Laser-Induced Pd-PdO/rGO Catalysts for Enhanced Electrocatalytic Conversion of Nitrate into Ammonia.

Electrochemical reduction of nitrate to ammonia (eNO3RR) is proposed as a sustainable solution for high-rate ammonia synthesis under ambient conditions. The complex, multistep eNO3RR mechanism necessitates the use of a catalyst for the complete conversion of nitrate to ammonia. Our research focuses on developing a novel Pd-PdO doped in a reduced graphene oxide (rGO) composite catalyst synthesized via a laser-assisted one-step technique. This catalyst demonstrates dual functionality: palladium (Pd) boosts hydrogen adsorption, while its oxide (PdO) demonstrates considerable nitrogen adsorption affinity and exhibits a maximum ammonia yield of 5456.4 ± 453.4 µg/h/cm2 at -0.6 V vs reversible hydrogen electrode (RHE), with significant yields for nitrite and hydroxylamine under ambient conditions in a nitrate-containing alkaline electrolyte. At a lower potential of -0.1 V, the catalyst exhibited a minimal hydrogen evolution reaction of 3.1 ± 2.2% while achieving high ammonia selectivity (74.9 ± 4.4%), with the balance for nitrite and hydroxylamine. Additionally, the catalyst's stability and activity can be regenerated through the electrooxidation of Pd.

Graphene's Role in Emerging Trends of Capacitive Energy Storage.

Technological breakthroughs in energy storage are being driven by the development of next-generation supercapacitors with favorable features besides high-power density and cycling stability. In this innovation, graphene and its derived materials play an active role. Here, the research status of graphene supercapacitors is analyzed. Recent progress is outlined in graphene assembly, exfoliation, and processing techniques. In addition, electrochemical and electrical attributes that are increasingly valued in next-generation supercapacitors are highlighted along with a summary of the latest research addressing chemical modification of graphene and its derivatives for future supercapacitors. The challenges and solutions discussed in the review hopefully will shed light on the commercialization of graphene and a broader genre of 2D materials in energy storage applications.

The effectiveness of Soxhlet extraction as a simple method for GO rinsing as a precursor of high-quality graphene.

Graphite-oxide (GO) is a valuable compound produced by the chemical oxidation of graphite. The procedure for converting graphite into GO includes two steps: oxidation and subsequent rinsing. Proper rinsing is essential to obtain processable and applicable graphite-oxide. Traditionally, the rinsing involves filtration or centrifugation; both processes are extremely time-consuming, expensive, unsafe, and produce environmentally hazardous liquid waste in large volume. This study reveals an alternative method to rinse graphite-oxide using a Soxhlet extractor. Since only the vapor of the solvent is used for washing, Soxhlet rinsing offers reuse of the same solvent for many automatic subsequent cycles, leading to considerable solvent savings, reducing pollutants and work time, and ensuring safer production. The quality of the produced GO is evaluated by Raman spectroscopy, X-Ray diffraction (XRD), inductively coupled plasma (ICP), elemental analysis, and electron microscopy. Moreover, we test the electrochemical performances of reduced GO (rGO), the main final product of graphite-oxide. Finally, we discuss the benefits involved in the suggested rinsing method and compare its profitability with traditional methods. Soxhlet rinsing is favored environmentally and economically. Particularly, the automatic operation of many washing sequences saves labor time, and the reuse of the washing solvent spares a large volume of chemically deleterious solvents.

Surface modifications of carbon nanodots reveal the chemical source of their bright fluorescence.

Fluorescent carbon nanodots (CNDs) have drawn increasing attention in recent years. These cost-effective and eco-friendly nanomaterials with bright fluorescence have been investigated as promising materials for electrooptic and bioimaging applications. However, the chemical source stimulating their strong fluorescence has not been completely identified to date. Depending on the chemical composition, two absorption peaks are observed in the visible range. In this study, we applied selected chemical modifications to CNDs in order to elucidate the correlation between the chemical structure and optical behavior of CNDs. Varying the amount of acetic acid in the synthesis process resulted in different effects on the absorbance and fluorescence photo-spectra. Specifically, at a low concentration (10%), the fluorescence is dramatically red shifted from 340 to 405 nm. Comprehensive characterization of the chemical modification by FTIR and XPS allows identification of the role of acetic acid in the reaction mechanism leading to the modified photoactivity. The functional group responsible for the 405 nm peak was identified as HPPT. We describe a chemical mechanism involving acetic acid that leads to an increased concentration of HPPT groups on the surface of the CNDs. Applying two additional independent chemical and consequently optical modifications namely solution pH and annealing on the nanodots further supports our proposed explanation. Understanding the molecular origin of CND fluorescence may promote the design and control of effective CND fluorescence in optical applications.

In†Operando Calorimetric Measurements for Activated Carbon Electrodes in Ionic Liquid Electrolytes under Large Potential Windows.

