FGF4L2 retrogene copy number is associated with intervertebral disc calcification and vertebral geometry in Nova Scotia Duck Tolling Retrievers.

OBJECTIVES: To evaluate the effects of the chondrodystrophy-associated FGF4L2 retrogene on intervertebral disc (IVD) calcification and vertebral geometry. ANIMALS: 22 Nova Scotia Duck Tolling Retrievers (NSDTR) with no FGF4L2 retrogene (n = 7, wild-type dogs), 1 retrogene copy (8, heterozygous dogs), or 2 retrogene copies (7, homozygous dogs). PROCEDURES: Computed tomography (CT) scans of the vertebral column were analyzed using computer-aided design (CAD) software. IVD calcification, vertebral column length, and vertebral geometry of the third cervical (C3), 13th thoracic (T13), and first lumbar (L1) vertebrae were compared. RESULTS: IVD calcification was not found in wild-type dogs. IVD calcification was more frequent in homozygous dogs than heterozygous (P = .008) or wild-type dogs (P < .001) and in heterozygous dogs compared to wild-type dogs (P < .001). Four IVDs were subclinically herniated in 3 dogs (2 homozygous, 1 heterozygous). Calcified IVD had a greater volume and surface area in heterozygous dogs than homozygous dogs. C3 vertebral canal height-to-width ratio was greater in homozygous dogs than heterozygous dogs (P = .044) and wild-type dogs (P = .010). CLINICAL RELEVANCE: IVD calcification and vertebral geometry can be analyzed using CAD software. The presence of 1 or 2 FGF4L2 copies in the absence of the FGF4L1 retrogene has an additive effect on the number of calcified IVD and a minor effect on vertebral geometry in NSDTR dogs. Data support the use of FGF4L2 phenotyping to reduce clinical disease in segregating breeds and to monitor the introduction of wild-type alleles into fixed breed populations.

CuI p-type thin films for highly transparent thermoelectric p-n modules.

Developments in thermoelectric (TE) transparent p-type materials are scarce and do not follow the trend of the corresponding n-type materials - a limitation of the current transparent thermoelectric devices. P-type thermoelectric thin films of CuI have been developed by three different methods in order to maximise optical transparency (>70% in the visible range), electrical (σ = 1.1 × 104 Sm-1) and thermoelectric properties (ZT = 0.22 at 300 K). These have been applied in the first planar fully transparent p-n type TE modules where gallium-doped zinc oxide (GZO) thin films were used as the n-type element and indium thin oxide (ITO) thin films as electrodes. A thorough study of power output in single elements and p-n modules electrically connected in series and thermally connected in parallel is inclosed. This configuration allows for a whole range of highly transparent thermoelectric applications.

Optimization of Cuprous Oxides Thin Films to be used as Thermoelectric Touch Detectors.

The electronic and optical properties of p-type copper oxides (CO) strongly depend on the production technique as it influences the obtained phases: cuprous oxide (Cu2O) or cupric oxide (CuO), the most common ones. Cu films deposited by thermal evaporation have been annealed in air atmosphere, with temperature between 225 and 375 °C and time between 1 and 4 h. The resultant CO films have been studied to understand the influence of processing parameters in the thermoelectric, electrical, optical, morphological, and structural properties. Films with a Cu2O single phase are formed when annealing at 225 °C, while CuO single phase films can be obtained at 375 °C. In between, both phases are obtained in proportions that depend on the film thickness and annealing time. The positive sign of the Seebeck coefficient (S), measured at room temperature (RT), confirms the p-type behavior of both oxides, showing values up to 1.2 mV·°C-1 and conductivity up to 2.9 (Ω·m)-1. A simple detector using Cu2O have been fabricated and tested with fast finger touch events.