higher level than that of other tested materials.

Clinical evaluation of posterior flowable short fiber-reinforced composite restorations without proximal surface coverage.

The purpose of this clinical trail was to assess the clinical behavior of posterior composite restorations supported by a substantial foundation of flowable short fiber-reinforced composite SFRC (everX Flow, GC, Japan) used without proximal surface coverage with particulate filler resin composite (PFC). Seventy patients (20 males, 50 females; mean age: 30 ± 10 years) were randomly enrolled in this trial. Patients received direct restorations of either SFRC covered only on the occlusal surface (1-2 mm) by conventional PFC composite (G-ænial Posterior, GC), or plain conventional PFC composite without fiber-reinforcement, in Class II cavities in premolar and molar vital teeth. One operator made all restorations using one-step, self-etch bonding agent (G-ænial Bond, GC) according to manufacturers' recommendations. Two blinded trained operators evaluated the restorations at baseline, at 6, 12 and 18 months using modified USPHS criteria. Results indicated that, in both groups and at different follow-up intervals, according to evaluated criteria, restorations were rated mostly with best score (Alpha) (p > 0.05). For the marginal integrity after 6 months, a single case in the intervention [increased to 3 (8.8%) after 18 months] and 3 (9.7%) cases of the control group [increased to 4 (12.9%) after 18 months] had Bravo score but with no significant difference (p > 0.05). For color match measured after 6 and 18 months, three (8.8%) cases had Bravo score in the intervention group. The use of flowable SFRC composite without any PFC surface coverage proximally in Class II restorations demonstrated satisfactory clinical outcome throughout the 18-month follow-up.

Load-bearing capacity and wear characteristics of short fiber-reinforced composite and glass ceramic fixed partial dentures.

The aim of this study was to evaluate load-bearing capacity and wear performance of experimental short fiber-reinforced composite (SFRC) and conventional lithium-disilicate CAD/CAM fabricated fixed partial dentures (FPDs). Two groups (n = 12/group) of three-unit CAD/CAM fabricated posterior FPDs were made. The first group used experimental SFRC blocks, and the second group fabricated from lithium-disilicate (IPS e.max CAD). All FPDs were luted on a zirconia testing jig with dual-curing resin cement. Half of FPDs per group were quasi-statically loaded until fracture. The other half experienced cyclic fatigue aging (100.000 cycles, Fmax = 500 N) before loading quasi-statically until fracture. Fracture mode was examined using SEM. Wear test was performed using 15,000 loading cycles. Both material type and aging had a significant effect on the load-bearing capacity of FPDs. Experimental SFRC CAD without fatigue aging had significantly the highest load-bearing capacity (2096 ± 149N). Cyclic fatigue aging decreased the load-bearing capacity of the SFRC group (1709 ± 188N) but increased it for the lithium-disilicate group (1546 ± 155N). Wear depth values of SFRC CAD (29.3µm) were significantly lower compared to lithium-disilicate (54.2µm). Experimental SFRC CAD demonstrated the highest load-bearing capacity before and after cyclic fatigue aging, and superior wear behavior compared to the control material.

Wear behavior at margins of direct composite with CAD/CAM composite and enamel.

OBJECTIVES: The aim was to investigate the two-body wear at the marginal area between direct filling composites and substrate of CAD/CAM composites or enamel. MATERIALS AND METHODS: Flat specimens were prepared from CAD/CAM composites (CERASMART 270 and SFRC CAD) and bovine enamel. A box-shaped cavity cut into CAD/CAM composites and enamel surfaces was made. The prepared cavity in CAD/CAM composites was treated with a primer, while in enamel, the cavity was treated with an adhesive. Three conventional composites (Universal Injectable, G-aenial A'Chord, and Filtek Bulk Fill) and one short fiber composite (everX Flow) were placed and cured in the prepared cavities. A two-body wear test was conducted with 15,000 chewing cycles using a dual-axis chewing simulator. The specimens (n = 5/per group) were positioned to produce wear (load = 20 N) across the marginal area between filling composites and substrates. The wear depth was analyzed using a 3D optical profilometer. SEM was used to evaluate the wear behavior and margins between the filling and substrate materials. RESULTS: All composites used displayed different wear behavior (20-39 µm) (p < 0.05). The highest wear values were recorded for A'Chord and Filtek, while the lowest values were for Injectable and CERASMART 270. The data analysis showed that the wear behavior of substrate materials depends on the filling materials used at margins (p < 0.05). The marginal breakdown was seen only between bovine enamel and filling composites. CONCLUSIONS: The use of the two-body wear simulation method revealed important information about the behavior of the filling composites at the marginal area with CAD/CAM composites or bovine enamel substrates. CLINICAL RELEVANCE: The marginal breakdown related to the material combination at the bonding region.

