Biocomposite Cryogels for Photothermal Decontamination of Water.

An effective and sustainable approach to deal with the scarcity of freshwater is interfacial solar-driven evaporation. Nonetheless, some serious challenges for photothermal materials still need to be considered, such as long-term stability in harsh environments, eco-friendly materials, and cost-effective and simple fabrication processes. Keeping these points in mind, we present a multifunctional silver-coated vegetable waste biocomposite cryogel that not only exhibits high porosity and enhanced wettability and stability but also possesses high light absorption and low thermal conductivity favorable for heat localization, solar steam generation, and efficient photothermal conversion efficiency. The achieved solar evaporation rate is 1.17 kg m-2 h-1 with a solar-to-vapor conversion efficiency of 81.11% under 1 Sun irradiation. The developed material is able to effectively desalinate artificial seawater and decontaminate synthetic wastewater (e.g., water containing dye molecules and mercury ions) with an efficiency of >99%. Most importantly, the composite cryogel presents antifouling properties, and in particular, salt antifouling ability and anti-biofouling properties. Thus, the numerous functionalities of the biocomposite cryogel make it a cost-effective promising device for prolonged water decontamination processes.

Efficacy of erythritol powder air-polishing in active and supportive periodontal therapy: A systematic review and meta-analysis.

OBJECTIVE: This systematic review aimed to analyse available evidence to answer two focused questions about the efficacy of erythritol powder air-polishing (EPAP) (i) as an adjunctive during active periodontal therapy (APT) and (ii) as an alternative to hand/ultrasonic instrumentation during supportive periodontal therapy (SPT). Additionally, microbiological outcomes and patient's comfort/perceptions were assessed as secondary outcomes. METHODS: PubMed, Cochrane and Medline were searched for relevant articles published before February 2021 following PRISMA guidelines. The search was conducted by three independent reviewers, and the agreement was measured by Cohen's kappa score. Out of 1043 articles, eight randomized clinical trials were selected for systematic review and quantitative synthesis. Only periodontal parameters, such as clinical attachment level (CAL), probing pocket depth (PPD) and bleeding on probing (BoP), showed homogeneity and, thus, were selected for meta-analysis. RESULTS: The improvement in PPD and BoP scores after using EPAP was comparable with hand/ultrasonic instrumentation during both APT and SPT. Significant CAL gain was achieved with EPAP during APT (0.16 mm, p < 0.02) compared with hand/ultrasonic instrumentation at the end point, whereas non-significant CAL gain was achieved during SPT. No differences were observed regarding microbiological outcomes between the two treatment modalities. However, EPAP inflicted less pain and was better perceived by the patients. CONCLUSION: Erythritol powder air-polishing can substitute hand/ultrasonic instrumentation for SPT, and CAL gain is significantly improved when EPAP is used as an adjunct during APT. For microbiological outcomes, no significant differences were observed between the two approaches; however, EPAP was better tolerated by the patients than hand/ultrasonic instrumentation. CLINICAL RELEVANCE: Erythritol powder air-polishing can be used as an adjunct during APT and as an alternative to conventional mechanical debridement during SPT.

Assessment of factors influencing oral health-related quality of life (OHRQoL) of patients with removable dental prosthesis.

