Kinetics of Oriented Attachment of Mica Crystals.

Oriented attachment (OA), that is, the coalescence of crystals through attachment on coaligned crystal faces, is a nonclassical crystal growth process. Before attachment, a mesocrystal consisting of coaligned parallel crystals but with liquid separating them was observed. Fundamental questions such as why OA is kinetically favored and whether a mesocrystal stage is a prerequisite for OA are raised. Through combining brute-force molecular dynamics simulations and path samplings based on extensive umbrella simulations, we address these questions with a case study on the OA of a mica nanocrystal onto a mica crystal substrate in water. Brute-force simulations show that if two mica crystals are attached but largely misaligned, coalignment hardly appears. Thus, if OA is possible, then coalignment must appear before the attachment between crystals. Electrophoresis of the nanocrystal toward the substrate surface is spontaneous, but mesocrystal formation is occasional, also shown by brute-force simulations. Free energies along different pathways show that OA is spontaneous and kinetically favored over non-OA, and a mesocrystal formation is just a bifurcation in the pathway. OA is through a pathway in which the nanocrystal is tilted with respect to the substrate. Part of the nanocrystal is attached to the substrate first, and then, OA is gradually completed. Once a mesocrystal is occasionally formed, then a jump event is needed for the nanocrystal to get back to the OA pathway. The sampling technique here can hopefully guide the design of nanostructured materials facilitated by OA.

Interlayer Anions of Layered Double Hydroxides as Mobile Active Sites To Improve the Adsorptive Performance toward Cd2.

Layered double hydroxides (LDHs) have been considered important sinks for ionic contaminants in nature and effectively engineered adsorbents for environmental remediation. The availability of interlayer active sites of LDHs is critical for their adsorptive ability. However, inorganic LDHs generally have a nano-confined interlayer space of ca. 0.3-0.5 nm, and it is unclear how LDHs can utilize their interlayer active sites during the adsorption process. Thus, LDHs intercalated with SO42-, PO43-, NO3-, Cl-, or CO32- were taken as examples to reveal this unsolved problem during Cd2+ adsorption. New adsorption behaviors and pronounced differences in adsorption performance were observed. Specifically, SO42-/PO43- intercalated LDHs showed a maximum Cd2+ adsorption capacity of 19.2/9.8 times higher than other LDHs. The ligand exchange of H+ (on the surface -OH) by Cd2+ and formation of Cd-SO42-/PO43- complexes led to the efficient removal of Cd2+. Interestingly, interlayer SO42- was demonstrated to be able to move to the edges/outer surfaces of LDHs, providing abundant movable adsorption sites for Cd2+. This novel phenomenon made the SO42- intercalated LDH a superior adsorbent for Cd2+ among the tested LDHs, which also suggests that LDHs with a nano-confined interlayer space can also highly utilize their interlayer active sites based on the mobility of interlayer anions, offering a new method for constructing superior LDH adsorbents.

Location of Artinite (Mg2CO3(OH)2·3H2O) within the MgO-CO2-H2O system using ab initio thermodynamics.

The MgO-CO2-H2O system have a variety of important industrial applications including in catalysis, immobilisation of radionuclides and heavy metals, construction, and mineralisation and permanent storage of anthropogenic CO2. Here, we develop a computational approach to generate phase stability plots for the MgO-CO2-H2O system that do not rely on traditional experimental corrections for the solid phases. We compare the predictions made by several dispersion-corrected density-functional theory schemes, and we include the temperature-dependent Gibbs free energy through the quasi-harmonic approximation. We locate the Artinite phase (Mg2CO3(OH)2·3H2O) within the MgO-CO2-H2O phase stability plot, and we demonstrate that this widely-overlooked hydrated and carbonated phase is metastable and can be stabilised by inhibiting the formation of fully-carbonated stable phases. Similar considerations may apply more broadly to other lesser known phases. These findings provide new insight to explain conflicting results from experimental studies, and demonstrate how this phase can potentially be stabilised by optimising the synthesis conditions.

Oxygen Vacancy-Mediated CuCoFe/Tartrate-LDH Catalyst Directly Activates Oxygen to Produce Superoxide Radicals: Transformation of Active Species and Implication for Nitrobenzene Degradation.

