Blue Laser for Polymerization of Bulk Fill Composites: Influence on dentin bond strength and temperature rise during curing and co-curing method.

Blue diode lasers are alternative curing devices for dental composites. The aim of this study was to investigate the influence of blue diode laser polymerization on shear bond strength of bulk fill composites to human dentin and temperature rise during two types of polymerization. Composite cylinders of SDR Plus(SDR) and Ever X Flow(EX) were bonded to dentin slabs using Adhese Universal and curing devices blue diode laser (449 nm, 1.6 W) and Power Cure LED. For each material and curing device there were two polymerization approaches: 1)conventional: separate curing of adhesive; 2)co-curing: simultaneous adhesive and composite curing. Polymerization modes for each material in conventional and co-curing(c) approach were: blue laser 2000 mW/cm2 for 5 s (L5 and L5c); blue laser 1000 mW/cm2 for 10 s (L10 and L10c); Power Cure 2000 mW/cm2 for 5 s (LED5 and LED5c); Power Cure 1000 mW/cm2 for 10 s (LED10 and LED10c). Temeperature was measured using thermal vision camera. For SDR, the highest bond strength was 24.3 MPa in L10c, and the lowest 9.2 MPa in LED5c. EX exhibited the highest bond strength(21.3 MPa) in LED5, and the lowest in L5(7.7 MPa). The highest temperature rise for SDR was in L10 and L5 (7.3 and 7.2 °C), and the lowest in LED5(0.8 °C). For EX, the highest temperature rise was in L5 (13.0 °C), and the lowest in LED5 (0.7 °C). Temperature rise was higher during blue laser polymerization, especially at high intensity and with conventional curing. Preferable blue laser curing mode is co-curing at 1000mW/cm2 for 10 s.

High-power 450 nm blue diode laser for endoscopic mucosal resection/endoscopic submucosal dissection in the stomach: Preliminary results on a porcine model with a modified flexible endoscope.

BACKGROUND: Due to the precise vaporization of the novel 450 nm blue diode laser in soft tissues (i.e., bladder and colon) in our previous studies, porcine stomach tissues were applied here to certify its efficacy in endoscopic mucosal resection (ESR)/endoscopic submucosal dissection (ESD) for hypothetical lesions ex vivo and in vivo. MATERIALS AND METHODS: In an ex vivo study of ESR, 20 pieces of tissues (8 cm × 6 cm) from 7 fresh stomachs after spraying saline were vaporized with a three-dimensional scanning system using the blue diode laser at a maximum of 30 W, a different treatment speed and working distance (WD). In ex vivo ESD, 18 pieces of tissues from 6 fresh stomachs were used and the same laser parameters were used to perform the procedure. The depth, width, and coagulation of the laser vaporization were measured. Furthermore, the large scales (2.0 cm × 1.5 cm) for 18 hypothetical lesions of the gastric mucosa and submucosa of the 6 fresh stomachs were also resected with a modified flexible endoscope. In vivo, six hypothetical lesions of six porcine were vaporized by the novel blue laser, and the resultant lesions at the acute and chronic stages were assessed by the naked eye and hematoxylin and eosin staining. RESULTS: In the contact mode, more tissue was vaporized, and the thickness of the coagulation was stable when the WD was 0-2 mm, whose value varied from 0.33 to 1.73 mm. In the gastroscopy model, the mean thickness of coagulation from the mucosa was 0.67 mm, and a significant carbonization zone was not observed. In vivo, the laser beam could accurately act on the hypothetical target. No bleeding and clear vision were present in the procedure. After 3 weeks, tissue healing was well recovered after laser coagulation, resection, and submucosal dissection. CONCLUSIONS: In the present study, the novel 450 nm blue diode laser exhibited ideal vaporization and thinner coagulation thickness in the porcine stomach, which indicated that it could be alternately used as a new device for stomach lesions.

The impact of the laser fiber-tissue distance on histological parameters in a porcine kidney model.