OBJECTIVE: The aim of this study was to evaluate factors affecting oral health related quality of life (OHRQoL) of patients using removable dental prosthesis. METHODS: The present study employed a cross sectional analytical design. A total of 200 patients participated and interviewed using a cross sectional analytical design. In the first section of the questionnaire patients were asked about demographic data whereas the second part of the questionnaire assessed medical history, oral habits, smoking status, oral hygiene habits and frequency of dental visit. The questionnaire also collected information regarding patient's removable prosthesis. Questionnaire of OHIP-DENT (Oral Health Impact Profile) was also employed to measure oral health quality of life (OHRQoL) on the domains of functional limitation (FL), physical pain (P1), psychological discomfort (P2), physical disability (D1), psychological disability (D2), social disability (D3) and handicap (H). Relationships between the demographic, socio-economic and education variables and others OHIP-EDENT scores were explored by comparing mean scores by applying ANOVA. RESULTS: The study participants comprised of 107 males (53.5%) and 93 females (46.5%). Regarding oral care, participants reporting to visit their dentist within one year were 40.0%. The highest score was recorded for the functional limitation (FL) domain (15.62±6.6), followed by social disability (D3) (15.23±5.06) and physical pain (P1) (14.28±4.8). The respective scores for physical (D1) and psychological disability (D2) and handicap (H) were 10.47±4.84, 11.32±5.38 and 12.45±4.50 respectively. CONCLUSIONS: Removable partial denture patients showed minimum problems with mastication, social compromise and functional discomfort. The oral health quality of life of removable denture patients is significantly influenced by patient education level, socio-economic status, medical conditions, smoking and tobacco use habits.

Electrospinning of Chitosan-Based Solutions for Tissue Engineering and Regenerative Medicine.

Electrospinning has been used for decades to generate nano-fibres via an electrically charged jet of polymer solution. This process is established on a spinning technique, using electrostatic forces to produce fine fibres from polymer solutions. Amongst, the electrospinning of available biopolymers (silk, cellulose, collagen, gelatine and hyaluronic acid), chitosan (CH) has shown a favourable outcome for tissue regeneration applications. The aim of the current review is to assess the current literature about electrospinning chitosan and its composite formulations for creating fibres in combination with other natural polymers to be employed in tissue engineering. In addition, various polymers blended with chitosan for electrospinning have been discussed in terms of their potential biomedical applications. The review shows that evidence exists in support of the favourable properties and biocompatibility of chitosan electrospun composite biomaterials for a range of applications. However, further research and in vivo studies are required to translate these materials from the laboratory to clinical applications.

Functional material features of Bombyx mori silk light versus heavy chain proteins.

Bombyx mori (BM) silk fibroin is composed of two different subunits: heavy chain and light chain fibroin linked by a covalent disulfide bond. Current methods of separating the two silk fractions is complicated and produces inadequate quantities of the isolated components for the study of the individual light and heavy chain silks with respect to new materials. We report a simple method of separating silk fractions using formic acid. The formic acid treatment partially releases predominately the light chain fragment (soluble fraction) and then the soluble fraction and insoluble fractions can be converted into new materials. The regenerated original (total) silk fibroin and the separated fractions (soluble vs insoluble) had different molecular weights and showed distinctive pH stabilities against aggregation/precipitation based on particle charging. All silk fractions could be electrospun to give fiber mats with viscosity of the regenerated fractions being the controlling factor for successful electrospinning. The silk fractions could be mixed to give blends with different proportions of the two fractions to modify the diameter and uniformity of the electrospun fibers formed. The soluble fraction containing the light chain was able to modify the viscosity by thinning the insoluble fraction containing heavy chain fragments, perhaps analogous to its role in natural fiber formation where the light chain provides increased mobility and the heavy chain producing shear thickening effects. The simplicity of this new separation method should enable access to these different silk protein fractions and accelerate the identification of methods, modifications, and potential applications of these materials in biomedical and industrial applications.

Attitudes, knowledge, and perceptions of dentists and dental students toward artificial intelligence: a systematic review.

Objectives: This research was aimed at assessing comprehension, attitudes, and perspectives regarding artificial intelligence (AI) in dentistry. The null hypothesis was a lack of foundational understanding of AI in dentistry. Methods: This systematic review following Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines was conducted in May 2023. The eligibility criteria included cross-sectional studies published in English until July 2023, focusing solely on dentists or dental students. Data on AI knowledge, use, and perceptions were extracted and assessed for bias risk with the Joanna Briggs Institute checklist. Results: Of 408 publications, 22 relevant articles were identified, and 13 studies were included in the review. The average basic AI knowledge score was 58.62 % among dental students and 71.75 % among dentists. More dental students (72.01 %) than dentists (62.60 %) believed in AI's potential for advancing dentistry. Conclusions: Thorough AI instruction in dental schools and continuing education programs for practitioners are urgently needed to maximize AI's potential benefits in dentistry. An integrated PhD program could drive revolutionary discoveries and improve patient care globally. Embracing AI with informed understanding and training will position dental professionals at the forefront of technological advancements in the field.

