Using high-resolution imaging to study the impact of the Kalogon wheelchair cushion on blood flow in the gluteal area.

AIM OF THE STUDY: This study investigated how the air-bladder offloading mode of the Orbiter by Kalogon wheelchair cushion (Orbiter) affected blood flow in the gluteal region of non-disabled subjects. The hypothesis was that the cushion's offloading mode would improve blood flow, resulting in reduced reactive hyperemia when compared to the static setting, or Loaded Control (LC). Furthermore, the study proposed a technique using a high-resolution image laser speckle contrast system to measure blood flow in the gluteal area. METHODS: Two procedures were carried out, one with the participant sitting on a cushion in LC, and the second, the cushion was set to offloading mode. Blood flow was measured through data imaging after each procedure. Three trials were performed, starting and ending in different cushion bladders. Customized algorithms were used to select regions of interest on the images for calculations. The Wilcoxon Signed-Rank Test was conducted to compare the offloads and loaded control values of each region of interest. Results were considered significant at α = 0.05. RESULTS: Ten healthy, non-disabled adults participated in the study, seven females and three males. There were no significant differences among the participants. However, results showed that seven subjects tended to decrease reactive hyperemia in the offload sequence of trial when the last two bladders offloaded were the sacrum followed by the right ischial tuberosity. CONCLUSIONS: The high-resolution imager showed that the Orbiter Offloads helped reduce reactive hyperemia in seven subjects, potentially improving blood flow. More research is necessary to comprehend the mechanisms of these effects fully.

Microscopic sensors using optical wireless integrated circuits.

We present a platform for parallel production of standalone, untethered electronic sensors that are truly microscopic, i.e., smaller than the resolution of the naked eye. This platform heterogeneously integrates silicon electronics and inorganic microlight emitting diodes (LEDs) into a 100-µm-scale package that is powered by and communicates with light. The devices are fabricated, packaged, and released in parallel using photolithographic techniques, resulting in ∼10,000 individual sensors per square inch. To illustrate their use, we show proof-of-concept measurements recording voltage, temperature, pressure, and conductivity in a variety of environments.

Soft, skin-interfaced microfluidic systems with integrated immunoassays, fluorometric sensors, and impedance measurement capabilities.

Soft microfluidic systems that capture, store, and perform biomarker analysis of microliter volumes of sweat, in situ, as it emerges from the surface of the skin, represent an emerging class of wearable technology with powerful capabilities that complement those of traditional biophysical sensing devices. Recent work establishes applications in the real-time characterization of sweat dynamics and sweat chemistry in the context of sports performance and healthcare diagnostics. This paper presents a collection of advances in biochemical sensors and microfluidic designs that support multimodal operation in the monitoring of physiological signatures directly correlated to physical and mental stresses. These wireless, battery-free, skin-interfaced devices combine lateral flow immunoassays for cortisol, fluorometric assays for glucose and ascorbic acid (vitamin C), and digital tracking of skin galvanic responses. Systematic benchtop evaluations and field studies on human subjects highlight the key features of this platform for the continuous, noninvasive monitoring of biochemical and biophysical correlates of the stress state.

Absorbing Material of Button Antenna with Directional Radiation of High Gain for P2V Communication.

Vehicular communication systems can be used to enhance the safety level of road users by exchanging safety/warning messages. In this paper, an absorbing material on a button antenna is proposed for pedestrian-to-vehicle (P2V) communication, which provides safety service to road workers on the highway or in a road environment. The button antenna is small in size and is easy to carry for carriers. This antenna is fabricated and tested in an anechoic chamber; it can achieve a maximum gain of 5.5 dBi and an absorption of 92% at 7.6 GHz. The maximum distance of measurement between the absorbing material of the button antenna and the test antenna is less than 150 m. The advantage of the button antenna is that the absorption surface is used in the radiation layer of the antenna so that the antenna can improve the radiation direction and gain. The absorption unit size is 15 × 15 × 5 mm3.

