Thermo-elastic gigahertz-frequency oscillator through surface acoustic wave-silicon photonics.

Opto-electronic oscillators are sources of microwave-frequency tones that may reach very low noise levels. Much effort is being dedicated to the realization of oscillators based on photonic integrated devices. In this work, we propose and demonstrate a thermo-elastic opto-electronic oscillator at 2.213 GHz frequency based on a standard silicon-photonic integrated circuit. A microwave-frequency electrical signal modulates an optical pump wave carrier. The modulated waveform launches surface acoustic waves in a silicon-on-insulator substrate, through absorption in a metallic grating and thermo-elastic actuation. The waveform is reconverted to the optical domain through photoelastic modulation of an optical probe wave carrier in a standard racetrack resonator waveguide. Both the thermo-elastic actuation and the photoelastic modulation are radio-frequency selective. The output probe wave is detected, and the receiver voltage is amplified and fed back to modulate the optical pump input. Sufficient gain drives the loop into oscillations. The oscillator does not involve piezoelectricity and can be realized on any substrate. Long acoustic delays may be implemented in compact devices. The frequency of operation is scalable to tens of GHz. The principle may be useful in integrated microwave-photonic signal processing and in the elastic analysis of surfaces and thin layers.

Measuring glass transition of a polymer coating layer over working fiber using forward Brillouin scattering.

The glass transition temperature is a key parameter of polymer coating layers that protect optical fibers, and it affects the proper function of the fibers in their service environment. Established protocols for glass transition temperature measurements are destructive, require samples of specific geometries, and may only be carried out offline. In this work, we report the nondestructive measurement of the glass transition temperature of an acrylate polymer coating layer over a working standard fiber. The method is based on forward stimulated Brillouin scattering. A large decrease in the modulus of the coating layer above the glass transition temperature manifests in the narrowing of the modal linewidths in the forward Brillouin scattering spectrum. The transition temperature agrees with the standard dynamic mechanical analysis of samples made of the same polymer. The protocol can be useful for coating materials research and development, production line quality assurance, and preventive maintenance.

Analysis of thin layers using surface acoustic wave-photonic devices in silicon-on-insulator.

The analysis of thin layers deposited on various substrates is widely employed in thickness monitoring, materials research and development and quality control. Measurements are often performed based on changes to acoustic resonance frequencies of quartz micro-balance devices. The technique is extremely sensitive, but it is restricted to hundreds of MHz frequencies and requires electrical connectivity. In this work we propose and demonstrate the analysis of elastic properties of thin layers deposited on surface acoustic wave-photonic devices in standard silicon-on-insulator. The devices operate at 2.4 GHz frequency, and their interfaces are fiber-optic. The radio-frequency transfer functions of the devices are modified by sub-percent level changes to the group velocity of surface acoustic waves following deposition of layers. Layers of aluminum oxide and germanium sulfide of thickness between 10-80 nm are characterized. The analysis provides estimates for Young's modulus of the layers.

Optical fiber point sensors based on forward Brillouin scattering.

Forward Brillouin scattering interactions support the sensing and analysis of media outside the cladding boundaries of standard fibers, where light cannot reach. Quantitative point-sensing based on this principle has yet to be reported. In this work, we report a forward Brillouin scattering point-sensor in a commercially available, off-the-shelf multi-core fiber. Pump light at the inner, on-axis core of the fiber is used to stimulate a guided acoustic mode of the entire fiber cross-section. The acoustic wave, in turn, induces photoelastic perturbations to the reflectivity of a Bragg grating inscribed in an outer, off-axis core of the same fiber. The measurements successfully analyze refractive index perturbations on the tenth decimal point and distinguish between ethanol and water outside the centimeter-long grating. The measured forward Brillouin scattering linewidths agree with predictions. The acquired spectra are unaffected by forward Brillouin scattering outside the grating region. The results add point-analysis to the portfolio of forward Brillouin scattering optical fiber sensors.

Brillouin Optical Correlation Domain Analysis in Composite Material Beams.