Oxygen vacancies play a vital role in the catalytic activity of layered double hydroxide (LDH) catalysts in wastewater treatment. However, the mechanism of oxygen vacancy-mediated LDH-activated oxygen to produce reactive oxygen species (ROS) still lacks a reasonable explanation. In this work, a tartrate-modified CuCoFe-LDH (CuCoFe/Tar-LDH) with abundant oxygen vacancies was designed, which can efficiently degrade nitrobenzene (NB) under room conditions. The technical energy consumption is 0.011 kW h L-1. According to the characterization and calculation results, it is proposed that oxygen vacancies are formed because of the oxygen deficiency which is caused by the reduction of the energy between the metal ion and oxygen, and the metal ion transitions to a lower state. Compared with CuCoFe-LDH, the oxygen vacancy formation energy of CuCoFe/Tar-LDH decreased from 1.98 to 1.13 eV. The O2 bond length adsorbed on the oxygen vacancy is 1.27 Å, close to the theoretical length of superoxide radicals (•O2-) (1.26 Å). Radical trapping experiments and electron spin-resonance spectroscopy spectrum prove that •O2- is an important precursor of •OH. This work is dedicated to the in-depth exploration of the oxygen vacancy-mediated CuCoFe/Tar-LDH catalyst activation mechanism for molecular oxygen and the conversion relationship between ROS.

A Combined Remediation Strategy of Arsenic and Cadmium in the Paddy Soil of Polymetallic Mining Areas.

The combined pollution of arsenic (As) and cadmium (Cd) are quite common in the polymetallic mining areas located in southern China. In the present study, field experiments were established for the purpose of exploring a simultaneous remediation strategy of rice variety-water management-contaminant immobilization on the As and Cd contamination in paddy soil. The obtained results revealed that the Maba Yinzhan was the best low-accumulation rice variety, with As and Cd concentrations of 0.54 and 0.16 mg kg-1, respectively, in the rice grains. On the basis of water management during heading stage, the treatment using 0.15 wt% lime plus 0.5 wt% ferro-ferric oxide (FO) decreased the As and Cd concentrations by 64.02% and 34.78%, respectively, in the grains. The results of this study potentially provide an effective remediation solution for the As/Cd contaminated soils in polymetallic mining areas.

Closest-Packing Water Monolayer Stably Intercalated in Phyllosilicate Minerals under High Pressure.

The directional hydrogen-bond (HB) network and nondirectional van der Waals (vdW) interactions make up the specificity of water. Directional HBs could construct an ice-like monolayer in hydrophobic confinement even in the ambient regime. Here, we report a water monolayer dominated by vdW interactions confined in a phyllosilicate interlayer under high pressure. Surprisingly, it was in a thermodynamically stable state coupled with bulk water at the same pressure (P) and temperature (T), as revealed by the thermodynamic integration approach on the basis of molecular dynamics (MD) simulations. Both classical and ab initio MD simulations showed water O atoms were stably trapped and exhibited an ordered hexagonal closest-packing arrangement, but OH bonds of water reoriented frequently and exhibited a specific two-stage reorientation relaxation. Strikingly, hydration in the interlayer under high pressure had no relevance with surface hydrophilicity rationalized by the HB forming ability, which, however, determines wetting in the ambient regime. Intercalated water molecules were trapped by vdW interactions, which shaped the closest-packing arrangement and made hydration energetically available. The high pressure-volume term largely drives hydration, as it compensates the entropy penalty which is restricted by a relatively lower temperature. This vdW water monolayer should be ubiquitous in the high pressure but low-temperature regime.

Intrinsic water layering next to soft, solid, hydrophobic, and hydrophilic substrates.

How a substrate modulates properties of water upon it and how far the perturbation is present remain to be fundamental questions in surface science. To answer these questions, we develop a layer-by-layer exfoliation method to identify physically meaningful water layers upon a substrate through molecular dynamics simulations under ambient conditions. The results show a qualitatively consistent long-ranged layer-by-layer propagation of the atomic structure, irrespective of whether the substrate is soft, solid, hydrophobic, or hydrophilic. The capillary-wave fluctuation of a water layer upon air or oil diverges with long wavelength but is truncated upon solid substrates by an effective field, which exhibits a long-ranged decay but its strength is almost irrelevant with substrate chemistry. The distinction in the water structure and atomic dynamics due to substrate specificity is mostly limited to the outmost layer. We conclude a long-ranged layering organization and a short-ranged substrate-dependent specificity for interfacial water.