Development and in-vitro characterization of a novel fetal vesicoamniotic shunt - The Vortex shunt.

OBJECTIVES: To develop and test a novel vesicoamniotic shunt (VAS) to treat fetal lower urinary tract obstruction (LUTO), decrease dislodgement and optimize shunt deployment in-vitro. METHODS: Vesicoamniotic shunt design objectives included: (1) robust and atraumatic fixation elements, (2) kink resistant conduit to adjust to fetal movement and growth, (3) one-way pressure valve to facilitate bladder cycling, and (4) echogenic deployment visualization aids. The force to dislodge the novel Vortex shunt was compared with existing commercially available shunts in a bench-top porcine bladder model. Sonographic echogenicity was evaluated with ultrasound-guided deployment, and the shunt valve pressure measured. RESULTS: A prototype novel Vortex shunt was developed using braided nitinol "umbrella-type" ends with a kink-resistant stem incorporating an internal one-way valve. The peak force required to dislodge the Vortex shunt was significantly higher than commercially available shunts (p < 0.01). Shunt deployment in the bench-top model was easily confirmed with ultrasound guidance and the brisk decompression of the inflated porcine bladder thereafter. In-vitro valve gauge pressure testing mirrored bladder pressures in human LUTO cases. CONCLUSION: In-vitro testing shows that the Vortex shunt may improve deployment, sonographic visualization, kink resistance, and dynamic size adjustment. Validation in preclinical animal models are warranted and currently underway.

Precision magnetic field modelling and control for wearable magnetoencephalography.

Optically-pumped magnetometers (OPMs) are highly sensitive, compact magnetic field sensors, which offer a viable alternative to cryogenic sensors (superconducting quantum interference devices - SQUIDs) for magnetoencephalography (MEG). With the promise of a wearable system that offers lifespan compliance, enables movement during scanning, and provides higher quality data, OPMs could drive a step change in MEG instrumentation. However, this potential can only be realised if background magnetic fields are appropriately controlled, via a combination of optimised passive magnetic screening (i.e. enclosing the system in layers of high-permeability materials), and electromagnetic coils to further null the remnant magnetic field. In this work, we show that even in an OPM-optimised passive shield with extremely low (<2 nT) remnant magnetic field, head movement generates significant artefacts in MEG data that manifest as low-frequency interference. To counter this effect we introduce a magnetic field mapping technique, in which the participant moves their head to sample the background magnetic field using a wearable sensor array; resulting data are compared to a model to derive coefficients representing three uniform magnetic field components and five magnetic field gradient components inside the passive shield. We show that this technique accurately reconstructs the magnitude of known magnetic fields. Moreover, by feeding the obtained coefficients into a bi-planar electromagnetic coil system, we were able to reduce the uniform magnetic field experienced by the array from a magnitude of 1.3±0.3 nT to 0.29±0.07 nT. Most importantly, we show that this field compensation generates a five-fold reduction in motion artefact at 0‒2 Hz, in a visual steady-state evoked response experiment using 6 Hz stimulation. We suggest that this technique could be used in future OPM-MEG experiments to improve the quality of data, especially in paradigms seeking to measure low-frequency oscillations, or in experiments where head movement is encouraged.

Measuring functional connectivity with wearable MEG.

Optically-pumped magnetometers (OPMs) offer the potential for a step change in magnetoencephalography (MEG) enabling wearable systems that provide improved data quality, accommodate any subject group, allow data capture during movement and potentially reduce cost. However, OPM-MEG is a nascent technology and, to realise its potential, it must be shown to facilitate key neuroscientific measurements, such as the characterisation of brain networks. Networks, and the connectivities that underlie them, have become a core area of neuroscientific investigation, and their importance is underscored by many demonstrations of their disruption in brain disorders. Consequently, a demonstration of network measurements using OPM-MEG would be a significant step forward. Here, we aimed to show that a wearable 50-channel OPM-MEG system enables characterisation of the electrophysiological connectome. To this end, we measured connectivity in the resting state and during a visuo-motor task, using both OPM-MEG and a state-of-the-art 275-channel cryogenic MEG device. Our results show that resting-state connectome matrices from OPM and cryogenic systems exhibit a high degree of similarity, with correlation values >70%. In addition, in task data, similar differences in connectivity between individuals (scanned multiple times) were observed in cryogenic and OPM-MEG data, again demonstrating the fidelity of the OPM-MEG device. This is the first demonstration of network connectivity measured using OPM-MEG, and results add weight to the argument that OPMs will ultimately supersede cryogenic sensors for MEG measurement.