Structural health monitoring is a critical requirement in many composites. Numerous monitoring strategies rely on measurements of temperature or strain (or both), however these are often restricted to point-sensing or to the coverage of small areas. Spatially-continuous data can be obtained with optical fiber sensors. In this work, we report high-resolution distributed Brillouin sensing over standard fibers that are embedded in composite structures. A phase-coded, Brillouin optical correlation domain analysis (B-OCDA) protocol was employed, with spatial resolution of 2 cm and sensitivity of 1 °K or 20 micro-strain. A portable measurement setup was designed and assembled on the premises of a composite structures manufacturer. The setup was successfully utilized in several structural health monitoring scenarios: (a) monitoring the production and curing of a composite beam over 60 h; (b) estimating the stiffness and Young's modulus of a composite beam; and (c) distributed strain measurements across the surfaces of a model wing of an unmanned aerial vehicle. The measurements are supported by the predictions of structural analysis calculations. The results illustrate the potential added values of high-resolution, distributed Brillouin sensing in the structural health monitoring of composites.

Double-pulse pair Brillouin optical correlation-domain analysis.

Brillouin optical correlation-domain analysis (B-OCDA) allows for distributed measurements of strain and temperature with sub-cm resolution. Time-multiplexing techniques have previously extended B-OCDA to the monitoring of many km of fiber and two million resolution points. Thus far, however, the number of scans of correlation peaks positions, necessary to cover the fiber under test, was restricted to the order of 100 or more. In this work we report a B-OCDA protocol that is able to address an entire fiber using only 11 pairs of position scans per choice of frequency. The measurements protocol relies on a merger between B-OCDA principles and double-pulse-pair analysis, previously incorporated in time-domain Brillouin sensors. Phase coding of the pump and signal waves with a repeating, short and high-rate code stimulates Brillouin interactions in a large number of narrow correlation peaks, with substantial temporal overlap. Unambiguous measurements are achieved by repeating each experiment twice, using a pair of pump pulses of different durations, and subtracting the two output traces. The principle is demonstrated in the analysis of a 43 m-long fiber with 2.7 cm resolution. Several local hot-spots are properly identified in the measurements. The experimental uncertainty in the measurement of the local Brillouin frequency shift is estimated as ± 1.9 MHz. The proposed method requires broader detection bandwidth and a larger number of averages than those of previous time-gated B-OCDA setups. Hence the overall number of measurements is similar to that of previous setups.

High-resolution Brillouin optical correlation domain analysis with no spectral scanning.

Distributed Brillouin fiber sensors typically rely on the reconstruction of the steady-state Brillouin gain spectrum (BGS), through spectral scanning of the frequency offset between the pump and signal waves. In this work, we propose and demonstrate an alternative approach, in which the local Brillouin frequency shift (BFS) is extracted from temporal transient analysis of the step response of the amplified signal wave. Measurements are taken at only two arbitrary frequency offsets between pump and signal. No spectral scanning and no prior knowledge of a reference BGS are necessary. The principle is supported by analytic and numeric solutions of the differential equations of stimulated Brillouin scattering. The BFS of a 2 meters-long fiber under test was measured with 1 MHz accuracy and a dynamic range of 200 MHz. Transient measurements were also performed in a Brillouin optical correlation domain analysis (B-OCDA) experiment with 4 cm resolution, standard deviation of 2.4 MHz and 100 MHz dynamic range. A 4 cm-wide hot-spot was properly identified in the measurements. Multiple correlation peaks could be addressed in a single flight of a pump pulse. The results represent the first B-OCDA that is free of spectral scanning. This new measurement concept may be applicable to random-access distributed and dynamic monitoring of sound and vibration.

High-resolution long-reach distributed Brillouin sensing based on combined time-domain and correlation-domain analysis.