Use of nano-/micro-magnetite for abatement of cadmium and lead contamination.

Structural variations of a mineral dictate its adsorption capacity which affects the mobility and toxicity of contaminants in natural and engineered systems. Present batch study evaluates the adsorption of lead (Pb) and cadmium (Cd) onto three magnetites having nanometric (M1-30 nm and M2-60 nm) and micrometric particle sizes (M3-1.5 µm). Obtained data revealed that particle size of tested magnetites strongly affected the extent and kinetics of metal adsorption and desorption. Observed order of adsorption efficiency was M1 > M2 > M3 with optimum monolayer adsorption of 408.14, 331.40, 178.47 mg/g (for Pb) and 228.05, 170.86, 83.49 mg/g (for Cd), respectively. Adsorption data were well fitted to the Freundlich (R2 = 0.99), Langmuir (R2 = 0.99) and pseudo-first order models (R2 = 0.98). Electrostatic attraction and surface precipitation interaction via external mass transfer between bulk liquid-solid interfaces were the potential adsorption pathways. Pb showed higher affinity than Cd in multi-metal system. Desorption efficiency was higher in acidic environment (92%) than in distilled water (44%). Moreover, regenerated magnetite samples retained good adsorption capacity for six cycles. As soils are characterized by large variability of iron minerals, these findings have important implications regarding the transport and immobilization of contaminants particularly in the management of contaminated soils.

Arrangement Models of Keggin-Al30 and Keggin-Al13 in the Interlayer of Montmorillonite and the Impacts of Pillaring on Surface Acidity: A Comparative Study on Catalytic Oxidation of Toluene.

Acid-base reactivity is a key factor for understanding the interfacial geochemistry of clay minerals. Numerous studies showed the significant role of surface acidity of clay minerals in the geological processes and environmentally related applications. In this work, montmorillonite (Mt) was pillared by polycations of Keggin-Al13 and Keggin-Al30. Arrangement models of Keggin-Al13 and Keggin-Al30 in the interlayer region of Mt were put forward based on the chemical composition analysis, the structural formula calculation of Mt, and the results of powder X-ray diffraction. Ammonia temperature-programmed desorption and diffuse reflectance Fourier transform infrared methods were applied to explore the impacts of pillaring by polycations (Keggin-Al13 and Keggin-Al30) on the surface acidic characteristics of Mt. Results demonstrated that one Keggin-Al30 polycation can affect an area of 9.5 unit cells (from two layers, with 4.7-4.8 unit cells in each layer) in Mt, whereas a Keggin-Al13 polycation controls an area of 7.1 unit cells (from two layers, with 3.5-3.6 unit cells in each layer). Pillaring by polycations could lead to a lot of surface acid sites (1.33 mmol NH3/g) on Mt with the main type of Bronsted acid sites. The increase of surface acid sites on both Keggin-Al13-pillared Mt (Al13-PILM) and Keggin-Al30-pillared Mt (Al30-PILM) is attributed to the high positive charge and high content of aluminum per unit of polycation, which affects the formation of Bronsted acid sites and structural changes of Mt layers. Catalytic oxidation of toluene provided evidence for the high catalytic activity of Al30-PILM under much lower temperature at 78 °C compared with that of Al13-PILM and Mt at 207 and 285 °C, respectively. The basic finding in this study not only reveals the possible sources of abundant micropores and mesopores in the micro/mesoporous materials of Al13-PILM and Al30-PILM but also provides a reasonable mechanism for the formation of abundant Bronsted surface acid sites on these two types of pillared materials. The novel Al30-PILM with an excellent micro/mesoporous structure and extremely high thermal stability also exhibits a potential ability in the application of heterogeneous acid catalysis.

Fabrication of Ag2O/Ag decorated ZnAl-layered double hydroxide with enhanced visible light photocatalytic activity for tetracycline degradation.