Innovations in Ventricular Assist Devices for End-Stage Heart Failure.

The number of patients with end-stage heart failure (HF) continues to increase over time, but there has been little change in the availability of organs for cardiac transplantation, intensifying the demand for left ventricular assist devices (LVADs) as a bridge to transplantation. There is also a growing number of patients with end-stage HF who are not transplant candidates but may be eligible for long-term support with an LVAD, known as destination therapy. Due to this increasing demand, LVAD technology has evolved, resulting in transformative improvements in outcomes. Additionally, with growing clinical experience patient management continues to be refined, leading to iterative improvements in outcomes. With outcomes continuing to improve, the potential benefit from LVAD therapy is being considered for patients earlier in their course of advanced HF. We review recent changes in technology, patient management, and implant decision making in LVAD therapy.

96-Well Oxygen Control Using a 3D-Printed Device.

Oxygen concentration varies tremendously within the body and has proven to be a critical variable in cell differentiation, proliferation, and drug metabolism among many other physiological processes. Currently, researchers study the gas's role in biology using low-throughput gas control incubators or hypoxia chambers in which all cells in a vessel are exposed to a single oxygen concentration. Here, we introduce a device that can simultaneously deliver 12 unique oxygen concentrations to cells in a 96-well plate and seamlessly integrate into biomedical research workflows. The device inserts into 96-well plates and delivers gas to the headspace, thus avoiding undesirable contact with media. This simple approach isolates each well using gas-tight pressure-resistant gaskets effectively creating 96 "mini-incubators". Each of the 12 columns of the plate is supplied by a distinct oxygen concentration from a gas-mixing gradient generator supplied by two feed gases. The wells within each column are then supplied by an equal flow-splitting distribution network. Using equal feed flow rates, concentrations ranging from 0.6 to 20.5% were generated within a single plate. A549 lung carcinoma cells were then used to show that O2 levels below 9% caused a stepwise increase in cell death for cells treated with the hypoxia-activated anticancer drug tirapirizamine (TPZ). Additionally, the 96-well plate was further leveraged to simultaneously test multiple TPZ concentrations over an oxygen gradient and generate a three-dimensional (3D) dose-response landscape. The results presented here show how microfluidic technologies can be integrated into, rather than replace, ubiquitous biomedical labware allowing for increased throughput oxygen studies.

Elastomeric Respirators for COVID-19 and the Next Respiratory Virus Pandemic: Essential Design Elements.

Respiratory viruses are transmitted via respiratory particles that are emitted when people breath, speak, cough, or sneeze. These particles span the size spectrum from visible droplets to airborne particles of hundreds of nanometers. Barrier face coverings ("cloth masks") and surgical masks are loose-fitting and provide limited protection from airborne particles since air passes around the edges of the mask as well as through the filtering material. Respirators, which fit tightly to the face, provide more effective respiratory protection. Although healthcare workers have relied primarily on disposable filtering facepiece respirators (such as N95) during the COVID-19 pandemic, reusable elastomeric respirators have significant potential advantages for the COVID-19 and future respiratory virus pandemics. However, currently available elastomeric respirators were not designed primarily for healthcare or pandemic use and require further development to improve their suitability for this application. The authors believe that the development, implementation, and stockpiling of improved elastomeric respirators should be an international public health priority.

Increasing the Microfabrication Performance of Synthetic Hydrogel Precursors through Molecular Design.