Improving light-cured intermediate resin for hard and space mouthguard using a glass fiber.

BACKGROUND/AIMS: A light-cured intermediate material is useful for fabricating a hard insert and a buffer space mouthguard (H&SMG). However, it requires improvement in its mechanical properties and shock-absorbing capacity. The aim of this study was to evaluate the mechanical properties of two prototype light-cured intermediate materials reinforced with glass fibers, and the impact absorption capacity and durability of H&SMGs made with the prototype intermediate materials. MATERIALS AND METHODS: Two prototype materials containing long and microlength glass fibers in a light-cured intermediate material, Innerframe LC®, for H&SMG, were fabricated and tested. A three-point bending test was performed for evaluation of the mechanical properties. In addition, a shock absorption test was conducted using a customized pendulum impact testing machine to evaluate the H&SMGs' impact absorption capacity and durability. RESULTS: Long and microlength glass fibers significantly improved flexural modulus and strength. H&SMGs made with these two glass fiber-containing materials had high impact absorption capacity against both low and high impact forces, while the mouthguards made with long glass fiber materials had the best results. CONCLUSION: Long and microlength glass fibers with the prototype materials improved the mechanical properties of Innerframe LC® and the impact absorption capacity and durability of H&SMGs. H&SMGs made with the long glass fiber prototype materials had the best performance.

Fatigue performance of endodontically treated premolars restored with direct and indirect cuspal coverage restorations utilizing fiber-reinforced cores.

OBJECTIVES: The aim of this in vitro study was to investigate the fatigue survival and fracture behavior of endodontically treated (ET) premolars restored with different types of post-core and cuspal coverage restorations. MATERIALS AND METHODS: MOD cavities were prepared on 108 extracted maxillary premolars. During the endodontic treatment, all teeth were instrumented with rotary files (ProTaper Universal) to the same apical enlargement (F2) and were obturated with a matched single cone obturation. After the endodontic procedure, the cavities were restored with different post-core and overlay restorations (n = 12/group). Three groups (A1-A3) were restored with either conventional composite core (PFC; control) or flowable short-fiber-reinforced composite (SFRC) core with/without custom-made fiber posts and without overlays. Six groups had similar post-core foundations as described above but with either direct PFC (B1-B3) or indirect CAD/CAM (C1-C3) overlays. Fatigue survival was tested for all restorations using a cyclic loading machine until fracture occurred or 50,000 cycles were completed. Kaplan-Meyer survival analysis was conducted, followed by pairwise post hoc comparisons. RESULTS: None of the restored teeth survived all 50,000. Application of flowable SFRC as luting-core material with fiber post and CAD/CAD overlays (Group C3) showed superior performance regarding fatigue survival (p < 0.05) to all the other groups. Flowable SFRC with fiber post and direct overlay (Group B3) showed superior survival compared to all other direct techniques (p < 0.05), except for the same post-core foundation but without cuspal coverage (Group A3). CONCLUSIONS: Custom-made fiber post and SFRC as post luting core material with or without cuspal coverage performed well in terms of fatigue resistance and survival when used for the restoration of ET premolars. CLINICAL RELEVANCE: The fatigue survival of direct and indirect cuspal coverage restorations in ET MOD premolars is highly dependent on whether the core build-up is fiber-reinforced or not. The combination of short and long fibers in the form of individualized post-cores seems to offer a favorable solution in this situation.

Small-Molecule-based Supramolecular Plastics Mediated by Liquid-Liquid Phase Separation.