The photocatalytic performance of layered double hydroxides (LDH) is usually confined to the slow interface mobility and high recombination rate of photogenerated electron-hole pairs in material. To overcome the low photocatalytic efficiency, novel Ag2O/Ag decorated LDH (LDH-Ag2O/Ag) was successfully synthesized by depositing Ag2O on the surface of LDH and then converted to Ag° nanoparticles in the right position after heat treatment. The as-synthesized LDH-Ag2O/Ag composites were characterized by Powder X-ray diffraction (XRD), Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV-visible diffuse reflectance spectra (UV-vis DRS), photoluminescence spectra (PL) and transient photocurrent (TPC) analysis. Compared with virgin LDH, the photocatalytic activities of LDH-Ag2O/Ag composites were enhanced significantly. The optimum photocatalytic efficiency of LDH-Ag10 (0.0184 min-1) was nearly 46 times higher than that of virgin LDH (0.0004 min-1). The result of active species trapping experiments indicated that •OH, h+, and •O2- have an effect on the TC degradation, where •OH played the predominant role during the photocatalytic process. The possible photocatalytic mechanisms involving the charge transfer pathway and reactive species generation during the process of TC degradation were also discussed. The improved photocatalytic activity of LDH-Ag2O/Ag could be attributed to the synergetic effect between LDH and Ag2O/Ag that extended visible light range and reduced photogenerated charge carriers recombination.

TiO2/Schwertmannite nanocomposites as superior co-catalysts in heterogeneous photo-Fenton process.

The heterogeneous photo-Fenton reaction is an effective technique in combating organic contaminants for both soil and water remediation, and extensive studies have focused on enhancing its efficiency and reducing its costs. In this work, we developed novel photo-Fenton catalysts by simply milling commercially available TiO2 (P25) with Schwertmannite (Sh), a natural iron-oxyhydroxysulfate nanomineral. We expect that the photo-generated electrons from TiO2 could continuously migrate to Sh, which then could enhance the separation of electron-hole pairs on TiO2 and accelerate the reduction of Fe(III) to Fe(II) on Sh, leading to high degradation efficiency of the target organic contaminants. SEM and TEM results showed the distribution of TiO2 on Sh surface for the nanocomposites (TiO2/Sh). Under simulated sunlight irradiation, the much higher content of Fe(II) was determined on TiO2/Sh than on Sh via a common method in the iron ore, and the consumption of H2O2 and the production of •OH were more significant in the TiO2/Sh system than those in the TiO2 and Sh systems. These results well support our hypothesis that the photo-generated electrons could migrate from TiO2 to Sh on the composites, and can also explain the much higher degradation efficiency of Rhodamine B (RhB) in the TiO2/Sh system. Besides, TiO2/Sh had lower Fe dissolution as compared with Sh, and retained high catalytic stability after four repeated cycles. Above merits of the TiO2/Sh composites, in combining with their simple synthesis method and low-cost property, indicated that they should have promising applications as heterogeneous photo-Fenton catalysts.

Influences of Cation Ratio, Anion Type, and Water Content on Polytypism of Layered Double Hydroxides.

Layered double hydroxides (LDHs) are a significant sink of anions (CO32-, SO42-, NO3-, Cl-, etc.) and divalent transition-metal cations in soil. The anion exchange capacity gives rise to functional materials. The stability of LDHs is determined by the interaction between cation-bearing layers and intercalated water and anions, which is correlated with polytypism and coordination structure. A systematic investigation is performed to show the influence of cation ratio, anion type, and water content on polytypism, swelling behavior, and interlayer structure of Mg-Al-LDHs using molecular dynamics simulations. LDHs intercalated with NO3- ions exhibit a polytype transition from 3 R1 (three-layer rhombohedral polytype) to 1 T (one-layer trigonal polytype) with increasing water content. NO3- ions exhibit a D3 h point group symmetry at low water contents. The polytype transition coincides with the complete transformation into tilted NO3- ion with a C2 v point group symmetry. The transition appears at a lower water content when the Mg/Al ratio is lower. LDHs with SO42- ions exhibit a three-stage polytypism. The first and last stages are 3 R1. The intermediate stage could be 1 T or a mixture of different O(octahedra)-type interlayers, which depends on the cation ratio. The relative popularity of SO42- ions with a C s point group symmetry is characteristic for the intermediate stage, while mostly SO42- ions exhibit a C3 v symmetry. There is no clear relevance between cation ratio and water content at which a polytype transition happens. The configurational adjustments of NO3- and SO42- ions facilitate the swelling behavior of LDHs. LDHs with CO32- or Cl- ions always maintain a 3 R1 polytype irrespective of water content and hardly swell. The configurations of anions and water reflect local coordination structure due to hydrogen bonds. The layer-stacking way influences long-ranged Coulombic interactions. Hydrogen-bonding structure and long-ranged Coulombic interactions collectively determine polytypism and stability of LDHs.