Implementation of hydrogel precursors in two-photon polymerization (2PP) technology provides promising opportunities in the tissue engineering field thanks to their soft characteristics and similarity to extracellular matrix. Most of the hydrogels, however, are prone to post-fabrication deformations, leading to a mismatch between the computer-aided design and the printed structure. In the present work, we have developed novel synthetic hydrogel precursors to overcome the limitations associated with 2PP processing of conventional hydrogel precursors such as post-processing deformations and a narrow processing window. The precursors are based on a poly(ethylene glycol) backbone containing urethane linkers and are, on average, functionalized with six acrylate terminal groups (three on each terminal group). As a benchmark material, we exploited a precursor with an identical backbone and urethane linkers, albeit functionalized with two acrylate groups, that were reported as state-of-the-art. An in-depth characterization of the hexafunctional precursors revealed a reduced swelling ratio (<0.7) and higher stiffness (>36 MPa Young's modulus) compared to their difunctional analogs. The superior physical properties of the newly developed hydrogels lead to 2PP-based fabrication of stable microstructures with excellent shape fidelity at laser scanning speeds up to at least 90 mm s-1, in contrast with the distorted structures of conventional difunctional precursors. The hydrogel films and microscaffolds revealed a good cell interactivity after functionalization of their surface with a gelatin methacrylamide-based coating. The proposed synthesis strategy provides a one-pot and scalable synthesis of hydrogel building blocks that can overcome the current limitations associated with 2PP fabrication of hydrogel microstructures.

Advancement of the Infant Air-Jet Dry Powder Inhaler (DPI): Evaluation of Different Positive-Pressure Air Sources and Flow Rates.

PURPOSE: In order to improve the delivery of dry powder aerosol formulations to the lungs of infants, this study implemented an infant air-jet platform and explored the effects of different air sources, flow rates, and pulmonary mechanics on aerosolization performance and aerosol delivery through a preterm nose-throat (NT) in vitro model. METHODS: The infant air-jet platform was actuated with a positive-pressure air source that delivered the aerosol and provided a full inhalation breath. Three different air sources were developed to provide highly controllable positive-pressure air actuations (using actuation volumes of ~10 mL for the preterm model). While providing different flow waveform shapes, the three air sources were calibrated to produce the same flow rate magnitude (Q90: 90th percentile of flow rate). Multiple air-jet DPI designs were coupled with the air sources and evaluated with a model spray-dried excipient enhanced growth formulation. RESULTS: Compared to other designs, the D1-Single air-jet DPI provided improved performance with low variability across all three air sources. With the tested D1-Single air-jet and Timer air source, reducing the flow rate from 4 to 1.7 L/min marginally decreased the aerosol size and significantly increased the lung delivery efficiency above 50% of the loaded dose. These results were not impacted by the presence of downstream pulmonary mechanics (resistance and compliance model). CONCLUSIONS: The selected design was capable of providing an estimated >50% lung delivery efficiency of a model spray-dried formulation and was not influenced by the air source, thereby enabling greater flexibility for platform deployment in different environments.

Using Filters to Estimate Regional Lung Deposition with Dry Powder Inhalers.

PURPOSE: To develop an in vitro method to rapidly evaluate regional lung doses delivered by pharmaceutical inhalers. Currently, cascade impactor measurements are used, but these are resource intensive and require significant post processing of in vitro data to arrive at regional deposition estimates. METHODS: We present a specialized filter apparatus that mimics tracheobronchial (TB) deposition of pharmaceutical aerosols emitted by commercially available dry powder inhalers (DPIs). The filter housing includes an electrostatic neutralizer to eliminate artificial electrostatic filtration effects. Regional deposition (tracheobronchial and alveolar) for four DPIs (Onbrez Breezhaler, Flovent Diskus, Pulmicort Turbuhaler, and Asmanex Twisthaler) was estimated using cascade impactor measurements and an in silico regional deposition model. These estimates were compared to direct measurements of regional deposition as provided by the TB filter mimic and an absolute filter placed downstream of the TB filter housing, representing the alveolar dose. RESULTS: The two methods were shown to provide similar estimates of extrathoracic, tracheobronchial, and alveolar deposition, as well as total recovery of active pharmaceutical ingredients. CONCLUSIONS: Because of its design, the TB filter apparatus makes it possible to estimate regional deposition with inhalers directly using variable inhalation profiles without any additional equipment or changes to the experimental configuration. This method may be useful to expedite development of both innovative and generic drug products as it provides regional respiratory tract deposition estimates using fewer resources than exisiting methods.

