RESUMO
The study of bio-inspired structures and their reproduction has always fascinated humans. The advent of soft robotics, thanks to soft materials, has enabled considerable progress in this field. Over the years, polyps, worms, cockroaches, jellyfish, and multiple anthropomorphic structures such as hands or limbs have been reproduced. These structures have often been used for gripping and handling delicate objects or those with complex unknown a priori shapes. Several studies have also been conducted on grippers inspired by the seahorse tail. In this paper, a novel biomimetic soft pneumatic actuator inspired by the tail of the seahorse Hippocampus reidi is presented. The actuator has been developed to make a leg to sustain a multi-legged robot. The prototyping of the actuator was possible by combining a 3D-printed reinforcement in thermoplastic polyurethane, mimicking the skeletal apparatus, within a silicone rubber structure, replicating the functions of the external epithelial tissue. The latter has an internal channel for pneumatic actuation that acts as the inner muscle. The study on the anatomy and kinematic behaviour of the seahorse tail suggested the mechanical design of the actuator. Through a test campaign, the actuator prototype was characterized by isotonic tests with an external null load, isometric tests, and activation/deactivation times. Specifically, the full actuator distension of 154.5 mm occurs at 1.8 bar, exerting a maximum force of 11.9 N, with an activation and deactivation time of 74.9 and 94.5 ms, respectively.
RESUMO
This paper illustrates an experimental activity for the closed-loop position control of an actuator made using shape memory alloy (SMA) wire. A solution with the self-sensing effect was implemented to miniaturize the systems, i.e., without external sensors. A proportional control algorithm was initially used, demonstrating the idea's feasibility; the wire can behave simultaneously as an actuator and sensor. An experimental investigation was subsequently conducted for the optimization of the developed actuator. As for the material, a Flexinol wire, Ni-Ti alloy, with a diameter of 0.150 mm and a length of 200 mm, was used. Preliminarily, characterization of the SMA wire at constant and variable loads was carried out; the characteristics detected were elongation vs. electric current and elongation vs. electrical resistance. The control system is PC based with a data acquisition card (DAQ). A drive board was designed and built to read the wire's electrical resistance and power it by pulse width modulation (PWM). A notable result is that the actuator works with good precision and in dynamic conditions, even when it is called to support a load up to 65% different from that for which the electrical resistance-length correlation has previously been experimentally obtained, on which the control is based. This opens up the possibility of using the actuator in a counteracting configuration with a spring, which makes hardware implementation and control management simple.
RESUMO
This paper reports on the design, implementation, and characterization of a current-mode analog-front-end circuit for capacitance-to-voltage conversion that can be used in connection with a large variety of sensors and actuators in industrial and rehabilitation medicine applications. The circuit is composed by: (i) an oscillator generating a square wave signal whose frequency and pulse width is a function of the value of input capacitance; (ii) a passive low-pass filter that extracts the DC average component of the square wave signal; (iii) a DC-DC amplifier with variable gain ranging from 1 to 1000. The circuit has been designed in the current-mode approach by employing the second-generation current conveyor circuit, and has been implemented by using commercial discrete components as the basic blocks. The circuit allows for gain and sensitivity tunability, offset compensation and regulation, and the capability to manage various ranges of variations of the input capacitance. For a circuit gain of 1000, the measured circuit sensitivity is equal to 167.34 mV/pF with a resolution in terms of capacitance of 5 fF. The implemented circuit has been employed to measure the variations of the capacitance of a McKibben pneumatic muscle associated with the variations of its length that linearly depend on the circuit output voltage. Under step-to-step conditions of movement of the pneumatic muscle, the overall system sensitivity is equal to 70 mV/mm with a standard deviation error of the muscle length variation of 0.008 mm.
RESUMO
In this paper, the design of a 2-dof (degrees of freedom) rehabilitation robot for upper limbs driven by pneumatic muscle actuators is presented. This paper includes the different aspects of the mechanical design and the control system and the results of the first experimental tests. The robot prototype is constructed and at this preliminary step a position and trajectory control by fuzzy logic is implemented. The pneumatic muscle actuators used in this arm are designed and constructed by the authors' research group.
RESUMO
This paper describes the results of research projects developed at the University of L'Aquila by the research group of the authors in the field of biomedical engineering, which have seen an important use of additive manufacturing technologies in the prototyping step and, in some cases, also for the realization of preindustrialization prototypes. For these projects, commercial 3D printers and technologies such as fused deposition modelling (FDM) were used; the most commonly used polymers in these technologies are acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA). The research projects concern the development of innovative actuators, such as pneumatic muscles and soft pneumatic actuators (SPAs), the development of active orthoses, such as a lower limb orthosis and, finally, the development of a variable-stiffness grasper to be used in natural orifice transluminal endoscopic surgery (NOTES). The main aspects of these research projects are described in the paper, highlighting the technologies used such as the finite element analysis and additive manufacturing.