Effectiveness of H-files and Pro-Taper universal systems in removing Gutta-percha during endodontic retreatment: A comparative study.

Objective: This research was aimed at assessing the effectiveness of manual H-files versus a combination of a Pro-Taper universal rotary canal preparation system and retreatment system in removing gutta-percha (GP) during endodontic retreatment, by using a digital radiography technique. Methods: This ex vivo study used a non-probability consecutive sampling technique. The study sample comprised 60 extracted anterior permanent teeth, each with one root with a straight root canal (RC). After preparation, RCs were obturated with GP and sealer. Subsequently, teeth were stored for 2 weeks in a humid environment at 37 °C. Thirty teeth each were randomly assigned to the control (group I), and experimental (group II) groups. GP removal was performed with H-files {group I) or a combination of a Pro-Taper universal rotary canal preparation system and retreatment system (group 2). Digital radiographs were acquired with Carestream digital radiovisiography software (Kodak; version-VER.6.10.8.3-A), and the presence of residual GP was analyzed. AutoCAD (2006) software was used to demarcate the RC and residual root filling. The residual GP in both groups was compared with independent sample t-tests. Results: The remaining root filling did not significantly differ when GP was removed with conventional Hedstrom files versus a combination of Pro-Taper Universal preparation and retreatment file systems. The residual GP was confined to the apical third of the canals in both groups. Conclusions: Pro-Taper Universal preparation and retreatment file systems have similar effectiveness to manual H-files in GP removal in straight canals.

Effects of metformin on the bioactivity and osseointegration of dental implants: A systematic review.

Dental implants are prosthetic devices that are surgically placed in direct contact with the jawbone to support intra-oral functions and esthetics. Diabetes mellitus may contribute to peri-implant bone loss. During the last few years, there have been attempts to reduce this bone loss and improve the survival rate of implants. Metformin, an anti-diabetic drug known for its osteogenic properties, is thought to prevent peri-implant bone loss in diabetic patients. Although several studies have been conducted to study metformin's effect on diabetic and non-diabetic study models, no systematic review has analyzed and summarized these studies critically. Therefore, the objectives of this systematic review were to summarize the outcomes of these studies and critically appraise them. Seven studies were included in this systematic review. Four studies used only animal models, two used both animal and cell culture models, and one used only cell culture studies. The general characteristics and outcomes of the included studies were summarized, and Animal Research: Reporting of In Vivo Experiments (ARRIVE) guidelines were used to assess the quality of the animal studies. In vitro studies indicate that metformin may induce stem cells to undergo osteoblastic differentiation to produce a higher amount of bone and may also improve osseointegration. Nevertheless, several studies had potential sources of bias. Therefore, it is recommended that emphasis be placed on increasing the quality of future animal studies and human trials to determine the effects of metformin on the osseointegration of dental implants. Future studies are needed with adequate follow-up to evaluate the efficacy of metformin in improving the osseointegration of dental implants.

Literature search strategies in dental education and research.

A well-organized literature search is a fundamental requirement for research-based dental education. The execution of a literature search is not beneficial unless researchers possess basic knowledge about it. In this article, all basic strategies and research tools essentially required for a literature search, including Boolean operators, correct use of keywords, database selection, and the evaluation of filtered data and limitations, are discussed. The present article offers vital information and literature search guidelines for early career dental researchers and dental students. In addition, it contains a collection of all the essential information related to the generally used electronic databases in dentistry research. This will be helpful for dental students, residents, consultants, and allied science researchers.

Source Imaging of Triphasic Waves and Other Encephalopathies.