Plastics are one of the most widely used polymeric materials. However, they are often undegradable and non-recyclable due to the very stable covalent bonds of macromolecules, causing environmental pollution and health problems. Here, we report that liquid-liquid phase separation (LLPS) could drive the formation of robust, stable, and sustainable plastics using small molecules. The LLPS process could sequester and concentrate solutes, strengthen the non-covalent association between molecules and produce a bulk material whose property was highly related to the encapsulated water amounts. It was a robust plastic with a remarkable Young's modulus of 139.5 MPa when the water content was low while became adhesive and could instantly self-heal with more absorbed water. Finally, responsiveness enabled the material to be highly recyclable. This work allowed us to understand the LLPS at the molecular level and demonstrated that LLPS is a promising approach to exploring eco-friendly supramolecular plastics that are potential substitutes for conventional polymers.

Shear-bond strength and optical properties of short fiber-reinforced CAD/CAM composite blocks.

The aim of this study was to assess the shear-bond strength (SBS) of resin-luting cement to experimental short fiber-reinforced CAD/CAM composite (SFRC) compared to conventional CAD/CAM (Cerasmart 270), 3D printed (GC TEMP PRINT, Pro3dure GR-17), and laboratory (Gradia Plus) composites. Moreover, translucency parameter values and light transmission were evaluated. For each of the five types of composites, discs were prepared (n = 16/group) and divided into subgroups (n = 8/group) according to surface treatment protocol (hydrofluoric acid or air-particle abrasion). SBS test was performed using universal testing machine until failure, and failure modes were visually analyzed. Translucency parameter and curing-light transmission values through 1, 2, and 3 mm thickness were quantified using spectrophotometry and the MARC resin calibrator, respectively. Scanning electron microscopy (SEM) was used to examine the CAD/CAM composites after surface treatment. Composite type and surface treatment had a significant effect on SBS. Laboratory composite showed the highest SBS value (22.4 MPa). Cerasmart 270 exhibited higher translucency parameter values (19.8, 11.0, 5.0) than SFRC (14.5, 5.2, 1.6) at the three composite thicknesses tested. Air-particle abrasion was more effective in enhancing SBS than acid etching. Experimental SFRC CAD/CAM composite showed higher SBS values than Cerasmart 270. For all composites, translucency parameter values and light transmission decreased as thickness increased.

Fatigue failure load of immature anterior teeth: influence of different fiber post-core systems.

The aim was to explore the fracture-behavior, survival and marginal-microgaps within the root-canal of immature anterior teeth restored with different fiber-reinforced post-core composites (FRCs). 180 bovine-incisors were randomly divided into 6 groups (n = 30). One group served as control (group 6). The rest of the teeth were prepared to an internal diameter of 1.6 mm and the apex was sectioned. After application of an MTA-plug, teeth were restored with FRC materials: Group 1: Bioblock technique with short fiber-reinforced composite (SFRC); Group 2: Bioblock technique with flowable SFRC; Group 3: Individually-made FRC post; Group 4: Conventional FRC post; Group 5: dual-cure core build-up composite. After restorations were completed, teeth (n = 5/group) were sectioned and then stained. Specimens were viewed under a stereo microscope and the percentage of microgaps within the root-canal was calculated. Fatigue-survival was measured using a cyclic-loading testing machine in the rest of the specimens. Flowable SFRC application in the root-canal (Group 2) did not differ from intact-teeth regarding fatigue-survival (p > 0.05). The rest of the groups produced significantly lower survival (p < 0.05) compared to intact-teeth. Post/core restorations made from conventional FRC post (Group 4) exhibited a high number of microgaps (38.3%) at the examined interphase in the root-canal. The restoration of immature incisors with the use of flowable SFRC as post-core material displayed promising performance in a matter of fatigue-resistance and survival.

Assessment of CAD-CAM polymers for digitally fabricated complete dentures.