A new scheme for distributed Brillouin sensing of strain and temperature in optical fibers is proposed, analyzed and demonstrated experimentally. The technique combines between time-domain and correlation-domain analysis. Both Brillouin pump and signal waves are repeatedly co-modulated by a relatively short, high-rate phase sequence, which introduces Brillouin interactions in a large number of discrete correlation peaks. In addition, the pump wave is also modulated by a single amplitude pulse, which leads to a temporal separation between the generation of different peaks. The Brillouin amplification of the signal wave at individual peak locations is resolved in the time domain. The technique provides the high spatial resolution and long range of unambiguous measurement offered by correlation-domain Brillouin analysis, together with reduced acquisition time through the simultaneous interrogation of a large number of resolution points. In addition, perfect Golomb codes are used in the phase modulation of the two waves instead of random sequences, in order to reduce noise due to residual, off-peak Brillouin interactions. The principle of the method is supported by extensive numerical simulations. Using the proposed scheme, the Brillouin gain spectrum is mapped experimentally along a 400 m-long fiber under test with a spatial resolution of 2 cm, or 20,000 resolution points, with only 127 scans per choice of frequency offset between pump and signal. Compared with corresponding phase-coded, Brillouin correlation domain analysis schemes with equal range and resolution, the acquisition time is reduced by a factor of over 150. A 5 cm-long hot spot, located towards the output end of the pump wave, is properly identified in the measurements. The method represents a significant advance towards practical high-resolution and long range Brillouin sensing systems.

Brillouin optical correlation domain analysis with 4 millimeter resolution based on amplified spontaneous emission.

A new technique for Brillouin scattering-based, distributed fiber-optic measurements of temperature and strain is proposed, analyzed, simulated, and demonstrated. Broadband Brillouin pump and signal waves are drawn from the filtered amplified spontaneous emission of an erbium-doped fiber amplifier, providing high spatial resolution. The reconstruction of the position-dependent Brillouin gain spectra along 5 cm of a silica single-mode fiber under test, with a spatial resolution of 4 mm, is experimentally demonstrated using a 25 GHz-wide amplified spontaneous emission source. A 4 mm-long localized hot spot is identified by the measurements. The uncertainty in the reconstruction of the local Brillouin frequency shift is ± 1.5 MHz. The single correlation peak between the pump and signal is scanned along a fiber under test using a mechanical variable delay line. The analysis of the expected spatial resolution and the measurement signal-to-noise ratio is provided. The measurement principle is supported by numerical simulations of the stimulated acoustic field as a function of position and time. Unlike most other Brillouin optical correlation domain analysis configurations, the proposed scheme is not restricted by the bandwidth of available electro-optic modulators, microwave synthesizers, or pattern generators. Resolution is scalable to less than one millimeter in highly nonlinear media.

High-resolution long-range distributed Brillouin analysis using dual-layer phase and amplitude coding.

A new, hybrid time-domain and correlation-domain Brillouin analysis technique is proposed and demonstrated, providing a large number of high-resolution acquisition points. The method is based on dual-layer hierarchal encoding of both amplitude and phase. The pump and signal waves are co-modulated by a relatively short, high-rate binary phase sequence. The phase modulation introduces Brillouin interactions in a large number of discrete and localized correlation peaks along the fiber under test. In addition, the pump wave is also amplitude-modulated by a slower, carefully synthesized, long on-off-keying sequence. Brillouin interactions at the correlation peaks imprint weak replicas of the pump amplitude sequence on the intensity of the output signal wave. The Brillouin amplifications at individual correlation peaks are resolved by radar-like, matched-filter processing of the output signal, following a recently-proposed incoherent compression protocol. The method provides two significant advantages with respect to previous, pulse-gated correlation-domain analysis schemes, which involved a single pump pulse. First, compression of the extended pulse sequence enhances the measurement signal-to-noise ratio, which is equivalent to that of a large number of averages over repeating single-pulse acquisitions. The acquisition times are potentially much reduced, and the number of resolution points that may be practically interrogated increases accordingly. Second, the peak power level of the pump pulses may be lowered. Hence, the onset of phase pattern distortion due to self-phase modulation is deferred, and the measurement range can be increased. Using the proposed method, the acquisition of Brillouin gain spectra over a 2.2 km-long fiber with a spatial resolution of 2 cm is demonstrated experimentally. The entire set of 110,000 resolution points is interrogated using only 499 position scans per choice of frequency offset between pump and signal. A 5 cm-long hot-spot, located towards the output end of the pump wave, is properly recognized in the measurements.

Tunable microwave-photonic filter using frequency-to-time mapping-based delay lines.