Supercritical angle fluorescence for enhanced axial sectioning in STED microscopy.

We demonstrate subwavelength axial sectioning on biological samples with a stimulated emission depletion (STED) microscope combined with supercritical angle fluorescence (SAF) detection. SAF imaging is a powerful technique for imaging the membrane of the cell based on the direct exploitation of the fluorophore emission properties. Indeed, only when fluorophores are close to the interface can their evanescent near-field emission become propagative and be detected beyond the critical angle. Therefore, filtering out the SAF emission from the undercritical angle fluorescence (UAF) emission in the back focal plane of a high-NA objective lens permits nanometer axial sectioning of fluorescent emitters close to the coverslip. When combined with STED microscopy, a straightforward gain in axial resolution can be reached without any alteration of the STED beam path. Indeed, STED-SAF implementation only requires a modification in the detection path of the STED microscope and thus could be widely implemented.

Difficulty in Advancing Flexible Epidural Catheters When Establishing Labor Analgesia: An Observational Open-Label Randomized Trial.

BACKGROUND: While flexible epidural catheters reduce the risk of paresthesia and intravascular cannulation, they may be more challenging to advance beyond the tip of a Tuohy needle. This may increase placement time, number of attempts, and possibly complications when establishing labor analgesia. This study investigated the ability to advance flexible epidural catheters through different epidural needles from 2 commonly used, commercially available, epidural kits. METHODS: We hypothesized that the multiorifice wire-reinforced polyamide nylon blend epidural catheters will have a higher rate of successful first attempt insertion than the single-end hole wire-reinforced polyurethane catheters for the establishment of labor analgesia. The primary outcome was a difference in proportions of failure to advance the epidural catheter between the 2 epidural kits and was tested by a χ2 test. Two-hundred forty epidural kits were collected (n = 120/group) for 240 laboring patients requesting epidural analgesia in this open-label clinical trial from November 2018 to September 2019. Two-week time intervals were randomized for the exclusive use of 1 of the 2 kits in this study, where all patients received labor analgesia through either the flexible epidural catheter "A" or the flexible epidural catheter "B." Engineering properties of the equipment used were then determined. RESULTS: Flexible epidural catheter "A," the single-end hole wire-reinforced polyurethane catheter, did not advance at the first attempt in 15% (n = 18 of 120) of the parturients compared to 0.8% (n = 1 of 120) of the catheter "B," the multiorifice wire-reinforced polyamide nylon blend epidural catheter (P < .0001). Twenty-five additional epidural needle manipulations were recorded in the laboring patients who received catheter "A," while 1 epidural needle manipulation was recorded in the parturients who received catheter "B" (P < .0001). Bending stiffness of the epidural catheters used from kit "B" was twice the bending stiffness of the catheters used from kit "A" (bending stiffness catheters "A" 0.64 ± 0.04 N·mm2 versus bending stiffness catheters "B" 1.28 ± 0.20 N·mm2, P = .0038), and the angle formed by the needle and the epidural catheter from kit "A" was less acute than the angle formed from kit "B" (kit "A" 14.17 ± 1.72° versus kit "B" 21.83 ± 1.33°, P = .0036), with a mean difference of 7.66° between the 2 kits' angles. CONCLUSIONS: The incidence of an inability to advance single-end hole wire-reinforced polyurethane catheter was higher compared to the use of multiorifice wire-reinforced polyamide nylon blend epidural catheter. Variation of morphological features of epidural needles and catheters may play a critical role in determining the successful establishment of labor epidural analgesia.