STATEMENT OF PROBLEM: Information on the mechanical properties of the materials used for manufacturing computer-engineered complete dentures is scarce. PURPOSE: The purpose of this in vitro study was to evaluate the mechanical properties of 3 prepolymerized polymethyl methacrylate (PMMA) resins used in the fabrication of computer-aided design and computer-aided manufacturing (CAD-CAM) milled complete dentures (CDs), as well as 2 denture base polymers used for conventionally fabricated CDs. MATERIAL AND METHODS: Three CAD-CAM materials were evaluated: Degos Dental L-Temp, IvoBase CAD, and Zirkonzahn Temp Basic Tissue. Two materials used for conventionally manufactured dentures were also included as controls (Palapress and Paladon 65). Each material type was sectioned into bars for flexural strength, nanohardness, elastic modulus, and surface microhardness evaluation (n=8/material). Half of the specimens were stored in water for 30 days, while the other half was dry-stored. A 2-way ANOVA was conducted to detect the effect of material and storage on the evaluated properties (α=.05). Linear contrasts were conducted to compare the differences among the 3 types of CAD-CAM material and the conventional ones. RESULTS: Material type and storage had a significant influence on the flexural strength, nanohardness, elastic modulus, and surface hardness of the materials investigated (P<.001). The post hoc Scheffé test for flexural strength revealed a nonsignificant difference in the interaction between Degos L-Temp and Paladon (P=1.000). In terms of nanohardness, no difference was found when comparing Palapress with Paladon, as well as IvoBase CAD with Zirkonzahn Temp Basic (P=1.000). A nonsignificant interaction in terms of surface hardness was also found between IvoBase CAD and Palapress (P=.575). CONCLUSIONS: The tested materials showed variation in their mechanical properties, with satisfactory behavior of the CAD-CAM materials. However, the results obtained when testing the materials used for the conventional fabrication of complete dentures suggest that their use might still be advisable.

Midline denture base strains of glass fiber-reinforced single implant-supported overdentures.

STATEMENT OF PROBLEM: The fracture incidence of implant-supported overdentures is more frequent in the area of attachment because of stress concentration and denture deformation in this area. How E-glass fiber reinforcement can address this problem is unclear. PURPOSE: The purpose of this in vitro study was to evaluate the influence of unidirectional E-glass fiber reinforcement on the mid-line denture base strains of single implant-supported overdentures. MATERIAL AND METHODS: An experimental acrylic resin cast was constructed with a single implant placed in the mid-line area and a ball attachment screwed to the implant. Twenty-four experimental overdentures were constructed and divided into 4 groups: group AP fabricated from autopolymerizing acrylic resin without fiber reinforcement, group APF fabricated from autopolymerizing acrylic resin with unidirectional E-glass fiber reinforcement running over the residual ridge and the ball matrix, group HP fabricated from heat-polymerized acrylic resin without fiber reinforcement, and group HPF fabricated from heat-polymerized acrylic resin with unidirectional E-glass fiber reinforcement running over the residual ridge and the ball matrix. A biaxial rosette strain gauge was attached to the incisor areas of each overdenture above the attachment level (Ch1, Ch2) and to a multichannel digital strain meter. A static vertical load of 100 N was applied to the first molar area bilaterally by using a universal testing device during strain measurement procedures. The differences in the mean strain and deflection values among the investigated groups were evaluated for statistical significance using 1-way analysis of variance (ANOVA) with the Tukey post hoc multiple comparison (α=.05). RESULTS: The type of acrylic resin did not have a statistically significant effect on the mean strain values among groups (P=.350), while the reinforcement did significantly affect them (P<.001). The interaction between reinforcement and acrylic resin was not statistically significant (P=.552). Both strain gauge channels in group APF and group HPF recorded significantly lower strain values by almost 50% than those of group AP and group HP (P<.05). CONCLUSIONS: Unidirectional E-glass fiber reinforcement placed over the residual ridge and implant attachment significantly reduced denture base strains and deformation of single implant-supported overdentures.

Incorporation of cellulose fiber in glass ionomer cement.

This study investigated the effect of discontinuous cellulose microfibers with various loading fractions on selected physical properties of glass polyalkenoate (glass ionomer) cement (GIC). Fiber-reinforced GIC (Exp-GIC) was prepared by adding discontinuous cellulose microfiber (with an average length of 500 µm) at various mass ratios (1, 2, 3, 4, and 5 mass%) to the powder of conventional GIC (GC Fuji IX) using a high-speed mixing device. Fracture toughness, work of fracture, and compressive strength were determined for each experimental and control material. The specimens (n = 6) were wet stored (37°C for 1 d) before testing. A scanning electron microscope equipped with an energy dispersive spectroscope was used to examine the surface of fibers after treatment with cement liquid. Data were analyzed using ANOVA. The Exp-GIC (5 mass%) specimen had statistically significantly higher fracture toughness (0.9 MPa.m1/2 ) than unreinforced material (0.4 MPa.m1/2 ). On the other hand, Exp-GIC with 1 mass% displayed the highest compressive strength (116 MPa) among all tested groups. The use of discontinuous cellulose microfibers with conventional GIC matrix considerably increased the toughening performance compared with the particulate GICs used.