This study aims to investigate the effect of the potential window on heat generation in carbon-based electrical double layer capacitors (EDLCs) with ionic-liquid (IL)-based electrolytes using in operando calorimetry. The EDLCs consisted of two identical activated-carbon electrodes with either neat 1-butyl-1-methylpyrrolidinium bis(trifluoromethane-sulfonyl)imide ([Pyr14 ][TFSI]) electrolyte or 1.0 m [Pyr14 ][TFSI] in propylene carbonate (PC) as electrolyte. The instantaneous heat generation rate at each electrode was measured under galvanostatic cycling for different potential windows ranging from 1 to 4 V. First, the heat generation rates at the positive and negative electrodes differed significantly in neat IL owing to the differences in the ion sizes and diffusion coefficients. However, these differences were minimized when the IL was diluted in PC. Second, for EDLC in neat [Pyr14 ][TFSI] at high potential window (4 V), a pronounced endothermic peak was observed at the beginning of the charging step at the positive electrode owing to TFSI- intercalation in the activated carbon. On the other hand, for EDLC in 1.0 m [Pyr14 ][TFSI] in PC at potential window above 3 V, an endothermic peak was observed only at the negative electrode owing to the decomposition of PC. Third, for both neat and diluted [Pyr14 ][TFSI] electrolytes, the irreversible heat generation rate increased with increasing potential window and exceeded Joule heating. This was attributed to the effect of potential-dependent charge redistribution resistance. A further increase in the irreversible heat generation rate was observed for the largest potential windows owing to the degradation of the PC solvent. Finally, for both types of electrolyte, the reversible heat generation rate increased with increasing potential window because of the increase in the amount of ion adsorbed/desorbed at the electrode/electrolyte interface.

Laser-Assisted Lattice Recovery of Graphene by Carbon Nanodot Incorporation.

Producing highly oriented graphene is a major challenge that constrains graphene from fulfilling its full potential in technological applications. The exciting properties of graphene are impeded in practical bulk materials due to lattice imperfections that hinder charge mobility. A simple method to improve the structural integrity of graphene by utilizing laser irradiation on a composite of carbon nanodots (CNDs) and 3D graphene is presented. The CNDs attach themselves to defect sites in the graphene sheets and, upon laser-assisted reduction, patch defects in the carbon lattice. Spectroscopic experiments reveal graphitic structural recovery of up to 43% and electrical conductivity four times larger than the original graphene. The composites are tested as electrodes in electrochemical capacitors and demonstrate extremely fast RC time constant as low as 0.57 ms. Due to their low defect concentrations, the reduced graphene oxide-carbon nanodot (rGO-CND) composites frequency response is sufficiently fast to operate as AC line filters, potentially replacing today's electrolytic capacitors. Using this methodology, demonstrated is a novel line filter with one of the fastest capacitive responses ever reported, and an aerial capacitance of 68.8 mF cm-2 . This result emphasizes the decisive role of structural integrity for optimizing graphene in electronic applications.

Patching laser-reduced graphene oxide with carbon nanodots.

Three-dimensional graphenes are versatile materials for a range of electronic applications and considered among the most promising candidates for electrodes in future electric double layer capacitors (EDLCs) as they are expected to outperform commercially used activated carbon. Parameters such as electrical conductivity and active surface area are critical to the final device performance. By adding carbon nanodots to graphene oxide in the starting material for our standard laser-assisted reduction process, the structural integrity (i.e. lower defect density) of the final 3D-graphene is improved. As a result, the active surface area in the hybrid starting materials was increased by 130% and the electrical conductivity enhanced by nearly an order of magnitude compared to pure laser-reduced graphene oxide. These improved material parameters lead to enhanced device performance of the EDLC electrodes. The frequency response, i.e. the minimum phase angle and the relaxation time, were significantly improved from -82.2° and 128 ms to -84.3° and 7.6 ms, respectively. For the same devices the specific gravimetric device capacitance was increased from 110 to a maximum value of 214 F g-1 at a scan rate of 10 mV s-1.

Carbon Nanodots as Feedstock for a Uniform Hematite-Graphene Nanocomposite.

High degrees of dispersion are a prerequisite for functional composite materials for applications in electronics such as sensors, charge and data storage, and catalysis. The use of small precursor materials can be a decisive factor in achieving a high degree of dispersion. In this study, carbon nanodots are used to fabricate a homogeneous, finely dispersed Fe2 O3 -graphene composite aerogel in a one-step conversion process from a precursor mixture. The laser-assisted conversion of small size carbon nanodots enables a uniform distribution of 6.5 nm Fe2 O3 nanoparticles during the formation of a highly conductive carbon matrix. Structural and electrochemical characterization shows that the features of both material entities are maintained and successfully integrated. The presence of Fe2 O3 nanoparticles has a positive effect on the active surface area of the carbon aerogel and thus on the capacitance of the material. This is demonstrated by testing the performance of the composite in supercapacitors. Faradaic reactions are exploited in an aqueous electrolyte through the high accessible surface of the incorporated small Fe2 O3 nanoparticles boosting the specific capacitance of the 3D turbostratic graphene network significantly.

Preparation and Properties of Metal Organic Framework/Activated Carbon Composite Materials.

Metal organic frameworks (MOFs) have unique properties that make them excellent candidates for many high-tech applications. Nevertheless, their nonconducting character is an obstacle to their practical utilization in electronic and energy systems. Using the familiar HKUST-1 MOF as a model, we present a new method of imparting electrical conductivity to otherwise nonconducting MOFs by preparing MOF nanoparticles within the conducting matrix of mesoporous activated carbon (AC). This composite material was studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), gas adsorption measurements, and electron paramagnetic resonance (EPR) spectroscopy. We show that MOF nanoparticles grown within the carbon matrix maintain their crystalline characteristics and their surface area. Surprisingly, as a result of the composition process, EPR measurements revealed a copper signal that had not yet been achieved. For the first time, we could analyze the complex EPR response of HKUST-1. We demonstrate the high conductivity of the MOF composite and discuss various factors that are responsible for these results. Finally, we present an optional application for using the conductive MOF composite as a high-performance electrode for pseudocapacitors.