Interaction of polyhydroxy fullerenes with ferrihydrite: adsorption and aggregation.

The rapid development of nanoscience and nanotechnology, with thousands types of nanomaterials being produced, will lead to various environmental impacts. Thus, understanding the behaviors and fate of these nanomaterials is essential. This study focused on the interaction between polyhydroxy fullerenes (PHF) and ferrihydrite (Fh), a widespread iron (oxyhydr)oxide nanomineral and geosorbent. Our results showed that PHF were effectively adsorbed by Fh. The adsorption isotherm fitted the D-R model well, with an adsorption capacity of 67.1mg/g. The adsorption mean free energy of 10.72kJ/mol suggested that PHF were chemisorbed on Fh. An increase in the solution pH and a decrease of the Fh surface zeta potential were observed after the adsorption of PHF on Fh; moreover, increasing initial solution pH led to a reduction of adsorption. The Fourier transform infrared spectra detected a red shift of C-O stretching from 1075 to 1062cm-1 and a decrease of Fe-O bending, implying the interaction between PHF oxygenic functional groups and Fh surface hydroxyls. On the other hand, PHF affected the aggregation and reactivity of Fh by changing its surface physicochemical properties. Aggregation of PHF and Fh with individual particle sizes increasing from 2nm to larger than 5nm was measured by atomic force microscopy. The uniform distribution of C and Fe suggested that the aggregates of Fh were possibly bridged by PHF. Our results indicated that the interaction between PHF and Fh could evidently influence the migration of PHF, as well as the aggregation and reactivity of Fh.

Influence of cobalt species on the catalytic performance of Co-N-C/SiO2 for ethylbenzene oxidation.

In this paper, cobaltporphyrin is used as a precursor to synthesize carbon nitrides with metal active sites supported on silica spheres by heat treatment (i.e. M-N-C/SiO2). The catalytic performance of M-N-C/SiO2 for ethylbenzene oxidation has been investigated and techniques such as N2 adsorption/desorption isotherm, NH3-TPD, HRTEM, STEM mapping and X-ray photoelectron spectroscopy (XPS) are employed to explore the active sites for ethylbenzene oxidation. XPS results show that cobalt compounds, such as CoOx and metallic Co, as well as cobalt nitrides, such as Co-Nx, are formed after the pyrolysis of cobaltporphyrin. However, according to the NH3-TPD experiment, Co-Nx may be the primary active site. When Co-Nx is poisoned by KSCN, the significant loss of catalytic activity further proves and verifies that Co-Nx instead of CoOx is the primary active site of M-N-C/SiO2 for ethylbenzene oxidation.

The UV/Fenton degradation of tetrabromobisphenol A catalyzed by nanocrystalline chromium substituted magnetite.

The heterogeneous UV/Fenton degradation of tetrabromobisphenol A (TBBPA) catalyzed by nanocrystalline Fe3O4 and Fe2.04Cr0.96O4 was investigated, with focus on the influence of UV light and initial pH, degradation pathways and effect of Cr substation. The catalysts were prepared by a precipitation-oxidation method and characterized by chemical analysis, XRD, XAFS, TG-DSC, BET surface area and magnetometer. At pH 6.7 and under UV irradiation, almost complete degradation of TBBPA by Fe2.04Cr0.96O4 was accomplished within 240 min, and the leaching Fe ions were negligible. The substitution of chromium greatly increased the BET specific surface area and surface hydroxyl amount, which improved the heterogeneous UV/Fenton catalytic activity of magnetite. Moreover, Cr3+ on the octahedral sites enhanced the electron transfer process in the magnetite structure to accelerate the *OH generation. The produced *OH radicals preferentially attacked the C-Br bonds of TBBPA and then ß-cleavaged the C-C bonds between benzene rings and isopropyl groups. The above results are of great significance for well understanding the effect of transition metal substitution on the UV/Fenton catalytic activity of magnetite and prospecting the application of magnetite minerals in environmental purification.