Controlling Anesthesia Hardware With Simple Hand Gestures: Thumbs Up or Thumbs Down?

BACKGROUND: Modern consumer electronic devices and automobiles are often controlled by interfaces that sense physical gestures and spoken commands. In contrast, patient monitors and anesthesia devices are typically equipped with panel-mounted buttons, dials, and keyboards. The increased use of noncontact gesture-based interfaces in anesthesia may improve patient safety through more intuitive and prompter control of equipment and also through reduced rates of surface contamination. A novel gesture-based controller was designed and retrofitted to a standard GE Solar 8000M patient monitor. This type of technical innovation is rare, due to closely held proprietary input control systems on commercially produced clinical equipment. Nevertheless, we hypothesized that anesthesiologists would find a contactless gesture interface straightforward to use. METHODS: A gesture-based interface system was developed to control a Solar 8000M patient monitor using a millimeter-wave radar sensor. The system was programmed to detect noncontact "rotate" and "press" gestures to control the patient monitor by implementing a virtual trim knob for interface control. Fifty anesthesiologists tested a prototype interface and evaluated usability by completing a short questionnaire incorporating modified Likert scales. These evaluations were performed in a nonpatient care environment so that respondents were not adversely task loaded during assessment, also allaying any ethical or safety concerns regarding use of this novel interface for patient management. RESULTS: Anesthesia hardware was controlled reliably with 2 distinct gestures above the gesture sensor. The gesture-based interface generally was well received by anesthesiologists (8.09; confidence interval, 8.06-8.12 on a 10-point scale), who preferred the simpler "press" gesture to the "rotate" gesture (8.45; 8.39-8.51 vs 7.73; 7.67-7.79 on a 10-point scale; P = .005). The correlation between the preference scores for the 2 gestures from each anesthesiologist was strong (Pearson r = 0.49; 0.25-0.68; P < .001). Advancing level of training (resident, fellow, attending 1-10 years, attending >10 years) was not correlated with preference scores for either gesture (Spearman ρ = -0.02; -0.30 to 0.26; P = .87 for "press" and Spearman ρ = 0.08; -0.20 to 0.35; P = .58 for "rotate"). CONCLUSIONS: The use of gesture sensing for controlling anesthesia equipment was well received by a cohort of anesthesiologists. Even though the simpler "press" gesture was preferred over the "rotate" gesture, the intrarespondent correlation indicates that the preference for gestures as a whole is the stronger effect. No adverse relationship was found between acceptability and anesthesia experience level. Gesture sensing is a promising new area to simplify and improve the interaction between the anesthesiologist and the anesthesia workstation.

Determination of local flow ratios and velocities in a femoral venous cannula with computational fluid dynamics and 4D flow-sensitive magnetic resonance imaging: A method validation.

Cannulas with multi-staged side holes are the method of choice for femoral cannulation in extracorporeal therapies today. A variety of differently designed products is available on the market. While the preferred tool for the performance assessment of such cannulas are pressure-flow curves, little is known about the flow and velocity distribution. Within this work flow and velocity patterns of a femoral venous cannula with multi-staged side holes were investigated. A mock circulation loop for cannula performance evaluation was built and reproduced using a computer-aided design system. With computational fluid dynamics, volume flows and fluid velocities were determined quantitatively and visually with hole-based precision. In order to ensure the correctness of the flow simulation, the results were subsequently validated by determining the same parameters with four-dimensional flow-sensitive magnetic resonance imaging. Measurement data and numerical solution differed 7% on average throughout the data set for the examined parameters. The highest inflow and velocity were detected at the most proximal holes, where half of the total volume flow enters the cannula. At every hole stage a Y-shaped inflow profile was detected, forming a centered stream in the middle of the cannula. Simultaneously, flow separation creates zones with significant lower flow velocities. Numerical simulation, validated with four-dimensional flow-sensitive magnetic resonance imaging, is a valuable tool to examine flow and velocity distributions of femoral venous cannulas with hole-based accuracy. Flow and velocity distribution in such cannulas are not ideal. Based on this work future cannulas can be effectively optimized.