Fracture resistance and marginal gap formation of post-core restorations: influence of different fiber-reinforced composites.

OBJECTIVES: The aim was to explore the fracture behavior and marginal gap within the root canal of endodontically treated (ET) premolars restored with different fiber-reinforced post-core composites (FRCs). Further aim was to evaluate the composite curing at different depths in the canal. MATERIALS AND METHODS: Eighty-seven intact upper premolars were collected and randomly divided into six groups. After endodontic procedure, standard MOD cavities were prepared and restored with their respective fiber-reinforced post-core materials: group 1: prefabricated unidirectional FRC-post + conventional composite core; group 2: prefabricated unidirectional FRC-post + short fiber composite (SFRC) core; group 3: individually formed unidirectional FRC-post + conventional composite core; group 4: randomly oriented SFRC directly layered as post and core; group 5: individually formed unidirectional FRC + randomly oriented SFRC as post and core. After restorations were completed, teeth (n = 3/group) were sectioned and then stained. Specimens were viewed under a stereo microscope and the percentage of microgaps within the root canal was calculated. Fracture load was measured using universal testing machine. RESULTS: SFRC application in the root canal (groups 4 and 5) showed significantly higher fracture load (876.7 N) compared to the other tested groups (512-613 N) (p < 0.05). Post/core restorations made from prefabricated FRC-post (group 1) exhibited the highest number of microgaps (35.1%) at the examined interphase in the root canal. CONCLUSIONS: The restoration of ET premolars with the use of SFRC as post-core material displayed promising performance in matter of microgap and load-bearing capacity. CLINICAL SIGNIFICANCE: Fracture resistance of ET premolar restored by bilayered composite restoration that includes both SFRC as post-core material and surface conventional resin seems to be beneficial.

Effect of interface surface design on the fracture behavior of bilayered composites.

This study aimed to evaluate the effect of different interface designs on the load-bearing capacity of bilayered composite structures (BLS). Cylindrical specimens of BLS were prepared from base composite of 3.5 mm thickness and surface composite of 1.5 mm thickness (n = 80). Two different base composites - flowable bulk-fill (FBF) [smart dentin replacement (SDR)] and short fiber-reinforced (FRC) (everX Posterior) - were evaluated, and conventional composite (G-aenial Posterior) was used as the surface layer. Four different interface designs were used: (i) pyramidal; (ii) mesh; (iii) linear grooves; and (iv) flat surface (control). Three-dimensional printed molds were fabricated to standardize the interface design between the surface and the base composites. The specimens were then statically loaded with a steel ball until fracture using a universal testing machine. Fracture types were classified into catastrophic, complete, and partial bulk. ANOVA revealed that both the material and the interface design had a statistically significant effect on the load-bearing capacity. Flowable bulk-fill showed lower mean load-bearing capacity than FRC in all the interface designs tested, except for the flat surface design. Fracture analysis showed that FRC demonstrated up to 100% partial bulk fractures with the pyramid interface design, but no incidence of catastrophic bulk fracture. By contrast, FBF demonstrated up to 84.6% and 40% catastrophic bulk fractures with the flat interface design but no incidence of partial bulk fracture. Consequently, the interface designs studied enhanced the fracture behavior of BLS.

Scattering of therapeutic radiation in the presence of craniofacial bone reconstruction materials.

PURPOSE: Radiation scattering from bone reconstruction materials can cause problems from prolonged healing to osteoradionecrosis. Glass fiber reinforced composite (FRC) has been introduced for bone reconstruction in craniofacial surgery but the effects during radiotherapy have not been previously studied. The purpose of this study was to compare the attenuation and back scatter caused by different reconstruction materials during radiotherapy, especially FRC with bioactive glass (BG) and titanium. METHODS: The effect of five different bone reconstruction materials on the surrounding tissue during radiotherapy was measured. The materials tested were titanium, glass FRC with and without BG, polyether ether ketone (PEEK) and bone. The samples were irradiated with 6 MV and 10 MV photon beams. Measurements of backscattering and dose changes behind the sample were made with radiochromic film and diamond detector dosimetry. RESULTS: An 18% dose enhancement was measured with a radiochromic film on the entrance side of irradiation for titanium with 6 MV energy while PEEK and FRC caused an enhancement of 10% and 4%, respectively. FRC-BG did not cause any measurable enhancement. The change in dose immediately behind the sample was also greatest with titanium (15% reduction) compared with the other materials (0-1% enhancement). The trend is similar with diamond detector measurements, titanium caused a dose enhancement of up to 4% with a 1 mm sample and a reduction of 8.5% with 6 MV energy whereas FRC, FRC-BG, PEEK or bone only caused a maximum dose reduction of 2.2%. CONCLUSIONS: Glass fiber reinforced composite causes less interaction with radiation than titanium during radiotherapy and could provide a better healing environment after bone reconstruction.