PURPOSE: Triphasic waves (TWs) are defined as high-amplitude positive waveforms with preceding and after-going negative waves, typically seen in medically ill patients. TWs manifest in similar clinical presentations as other EEG encephalopathies; however, electrographically, they appear different. To better understand the difference, the authors used two different source localization software programs to find a reproducible and unique signature for TW. METHODS: EEGs performed at Johns Hopkins Hospital and Duke University Hospital were retrospectively analyzed. EEG samples of TW, Delta, Theta-Delta, and Frontal Intermittent Rhythmic Delta Activity were selected. The authors did source localization via Commercial Curry 8 and open-source Brainstorm software. A minimum of 10 stereotypical waveforms per subject were selected. The authors used the Boundary Element Method for the head model, which was derived from the Montreal Neurological Institute averaged imaging data set. Dipole and current density analyses were performed. RESULTS: Twenty-eight patients were selected (10 TW, 4 Frontal Intermittent Rhythmic Delta Activity, 6 Theta-Delta, and 8 Delta). The findings suggest the activation of anterior frontal and midline structures for TW. Frontal Intermittent Rhythmic Delta Activity had a similar localization but without a moving dipole. In comparison, the Delta and Delta-Theta appeared to have a more diffuse origin. CONCLUSIONS: Source analysis of TW via two different software suggests the anterior midline location of TW with anterior to posterior propagation. These findings correlate with the previous hypotheses of TW origin. Retrospective analysis, low number of recording electrodes, and difficult analysis of slow waves limit the interpretation of these results. Nonetheless, this article opens the prospect of future studies in this field.

Biochemical analysis of oral fluids for disease detection.

The field of diagnostics using invasive blood testing represents the majority of diagnostic tests used as part of routine health monitoring. The relatively recent introduction of salivary diagnostics has lead to a major paradigm shift in diagnostic analyses. Additionally, in this era of big data, oral fluid testing has shown promising outcomes in a number of fields, particularly the areas of genomics, microbiomics, proteomics, metabolomics, and transcriptomics. Despite the analytical challenges involved in the interpretation of large datasets generated from biochemical studies involving bodily fluids, including saliva, many studies have identified novel oral biomarkers for diagnosing oral and systemic diseases. In this regard, oral biofluids, including saliva, gingival crevicular fluid (GCF), peri-implant crevicular fluid (PICF), dentinal tubular fluid (DTF), are now attracting increasing attention due to their important attributes, such as noninvasive sampling, easy handling, low cost, and more accurate diagnosis of oral diseases. Recently, the utilization of salivary diagnostics to evaluate systemic diseases and monitor general health has increased in popularity among clinicians. Saliva contains a wide range of protein, DNA and RNA biomarkers, which assist in the diagnosis of multiple diseases and conditions, including cancer, cardiovascular diseases (CVD), auto-immune and degenerative diseases, respiratory infections, oral diseases, and microbial (viral, bacterial and fungal) diseases. Moreover, due to its noninvasive nature and ease-of-adoption by children, it is now being used in mass screening programs, oral health-related studies and clinical trials in support of the development of therapeutic agents. The recent advent of highly sensitive technologies, such as next-generation sequencing, mass spectrometry, highly sensitives ELISAs, and homogeneous immunoassays, suggests that even small quantities of salivary biomarkers are able to be assayed accurately, providing opportunities for the development of many future diagnostic applications (including emerging technologies, such as point-of-care and rapid molecular technologies). The present article explores the omics and biochemical compositions of various oral biofluids with important value in diagnostics and monitoring.

COVID-19 Pandemic and Role of Human Saliva as a Testing Biofluid in Point-of-Care Technology.

