Thiol-Ene Click Cross-linking of Starch Oleate Films for Enhanced Properties.

Biobased films were synthesized from starch oleate (DS = 2.2) cross-linked with polyethylene glycol with Mn = 2000 and 1000 g · mol-1, and ethylene glycol, all of which were esterified with either lipoic acid (LA) or 3-mercaptopropionic acid (MPA). Cross-linking was achieved through a UV-initiated thiol-ene click, and confirmed by Fourier transform infrared spectroscopy and rheometry. The films exhibit higher degradation temperatures, and an increased degree of crystallinity as cross-linker length increased. The introduction of MPA-based cross-linkers resulted in hydrophilic films, while the contact angle was barely affected by the addition of LA-based cross-linkers. A reduction in maximum strength upon introducing the cross-linkers was observed, while an increase in elongation was observed for most of the LA-based cross-linkers. Our results demonstrate the potential for tuning the mechanical and thermal properties of starch-based films through the cross-linker choice, with some formulations exhibiting increased flexibility that may be well suited for packaging applications.

Lipoic acid-based vitrimer-like elastomer.

Dynamic covalent networks (DCNs) are materials that feature reversible bond formation and breaking, allowing for self-healing and recyclability. To speed up the bond exchange, significant amounts of catalyst are used, which creates safety concerns. To tackle this issue, we report the synthesis of a lipoic acid-based vitrimer-like elastomer (LAVE) by combining (i) ring-opening polymerization (ROP) of lactones, (ii) lipoic acid modification of polylactones, and (iii) UV crosslinking. The melting temperature (Tm) of LAVE is below room temperature, which ensures the elastic properties of LAVE at service temperature. By carefully altering the network, it is possible to tune the Tm, as well as the mechanical strength and stretchability of the material. An increase in polylactone chain length in LAVE was found to increase strain at break from 25% to 180% and stress at break from 0.34 to 1.41 MPa. The material showed excellent network stability under cyclic strain loading, with no apparent hysteresis. The introduction of disulfide bonds allows the material to self-heal under UV exposure, extending its shelf life. Overall, this work presents an environmentally friendly approach for producing a sustainable elastomer that has potential for use in applications such as intelligent robots, smart wearable technology, and human-machine interfaces.

Starch ester film properties: The role of the casting temperature and starch its molecular weight and amylose content.

Oleic acid and 10-undecenoic acid were used to esterify corn, tapioca, potato and a waxy potato starch, with a maximum degree of substitution of 2.4 and 1.9 respectively. The thermal and mechanical properties were investigated as a function of the amylopectin content and Mw of starch, and by the fatty acid type. All starch esters had an improved degradation temperature regardless of their botanical origin. While the Tg did increase with increasing amylopectin content and Mw, it decreased with increasing fatty acid chain length. Moreover, films with different optical appearances were obtained by varying the casting temperature. SEM and polarized light microscopy showed that films cast at 20 °C had porous open structures with internal stress, which was absent when cast at higher temperatures. Tensile test measurements revealed that films had a higher Young's modulus when containing starch with a higher Mw and amylopectin content. Besides that, starch oleate films were more ductile than starch 10-undecenoate films. In addition, all films were resistant to water at least up to one month, while some light-induced crosslinking took place. Finally, starch oleate films showed antibacterial properties against Escherichia coli, whereas native starch and starch 10-undecenoate did not.

Synthesis and Properties of Fully Biobased Crosslinked Starch Oleate Films.