Characterization of a new fiber-reinforced flowable composite.

This study aimed to evaluate certain physical properties including surface wear of a new experimental short fiber-reinforced flowable resin composite (SFRC) in comparison with different commercial flowable bulk fill resin composites (SDR, Tetric EvoFlow Bulk Fill, Filtek Bulk Fill Flowable and Estelite Bulk Fill Flow). The following properties were examined according to ISO standard: flexural strength, flexural modulus, fracture toughness, water sorption, volumetric shrinkage, and depth of cure. Degree of conversion (DC%) was determined by FTIR spectrometry. A wear test was conducted with 15000 chewing cycles using a dual-axis chewing simulator. Wear depth was measured by a three-dimensional (3D) noncontact optical profilometer. Scanning electron microscopy was used to evaluate the microstructure of SFRC. Data were statistically analyzed with analysis of variance ANOVA (p = 0.05). SFRC exhibited the highest fracture toughness (2.8 MPa m1/2) and flexural strength (146.5 MPa) values (p < 0.05) and the greatest depth of cure (5 mm) and lowest wear depth (18.2 µm) among the flowable bulk fill materials tested. SDR showed the lowest volumetric shrinkage percentage (2.9%), while the other resin composites had comparable volumetric shrinkage values (p > 0.05). The new short fiber-reinforced flowable resin composite differed significantly in its measured fracture toughness compared to the tested flowable bulk fill resin composites.

Effect of Long-Term Brushing on Deflection, Maximum Load, and Wear of Stainless Steel Wires and Conventional and Spot Bonded Fiber-Reinforced Composites.

Fiber-reinforced composite (FRC) retainers are an aesthetic alternative to conventional Stainless Steel splints. They are generally used with a full bonded technique, but some studies demonstrated that they could be managed with a spot bonding technique to significantly decrease their rigidity. In order to propose this FRC spot bonding technique for clinical use, the aim of this study was to evaluate mechanical properties and surface wear of fibers left uncovered. Tests were made by simulating tooth brushing, comparing FRC spot bonding technique splints with stainless steel and FRC traditional technique splints. Specimens were tested both at 0.1 mm of deflection and at maximum load, showing higher values of rigidity for the FRC full bonded technique. After tooth brushing, no significant reduction in values at 0.1 mm deflection was reported, while we found a similar reduction in these values for the Stainless Steel and FRC spot bonding technique at maximum load, and no significant variation for the FRC full bonded technique. SEM images after tooth brushing showed wear for FRC fibers left uncovered, while no relevant wear signs in metal and conventional FRC fibers were noticed. Results showed that FRC spot bonding technique has advantages in mechanical properties when compared to the FRC traditional full bonding technique, also after tooth brushing. However, the surface wear after tooth brushing in the FRC spot bonding technique is considerable and other tests must be performed before promoting this technique for routine clinical use.

Fatigue resistance of a simulated single LOCATOR overdenture system.