Phosphorus adsorption from aqueous solutions using different types of cement: kinetics, isotherms, and mechanisms.

Exploring low-cost and high-performance phosphorus (P) adsorbents is key to controlling P contamination in water. This study evaluated the P adsorption performance of three types of cement: Ordinary Portland cement (OPC), Portland slag cement (PSC), and Portland pozzolana cement (PPC). Furthermore, SEM-EDS, XRD, XPS, and FTIR were employed to reveal the adsorption mechanism. The results showed that the pseudo-second-order model exhibited higher regression coefficients than the pseudo-first-order model, indicating that chemisorption dominated the adsorption process. The Langmuir equation fitted the P adsorption data well, with maximum P adsorption capacities of 245.8, 226.1, and 210.0 mg g-1 for OPC, PSC, and PPC at 25 °C, respectively. P adsorption capacities decreased gradually with increasing initial pH and reached their maximum values at pH 3. The anions of F-, CO32-, and SO42- negatively affected P adsorption due to the competitive adsorption with Ca2+. The results of XPS, XRD, and FTIR confirmed that Ca-P precipitates (i.e., hydroxyapatite) were the main removal mechanism. A real domestic sewage experiment showed that 0.6 g L-1 OPC effectively reduced the P concentration from 2.4 to below 0.2 mg L-1, with a dosage cost of 0.034 $ per ton. This study indicated that cement, as a low-cost and efficient P adsorbent, has great potential for application in removing P from acidic and neutral wastewater.

Highly efficient recovery of Zn2+/Cu2+ from water by using hydrotalcite as crystal seeds.

The efficient and waste-free recovery of heavy metals is critical for heavy metal wastewater treatment. In this work, we explored how heavy metals can be recovered as valuable chemicals in the presence of crystal seeds. Hydrotalcite (one kind of layered double hydroxides (LDHs)) was used as crystal seeds to recover Zn2+ in the presence of Al3+ from water (i.e., seed-Zn2+-Al3+ system), which was compared with the monometallic heterogeneous system (seed-Zn2+) and direct coprecipitation (Zn2+-Al3+) system. Our results demonstrated that the seed-Zn2+-Al3+ system possessed a recovery rate of 2.6-2.8 times and a recovery kinetic rate of 2.7-5.9 times higher than those of the other two systems. Differing from the latter two systems, hydrotalcite seeds could induce Zn2+ and Al3+ to form ZnAl-LDH in seed-Zn2+-Al3+. Interestingly, the ZnAl-LDH presents a compositional divalent/trivalent cation molar ratio of ca. 3, which is comparable with the value in the hydrotalcite. It was demonstrated that the hydrotalcite seeds could act as a template to significantly induce the formation of ZnAl-LDH complying with the seed's structure and compositional ratio. Similar induction effect of seeds as the Zn2+ system was further verified in Cu2+ systems. This work provides a novel strategy for efficient recovery of heavy metals with product selectivity.

Enhanced ammonia removal in tidal flow constructed wetland by incorporating steel slag: Performance, microbial community, and heavy metal release.

Utilizing alkaline solid wastes, such as steel slag, as substrates in tidal flow constructed wetlands (TFCWs) can effectively neutralize the acidity generated by nitrification. However, the impacts of steel slag on microbial communities and the potential risk of heavy metal release remain poorly understood. To address these knowledge gaps, this study compared the performance and microbial community structure of TFCWs filled with a mixture of steel slag and zeolite (TFCW-S) to those filled with zeolite alone (TFCW-Z). TFCW-S exhibited a much higher NH4+-N removal efficiency (98.35 %) than TFCW-Z (55.26 %). Additionally, TFCW-S also achieved better TN and TP removal. The steel slag addition helped maintain the TFCW-S effluent pH at around 7.5, while the TFCW-Z effluent pH varied from 3.74 to 6.25. The nitrification and denitrification intensities in TFCW-S substrates were significantly higher than those in TFCW-Z, consistent with the observed removal performance. Moreover, steel slag did not cause excessive heavy metal release, as the effluent concentrations were below the standard limits. Microbial community analysis revealed that ammonia-oxidizing bacteria, ammonia-oxidizing archaea, and complete ammonia-oxidizing bacteria coexisted in both TFCWs, albeit with different compositions. Furthermore, the enrichment of heterotrophic nitrification-aerobic denitrification bacteria in TFCW-S likely contributed to the high NH4+-N removal. In summary, these findings demonstrate that the combined use of steel slag and zeolite in TFCWs creates favorable pH conditions for ammonia-oxidizing microorganisms, leading to efficient ammonia removal in an environmentally friendly manner.