Assuntos
Engenharia Biomédica/métodos , Aparelhos Ortopédicos , Desenho de Prótese/métodos , Análise de Elementos Finitos , Humanos , Maleabilidade , Polímeros/químicaRESUMO
The emerging demographic trends toward an aging population, demand new ways and solutions to improve the quality of elderly life. These include, prolonged independent living, improved health care, and reduced social isolation. Recent technological advances in the field of assistive robotics bring higher sophistication and various assistive abilities that can help in achieving these goals. In this paper, we present design and validation of a low-cost telepresence robot that can assist the elderly and their professional caregivers, in everyday activities. The developed robot structure and its control objectives were tested in, both, a simulation and experimental environment. On-field experiments were done in a private elderly care center involving elderly persons and caregivers as participants. The goal of the evaluation study was to test the software architecture and the robot capabilities for navigation, as well as the robot manipulator. Moreover, participants' reactions toward a possible adoption of the developed robot system in everyday activities were assessed. The obtained results of the conducted evaluation study are also presented and discussed.
Assuntos
Monitorização Fisiológica/instrumentação , Robótica/tendências , Telemedicina/tendências , Atividades Cotidianas , Idoso , Moradias Assistidas , Serviços de Assistência Domiciliar , Humanos , Vida Independente , Qualidade de Vida , Tecnologia Assistiva , Interface Usuário-ComputadorRESUMO
PURPOSE: For off-road mobility, some manual or power assisted devices were conceived to be self-driven by paraplegics while for tetraplegics non power-assisted devices were conceived. These devices require one or more conductors who are subjected to a high physical demand thus potentially creating: precarious safety condition for the user an elevated physical demand of conductors could reduce the care and the attention to give to the user; the time of the outdoor adventure experience of the user could be limited. METHODS: To address these issues, an innovative user-centered power assisted off-road wheelchair for the transportation of tetraplegics along mountain trails was developed. The device, structured like a trike, is driven by two healthy conductors; the user is placed in the middle of the frame. A movable seat provides for the transfer from the standard to the off-road wheelchair. An electrical motor, powered by a battery pack, provides for the actuation. All the design and prototype aspects, the control system and experimental tests are detailed. RESULTS: The prototype satisfies mechanical, safety and duration requirements. No physical demand while using the device and for the transfer of the user to the device was identified. Fun and engaging tests were carried out and all the participants were involved. Implications for Rehabilitation The device has the potential to enhance the quality of life of tetraplegics in terms of new life experiences. The device revealed the real possibility of a full recreational experience, an enhanced participation and a better social integration of tetraplegics.
Assuntos
Pessoas com Deficiência , Atividades de Lazer , Paraplegia/fisiopatologia , Cadeiras de Rodas , Fontes de Energia Elétrica , Desenho de Equipamento , HumanosRESUMO
BACKGROUND: In natural orifice transluminal endoscopic surgery (NOTES) the peritoneal cavity is reached through natural orifices (mouth, rectus and transvaginal duct), by means of little cuttings in the walls of hollow organs. Due to narrow spaces, NOTES needs robotic systems to assure operation/movement precision and patient safety. Variable stiffness actuation (VSA) assures both requirements. METHODS: The authors developed a grasper for NOTES, provided with VSA, to use as an end-effector for snail robot devices. The present paper deals with basic concepts of VSA and describes the design and architecture of the grasper. Characterization and functional experiments were performed and results analysed. RESULTS: A finite element model developed for the actuator design was validated, performance grasper characteristic curves were obtained, VSA was validated, and the gripping capability of several objects was assessed. CONCLUSION: The grasper satisfies technical design specifications. On the basis of the results obtained, a control system can be developed to test grasper in a simulated surgery environment.
Assuntos
Cirurgia Endoscópica por Orifício Natural/instrumentação , Procedimentos Cirúrgicos Robóticos/instrumentação , Fenômenos Biomecânicos , Desenho de Equipamento , Análise de Elementos Finitos , Humanos , Modelos Anatômicos , Cirurgia Endoscópica por Orifício Natural/estatística & dados numéricos , Cavidade Peritoneal/cirurgia , Procedimentos Cirúrgicos Robóticos/estatística & dados numéricosRESUMO
The telepresence robot is a type of technology used to socialize with people in remote places. If this technology is efficient, it could be an alternative means to attend social activities such as going to school and work for people who have difficulty to go out because of motor impairments. The objective of this study is to investigate the effect of using a telepresence robot in the marketplace by individuals with motor impairments. Three participants were involved with trial use for attending university courses for a month and the initial results are shown.