PURPOSE: To evaluate the impact of the fiber-tissue distance on histological parameters in a porcine kidney model. METHODS: Four lasers were tested at 60 W using a 600-µm bare-ended fiber: a continuous wave (cw) thulium fiber laser (TFL), a super pulsed (SP) TFL, a Ho:YAG laser, and a blue diode laser (BDL). All tissue samples were mounted on a motorized XY-translation stage. The fiber-tissue distance was changed within a range from 0to 6 mm. Ten incisions were made with each laser at each distance. Afterwards, the tissue samples were sliced with a microtome for lactate dehydrogenase staining to determine zones of thermal damage. RESULTS: In contact mode, the largest incision depth was found for the cw TFL (1.7 ± 0.1 mm) compared to the SP TFL (1.0 ± 0.1 mm), BDL (0.9 ± 0.1 mm) and HoYAG laser (1.1 ± 0.1 mm), respectively. With regard to the coagulative properties, the SP TFL and the Ho:YAG laser showed comparable coagulation depths with 0.7 ± 0.1 and 0.6 ± 0.1 mm, respectively. At 2 mm fiber-tissue distance, the Ho:YAG laser was the only laser that vaporized tissue (incision depth: 0.2 ± 0.1 mm). The BDL was the only laser that caused coagulation at a distance of 3-5 mm. CONCLUSION: Our results support the clinical observation that cw TFL must be defocused for best coagulation, while the coagulation depth of the SP TFL remains nearly constant within the range of 0-3 mm. Increasing the distance of the laser fiber to the tissue up to 5 mm did not cause significant differences with regard to coagulation depth using the BDL.

Evaluation of photopolymerization efficacy and temperature rise of a composite resin using a blue diode laser (445 nm).

The purpose of this study was to evaluate the photopolymerization efficacy of a diode laser (445 nm) for use with a composite containing camphorquinone and to estimate the safety of the method related to the temperature rise. Five cylindrical composite specimens were prepared for each thickness: 1, 2, and 3 mm. Three light-curing modes were investigated: a light emitting diode (LED) unit and a diode laser (445 nm) with output powers at 0.7 W or 3 W. Evaluation of the polymerization efficacy was based on Vickers hardness measurements, and the highest temperatures at the bottom of the specimens were recorded using a K-type thermocouple. The highest microhardness was observed after the diode laser curing operating at 3 W. A comparison of the microhardness of the 0.7 W laser cured specimens with the LED cured specimens showed a statistically significant difference in favor of the laser curing. Laser curing operating at 3 W resulted in extremely high temperatures. Laser curing at 0.7 W resulted in statistically significantly higher maximum temperatures than did LED curing for both 1 mm thick (52.9°C against 45.4°C) and 3 mm thick (43.6°C against 40.9°C) specimens. Diode laser (445 nm) may be an alternative for photopolymerization of composite materials and may result in a higher degree of conversion and depth of cure of composites than what has been seen with LED curing units when they emit at the same energy density.

Ex vivo and animal study of the blue diode laser, Tm fiber laser, and their combination for laparoscopic partial nephrectomy.

BACKGROUND AND OBJECTIVES: To evaluate the feasibility of using a novel blue diode laser (blue laser), a thulium fiber laser (Tm laser), and their combination as a directed-energy surgical tool in laparoscopic partial nephrectomy (LPN). STUDY DESIGN/MATERIALS AND METHODS: The blue laser emitting at 442 nm, the Tm laser emitting at 1,940 nm wavelengths, and the combination of them were tested. First, cutting and coagulative abilities of the lasers were characterized ex vivo on porcine kidney in air and CO2 . Histological staining was performed to assess the efficiency of ablation and coagulation. Next, experimental LPN was performed on a porcine model at zero ischemia. Upper and lower segments of both kidneys were resected. Total operation time and resection time were measured; bleeding and carbonization were evaluated. RESULTS: Ex vivo data show that laser-induced ablation and coagulation processes do not differ substantially between CO2 and air environments. Histological analysis of ex vivo incisions demonstrates that the blue laser produced deep ablation with relatively narrow coagulation zone, whereas Tm laser was less efficient in terms of ablation but possessed excellent coagulative properties. Experimental LPN revealed that the blue laser provided fast cutting with minimal carbonization, whereas Tm laser induced slow cutting with strong carbonization. The combination of the blue and Tm lasers provided the most promising results demonstrating the highest resection rate, almost carbonization free resection surface and clinically acceptable hemostasis enabling LPN without the need for vessel clamping. CONCLUSIONS: The blue laser can be efficiently utilized in LPN. Furthermore, the combination of the blue and Tm lasers into a single modality may be beneficial for further development of successful laser-assisted LPN. Lasers Surg. Med. © 2019 Wiley Periodicals, Inc.