A 3-dimensional-printed left ventricle model incorporated into a mock circulatory loop to investigate hemodynamics inside a severely failing ventricle supported by a blood pump.

Intraventricular blood stasis is a design consideration for continuous flow blood pumps and might contribute to adverse events such as thrombosis and ventricular suction. However, the blood flow inside left ventricles (LVs) supported by blood pumps is still unclear. In vitro experiments were conducted to imitate how the hydraulic performance of an axial blood pump affects the intraventricular blood flow of a severe heart failure patient, such as velocity distribution, vorticity, and standard deviation of velocity. In this study, a silicone model of the LV was constructed from the computed tomography data of one patient with heart failure and was 3D printed. Then, intraventricular flow was visualized by particle image velocimetry equipment within a mock circulation loop. The results showed that the axial blood pump suctions most of the blood in a severely failing LV, there was an altered flow status within the LV, and blood stasis appeared in the central region of the LV. Some blood may be suctioned from the aortic valve to the blood pump because the patient's native heart was severely failing. Blood stasis at the LV center may cause thrombosis in the LV. The vortex flow near the inner wall of the LV can thoroughly wash the left ventricular cavity.

Smooth multifocal wavefronts with a prescribed mean curvature for visual optics applications.

Multifocal lenses comprising progressive power surfaces are commonly used in contact and intraocular lens designs. Given a visual performance metric, a wavefront engineering approach to design such lenses is based on searching for the optimal wavefront at the exit pupil of the eye. Multifocal wavefronts distribute the energy along the different foci thanks to having a varying mean curvature. Therefore, a fundamental step in the wavefront engineering approach is to generate the wavefront from a prescribed mean curvature function. Conventionally, such a thing is done by superimposing spherical wavefront patches and maybe adding a certain component of spherical aberration to each spherical patch in order to increase the depth-of-field associated with each focus. However, such a procedure does not lead to smooth wavefront solutions and also restricts the type of available multifocal wavefronts. We derive a new, to the best of our knowledge, mathematical method to uniquely construct multifocal wavefronts from mean curvature functions (depending on radial and angular coordinates) under certain numerically justified approximations and restrictions. Additionally, our procedure leads to a particular family of wavefronts (line-umbilical multifocal wavefronts) described by 2 conditions: (1) to be smooth multiplicative separable functions in the radial and angular coordinates; (2) to be umbilical along a specific segment connecting the circle center with its edge. We provide several examples of multifocal wavefronts belonging to this family, including a smooth variant of the so-called light sword element.

A hand exercise mobile app for people with rheumatoid arthritis in Turkey: design, development and usability study.

To design and develop a smartphone application for a structured hand exercise programme for patients with rheumatoid arthritis (RA) in Turkey and to test its usability. We followed a two-stage process: (1) Design and Development and (2) Usability testing. In stage 1, we used a qualitative user-centered design approach. We conducted a focus group (8 therapists and people with RA) to discuss the content, features and design to produce a prototype of the application. In a second focus group session, the participants tested the prototype, provided feedback and further revisions were made. In stage 2, 17 participants with RA used the app for 4 to 6 weeks. The System Usability Scale and the adapted Usability, Satisfaction and Ease to Use Questionnaires were used to measure usability, ease of use. Semi-structured interviews were conducted to explore user experiences with the application with 17 participants. In stage 1, the following themes were identified from the focus groups (a) login techniques (b) self-monitoring (c) exercises, (d) exercise diary, (e) information, (f) behavioral change and encouragement (g) exercise adherence. In stage 2, 3 themes were determined from interviews: (a) learning and accuracy, (b) ease of use, (c) motivation and adherence. USE and SUS scores indicated that users reported a high level of usability, satisfaction and ease of use. A mobile app for hand exercise for people with RA was developed using a mixed-method and iterative design. Participants perceived the mobile app as easy to use with high levels of satisfaction.