AgIn5S8/ZnS Quantum Dots for Luminescent Down-Shifting and Antireflective Layer in Enhancing Photovoltaic Performance.

Colloidal AgIn5S8/ZnS quantum dots (QDs) have recently emerged as a promising, efficient, nontoxic, down-shifting material in optoelectronic devices. These QDs exhibit a high photoluminescent quantum yield and offer a range of potential applications, specifically in the field of photovoltaics (PVs) for light management. In this work, we report an eco-friendly method to synthesize AgIn5S8/ZnS QDs and deposit them on commercial silicon solar cells (with an active area of 7.5 cm2), with which the short-circuit current (JSC) enhanced by 1.44% and hence the power conversion efficiency by 2.51%. The enhancements in PV performance are mainly attributable to the improved external quantum efficiency in the ultraviolet region and reduced surface reflectance in the ultraviolet and near-infrared regions. We study the effect of QD concentration on the bifunctions of downshifting and antireflection. The optimal 15 mg/mL QDs blade-coated onto the Si solar cells realize maximum current generation as the reflectance loss in the visible wavelength is compensated by the minimized reflection in the near-infrared region.

Single Crystalline Films of Ce3+-Doped Y3MgxSiyAl5-x-yO12 Garnets: Crystallization, Optical, and Photocurrent Properties.

This research focuses on LPE growth, and the examination of the optical and photovoltaic properties of single crystalline film (SCF) phosphors based on Ce3+-doped Y3MgxSiyAl5-x-yO12 garnets with Mg and Si contents in x = 0-0.345 and y = 0-0.31 ranges. The absorbance, luminescence, scintillation, and photocurrent properties of Y3MgxSiyAl5-x-yO12:Ce SCFs were examined in comparison with Y3Al5O12:Ce (YAG:Ce) counterpart. Especially prepared YAG:Ce SCFs with a low (x, y < 0.1) concentration of Mg2+ and Mg2+-Si4+ codopants also showed a photocurrent that increased with rising Mg2+ and Si4+ concentrations. Mg2+ excess was systematically present in as-grown Y3MgxSiyAl5-x-yO12:Ce SCFs. The as-grown SCFs of these garnets under the excitation of α-particles had a low light yield (LY) and a fast scintillation response with a decay time in the ns range due to producing the Ce4+ ions as compensators for the Mg2+ excess. The Ce4+ dopant recharged to the Ce3+ state after SCF annealing at T > 1000 °C in a reducing atmosphere (95%N2 + 5%H2). Annealed SCF samples exhibited an LY of around 42% and similar scintillation decay kinetics to those of the YAG:Ce SCF counterpart. The photoluminescence studies of Y3MgxSiyAl5-x-yO12:Ce SCFs provide evidence for Ce3+ multicenter formation and the presence of an energy transfer between various Ce3+ multicenters. The Ce3+ multicenters possessed variable crystal field strengths in the nonequivalent dodecahedral sites of the garnet host due to the substitution of the octahedral positions by Mg2+ and the tetrahedral positions by Si4+. In comparison with YAG:Ce SCF, the Ce3+ luminescence spectra of Y3MgxSiyAl5-x-yO12:Ce SCFs greatly expanded in the red region. Using these beneficial trends of changes in the optical and photocurrent properties of Y3MgxSiyAl5-x-yO12:Ce garnets as a result of Mg2+ and Si4+ alloying, a new generation of SCF converters for white LEDs, photovoltaics, and scintillators could be developed.

Micropowder Ca2YMgScSi3O12:Ce Silicate Garnet as an Efficient Light Converter for White LEDs.

This work is dedicated to the crystallization and luminescent properties of a prospective Ca2YMgScSi3O12:Ce (CYMSSG:Ce) micropowder (MP) phosphor converter (pc) for a white light-emitting LED (WLED). The set of MP samples was obtained by conventional solid-phase synthesis using different amounts of B2O3 flux in the 1-5 mole percentage range. The luminescent properties of the CYMSSG:Ce MPs were investigated at different Ce3+ concentrations in the 1-5 atomic percentage range. The formation of several Ce3+ multicenters in the CYMSSG:Ce MPs was detected in the emission and excitation spectra as well as the decay kinetics of the Ce3+ luminescence. The creation of the Ce3+ multicenters in CYMSSG:Ce garnet results from: (i) the substitution by the Ce3+ ions of the heterovalent Ca2+ and Y3+ cations in the dodecahedral position of the garnet host; (ii) the inhomogeneous local environment of the Ce3+ ions when the octahedral positions of the garnet are replaced by heterovalent Mg2+ and Sc3+ cations and the tetrahedral positions are replaced by Si4+ cations. The presence of Ce3+ multicenters significantly enhances the Ce3+ emission band in the red range in comparison with conventional YAG:Ce phosphor. Prototypes of the WLEDs were also created in this work by using CYMSSG:Ce MP films as phosphor converters. Furthermore, the dependence of the photoconversion properties on the layer thickness of the CYMSSG:Ce MP was studied as well. The changes in the MP layer thickness enable the tuning of the white light thons from cold white/daylight to neutral white. The obtained results are encouraging and can be useful for the development of a novel generation of pcs for WLEDs.