Effectiveness of photopolymerization in composite resins using a novel 445-nm diode laser in comparison to LED and halogen bulb technology.

Challenges especially in the minimal invasive restorative treatment of teeth require further developments of composite polymerization techniques. These include, among others, the securing of a complete polymerization with moderate thermal stress for the pulp. The aim of this study is to compare current light curing sources with a blue diode laser regarding curing depth and heat generation during the polymerization process. A diode laser (445 nm), a LED, and a halogen lamp were used for polymerizing composite resins. The curing depth was determined according to the norm ISO 4049. Laser output powers of 0.1, 0.5, 1, and 2 W were chosen. The laser beam diameter was adapted to the glass rod of the LED and the halogen lamp (8 mm). The irradiation time was fixed at 40 s. To ascertain ΔT values, the surface and ground area temperatures of the cavities were simultaneously determined during the curing via a thermography camera and a thermocouple. The curing depths for the LED (3.3 mm), halogen lamp (3.1 mm) and laser(0.5/1 W) (3/3.3 mm) showed no significant differences (p < 0.05). The values of ΔTsurface as well as ΔTground also showed no significant differences among LED, halogen lamp, and laser(1 W). The ΔTsurface values were 4.1LED, 4.3halogen lamp, and 4.5 °C for the laser while the ΔTground values were 2.7LED, 2.6halogen lamp, and 2.9 °C for the laser. The results indicate that the blue diode laser (445 nm) is a feasible alternative for photopolymerization of complex composite resin restorations in dentistry by the use of selected laser parameters.

Effect of radiant heat on conventional glass ionomer cements during setting by using a blue light diode laser system (445 nm).

The aim of this in vitro study was to evaluate the effect of radiant heat on surface hardness of three conventional glass ionomer cements (GICs) by using a blue diode laser system (445 nm) and a light-emitting diode (LED) unit. Additionally, the safety of the laser treatment was evaluated. Thirty disk-shaped specimens were prepared of each tested GIC (Equia Fil, Ketac Universal Aplicap and Riva Self Cure). The experimental groups (n = 10) of the study were as follows: group 1 was the control group of the study; in group 2, the specimens were irradiated for 60 s at the top surface using a LED light-curing unit; and in group 3, the specimens were irradiated for 60 s at the top surface using a blue light diode laser system (445 nm). Statistical analysis was performed using one-way ANOVA and Tukey post-hoc tests at a level of significance of a = 0.05. Radiant heat treatments, with both laser and LED devices, increased surface hardness (p < 0.05) but in different extent. Blue diode laser treatment was seemed to be more effective compared to LED treatment. There were no alterations in surface morphology or chemical composition after laser treatment. The tested radiant heat treatment with a blue diode laser may be advantageous for the longevity of GIC restorations. The safety of the use of blue diode laser for this application was confirmed.

Photodynamic inactivation of pathogenic species Pseudomonas aeruginosa and Candida albicans with lutetium (III) acetate phthalocyanines and specific light irradiation.