Starch oleate (degree of substitution = 2.2) films were cast and crosslinked in the presence of air using UV curing (UVC) or heat curing (HC). A commercial photoinitiator (CPI, Irgacure 184) and a natural photoinitiator (NPI, a mixture of biobased 3-hydroxyflavone and n-phenylglycine) were used for UVC. No initiator was used during HC. Isothermal gravimetric analyses, Fourier Transform Infrared (FTIR) measurements, and gel content measurements revealed that all three methods were effective in crosslinking, with HC being the most efficient. All methods increased the maximum strengths of film, with HC causing the largest increase (from 4.14 to 7.37 MPa). This is consistent with a higher degree of crosslinking occurring with HC. DSC analyses showed that the Tg signal flattened as film crosslink densities increased, even disappearing in the case of HC and UVC with CPI. Thermal gravimetric analyses (TGA) indicated that films cured with NPI were least affected by degradation during curing. These results suggest that cured starch oleate films could be suitable for replacing the fossil-fuel-derived plastics currently used in mulch films or packaging applications.

Scalable and Degradable Dextrin-Based Elastomers for Wearable Touch Sensing.

Elastomer-based wearables can improve people's lives; however, frictional wear caused by manipulation may pose significant concerns regarding their durability and sustainability. To address the aforementioned issue, a new class of advanced scalable supersoft elastic transparent material (ASSETm) is reported, which offers a unique combination of scalability (20 g scale), stretchability (up to 235%), and enzymatic degradability (up to 65% in 30 days). The key feature of our design is to render native dextrin hydrophobic, which turns it into a macroinitiator for bulk ring-opening polymerization. Based on ASSETm, a self-powered touch sensor (ASSETm-TS) for touch sensing and non-contact approaching detection, possessing excellent electrical potential (up to 65 V) and rapid response time (60 ms), is fabricated. This work is a step toward developing sustainable soft electronic systems, and ASSETm's tunability enables further improvement of electrical outputs, enhancing human-interactive applications.

A more efficient synthesis and properties of saturated and unsaturated starch esters.

This work presents a series of starch esters synthesized via 1,5,7-triazabicyclo[4.4.0]-dec-5-ene (TBD) catalyzed transesterifications in dimethyl sulfoxide (DMSO). The reaction was performed with saturated and unsaturated fatty acids (8, 11, and 18 carbon atoms). The degree of substitution (DS) was raised by purging the reaction flask with nitrogen instead of simply performing the reaction under a nitrogen atmosphere. The increase of DS was most obvious for long-chain fatty acids, as an almost complete DS was observed for starch stearate (2.8) and starch oleate (2.7). The products were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and X-ray diffraction. Starch esters from unsaturated fatty acids have a lower Tg than their saturated analogues. Moreover, contact angle and moisture uptake measurements showed increased hydrophobicity for all starch esters in comparison to pristine starch. Our results show a more efficient method for synthesizing a biobased material that steers into the direction of a material that could replace conventional plastics.

Supramolecular Mimic for Bottlebrush Polymers in Bulk.

A series of poly(tetrahydrofuran)s with molecular weights above entanglement molecular weight M e were synthesized, and one of their end-groups was functionalized with a supramolecular entity so that the corresponding polymers form a brushlike structure suitable for comparison with conventional irreversible bottlebrush polymers. To compare their relaxation mechanisms, linear rheology was employed and showed that a hierarchical relaxation, which is usually observed in bottlebrush polymers, occurs in these materials, too. The polymer chain segments close to the supramolecular backbone are highly immobilized due to strong association in the center of polymer brush and cannot relax via reptation mechanism, which is mainly responsible for linear entangled polymer relaxations. Therefore, disentanglement can take much longer through contour length fluctuations and arm retraction processes similar to covalent bottlebrush polymers and combs. The relaxed ends of polymers then act as solvent to let the remaining segments of the polymeric brush undergo Rouse-like motions (constraint release Rouse). At longer times, additional plateau appears, which can be attributed to the relaxation of the entire supramolecular bottlebrush polymer via hopping or reptative motions. With an increase of temperature, viscoelastic solid behavior turns into viscoelastic liquid due to reversible depolymerization of the supramolecular backbone of the bottlebrush polymer. The elastic modulus (G' in the order of kPa) was much less than the values found for the entanglement plateau modulus of linear poly(tetrahydrofuran) (in order of MPa). This low modulus value, which exists up to very low frequencies (high temperatures), makes them a good candidate for supersoft elastomers.