A new implementation of microwave-photonic filters (MPFs) based on tunable optical delay lines is proposed and demonstrated. The variable delay is based on mapping of the spectral components of an incoming waveform onto the time domain, the application of linearly-varying temporal phase offsets, and an inverse mapping back to the frequency domain. The linear phase correction is equivalent to a frequency offset, and realized though suppressed-carrier single-sideband modulation by a radio-frequency sine wave. The variable delay element, controlled by the selected frequency, is used in one arm of a two-tap MPF. In a proof-of-concept experiment, the free spectral range (FSR) of the MPF was varied by over a factor of four: between 1.2 GHz and 5.3 GHz.

Generation of ultra-narrow, stable and tunable millimeter- and terahertz- waves with very low phase noise.

The interference between two spectral lines of the frequency comb of a fiber femtosecond laser is used to generate millimeter-wave and terahertz tones. The two lines are selected by stimulated Brillouin scattering (SBS) amplification. All other modes are strongly rejected based on polarization discrimination, using the polarization-pulling effect that is associated with SBS. The inherent high spectral quality of a femtosecond fiber laser comb allows generation of millimeter- and terahertz waves with linewidths below 1 Hz, and a phase noise of -105 dBc/Hz at 10 kHz offset. The generation, free-space transmission and detection of continuous waves at 1 THz are demonstrated as well. Lastly, the generated millimeter-wave carriers are modulated by 40 Gbit/s data. The entire system consists of a fiber laser and standard equipment of optical telecommunications. Besides metrology, spectroscopy and astronomy, the method can be utilized for the emergent field of wireless millimeter-wave and THz-communications at ultra-high data rates.

Experimental demonstration of localized Brillouin gratings with low off-peak reflectivity established by perfect Golomb codes.

Dynamic Brillouin gratings (DBGs), inscribed by comodulating two writing pump waves with a perfect Golomb code, are demonstrated and characterized experimentally. Compared with pseudo-random bit sequence (PRBS) modulation of the pump waves, the Golomb code provides lower off-peak reflectivity due to the unique properties of its cyclic autocorrelation function. Golomb-coded DBGs allow the long variable delay of one-time probe waveforms with higher signal-to-noise ratios, and without averaging. As an example, the variable delay of return-to-zero, on-off keyed data at a 1 Gbit/s rate, by as much as 10 ns, is demonstrated successfully. The eye diagram of the reflected waveform remains open, whereas PRBS modulation of the pump waves results in a closed eye. The variable delay of data at 2.5 Gbit/s is reported as well, with a marginally open eye diagram. The experimental results are in good agreement with simulations.

Brillouin optical spectrum analyzer monitoring of subcarrier-multiplexed fiber-optic signals.

Optical spectral analysis of closely spaced, subcarrier multiplexed fiber-optic transmission is performed, based on stimulated Brillouin scattering (SBS). The Brillouin gain window of a single, continuous-wave pump is scanned across the spectral extent of the signal under test. The polarization pulling effect associated with SBS is employed to improve the rejection ratio of the analysis by an order of magnitude. Ten tones, spaced by only 10 MHz and each carrying random-sequence on-off keying data, are clearly resolved. The measurement identifies the absence of a single subcarrier, directly in the optical domain. The results are applicable to the monitoring of optical orthogonal frequency domain multiplexing and radio over fiber transmission.

Monitoring the evaporation of fluids from fiber-optic micro-cell cavities.

Fiber-optic sensors provide remote access, are readily embedded within structures, and can operate in harsh environments. Nevertheless, fiber-optic sensing of liquids has been largely restricted to measurements of refractive index and absorption spectroscopy. The temporal dynamics of fluid evaporation have potential applications in monitoring the quality of water, identification of fuel dilutions, mobile point-of-care diagnostics, climatography and more. In this work, the fiber-optic monitoring of fluids evaporation is proposed and demonstrated. Sub-nano-liter volumes of a liquid are applied to inline fiber-optic micro-cavities. As the liquid evaporates, light is refracted out of the cavity at the receding index boundary between the fluid and the ambient surroundings. A sharp transient attenuation in the transmission of light through the cavity, by as much as 50 dB and on a sub-second time scale, is observed. Numerical models for the transmission dynamics in terms of ray-tracing and wavefront propagation are provided. Experiments show that the temporal transmission profile can distinguish between different liquids.