Photodynamic inactivation (PDI) is a light-associated therapeutic approach suitable for treatment of local acute infections. The method is based on specific light-activated compound which by specific irradiation and in the presence of molecular oxygen produced molecular singlet oxygen and other reactive oxygen species, all toxic for pathogenic microbial cells. The study presents photodynamic impact of two recently synthesized water-soluble cationic lutetium (III) acetate phthalocyanines (LuPc-5 and LuPc-6) towards two pathogenic strains, namely, the Gram-negative bacterium Pseudomonas aeruginosa and a fungus Candida albicans. The photodynamic effect was evaluated for the cells in suspensions and organized in 48-h developed biofilms. The relatively high levels of uptakes of LuPc-5 and LuPc-6 were determined for fungal cells compared to bacterial cells. The penetration depths and distribution of both LuPcs into microbial biofilms were investigated by means of confocal fluorescence microscopy. The photoinactivation efficiency was studied for a wide concentration range (0.85-30 µM) of LuPc-5 and LuPc-6 at a light dose of 50 J cm-2 from red light-emitting diode (LED; 665 nm). The PDI study on microbial biofilms showed incomplete photoinactivation (<3 logs) for the used gentle drug-light protocol.

Weldability and Mechanical Properties of Pure Copper Foils Welded by Blue Diode Laser.

The need to manufacture components out of copper is significantly increasing, particularly in the solar technology, semiconductor, and electric vehicle sectors. In the past few decades, infrared laser (IR) and green laser (GL) have been the primary technologies used to address this demand, especially for small or thin components. However, with the increased demand for energy saving, alternative joint techniques such as blue diode laser (BDL) are being actively explored. In this paper, bead-on-plate welding experiments on 0.2 mm thick pure copper samples employing a BDL are presented. Two sets of parameters were carefully selected in this investigation, namely Cu-1: Power (P) = 200 W; Speed (s) = 1 mm/s; and angle = 0°, and Cu-2: P = 200 W; s = 5 mm/s; and angle = 10°. The results from both sets of parameters produced defect-free full penetration welds. Hardness test results indicated relatively softer weld zones compared with the base metal. Tensile test samples fractured in the weld zones. Overall, the samples welded with Cu-1 parameters showed better mechanical properties, such as strength and elongation, than those welded with the Cu-2 parameters. The tensile strength and elongation obtained from Cu-1 were marginally lower than those of the unwelded pure copper. The outcomes from this research provide an alternative welding technique that is able to produce reliable, strong, and precise joints, particularly for small and thin components, which can be very challenging to produce.

The Effect of Different Output Powers of Blue Diode Laser along with Curcumin and Riboflavin against Streptococcus mutans around Orthodontic Brackets: An In Vitro Study.

OBJECTIVES: The aim of the present study was to determine the effects of antimicrobial photodynamic therapy (aPDT) using the blue diode laser (BDL) with different output powers and the photosensitizers riboflavin and curcumin on reducing the number of Streptococcus mutans around orthodontic brackets. MATERIALS AND METHODS: A total of 36 orthodontic brackets were contaminated with S. mutans and randomly assigned to 12 groups as follows: control, riboflavin alone, riboflavin + BDL with an output power of 200, 300, 400, or 500 mW, and curcumin alone, curcumin + BDL with an output power of 200, 300, 400, or 500 mW, and 0.2% chlorhexidine (CHX-positive control). Orthodontic brackets were irradiated with a BDL (wavelength 445 nm) at a power density of 0.4-1.0 W/cm2 for 30 s. All orthodontic brackets were examined under a stereomicroscope at 10× magnification. Mean colony-forming units (CFUs)/mL were measured before and after treatment. A one-way analysis of variance with Tukey's post hoc test was performed to compare CFU/mL between groups. RESULTS: CHX and curcumin plus BDL with an output power of 500 mW had the highest reduction in S. mutans colony numbers (p < 0.001). The curcumin groups were more effective than the riboflavin groups. Riboflavin alone and riboflavin + BDL with an output power of 200 mW showed no significant difference from the control group (p = 0.99 and 0.74, respectively). CONCLUSION: Our results suggest that aPDT using curcumin as a photosensitizer plus BDL with an output power of 500 mW and a power density of 1.0 W/cm2 at a wavelength of 445 nm can effectively reduce colonies of S. mutans around stainless steel brackets.

Antibacterial potential of riboflavin mediated blue diode laser photodynamic inactivation against Enterococcus faecalis: A laboratory investigation.