Electron transfer mediated photo-Fenton-like synergistic catalysis of Fe,Cu-doped MIL-101 coupled with Ag3PO4: Quantitative evaluation and DFT calculations.

Widespread use of tetracycline (TC) results in its persistent residue and bioaccumulation in aquatic environments, posing a high toxicity to non-target organisms. In this study, a bimetal-doped composite material Ag3PO4/MIL-101(Fe,Cu) has been designed for the treatment of TC in aqueous solutions. As the molar ratio of Fe/Cu in composite is 1:1, the obtained material AP/MFe1Cu1 is placed in an aqueous environment under visible light irradiation in the presence of 3 mM peroxydisulfate (PDS), which forms a photo-Fenton-like catalytic system that can completely degrade TC (10 mg/L) within 60 min. Further, the degradation rate constant (0.0668 min-1) is 5.66 and 7.34 times higher than that of AP/MFe and AP/MCu, respectively, demonstrating a significant advantage over single metal-doped catalysts. DFT calculations confirm the strong adsorption capacity and activation advantage of PDS on the composite surface. Therefore, the continuous photogenerated electrons (e-) accelerate the activation of PDS and the production of SO4•-, resulting in the stripping of abundant photogenerated h + for TC oxidation. Meanwhile, the internal circulation of FeⅢ/FeⅡ and CuⅡ/CuⅢ in composite also greatly enhances the photo-Fenton-like catalytic stability. According to the competitive dynamic experiments, SO4•- have the greatest contribution to TC degradation (58.93%), followed by 1O2 (23.80%). The degradation intermediates (products) identified by high-performance liquid chromatography-mass spectrometry (HPLC/MS) technique indicate the involvement of various processes in TC degradation, such as dehydroxylation, deamination, N-demethylation, and ring opening. Furthermore, as the reaction proceeds, the toxicity of the intermediates produced during TC degradation gradually decreases, which can ensure the safety of the aquatic ecosystem. Overall, this work reveals the synergy mechanism of PDS catalysis and photocatalysis, as well as provides technical support for removal of TC-contaminated wastewater.

Novel heterogeneous Fenton catalysts for promoting carbon iron electron transfer by one-step hydrothermal synthesization.

Carbon materials play a crucial role in promoting the Fe(III)/Fe(II) redox cycle in heterogeneous Fenton reactions. However, the electron transfer efficiency between carbon and iron is typically low. In this study, we prepared a novel heterogeneous Fenton catalyst, humboldtine/hydrothermal carbon (Hum/HTC), using a one-step hydrothermal method and achieved about 100 % reduction in Fe(III) during synthesis. Moreover, the HTC continuously provided electrons to promote Fe(II) regeneration during the Fenton reaction. Electron paramagnetic resonance (EPR) and quenching experiments showed that Hum/HTC completely oxidized As(III) to As(V) via free radical and non-free radical pathways. Attenuated total reflectance Fourier-transform infrared (ATR-FTIR) and two-dimensional correlation spectroscopy (2D-COS) analyses revealed that monodentate mononuclear (MM) and bidentate binuclear (BB) structures were the dominant bonding methods for As(V) immobilization. 40 %Hum/HTC exhibited a maximum As(III) adsorption capacity of 167 mg/g, which was higher than that of most reported adsorbents. This study provides a novel strategy for the efficient reduction of Fe(III) during catalyst synthesis and demonstrates that HTC can continuously accelerate Fe(II) regeneration in heterogeneous Fenton reactions.