STATEMENT OF PROBLEM: The incidence of fracture in a single-implant overdenture base increases in the region adjacent to the fulcrum implant. PURPOSE: The purpose of this in vitro study was to evaluate the effect of bidirectional woven electrical glass (E-glass) fiber reinforcements on the fatigue resistance of a simulated single LOCATOR-retained overdenture. MATERIAL AND METHODS: Test specimens with a centrally positioned metal housing for a LOCATOR stud attachment were fabricated from autopolymerizing acrylic resin. Specimens for the control group were fabricated without glass fiber reinforcements. The 4L group specimens had 4 layers of E-glass fiber weaves and were divided according to the fiber location into the following 3 subgroups: 4L-A with 4 fiber layers above the metal housing; 4L-N with 4 fiber layers adjacent to the metal housing; and 4L-A+4L-N with 4 fiber layers above and 4 fiber layers adjacent to the housing. Specimens were stored in distilled water for 1 week at 23 °C before cyclic fatigue testing at 10 000 cycles by using a staircase approach (n=12). The results were analyzed with 1-way ANOVA and the Tukey multiple comparisons post hoc analysis (α=.05). A 2-way ANOVA (α=.05) was conducted to detect the effect of fatigue cyclic loading and the position of the fiber layers and their interaction on the fatigue resistance. RESULTS: The results of the investigated compressive fatigue limits for the test groups were 190 ±15.9 N for the control group, 265 ±15.9 N for the 4L-A subgroup, 220 ±15.9 N for the 4L-N subgroup, and 275 ±15.9 N for the 4L-A+4L-N subgroup. A nonsignificant difference was found for creep values between the control group and reinforced subgroups (P>.05). The postfatigue flexural strength values in the 4L-A and 4L-A+4L-N subgroups were significantly higher than those in the control group (P<.001) and the 4L-N subgroup (P=.004 and P=.005). However, no significant difference was found in postfatigue flexural strength between the control group and the 4L-N subgroup (P=.828). CONCLUSIONS: Placing 4 layers of bidirectional E-glass fiber weaves above the metal housing can increase the fatigue resistance and the postfatigue flexural strength of single LOCATOR-retained overdentures.

From body-on-frame to unibody constructions and designs mimicking biological structures - an overview.

In dentistry, isotropic materials, such as metals, ceramics, and polymers, are used. Their properties are not related to any specific direction of the material microstructure. There is a trend toward non-metallic, adhesive, and minimally invasive dentistry. This is in line with the conceptual change seen in the automobile industry, in which the basis of car structures has changed from body-on-frame designs to unibody designs. In unibody designs, all structural parts of the body of the car mechanically form a single structural entity. In modern adhesive dentistry, remaining tooth substance and the dental material form unibody designs, enabling preservation of tooth substance. Biological structures are created to withstand loading and are light in weight. The structural designs of elements in these biological materials are, to a large extent, based on fibrous material. More attention has been paid to mimicking fibrous structures of dental hard tissues by synthetic fiber-reinforced composites. This overview reports key features of natural fibrous elements and how they are utilized in dentistry. Special emphasis is placed on the aspects of interfacial adhesion of restorative materials, especially ceramics to resin-based materials and their role in the unibody design of the tooth-restoration system.

Comparison of Load-Bearing Capacities of 3-Unit Fiber-Reinforced Composite Adhesive Bridges with Different Framework Designs.

BACKGROUND The aim of this study was to investigate and compare the load-bearing capacities of three-unit direct resin-bonded fiber-reinforced composite fixed dental prosthesis with different framework designs. MATERIAL AND METHODS Sixty mandibular premolar and molar teeth without caries were collected and direct glass fiber-resin fixed FDPs were divided into 6 groups (n=10). Each group was restored via direct technique with different designs. In Group 1, the inlay-retained bridges formed 2 unidirectional FRC frameworks and pontic-reinforced transversal FRC. In Group 2, the inlay-retained bridges were supported by unidirectional lingual and occlusal FRC frameworks. Group 3, had buccal and lingual unidirectional FRC frameworks without the inlay cavities. Group 4 had reinforced inlay cavities and buccal-lingual FRC with unidirectional FRC frameworks. Group 5, had a circular form of fiber reinforcement around cusps in addition to buccal-lingual FRC frameworks. Group 6 had a circular form of fiber reinforcement around cusps with 2 bidirectional FRC frameworks into inlay cavities. All groups were loaded until final fracture using a universal testing machine at a crosshead speed of 1 mm/min. RESULTS Mean values of the groups were determined with ANOVA and Tukey HSD. When all data were evaluated, Group 6 had the highest load-bearing capacities and revealed significant differences from Group 3 and Group 4. Group 6 had the highest strain (p>0.05). When the fracture patterns were investigated, Group 6 had the durability to sustain fracture propagation within the restoration. CONCLUSIONS The efficiency of fiber reinforcement of the restorations alters not only the amount of fiber, but also the design of the restoration with fibers.