OBJECTIVES: This study aimed to evaluate the inactivation potency of riboflavin-mediated blue diode laser photodynamic inactivation (PDI) against Enterococcus faecalis at planktonic and biofilm stages and also investigated its effect on the tooth color change. MATERIALS AND METHODS: The antibacterial and antibiofilm activities of riboflavin mediated PDI against E. faecalis were investigated. The numbers of colony-forming units (CFUs)/mL were calculated. Teeth discoloration were evaluated using the CIE L*a*b* based color difference (ΔE). RESULTS: Antibacterial analysis indicated that the blue diode laser irradiation at 12, 18, 24, and 30 J/cm2 alone and different concentrations of riboflavin solution (6.25 to 100 µM) reduced the number of CFU/mL of E. faecalis, but the reduction was not statistically significant (P > 0.05). Depending on the riboflavin concentration and the light dose, there can be as much as a 1-log effect on CFU/mL. In addition, E. faecalis biofilm was more affected with 30 J/cm2 irradiation dosage and 100 µM riboflavin than other groups. Meanwhile, bacterial suspensions treated with 5.25% sodium hypochlorite (NaOCl) showed maximum biofilm inhibition and colony number reduction, compared with the control. The teeth exhibited clinically acceptable color change after riboflavin treatment at concentration ranging from 6.25 to 50 µM (ΔE < 3.7). CONCLUSIONS: The riboflavin mediated PDI process is somewhat less effective than NaOCl but perhaps less toxic to tissues. It might be feasible to repeat the riboflavin + light treatment to further promote efficacy.

The influence of different mode of power density during antimicrobial photodynamic therapy for photokilling of Streptococcus mutans.

BACKGROUND: The aim of this study was to evaluate the inactivation potency of riboflavin and curcumin plus blue diode laser against Streptococcus mutans with different power densities. MATERIALS AND METHODS: In this in vitro study, standard-strain S. mutans was exposed to curcumin and riboflavin plus blue diode laser with different power densities (0.4-1.0 W/cm2) as well as chlorhexidine (CHX). The colony forming units (CFUs)/mL was calculated. Data were analyzed by one-way ANOVA. RESULTS: Antibacterial analysis indicated that the blue diode laser irradiation with curcumin and riboflavin provided a satisfactory reduction of the S. mutans level. In addition, S. mutans was more affected by curcumin + blue diode laser when the power density was set to 1.0 W/cm2 (P < 0.0001). Meanwhile, bacterial suspensions treated with CHX showed maximum colony number reduction, compared with the control (P < 0.0001). CONCLUSION: This study showed the blue diode laser along with curcumin had strong bactericidal effect on S. mutans, and this effect improved by increasing the power density.

In Vitro Assessment of SWEEPS and Antimicrobial Photodynamic Therapy Alone or in Combination for Eradicating Enterococcus faecalis Biofilm in Root Canals.

OBJECTIVES: This study investigates the efficacy of antimicrobial photodynamic therapy (aPDT) using riboflavin and a blue diode laser (BDL), combined with shock wave-enhanced emission photoacoustic streaming (SWEEPS), against Enterococcus faecalis. MATERIALS AND METHODS: A total of 48 extracted single-rooted human teeth were used. The root canals were instrumented, sealed at their apices, had the smear layer removed, and then underwent autoclave sterilization. Subsequently, each canal was inoculated with E. faecalis bacterial suspension and allowed to incubate for ten days. After confirming the presence of biofilms through scanning electron microscopy (SEM) in three teeth, the remaining teeth were randomly allocated into nine groups, each containing five teeth: control, 5.25% sodium hypochlorite (NaOCl), BDL, SWEEPS + normal saline, SWEEPS + NaOCl, riboflavin, riboflavin + SWEEPS, riboflavin + BDL, and riboflavin + BDL + SWEEPS. After the treatment, the numbers of colony-forming units (CFUs)/mL were calculated. The data were analysed using one-way ANOVA followed by Tukey's test for comparisons. RESULTS: All groups, with the exception of the BDL group, exhibited a significant reduction in E. faecalis CFU/mL when compared to the control group (p < 0.001). The difference in CFU/mL value between riboflavin + BDL + SWEEPS and riboflavin + SWEEPS was significant (p = 0.029), whereas there was no significant difference between riboflavin + BDL + SWEEPS and riboflavin + BDL (p = 0.397). Moreover, there was no statistically significant difference between the riboflavin + SWEEPS group and the riboflavin + BDL group (p = 0.893). CONCLUSIONS: The results demonstrated that combining the SWEEPS technique with riboflavin as a photosensitizer activated by BDL in aPDT effectively reduced the presence of E. faecalis in root canals.