Novel coronavirus disease 2019 (COVID-19) outbreak has termed as a controllable pandemic, and the entire world has come to a standstill trying to mitigate the disease with health systems. Health care providers, around the globe, are fighting day and night. Currently, rapid testing is taking place with the help of nasopharyngeal, oropharyngeal swab, bronchoalveolar lavage, sputum, urine, and blood. All these approaches are invasive or embarrassing to the infected person. It is observed that salivary glands are hosting severe acute respiratory syndrome-coronavirus-2 (SARS-CoV-2) because of angiotensin-converting enzyme 2 and the detection of high viral loads in the saliva and is playing a crucial role in virus transmission, especially from individuals showing absolutely no symptoms. Saliva is proving to be a promising noninvasive sample specimen for the diagnosis of COVID-19, thus helping to monitor the infection and prevent it from further spreading by prompt isolation.

Evaluating antibacterial and surface mechanical properties of chitosan modified dental resin composites.

BACKGROUND: The antibacterial properties are beneficial and desired for dental restorative composite materials. The incorporation of various antimicrobial agents into resin composites may compromise their physical and mechanical properties hence limiting their applications. OBJECTIVE: The aim of the current study is to evaluate the antibacterial activity and the hardness of microhybrid and flowable resin based composites (RBCs) modified using novel antimicrobial agent chitosan (CS). METHODS: The antibacterial activity of microhybrid and flowable RBCs modified with 0, 0.25, 0.5 and 1% w/w chitosan (CS) against Actinomyces viscous bacteria was explored using agar diffusion test and direct contact methods. The hardness of control and experimental RBCs was determined by Vickers hardness (VH) tester. RESULTS: The results revealed that control and experimental flowable and microhybrid RBCs did not demonstrate growth inhibition zone in the lawn growth of Actinomyces viscous. The direct contact test revealed that colony forming unit (CFU) count of Actinomyces viscous was comparable among the experimental and control materials. The flowable RBCs containing 1% CS had significantly higher VH compared to control and other experimental flowable RBC groups. The microhybrid RBCs consisting of 0.50% CS exhibited significantly higher VH compared to experimental microhybrid RBC group containing 1% CS.

Effect of laser treatment on outcomes of tooth replantation - A systematic review.

OBJECTIVES: Over the last few years, several studies have investigated the effect of laser treatment on the replantation of avulsed teeth. We conducted this study to systematically analyse and assess the outcomes and quality of these studies. METHODS: Using the keywords 'laser', 'tooth', and 'replantation', two investigators conducted an electronic search of the PubMed, MEDLINE, Embase, ISI Web of Knowledge and Google Scholar databases. Any studies not meeting the inclusion criteria were excluded. The focused question was 'Does laser treatment influence the outcomes of tooth replantation?' RESULTS: Nine studies were included and assessed in this review. In the majority of the selected studies, laser treatment had a positive outcome on preventing root resorption and in promoting periodontal regeneration. However, only three studies were given a quality score of 'medium', while six were marked as 'low'. CONCLUSION: Laser irradiation may reduce root resorption and favour periodontal regeneration following replantation of the avulsed tooth. However, more well-designed long-term animal and human studies are needed before lasers can be used clinically to improve the outcomes for replanted teeth.

Dentin Bond Integrity of Hydroxyapatite Containing Resin Adhesive Enhanced with Graphene Oxide Nano-Particles-An SEM, EDX, Micro-Raman, and Microtensile Bond Strength Study.

The aim was to synthesize and characterize an adhesive incorporating HA and GO nanoparticles. Techniques including scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX), micro-tensile bond strength (µTBS), and micro-Raman spectroscopy were employed to investigate bond durability, presence of nanoparticles inside adhesive, and dentin interaction. Control experimental adhesive (CEA) was synthesized with 5 wt% HA. GO particles were fabricated and added to CEA at 0.5 wt% (HA-GO-0.5%) and 2 wt% GO (HA-GO-2%). Teeth were prepared to produce bonded specimens using the three adhesive bonding agents for assessment of µTBS, with and without thermocycling (TC). The adhesives were applied twice on the dentin with a micro-brush followed by air thinning and photo-polymerization. The HA and GO nanoparticles demonstrated uniform dispersion inside adhesive. Resin tags with varying depths were observed on SEM micrographs. The EDX mapping revealed the presence of carbon (C), calcium (Ca), and phosphorus (P) in the two GO adhesives. For both TC and NTC samples, HA-GO-2% had higher µTBS and durability, followed by HA-GO-0.5%. The representative micro-Raman spectra demonstrated D and G bands for nano-GO particles containing adhesives. HA-GO-2% group demonstrated uniform diffusion in adhesive, higher µTBS, adequate durability, and comparable resin tag development to controls.