Spontaneous alloying of ultrasmall non-stoichiometric Ag-In-S and Cu-In-S quantum dots in aqueous colloidal solutions.

The effect of spontaneous alloying of non-stoichiometric aqueous Ag-In-S (AIS) and Cu-In-S (CIS) quantum dots (QDs) stabilized by surface glutathione (GSH) complexes was observed spectroscopically due to the phenomenon of band bowing typical for the solid-solution Cu(Ag)-In-S (CAIS) QDs. The alloying was found to occur even at room temperature and can be accelerated by a thermal treatment of colloidal mixtures at around 90 °C with no appreciable differences in the average size observed between alloyed and original individual QDs. An equilibrium between QDs and molecular and clustered metal-GSH complexes, which can serve as "building material" for the new mixed CAIS QDs, during the spontaneous alloying is assumed to be responsible for this behavior of GSH-capped ternary QDs. The alloying effect is expected to be of a general character for different In-based ternary chalcogenides.

Looking beyond the Surface: The Band Gap of Bulk Methylammonium Lead Iodide.

Despite the intense research on photovoltaic lead halide perovskites, reported optical properties as basic as the absorption onset and the optical band gap vary significantly. To unambiguously answer the question whether the discrepancies are a result of differences between bulk and "near-surface" material, we perform two nonlinear spectroscopies with drastically different information depths on single crystals of the prototypical (CH3NH3)PbI3 methylammonium lead iodide. Two-photon absorption, detected via the resulting generation of carriers and photocurrents (2PI-PC), probes the interband transitions with an information depth in the millimeter range relevant for bulk (single-crystal) material. In contrast, the transient magneto-optical Kerr effect (trMOKE) measured in a reflection geometry determines the excitonic transition energies in the region near (hundreds of nm) the surface which also determine the optical properties in typical thin films. To identify differences between structural phases, we sweep the sample temperature across the orthorhombic-tetragonal phase transition temperature. In the application-relevant room-temperature tetragonal phase (at 170 K), we find a bulk band gap of 1.55 ± 0.01 eV, whereas in the near-surface region excitonic transitions occur at 1.59 ± 0.01 eV. The latter value is consistent with previous reflectance measurements by other groups and considerably higher than the bulk band gap. The small band gap of the bulk material explains the extended infrared absorption of crystalline perovskite solar cells, the low-energy bands which carry optically driven spin-polarized currents, and the narrow bandwidth of crystalline perovskite photodetectors making use of the spectral filtering at the surface.

Structural fluctuations cause spin-split states in tetragonal (CH3NH3)PbI3 as evidenced by the circular photogalvanic effect.

Lead halide perovskites are used in thin-film solar cells, which owe their high efficiency to the long lifetimes of photocarriers. Various calculations find that a dynamical Rashba effect could significantly contribute to these long lifetimes. This effect is predicted to cause a spin splitting of the electronic bands of inversion-symmetric crystalline materials at finite temperatures, resulting in a slightly indirect band gap. Direct experimental evidence of the existence or the strength of the spin splitting is lacking. Here, we resonantly excite photocurrents in single crystalline ([Formula: see text])[Formula: see text] with circularly polarized light to clarify the existence of spin splittings in the band structure. We observe a circular photogalvanic effect, i.e., the photocurrent depends on the light helicity, in both orthorhombic and tetragonal ([Formula: see text])[Formula: see text] At room temperature, the effect peaks for excitation photon energies [Formula: see text] meV below the direct optical band gap. Temperature-dependent measurements reveal a sign change of the effect at the orthorhombic-tetragonal phase transition, indicating different microscopic origins in the two phases. Within the tetragonal phase, both [Formula: see text] and the amplitude of the circular photogalvanic effect increase with temperature. Our findings support a dynamical Rashba effect in this phase, i.e., a spin splitting caused by thermally induced structural fluctuations which break inversion symmetry.

Improved charge carrier dynamics in polymer/perovskite nanocrystal based hybrid ternary solar cells.