Enhancement of spectral resolution and optical rejection ratio of Brillouin optical spectral analysis using polarization pulling.

High-resolution, wide-bandwidth optical spectrum analysis is essential to the measuring and monitoring of advanced optical, millimeter-wave, and terahertz communication systems, sensing applications and device characterization. One category of high-resolution spectrum analyzers reconstructs the power spectral density of a signal under test by scanning a Brillouin gain line across its spectral extent. In this work, we enhance both the resolution and the optical rejection ratio of such Brillouin-based spectrometers using a combination of two techniques. First, two Brillouin loss lines are superimposed upon a central Brillouin gain to reduce its bandwidth. Second, the vector attributes of stimulated Brillouin scattering amplification in standard, weakly birefringent fibers are used to change the signal state of polarization, and a judiciously aligned output polarizer discriminates between amplified and un-amplified spectral contents. A frequency resolution of 3 MHz, or eight orders of magnitude below the central optical frequency, is experimentally demonstrated. In addition, a weak spectral component is resolved in the presence of a strong adjacent signal, which is 30 dB stronger and detuned by only 60 MHz. The measurement method involves low-bandwidth direct detection, and does not require heterodyne beating. The measurement range of the proposed method is scalable to cover the C + L bands, depending on the tunable pump source. The accuracy of the measurements requires that the pump frequencies are well calibrated.

Low-noise delays from dynamic Brillouin gratings based on perfect Golomb coding of pump waves.

A method for long variable all-optical delay is proposed and simulated, based on reflections from localized and stationary dynamic Brillouin gratings (DBGs). Inspired by radar methods, the DBGs are inscribed by two pumps that are comodulated by perfect Golomb codes, which reduce the off-peak reflectivity. Compared with random bit sequence coding, Golomb codes improve the optical signal-to-noise ratio (OSNR) of delayed waveforms by an order of magnitude. Simulations suggest a delay of 5 Gb/s data by 9 ns, or 45 bit durations, with an OSNR of 13 dB.

Stimulated Brillouin scattering amplification in centimeter-long directly written chalcogenide waveguides.

Stimulated Brillouin scattering (SBS) amplification is obtained in directly written As2S3 channel waveguides. Centimeter-long waveguides were written using a Ti:sapphire femtosecond laser, operating at a central wavelength of 810 nm. The cross-section of the waveguides was of 4 µm×1 µm. A Brillouin frequency shift of 7.5 GHz is observed, in general agreement with corresponding previous studies. The SBS gain spectrum in the short waveguides is comparatively broad, with a full width at half-maximum of 200 MHz. We attribute the broad linewidth to the spatial evolution of the electromagnetic field profile along the waveguide.

Continuously variable long microwave-photonic delay of arbitrary frequency-chirped signals.

A generic method for the continuously variable, long microwave-photonic delay of the impulse response of arbitrarily chirped waveforms is proposed and demonstrated. Nonlinear-frequency-modulated waveforms of 500 MHz bandwidth are delayed by tens of nanoseconds. The principle relies on the specific phase-time relations of the waveforms, and is applicable to chirped pulses of arbitrary durations, central radio frequencies, and bandwidths. The approach is suitable for beam steering in large phased-array antennas.

A forward Brillouin fibre laser.

Fibre lasers based on backward stimulated Brillouin scattering provide narrow linewidths and serve in signal processing and sensing applications. Stimulated Brillouin scattering in fibres takes place in the forward direction as well, with amplification bandwidths that are narrower by two orders of magnitude. However, forward Brillouin lasers have yet to be realized in any fibre platform. In this work, we report a first forward Brillouin fibre laser, using a bare off-the-shelf, panda-type polarisation maintaining fibre. Pump light in one principal axis provides Brillouin amplification for a co-propagating lasing signal of the orthogonal polarisation. Feedback is provided by Bragg gratings at both ends of the fibre cavity. Single-mode, few-modes and multi-mode regimes of operation are observed. The lasing threshold exhibits a unique environmental sensitivity: it is elevated when the fibre is partially immersed in water due to the broadening of forward Brillouin scattering spectra. The results establish a new type of fibre laser, with potential for ultra-high coherence and precision sensing of media outside the cladding.