Efficacy and safety of a novel 450 nm blue diode laser versus plasmakinetic electrocautery for the transurethral resection of non-muscle invasive bladder cancer: The protocol and result of a multicenter randomized controlled trial.

Objectives: To be the first to apply a novel 450 nm blue diode laser in transurethral resection of bladder tumor (TURBt) to treat patients with non-muscle invasive bladder cancer (NMIBC) and evaluate its efficacy and safety during the preoperative period compared to the conventional plasmakinetic electrocautery. Materials and Methods: Randomized controlled trial (RCT) in five medical centers was designed as a non-inferiority study and conducted from October 2018 to December 2019. Patients with NMIBC were randomized to the blue laser or plasmakinetic electrocautery group for TURBt. As the first study to evaluate this novel blue laser device, the primary outcome was the effective resection rate of bladder tumors, including effective dissection and hemostasis. The secondary outcomes were the perioperative records, including surgical time, postoperative indwelling catheter time, hospital stay length, blood loss, reoperation rate, wound healing and adverse events. Results: A total of 174 patients were randomized to either the blue laser group (85 patients) or plasmakinetic electrocautery group (89 patients). There was no statistical significance in the clinical features of bladder tumors, including tumor site, number and maximum lesion size. Both the blue laser and plasmakinetic electrocautery could effectively dissect all visible bladder tumors. The surgical time for patients in the blue laser group was longer (p=0.001), but their blood loss was less than that of patients in the control group (p=0.003). There were no differences in the postoperative indwelling catheter time, hospital stay length, reoperation rate or other adverse events. However, the patients undergoing TURBt with the blue laser showed a faster wound healing at 3 months after operation. Conclusion: The novel blue laser could be effectively and safely used for TURBt in patients with NMIBC, and this method was not inferior to plasmakinetic electrocautery during the perioperative period. However, TURBt with the blue laser may provide the benefit to reduce preoperative blood loss and accelerate postoperative wound healing. Moreover, longer follow-up to confirm recurrence-free survival benefit was required.

Comparative Analysis of Vaporization and Coagulation Properties of a Hybrid Laser (Combination of a Thulium and Blue Diode Laser) Vs Thulium and Ho:YAG Lasers: Potential Applications in Endoscopic Enucleation of the Prostate.

Aim: To test the characteristics of a hybrid laser (combination of a thulium and blue diode laser) vs thulium and Ho:YAG lasers regarding soft tissue ablation. Methods: Tissue samples of fresh nonfrozen porcine kidneys were used to compare the three lasers. A motorized translation XY stage with a fixed fiber holder to control the speed of cutting (2 and 5 mm/s) was used. Five incisions with each laser were performed. Lactate dehydrogenase staining of the embedded specimens was performed to determine incision depth, zones of vaporization, coagulation zone, carbonization grade, and thermomechanical damage of the coagulated tissue. All data are expressed as mean ± standard deviation. Results: The hybrid laser demonstrated the highest vaporization speed (34.4 ± 0.1 mm3/s) and coagulation zones (10 ± 0.1 mm2) at a drag speed of 5 mm/s among the investigated lasers. It showed a two to three times larger coagulation zone compared with the Ho:YAG laser (4 ± 0.1 mm2). The continuous wave thulium fiber laser (cwTFL) showed a significantly higher grade of carbonized tissue compared with the hybrid and Ho:YAG lasers. Conclusions: The hybrid laser showed deeper incisions and a faster vaporization speed compared with the cwTFL and the Ho:YAG laser. It might be an effective tool to combine the advantages of both lasers to effectively vaporize soft tissue with excellent coagulative properties.