Here, brand new ternary hybrid solar cells comprising perovskite nanocrystals (NCs) with a complementary absorption profile of the organic host matrix are reported. In particular, NH2CH[double bond, length as m-dash]NH2PbI3 (FAPbI3) perovskite NCs are implemented in bulk heterojunction organic solar cells based on the pDPP5T-2 electron donating polymer and a [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) acceptor at various loading amounts and the fabricated hybrid photovoltaics are thoroughly studied by employing different optoelectrical characterization methods. Current-voltage measurements and photoinduced charge carrier extraction by linear increasing voltage (photo-CELIV) reveal improved charge generation and charge transport properties upon incorporation of perovskite NCs into the photo-active layer of the hybrid solar cell. The power conversion efficiency (PCE) of the hybrid solar cell comprising 5% perovskite NCs is 10% enhanced compared to the organic reference, mainly due to the enlarged light harvesting and increased short circuit current density (Jsc). However, results suggest that introducing a higher amount of perovskite content induces bimolecular and trap-assisted recombination in the ternary devices. We perform a comprehensive transient absorption study of the charge transfer/transport mechanisms by employing femto-second pump-probe transient absorption spectroscopy (fs-TAS). fs-TAS measurements demonstrate a slower charge carrier recombination rate due to the introduction of perovskite NCs into the photoactive layer. Results reveal that DPP injects electrons from the singlet excited state into the perovskite NCs, which causes the desired cascading charge carrier transfer. In ternary blends, a small amount of FAPbI3 NCs provides an additional pathway in favor of the charge-separated state via the NCs, which, despite accelerating the depopulation of DPP's singlet excited state slightly slows down the charge-separation process between DPP and PC61BM. Interestingly, the loss processes are slowed down; an effect that is more important and, hence, explains the improved solar cell efficiency.

Brightly Luminescent and Color-Tunable Formamidinium Lead Halide Perovskite FAPbX3 (X = Cl, Br, I) Colloidal Nanocrystals.

In the past few years, hybrid organic-inorganic and all-inorganic metal halide perovskite nanocrystals have become one of the most interesting materials for optoelectronic applications. Here, we report a facile and rapid room temperature synthesis of 15-25 nm formamidinium CH(NH2)2PbX3 (X = Cl, Br, I, or mixed Cl/Br and Br/I) colloidal nanocrystals by ligand-assisted reprecipitation (LARP). The cubic and platelet-like nanocrystals with their emission in the range of 415-740 nm, full width at half-maximum (fwhm) of 20-44 nm, and radiative lifetimes of 5-166 ns enable band gap tuning by halide composition as well as by their thickness tailoring; they have a high photoluminescence quantum yield (up to 85%), colloidal and thermodynamic stability. Combined with surface modification that prevents degradation by water, this nanocrystalline material is an ideal candidate for optoelectronic devices and applications. In addition, optoelectronic measurements verify that the photodetector based on FAPbI3 nanocrystals paves the way for perovskite quantum dot photovoltaics.

Ligand-assisted thickness tailoring of highly luminescent colloidal CH3NH3PbX3 (X = Br and I) perovskite nanoplatelets.

Quantum size-confined CH3NH3PbX3 (X = Br and I) perovskite nanoplatelets with remarkably high photoluminescence quantum yield (up to 90%) were synthesized by ligand-assisted re-precipitation. Thickness-tunability was realized by varying the oleylamine and oleic acid ligand ratio. This method allows tailoring the nanoplatelet thickness by adjusting the number of unit cell monolayers. Broadly tunable emission wavelengths (450-730 nm) are achieved via the pronounced quantum size effect without anion-halide mixing.

Giant Rashba Splitting in CH_{3}NH_{3}PbBr_{3} Organic-Inorganic Perovskite.

As they combine decent mobilities with extremely long carrier lifetimes, organic-inorganic perovskites open a whole new field in optoelectronics. Measurements of their underlying electronic structure, however, are still lacking. Using angle-resolved photoelectron spectroscopy, we measure the valence band dispersion of single-crystal CH_{3}NH_{3}PbBr_{3}. The dispersion of the highest energy band is extracted applying a modified leading edge method, which accounts for the particular density of states of organic-inorganic perovskites. The surface Brillouin zone is consistent with bulk-terminated surfaces both in the low-temperature orthorhombic and the high-temperature cubic phase. In the low-temperature phase, we find a ring-shaped valence band maximum with a radius of 0.043 Å^{-1}, centered around a 0.16 eV deep local minimum in the dispersion of the valence band at the high-symmetry point. Intense circular dichroism is observed. This dispersion is the result of strong spin-orbit coupling. Spin-orbit coupling is also present in the room-temperature phase. The coupling strength is one of the largest ones reported so far.

