Controlling scaffold conductivity and pore size to direct myogenic cell alignment and differentiation.

Skeletal muscle's combination of three-dimensional (3D) anisotropy and electrical excitability is critical for enabling normal movement. We previously developed a 3D aligned collagen scaffold incorporating conductive polypyrrole (PPy) particles to recapitulate these key muscle properties and showed that the scaffold facilitated enhanced myotube maturation compared with nonconductive controls. To further optimize this scaffold design, this work assessed the influence of conductive polymer incorporation and scaffold pore architecture on myogenic cell behavior. Conductive PPy and poly(3,4-ethylenedioxythiophene) (PEDOT) particles were synthesized and mixed into a suspension of type I collagen and chondroitin sulfate prior to directional freeze-drying to produce anisotropic scaffolds. Energy dispersive spectroscopy revealed homogenous distribution of conductive PEDOT particles throughout the scaffolds that resulted in a threefold increase in electrical conductivity while supporting similar myoblast metabolic activity compared to nonconductive scaffolds. Control of freezing temperature enabled fabrication of PEDOT-doped scaffolds with a range of pore diameters from 98 to 238 µm. Myoblasts conformed to the anisotropic contact guidance cues independent of pore size to display longitudinal cytoskeletal alignment. The increased specific surface area of the smaller pore scaffolds helped rescue the initial decrease in myoblast metabolic activity observed in larger pore conductive scaffolds while also promoting modestly increased expression levels of the myogenic marker myosin heavy chain (MHC) and gene expression of myoblast determination protein (MyoD). However, cell infiltration to the center of the scaffolds was marginally reduced compared with larger pore variants. Together these data underscore the potential of aligned and PEDOT-doped collagen scaffolds for promoting myogenic cell organization and differentiation.

Photoreactive Hydrogel Stiffness Influences Volumetric Muscle Loss Repair.

Volumetric muscle loss (VML) injuries are characterized by permanent loss of muscle mass, structure, and function. Hydrogel biomaterials provide an attractive platform for skeletal muscle tissue engineering due to the ability to easily modulate their biophysical and biochemical properties to match a range of tissue characteristics. In this work, we successfully developed a mechanically tunable hyaluronic acid (HA) hydrogel system to investigate the influence of hydrogel stiffness on VML repair. HA was functionalized with photoreactive norbornene groups to create hydrogel networks that rapidly crosslink through thiol-ene click chemistry with tailored mechanics. Mechanical properties were controlled by modulating the amount of matrix metalloproteinase-degradable peptide crosslinker to produce hydrogels with increasing elastic moduli of 1.1 ± 0.002, 3.0 ± 0.002, and 10.6 ± 0.006 kPa, mimicking a relevant range of developing and mature muscle stiffnesses. Functional muscle recovery was assessed following implantation of the HA hydrogels by in situ photopolymerization into rat latissimus dorsi (LD) VML defects at 12 and 24 weeks postinjury. After 12 weeks, muscles treated with medium stiffness (3.0 kPa) hydrogels produced maximum isometric forces most similar to contralateral healthy LD muscles. This trend persisted at 24 weeks postinjury, suggestive of sustained functional recovery. Histological analysis revealed a significantly larger zone of regeneration with more de novo muscle fibers following implantation of medium stiffness hydrogels in VML-injured muscles compared to other experimental groups. Lower (low and medium) stiffness hydrogels also appeared to attenuate the chronic inflammatory response characteristic of VML injuries, displaying similar levels of macrophage infiltration and polarization to healthy muscle. Together these findings illustrate the importance of hydrogel mechanical properties in supporting functional repair of VML injuries. Impact statement This report defines the role hydrogel mechanical properties play in the repair of volumetric muscle loss (VML) injuries. We show that an intermediate hydrogel stiffness (3 kPa) more compliant than adult muscle tissue facilitated improved and sustained regenerative outcomes up to 24 weeks postinjury in a rat latissimus dorsi model of VML. Muscles treated with 3 kPa hydrogels showed enhanced myogenesis and attenuation of the chronic inflammatory response characteristic of VML injuries. These results should help guide the future design of hydrogels for skeletal muscle tissue engineering and regeneration.

Aligned and electrically conductive 3D collagen scaffolds for skeletal muscle tissue engineering.

Skeletal muscle is characterized by its three-dimensional (3D) anisotropic architecture composed of highly aligned and electrically-excitable muscle fibers that enable normal movement. Biomaterial-based tissue engineering approaches to repair skeletal muscle are limited due to difficulties combining 3D structural alignment (to guide cell/matrix organization) and electrical conductivity (to enable electrically-excitable myotube assembly and maturation). In this work we successfully produced aligned and electrically conductive 3D collagen scaffolds using a freeze-drying approach. Conductive polypyrrole (PPy) nanoparticles were synthesized and directly mixed into a suspension of type I collagen and chondroitin sulfate followed by directional lyophilization. Scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and confocal microscopy showed that directional solidification resulted in scaffolds with longitudinally aligned pores with homogeneously-distributed PPy content. Chronopotentiometry verified that PPy incorporation resulted in a five-fold increase in conductivity compared to non-PPy-containing collagen scaffolds without detrimentally affecting myoblast metabolic activity. Furthermore, the aligned scaffold microstructure provided contact guidance cues that directed myoblast growth and organization. Incorporation of PPy also promoted enhanced myotube formation and maturation as measured by myosin heavy chain (MHC) expression and number of nuclei per myotube. Together these data suggest that aligned and electrically conductive 3D collagen scaffolds could be useful for skeletal muscle tissue engineering.