Clinical effectiveness of anorganic bovine-derived hydroxyapatite matrix/cell-binding peptide grafts for regeneration of periodontal defects: a systematic review and meta-analysis.

Aim: To ascertain clinical effectiveness of anorganic bovine-derived hydroxyapatite matrix/cell-binding peptide (ABM/P-15) for regeneration of periodontal defects. Materials & methods: Electronic databases (National Library of Medicine [Medline by PubMed], Cochrane Library [Wiley], CINAHL [EBSCO] and Medline [EBSCO]) were systematically searched up to December 2019. Randomized controlled clinical trials comparing ABM/P-15 grafts to conventional surgery for intrabony and gingival recession defects were included and evaluated intrabony defects including clinical attachment level (CAL), probing depth and gingival recession. Results: A significant gain in CAL (1.37 mm), and reduction in probing depth (1.22 mm) were shown by ABM/P-15 grafts than open flap debridement (p < 0.00001). The subgroup analysis also showed better results for ABM/P-15 grafts in CAL gain for intrabony defects. For furcation and gingival recession defects, no significant difference was seen. Conclusion: The adjunct use of ABM/P-15 grafts in conventional periodontal surgery is useful for periodontal regeneration of intrabony defects.

KMT2C, a histone methyltransferase, is mutated in a family segregating non-syndromic primary failure of tooth eruption.

Primary failure of tooth eruption (PFE) is a rare odontogenic defect and is characterized by failure of eruption of one or more permanent teeth. The aim of the study is to identify the genetic defect in a family with seven affected individuals segregating autosomal dominant non-syndromic PFE. Whole genome single-nucleotide polymorphism (SNP) genotyping was performed. SNP genotypes were analysed by DominantMapper and multiple shared haplotypes were detected on different chromosomes. Four individuals, including three affected, were exome sequenced. Variants were annotated and data were analysed while considering candidate chromosomal regions. Initial analysis of variants obtained by whole exome sequencing identified damaging variants in C15orf40, EPB41L4A, TMEM232, KMT2C, and FBXW10 genes. Sanger sequencing of all family members confirmed segregation of splice acceptor site variant (c.1013-2 A > G) in the KMT2C gene with the phenotype. KMT2C is considered as a potential candidate gene based on segregation analysis, the absence of variant in the variation databases, the presence of variant in the shared identical by descent (IBD) region and in silico pathogenicity prediction. KMT2C is a histone methyltransferase and recently the role of another member of this family (KMT2D) has been implicated in tooth development. Moreover, protein structures of KMT2C and KMT2D are highly similar. In conclusion, we have identified that the KMT2C gene mutation causes familial non-syndromic PFE. These findings suggest the involvement of KMT2C in the physiological eruption of permanent teeth.

Periodontal regeneration: a bibliometric analysis of the most influential studies.

Aim: The aim of the present study is to identify the most influential research articles and their main characteristics in the specialty of periodontal regeneration. Materials & methods: The Web of Science database advance search was performed in the subject category of 'Dentistry, Oral surgery and medicine' from January 2004 to October 2018 to retrieve citations data. Results: The majority of the articles were published in journals dedicated to the specialty of periodontology. Among the top-cited articles most emphasized study types were randomized control trials (n = 25) and reviews (n = 20). Conclusion: The present bibliometric analysis provides comprehensive information regarding the contributions made in the advancement of regenerative periodontal research. The authors from developed countries and affiliated with interdisciplinary/multicenter institutions have predominantly contributed.