Solar spectral conversion for improving the photosynthetic activity in algae reactors.

Sustainable biomass production is expected to be one of the major supporting pillars for future energy supply, as well as for renewable material provision. Algal beds represent an exciting resource for biomass/biofuel, fine chemicals and CO2 storage. Similar to other solar energy harvesting techniques, the efficiency of algal photosynthesis depends on the spectral overlap between solar irradiation and chloroplast absorption. Here we demonstrate that spectral conversion can be employed to significantly improve biomass growth and oxygen production rate in closed-cycle algae reactors. For this purpose, we adapt a photoluminescent phosphor of the type Ca0.59Sr0.40Eu0.01S, which enables efficient conversion of the green part of the incoming spectrum into red light to better match the Qy peak of chlorophyll b. Integration of a Ca0.59Sr0.40Eu0.01S backlight converter into a flat panel algae reactor filled with Haematococcus pluvialis as a model species results in significantly increased photosynthetic activity and algae reproduction rate.

Enhanced photosynthetic activity in Spinacia oleracea by spectral modification with a photoluminescent light converting material.

The spectral conversion of incident sunlight by appropriate photoluminescent materials has been a widely studied issue for improving the efficiency of photovoltaic solar energy harvesting. By using phosphors with suitable excitation/emission properties, also the light conditions for plants can be adjusted to match the absorption spectra of chlorophyll dyes, in this way increasing the photosynthetic activity of the plant. Here, we report on the application of this principle to a high plant, Spinacia oleracea. We employ a calcium strontium sulfide phosphor doped with divalent europium (Ca0.4Sr0.6S:Eu(2+), CSSE) on a backlight conversion foil in photosynthesis experiments. We show that this phosphor can be used to effectively convert green to red light, centering at a wavelength of ~650 nm which overlaps the absorption peaks of chlorophyll a/b pigments. A measurement system was developed to monitor the photosynthetic activity, expressed as the CO2 assimilation rate of spinach leaves under various controlled light conditions. Results show that under identical external light supply which is rich in green photons, the CO2 assimilation rate can be enhanced by more than 25% when the actinic light is modified by the CSSE conversion foil as compared to a purely reflecting reference foil. These results show that the phosphor could be potentially applied to modify the solar spectrum by converting the green photons into photosynthetically active red photons for improved photosynthetic activity.

Rare-earth ion doped up-conversion materials for photovoltaic applications.

With the aim of utilizing the infrared region of solar radiation to improve solar cell performance, significant progress, including theoretical analysis and experimental achievement, has been made in the field of up-conversion for photovoltaic applications. This Research News article reviews recent progress in the development of rear-earth (RE) ion doped up-conversion materials for solar cell applications. In addition, new trends for RE-ion-doped phosphors are briefly discussed, among them trivalent RE-ion-doped up-conversion materials for organic solar cell applications.

Luminescent silicate core-shell nanoparticles: synthesis, functionalization, optical, and structural properties.

SiO(2)/Zn(2)SiO(4):Mn(2+) core-shell nanoparticles with mean diameters in the range of 55-220 nm were prepared by a modified Pechini sol-gel method followed by lyophilization and annealing at temperatures of 800-1100°C. The as-synthesized nanoparticles were characterized by transmission electron microscopy, X-ray diffraction analysis, and photoluminescence spectroscopy. The results demonstrate that the crystal structure of the shell and the optical properties can be tuned by the annealing temperature and a variation of the concentration of doping ions. Under UV excitation, the samples emit green luminescence with its maximum at 525 nm, typical for the Mn(2+) ions in α-Zn(2)SiO(4). The resulting nanoparticles were successfully modified with amine and carboxyl functions with respect to a later attachment of biological moieties.

Synthesis and spectroscopic investigations of Cu- and Pb-doped colloidal ZnS nanocrystals.

A novel organometallic synthesis method for the preparation of colloidal ZnS nanoparticles is presented. This method enables the synthesis of undoped ZnS nanocrystals as well as doping with Cu, Pb, or both. The particles can be covered with an undoped layer of ZnS, forming core/shell-type particles with the ZnS:Pb, ZnS:Cu, or ZnS:Cu,Pb cores. The particles were characterized via TEM, XRD, dynamic light scattering, and optical spectroscopy. We investigated the extrinsic surface defects and their coverage with an additional ZnS layer in detail by temperature-dependent luminescence and luminescence lifetime spectroscopy.