Electric Susceptibility at Partial Coverage of a Circular One-Side Access Capacitive Sensor with Rigid Polyurethane Foams.

The capability of dielectric measurements was significantly increased with the development of capacitive one-side access physical sensors. Complete samples give no opportunity to study electric susceptibility at a partial coverage of the one-side access sensor's active area; therefore, partial samples are proposed. The electric susceptibility at the partial coverage of a circular one-side access sensor with cylinders and shells is investigated for polyurethane materials. The implementation of the relative partial susceptibility permitted us to transform the calculated susceptibility data to a common scale of 0.0-1.0 and to outline the main trends for PU materials. The partial susceptibility, relative partial susceptibility, and change rate of relative partial susceptibility exhibited dependence on the coverage coefficient of the sensor's active area. The overall character of the curves for the change rate of the relative partial susceptibility, characterised by slopes of lines and the ratio of the change rate in the centre and near the gap, corresponds with the character of the surface charge density distribution curves, calculated from mathematical models. The elaborated methods may be useful in the design and optimization of capacitive OSA sensors of other configurations of electrodes, independent of the particular technical solution.

Characteristics of Components and Density of Rigid Nanoclay-Filled Medium-Density Polyurethane Foams Produced in a Sealed Mould.

The characteristics of rigid, nanoclay-filled, medium-density NEOpolyol-380 polyurethane foams components can be estimated when two conditions are met: (1) the foam blocks are produced in a sealed mould; and (2) the mass of the reacting mixture is kept constant. It was shown that, with an increase in filler concentration, the total mass of the filled polymeric network stays constant, but the total volume reduces; the higher the ratio of density of the exfoliated nanoclay platelets and polymer, the higher the volume reduction of the polymeric network. Experimental data of polyurethane foam block mass were acquired at concentrations η = 0%, 0.25%, 0.5%, 1%, 2%, 3% and 5% from the mass of a filled reacting mixture. Foam-density dependence in the uniform zone and in the side-sections of the produced blocks on the: (1) mass of the blocks; and (2) the concentration of the filler was analysed. The study demonstrated that the correlation of the specimens' density with the foam block mass is much higher than that of the filler concentration.

Anisotropy and Mechanical Properties of Nanoclay Filled, Medium-Density Rigid Polyurethane Foams Produced in a Sealed Mold, from Renewable Resources.

Medium-density rigid polyurethane (PU) foams are often produced in sealed molds; therefore, the processes inside the mold and structure of the produced foam blocks need to be understood. The structural and mechanical anisotropy is shown to be the third variable along with (1) concentration of the nanoclay filler and (2) density, to determine the mechanical properties of the filled PU foam composites produced in a sealed mold. The varying anisotropy of the specimens hinders the accurate evaluation of the filling effect. The methodology for the estimation of the anisotropy characteristics of specimens from different locations within the nanoclay filled PU foam blocks is elaborated. A criterion, based on analysis of Poisson's ratios, is formulated for the selection of specimens with similar anisotropy characteristics. The shear and bulk moduli are estimated theoretically, dependent on the filler's concentration, using the experimentally determined constants.

The Impact of Atmospheric Parameters on the Dielectric Permittivity Values of SikaBlock®-M150 and Other Rigid Polyurethane Foams Measured with a Capacitive One-Side Access Sensor.

A shortage of research on the impact of atmospheric parameters on the measured dielectric permittivity values of rigid polyurethane (PU) foams was identified. Therefore, the impact of temperature, pressure, and relative humidity of air in the test room on the measured values of dielectric permittivity of rigid PU foams of different densities as well as monolithic polyurethane was investigated in a year-long experimental research study with a capacitive one-side access sensor. It was shown that relative humidity has the highest correlation with the dielectric permittivity values of rigid PU materials. The detected values of parameters were linked to the water vapour mass in ambient air and its correlation with permittivity of the investigated materials was determined. The warm-up drift and warm-up time of the spectrometer were estimated experimentally. A novel methodology was demonstrated to determine the true permittivity spectrum of rigid PU foams without any involvement of the environmental chamber, desiccators, or saturated salt/water solutions. A relative increase in the measured dielectric permittivity value was estimated numerically for the entire density range of rigid PU foams, i.e., 33-1280 kg/m3 (including monolithic PU).

Light Microscopy of Medium-Density Rigid Polyurethane Foams Filled with Nanoclay.

Practical applications and mathematical modelling of the physical and mechanical properties of medium-density rigid polyurethane foams require knowledge of their structure. It is necessary to determine structural characteristics without destroying the foams and measuring each element. A methodology is described for the use of light microscopy on environmentally sustainable, medium-density rigid polyurethane foams (in the density region of ≈210-230 kg/m3), by the analysis of two types of light microscopy images: (1) Cutting surface images; and (2) Through-cutting surface images. The dimensions of structural elements of polyurethane foams, filled with the nanoclay Cloisite-30B at concentrations of 0.0%, 0.25%, 0.50%, 1.0%, 2.0%, 3.0%, and 5.0% from the mass of the filled reacting mixture, are estimated. Probability density functions of projections of bubbles' diameters and struts' length are determined using images in three mutually perpendicular planes. A mathematical model is developed for the restoration of the actual dimensions of bubbles' diameters using data of cutting circles' diameters. Intercalation and exfoliation of the filler's Cloisite-30B mono-layers is evaluated via the basal spacing by X-ray diffraction at a 5 wt.% concentration of nanoclay.

Modeling the Nonlinear Deformation of Highly Porous Cellular Plastics Filled with Clay Nanoplatelets.

Rigid low-density plastic foams subjected to mechanical loads typically exhibit a nonlinear deformation stage preceding failure. At moderate strains, when the geometrical nonlinearity is negligible, such foam response is predominantly caused by the nonlinearity of deformation of their principal structural elements-foam struts. Orientational averaging of stresses in foam struts enables estimation of the stresses taken up by foams at a given applied strain. Based on a structural model of highly porous anisotropic cellular plastics filled with clay nanoplatelets and the orientational averaging, a method for calculating their nonlinear deformation is derived in terms of structural parameters of the porous material, the mechanical properties of the monolithic polymer, and filler particles and their spatial orientation. The method is applied to predicting the tensile stress-strain diagrams of organoclay-filled low-density rigid polyurethane foams, and reasonable agreement with experimental data is demonstrated.

Polytetrafluoroethylene Films in Rigid Polyurethane Foams' Dielectric Permittivity Measurements with a One-Side Access Capacitive Sensor.

As a non-metallic composite material, widely applied in industry, rigid polyurethane (PUR) foams require knowledge of their dielectric properties. In experimental determination of PUR foams' dielectric properties protection of one-side capacitive sensor's active area from adverse effects caused by the PUR foams' test objects has to be ensured. In the given study, the impact of polytetrafluoroethylene (PTFE) films, thickness 0.20 mm and 0.04 mm, in covering or simulated coating the active area of one-side access capacitive sensor' electrodes on the experimentally determined true dielectric permittivity spectra of rigid PUR foams is estimated. Penetration depth of the low frequency excitation field into PTFE and PUR foams is determined experimentally. Experiments are made in order to evaluate the difference between measurements on single PUR foams' samples and on complex samples "PUR foams + PTFE film" with two calibration modes. A modification factor and a small modification criterion are defined and values of modifications are estimated in numerical calculations. Conclusions about possible practical applications of PTFE films in dielectric permittivity measurements of rigid PUR foams with one-side access capacitive sensor are made.